· 6 years ago · Nov 01, 2019, 05:40 PM
1U-Boot SPL 2018.09-00002-g0b54a51eee (Sep 10 2018 - 19:41:39 -0500)
2Trying to boot from MMC1
3Loading Environment from EXT4... ** File not found /boot/uboot.env **
4
5** Unable to read "/boot/uboot.env" from mmc0:1 **
6
7
8U-Boot 2018.09-00002-g0b54a51eee (Sep 10 2018 - 19:41:39 -0500), Build: jenkins-github_Bootloader-Builder-65
9
10CPU : AM335X-GP rev 2.0
11I2C: ready
12DRAM: 512 MiB
13No match for driver 'omap_hsmmc'
14No match for driver 'omap_hsmmc'
15Some drivers were not found
16Reset Source: Power-on reset has occurred.
17RTC 32KCLK Source: External.
18MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
19Loading Environment from EXT4... ** File not found /boot/uboot.env **
20
21** Unable to read "/boot/uboot.env" from mmc0:1 **
22Board: BeagleBone Black
23<ethaddr> not set. Validating first E-fuse MAC
24BeagleBone Black:
25BeagleBone: cape eeprom: i2c_probe: 0x54:
26BeagleBone: cape eeprom: i2c_probe: 0x55:
27BeagleBone: cape eeprom: i2c_probe: 0x56:
28BeagleBone: cape eeprom: i2c_probe: 0x57:
29Net: eth0: MII MODE
30cpsw, usb_ether
31Press SPACE to abort autoboot in 2 seconds
32board_name=[A335BNLT] ...
33board_rev=[0A6A] ...
34switch to partitions #0, OK
35mmc0 is current device
36SD/MMC found on device 0
37switch to partitions #0, OK
38mmc0 is current device
39Scanning mmc 0:1…
40gpio: pin 56 (gpio 56) value is 0
41gpio: pin 55 (gpio 55) value is 0
42gpio: pin 54 (gpio 54) value is 0
43gpio: pin 53 (gpio 53) value is 1
44switch to partitions #0, OK
45mmc0 is current device
46gpio: pin 54 (gpio 54) value is 1
47Checking for: /uEnv.txt ...
48Checking for: /boot.scr ...
49Checking for: /boot/boot.scr ...
50Checking for: /boot/uEnv.txt ...
51gpio: pin 55 (gpio 55) value is 1
522041 bytes read in 9 ms (220.7 KiB/s)
53Loaded environment from /boot/uEnv.txt
54Checking if uname_r is set in /boot/uEnv.txt...
55gpio: pin 56 (gpio 56) value is 1
56Running uname_boot ...
57loading /boot/vmlinuz-4.14.71-ti-r80 ...
5810416640 bytes read in 667 ms (14.9 MiB/s)
59debug: [enable_uboot_overlays=1] ...
60debug: [enable_uboot_cape_universal=1] ...
61debug: [uboot_base_dtb_univ=am335x-boneblack-uboot-univ.dtb] ...
62uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot-univ.dtb] ...
63uboot_overlays: Switching too: dtb=am335x-boneblack-uboot-univ.dtb ...
64loading /boot/dtbs/4.14.71-ti-r80/am335x-boneblack-uboot-univ.dtb ...
65161723 bytes read in 30 ms (5.1 MiB/s)
66uboot_overlays: [fdt_buffer=0x60000] ...
67uboot_overlays: loading /lib/firmware/BB-BONE-eMMC1-01-00A0.dtbo ...
681440 bytes read in 72 ms (19.5 KiB/s)
69uboot_overlays: loading /lib/firmware/BB-HDMI-TDA998x-00A0.dtbo ...
705127 bytes read in 144 ms (34.2 KiB/s)
71uboot_overlays: loading /lib/firmware/BB-ADC-00A0.dtbo ...
72711 bytes read in 158 ms (3.9 KiB/s)
73uboot_overlays: loading /lib/firmware/AM335X-PRU-RPROC-4-14-TI-00A0.dtbo ...
743513 bytes read in 22 ms (155.3 KiB/s)
75loading /boot/initrd.img-4.14.71-ti-r80 ...
764530240 bytes read in 295 ms (14.6 MiB/s)
77debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh] ...
78debug: [bootz 0x82000000 0x88080000:452040 88000000] ...
79## Flattened Device Tree blob at 88000000
80 Booting using the fdt blob at 0x88000000
81 Loading Ramdisk to 8fbad000, end 8ffff040 ... OK
82 reserving fdt memory region: addr=88000000 size=89000
83 Loading Device Tree to 8fb21000, end 8fbacfff ... OK
84
85Starting kernel ...
86
87[ 0.000000] Booting Linux on physical CPU 0x0
88[ 0.000000] Linux version 4.14.71-ti-r80 (root@b2-am57xx-beagle-x15-2gb) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 SMP PREEMPT Fri Oct 5 23:50:11 UTC 2018
89[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
90[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
91[ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black
92[ 0.000000] Memory policy: Data cache writeback
93[ 0.000000] efi: Getting EFI parameters from FDT:
94[ 0.000000] efi: UEFI not found.
95[ 0.000000] cma: Reserved 48 MiB at 0x9c800000
96[ 0.000000] CPU: All CPU(s) started in SVC mode.
97[ 0.000000] AM335X ES2.0 (sgx neon)
98[ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x458 with crng_init=0
99[ 0.000000] percpu: Embedded 18 pages/cpu @df8e7000 s41548 r8192 d23988 u73728
100[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412
101[ 0.000000] Kernel command line: console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh
102[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
103[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
104[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
105[ 0.000000] Memory: 440272K/522240K available (13312K kernel code, 1169K rwdata, 4364K rodata, 1024K init, 361K bss, 32816K reserved, 49152K cma-reserved, 0K highmem)
106[ 0.000000] Virtual kernel memory layout:
107[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
108[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
109[ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB)
110[ 0.000000] lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB)
111
112[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
113[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
114[ 0.000000] .text : 0xc0008000 - 0xc0e00000 (14304 kB)
115[ 0.000000] .init : 0xc1400000 - 0xc1500000 (1024 kB)
116[ 0.000000] .data : 0xc1500000 - 0xc1624498 (1170 kB)
117[ 0.000000] .bss : 0xc162eb2c - 0xc1689000 ( 362 kB)
118[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
119[ 0.000000] ftrace: allocating 42734 entries in 126 pages
120[ 0.000000] Preemptible hierarchical RCU implementation.
121[ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
122[ 0.000000] Tasks RCU enabled.
123[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
124[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
125[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
126[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz
127[ 0.000024] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
128[ 0.000054] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
129[ 0.000068] OMAP clocksource: timer1 at 24000000 Hz
130[ 0.002124] timer_probe: no matching timers found
131[ 0.002463] Console: colour dummy device 80x30
132[ 0.002498] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
133[ 0.002506] This ensures that you still see kernel messages. Please
134[ 0.002513] update your kernel commandline.
135[ 0.002541] Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656)
136[ 0.021091] pid_max: default: 32768 minimum: 301
137[ 0.021365] Security Framework initialized
138[ 0.021386] Yama: becoming mindful.
139[ 0.021429] AppArmor: AppArmor disabled by boot time parameter
140[ 0.021510] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
141[ 0.021525] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
142[ 0.022549] CPU: Testing write buffer coherency: ok
143[ 0.023078] CPU0: thread -1, cpu 0, socket -1, mpidr 0
144[ 0.037175] Setting up static identity map for 0x80100000 - 0x80100060
145[ 0.045088] Hierarchical SRCU implementation.
146[ 0.056210] EFI services will not be available.
147[ 0.061096] smp: Bringing up secondary CPUs ...
148[ 0.061118] smp: Brought up 1 node, 1 CPU
149[ 0.061130] SMP: Total of 1 processors activated (995.32 BogoMIPS).
150[ 0.061142] CPU: All CPU(s) started in SVC mode.
151[ 0.062724] devtmpfs: initialized
152[ 0.101364] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
153[ 0.101851] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
154[ 0.101884] futex hash table entries: 256 (order: 2, 16384 bytes)
155[ 0.105807] xor: measuring software checksum speed
156[ 0.145109] arm4regs : 1200.000 MB/sec
157[ 0.185064] 8regs : 1075.000 MB/sec
158[ 0.225063] 32regs : 988.000 MB/sec
159[ 0.265062] neon : 1624.000 MB/sec
160[ 0.265073] xor: using function: neon (1624.000 MB/sec)
161[ 0.265095] pinctrl core: initialized pinctrl subsystem
162[ 0.266322] NET: Registered protocol family 16
163[ 0.269337] DMA: preallocated 256 KiB pool for atomic coherent allocations
164[ 0.360424] omap_hwmod: debugss: _wait_target_disable failed
165[ 0.401190] cpuidle: using governor menu
166[ 0.407591] OMAP GPIO hardware version 0.1
167[ 0.433195] No ATAGs?
168[ 0.433215] hw-breakpoint: debug architecture 0x4 unsupported.
169[ 0.434720] omap4_sram_init:Unable to allocate sram needed to handle errata I688
170[ 0.434745] omap4_sram_init:Unable to get sram pool needed to handle errata I688
171[ 0.529121] raid6: neonx2 gen() 1883 MB/s
172[ 0.597092] raid6: neonx2 xor() 1497 MB/s
173[ 0.597104] raid6: using algorithm neonx2 gen() 1883 MB/s
174[ 0.597114] raid6: .... xor() 1497 MB/s, rmw enabled
175[ 0.597124] raid6: using neon recovery algorithm
176[ 0.604902] edma 49000000.edma: TI EDMA DMA engine driver
177[ 0.611782] SCSI subsystem initialized
178[ 0.613561] usbcore: registered new interface driver usbfs
179[ 0.613638] usbcore: registered new interface driver hub
180[ 0.613758] usbcore: registered new device driver usb
181[ 0.614672] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe
182[ 0.615661] omap_i2c 4802a000.i2c: bus 1 rev0.11 at 100 kHz
183[ 0.616968] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz
184[ 0.617501] media: Linux media interface: v0.10
185[ 0.617564] Linux video capture interface: v2.00
186[ 0.617750] pps_core: LinuxPPS API ver. 1 registered
187[ 0.617764] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
188[ 0.617791] PTP clock support registered
189[ 0.618439] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400
190[ 0.621443] Advanced Linux Sound Architecture Driver Initialized.
191[ 0.622165] NetLabel: Initializing
192[ 0.622182] NetLabel: domain hash size = 128
193[ 0.622192] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
194[ 0.622281] NetLabel: unlabeled traffic allowed by default
195[ 0.625516] clocksource: Switched to clocksource timer1
196[ 0.789445] VFS: Disk quotas dquot_6.6.0
197[ 0.789692] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
198[ 0.802407] NET: Registered protocol family 2
199[ 0.803363] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
200[ 0.803416] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
201[ 0.803477] TCP: Hash tables configured (established 4096 bind 4096)
202[ 0.803601] UDP hash table entries: 256 (order: 1, 8192 bytes)
203[ 0.803627] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
204[ 0.803845] NET: Registered protocol family 1
205[ 0.812816] RPC: Registered named UNIX socket transport module.
206[ 0.812836] RPC: Registered udp transport module.
207[ 0.812845] RPC: Registered tcp transport module.
208[ 0.812853] RPC: Registered tcp NFSv4.1 backchannel transport module.
209[ 0.813887] Unpacking initramfs...
210[ 1.017583] random: fast init done
211[ 1.061713] Freeing initrd memory: 4428K
212[ 1.062282] hw perfevents: no interrupt-affinity property for /pmu, guessing.
213[ 1.062508] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available
214[ 1.064568] audit: initializing netlink subsys (disabled)
215[ 1.066054] audit: type=2000 audit(1.064:1): state=initialized audit_enabled=0 res=1
216[ 1.066209] workingset: timestamp_bits=14 max_order=17 bucket_order=3
217[ 1.072156] zbud: loaded
218[ 1.079850] NFS: Registering the id_resolver key type
219[ 1.079904] Key type id_resolver registered
220[ 1.079916] Key type id_legacy registered
221[ 1.079938] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
222[ 1.080320] fuse init (API version 7.26)
223[ 1.080932] SGI XFS with ACLs, security attributes, realtime, no debug enabled
224[ 1.100126] Key type asymmetric registered
225[ 1.100155] Asymmetric key parser 'x509' registered
226[ 1.100289] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
227[ 1.104634] io scheduler noop registered
228[ 1.104655] io scheduler deadline registered
229[ 1.105051] io scheduler cfq registered (default)
230[ 1.105065] io scheduler mq-deadline registered
231[ 1.107567] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
232[ 1.119620] gpio-of-helper ocp:cape-universal: ready
233[ 1.130548] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle
234[ 1.132790] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
235[ 1.136523] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a 8250
236[ 1.988191] console [ttyS0] enabled
237[ 1.992908] 48022000.serial: ttyS1 at MMIO 0x48022000 (irq = 31, base_baud = 3000000) is a 8250
238[ 2.002800] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 32, base_baud = 3000000) is a 8250
239[ 2.012668] 481a6000.serial: ttyS3 at MMIO 0x481a6000 (irq = 33, base_baud = 3000000) is a 8250
240[ 2.022603] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 34, base_baud = 3000000) is a 8250
241[ 2.032439] 481aa000.serial: ttyS5 at MMIO 0x481aa000 (irq = 35, base_baud = 3000000) is a 8250
242[ 2.044610] omap_rng 48310000.rng: Random Number Generator ver. 20
243[ 2.052259] [drm] Initialized vgem 1.0.0 20120112 for virtual device on minor 0
244[ 2.059882] usbcore: registered new interface driver udl
245[ 2.072878] at24 2-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
246[ 2.080205] at24 2-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
247[ 2.087398] at24 2-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
248[ 2.094572] at24 2-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
249[ 2.102053] eqep 48300180.eqep: ver. 1.0
250[ 2.106240] eqep 48300180.eqep: count_mode:0
251[ 2.110578] eqep 48300180.eqep: invert_qa:1
252[ 2.114808] eqep 48300180.eqep: invert_qb:1
253[ 2.119034] eqep 48300180.eqep: invert_qi:0
254[ 2.123261] eqep 48300180.eqep: invert_qs:0
255[ 2.127487] eqep 48300180.eqep: swap_inputs:0
256[ 2.131886] eqep 48300180.eqep: QDECCTL:0x0180
257[ 2.136373] eqep 48300180.eqep: QPOSINIT:0x00000000
258[ 2.141296] eqep 48300180.eqep: QPOSMAX:0xffffffff
259[ 2.146132] eqep 48300180.eqep: QPOSCNT:0x00000000
260[ 2.150968] eqep 48300180.eqep: omit_interrupt:0
261[ 2.155638] eqep 48300180.eqep: QEINT:0x0800
262[ 2.159950] eqep 48300180.eqep: QUPRD:0x05f5e100
263[ 2.164611] eqep 48300180.eqep: QEPCTL:0x009e write
264[ 2.169534] eqep 48300180.eqep: QEPCTL:0x009e read
265[ 2.174385] eqep 48300180.eqep: irq:135, clk_rate:100000000
266[ 2.180244] eqep 48302180.eqep: ver. 1.0
267[ 2.184364] eqep 48302180.eqep: count_mode:0
268[ 2.188695] eqep 48302180.eqep: invert_qa:1
269[ 2.192924] eqep 48302180.eqep: invert_qb:1
270[ 2.197151] eqep 48302180.eqep: invert_qi:0
271[ 2.201377] eqep 48302180.eqep: invert_qs:0
272[ 2.205605] eqep 48302180.eqep: swap_inputs:0
273[ 2.210004] eqep 48302180.eqep: QDECCTL:0x0180
274[ 2.214492] eqep 48302180.eqep: QPOSINIT:0x00000000
275[ 2.219414] eqep 48302180.eqep: QPOSMAX:0xffffffff
276[ 2.224249] eqep 48302180.eqep: QPOSCNT:0x00000000
277[ 2.229085] eqep 48302180.eqep: omit_interrupt:0
278[ 2.233746] eqep 48302180.eqep: QEINT:0x0800
279[ 2.238057] eqep 48302180.eqep: QUPRD:0x05f5e100
280[ 2.242717] eqep 48302180.eqep: QEPCTL:0x009e write
281[ 2.247638] eqep 48302180.eqep: QEPCTL:0x009e read
282[ 2.252487] eqep 48302180.eqep: irq:137, clk_rate:100000000
283[ 2.258300] eqep 48304180.eqep: ver. 1.0
284[ 2.262398] eqep 48304180.eqep: count_mode:0
285[ 2.266726] eqep 48304180.eqep: invert_qa:1
286[ 2.270954] eqep 48304180.eqep: invert_qb:1
287[ 2.275181] eqep 48304180.eqep: invert_qi:0
288[ 2.279406] eqep 48304180.eqep: invert_qs:0
289[ 2.283632] eqep 48304180.eqep: swap_inputs:0
290[ 2.288031] eqep 48304180.eqep: QDECCTL:0x0180
291[ 2.292517] eqep 48304180.eqep: QPOSINIT:0x00000000
292[ 2.297439] eqep 48304180.eqep: QPOSMAX:0xffffffff
293[ 2.302275] eqep 48304180.eqep: QPOSCNT:0x00000000
294[ 2.307111] eqep 48304180.eqep: omit_interrupt:0
295[ 2.311770] eqep 48304180.eqep: QEINT:0x0800
296[ 2.316082] eqep 48304180.eqep: QUPRD:0x05f5e100
297[ 2.320742] eqep 48304180.eqep: QEPCTL:0x009e write
298[ 2.325665] eqep 48304180.eqep: QEPCTL:0x009e read
299[ 2.330512] eqep 48304180.eqep: irq:139, clk_rate:100000000
300[ 2.365251] libphy: Fixed MDIO Bus: probed
301[ 2.370469] CAN device driver interface
302[ 2.375658] c_can_platform 481cc000.can: c_can_platform device registered (regs=fa1cc000, irq=42)
303[ 2.385679] c_can_platform 481d0000.can: c_can_platform device registered (regs=fa1d0000, irq=43)
304[ 2.449640] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000
305[ 2.457394] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
306[ 2.464640] MDIO: davinci_mdio: dt: updated phy_id[0] from phy_mask[fffffffe]
307[ 2.486544] libphy: 4a101000.mdio: probed
308[ 2.490867] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
309[ 2.501375] cpsw 4a100000.ethernet: Detected MACID = 90:59:af:64:76:d2
310[ 2.508238] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4
311[ 2.514725] cpsw 4a100000.ethernet: ALE Table size 1024
312[ 2.520070] cpsw 4a100000.ethernet: cpts: overflow check period 1250 (jiffies)
313[ 2.530955] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
314[ 2.537641] ehci-platform: EHCI generic platform driver
315[ 2.543300] ehci-omap: OMAP-EHCI Host Controller driver
316[ 2.549594] usbcore: registered new interface driver usb-storage
317[ 2.558968] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator
318[ 2.572387] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator
319[ 2.586884] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
320[ 2.592322] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1
321[ 2.600105] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
322[ 2.606974] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
323[ 2.614253] usb usb1: Product: MUSB HDRC host driver
324[ 2.619263] usb usb1: Manufacturer: Linux 4.14.71-ti-r80 musb-hcd
325[ 2.625406] usb usb1: SerialNumber: musb-hdrc.1
326[ 2.630899] hub 1-0:1.0: USB hub found
327[ 2.634876] hub 1-0:1.0: 1 port detected
328[ 2.651130] omap_rtc 44e3e000.rtc: registered as rtc0
329[ 2.657859] i2c /dev entries driver
330[ 2.662609] Driver for 1-wire Dallas network protocol.
331[ 2.671280] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
332[ 2.678891] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
333[ 2.688949] cpuidle: enable-method property 'ti,am3352' found operations
334[ 2.696670] sdhci: Secure Digital Host Controller Interface driver
335[ 2.702963] sdhci: Copyright(c) Pierre Ossman
336[ 2.708233] omap_hsmmc 48060000.mmc: Got CD GPIO
337[ 2.794202] sdhci-pltfm: SDHCI platform and OF driver helper
338[ 2.802455] ledtrig-cpu: registered to indicate activity on CPUs
339[ 2.812817] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
340[ 2.819026] omap-aes 53500000.aes: will run requests pump with realtime priority
341[ 2.829897] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
342[ 2.843485] hidraw: raw HID events driver (C) Jiri Kosina
343[ 2.849195] mmc0: host does not support reading read-only switch, assuming write-enable
344[ 2.857842] mmc0: new high speed SDHC card at address aaaa
345[ 2.864636] mmcblk0: mmc0:aaaa SC32G 29.7 GiB
346[ 2.870378] mmcblk0: p1
347[ 2.874578] usbcore: registered new interface driver usbhid
348[ 2.880366] usbhid: USB HID core driver
349[ 2.884804] remoteproc remoteproc0: wkup_m3 is available
350[ 2.899816] wireguard: WireGuard 0.0.20180925 loaded. See www.wireguard.com for information.
351[ 2.908552] wireguard: Copyright (C) 2015-2018 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
352[ 2.919110] NET: Registered protocol family 10
353[ 2.929232] Segment Routing with IPv6
354[ 2.933121] mip6: Mobile IPv6
355[ 2.936167] NET: Registered protocol family 17
356[ 2.940730] can: controller area network core (rev 20170425 abi 9)
357[ 2.947107] NET: Registered protocol family 29
358[ 2.951735] Key type dns_resolver registered
359[ 2.956060] mpls_gso: MPLS GSO support
360[ 2.960083] omap_voltage_late_init: Voltage driver support not added
361[ 2.967103] PM: Cannot get wkup_m3_ipc handle
362[ 2.971759] ThumbEE CPU extension supported.
363[ 2.976220] Registering SWP/SWPB emulation handler
364[ 2.982135] registered taskstats version 1
365[ 2.986499] zswap: loaded using pool lzo/zbud
366[ 2.993368] Btrfs loaded, crc32c=crc32c-generic
367[ 2.998123] ima: No TPM chip found, activating TPM-bypass! (rc=-19)
368[ 3.004546] ima: Allocated hash algorithm: sha256
369[ 3.164270] tda998x 0-0070: found TDA19988
370[ 3.170237] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_ops)
371[ 3.176366] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
372[ 3.183044] [drm] No driver support for vblank timestamp query.
373[ 3.189584] [drm] Cannot find any crtc or sizes
374[ 3.194960] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 1
375[ 3.217093] input: tps65217_pwr_but as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0
376[ 3.228544] tps65217 0-0024: TPS65217 ID 0xe version 1.2
377[ 3.234570] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
378[ 3.241720] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
379[ 3.249383] remoteproc remoteproc0: powering up wkup_m3
380[ 3.258807] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 217168
381[ 3.270061] mmc1: new high speed MMC card at address 0001
382[ 3.276151] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: no source widget found for Playback
383[ 3.276159] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: Failed to add route Playback -> direct -> TX
384[ 3.276786] remoteproc remoteproc0: remote processor wkup_m3 is now up
385[ 3.276814] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x193
386[ 3.310548] asoc-simple-card sound: i2s-hifi <-> 48038000.mcasp mapping ok
387[ 3.317620] mmcblk1: mmc1:0001 MMC02G 1.79 GiB
388[ 3.318094] mmcblk1boot0: mmc1:0001 MMC02G partition 1 1.00 MiB
389[ 3.323141] mmcblk1boot1: mmc1:0001 MMC02G partition 2 1.00 MiB
390[ 3.323545] mmcblk1rpmb: mmc1:0001 MMC02G partition 3 128 KiB
391[ 3.330669] mmcblk1: p1
392[ 3.349813] PM: bootloader does not support rtc-only!
393[ 3.356164] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
394[ 3.365009] of_cfs_init
395[ 3.367647] of_cfs_init: OK
396[ 3.371880] ALSA device list:
397[ 3.374992] #0: TI BeagleBone Black
398[ 3.383387] Freeing unused kernel memory: 1024K
399Loading, please wait...
400starting version 232
401[ 3.846107] random: systemd-udevd: uninitialized urandom read (16 bytes read)
402[ 3.858751] random: systemd-udevd: uninitialized urandom read (16 bytes read)
403[ 3.871034] random: udevadm: uninitialized urandom read (16 bytes read)
404[ 4.224837] [drm] Cannot find any crtc or sizes
405Begin: Loading essential drivers ... done.
406Begin: Running /scripts/init-premount ... done.
407Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
408Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems
409done.
410Warning: fsck not present, so skipping root file system
411[ 28.185172] EXT4-fs (mmcblk0p1): INFO: recovery required on readonly filesystem
412[ 28.192689] EXT4-fs (mmcblk0p1): write access will be enabled during recovery
413[ 28.498281] EXT4-fs (mmcblk0p1): recovery complete
414[ 28.511429] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
415done.
416Begin: Running /scripts/local-bottom ... done.
417Begin: Running /scripts/init-bottom ... done.
418
419================================================================================
420Starting eMMC Flasher from microSD media
421Version: [1.20180412: all ssh regneration override...]
422================================================================================
423
424================================================================================
425Prepare environment for flashing
426Starting at Sat Jan 1 00:00:26 UTC 2000
427----------------------------------------
428==> Giving system time to stablize…
4295 4 3 2 1
430==> Preparing /tmp
431==> Preparing sysctl
432==> sysctl: vm.min_free_kbytes=[2654]
433==> sysctl: setting: [sysctl -w vm.min_free_kbytes=16384]
434vm.min_free_kbytes = 16384
435----------------------------------------
436==> Determining root drive
437==> console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh
438----------------------------------------
439==> root_drive=[/dev/mmcblk0p1]
440====> Root drive identified at [/dev/mmcblk0p1]
441==> Boot Drive [/dev/mmcblk0p1]
442==> Figuring out Source and Destination devices
443====> Source identified: [/dev/mmcblk0]
444====> Destination identified: [/dev/mmcblk1]
445==> Figuring out machine
446====> Machine is TI_AM335x_BeagleBone_Black
447====> Machine is compatible with BeagleBone Black
448================================================================================
4495 4 3 2 1
450
451========================================
452Checking for Valid bbb-eeprom header
453==> Valid bbb-eeprom header found [335]
454========================================
455
456================================================================================
457Checking running system
458==> Copying: [/dev/mmcblk0] -> [/dev/mmcblk1]
459==> lsblk:
460----------------------------------------
461NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
462mmcblk0 179:0 0 29.7G 0 disk
463`-mmcblk0p1 179:1 0 29.7G 0 part /
464mmcblk1 179:8 0 1.8G 0 disk
465`-mmcblk1p1 179:9 0 1.8G 0 part
466mmcblk1boot0 179:16 0 1M 1 disk
467mmcblk1boot1 179:24 0 1M 1 disk
468mmcblk1rpmb 179:32 0 128K 0 disk
469----------------------------------------
470==> df -h | grep rootfs:
471----------------------------------------
472==> Giving you time to check...
47310 9 8 7 6 5 4 3 2 1
474================================================================================
475
476================================================================================
477Preparing drives
478
479----------------------------------------
480==> Erasing: /dev/mmcblk1
481----------------------------------------
482[ 56.721419] random: crng init done
483[ 56.724869] random: 7 urandom warning(s) missed due to ratelimiting
484108+0 records in
485108+0 records out
486113246208 bytes (113 MB, 108 MiB) copied, 21.661 s, 5.2 MB/s
487----------------------------------------
488108+0 records in
489108+0 records out
490113246208 bytes (113 MB, 108 MiB) copied, 4.27427 s, 26.5 MB/s
491----------------------------------------
492==> Erasing: /dev/mmcblk1 complete
493----------------------------------------
494
495----------------------------------------
496==> Loading /boot/SOC.sh
497************************************************************
498#!/bin/sh
499format=1.0
500
501board=am335x_evm
502
503bootloader_location=dd_spl_uboot_boot
504bootrom_gpt=
505
506dd_spl_uboot_count=1
507dd_spl_uboot_seek=1
508dd_spl_uboot_conf=notrunc
509dd_spl_uboot_bs=128k
510dd_spl_uboot_backup=/opt/backup/uboot/MLO
511
512dd_uboot_count=2
513dd_uboot_seek=1
514dd_uboot_conf=notrunc
515dd_uboot_bs=384k
516dd_uboot_backup=/opt/backup/uboot/u-boot.img
517
518boot_fstype=ext4
519conf_boot_startmb=4
520conf_boot_endmb=
521sfdisk_fstype=L
522
523boot_label=BOOT
524rootfs_label=rootfs
525
526#Kernel
527dtb=
528serial_tty=ttyO0
529usbnet_mem=
530
531#Advanced options
532#disable_ssh_regeneration=true
533
534************************************************************
535==> Loaded
536
537----------------------------------------
538
539================================================================================
540Writing bootloader to [/dev/mmcblk1]
541----------------------------------------
542==> Figuring out options for SPL U-Boot copy ...
543===> Will use : count=1 seek=1 conv=notrunc bs=128k
544==> Figuring out options for U-Boot copy ...
545===> Will use : count=2 seek=1 conv=notrunc bs=384k
546==> Copying SPL U-Boot with dd if=/opt/backup/uboot/MLO of=/dev/mmcblk1 count=1 seek=1 conv=notrunc bs=128k
547
5480+1 records in
5490+1 records out
55090932 bytes (91 kB, 89 KiB) copied, 0.0259515 s, 3.5 MB/s
551------------------------------------------------------------
552==> Copying U-Boot with dd if=/opt/backup/uboot/u-boot.img of=/dev/mmcblk1 count=2 seek=1 conv=notrunc bs=384k
553------------------------------------------------------------
5541+1 records in
5551+1 records out
556447372 bytes (447 kB, 437 KiB) copied, 0.135903 s, 3.3 MB/s
557------------------------------------------------------------
558Writing bootloader completed
559================================================================================
560
561================================================================================
562Partitionning /dev/mmcblk1
563----------------------------------------
564sfdisk: [2.26.x or greater]
565==> sfdisk parameters:
566sfdisk: [sfdisk from util-linux 2.29.2]
567sfdisk: [sfdisk --force /dev/mmcblk1]
568sfdisk: [4M,,L,*]
569==> Partitionning
570------------------------------------------------------------
571Checking that no-one is using this disk right now ... OK
572
573Disk /dev/mmcblk1: 1.8 GiB, 1920991232 bytes, 3751936 sectors
574Units: sectors of 1 * 512 = 512 bytes
575Sector size (logical/physical): 512 bytes / 512 bytes
576I/O size (minimum/optimal): 512 bytes / 512 bytes
577
578>>> Created a new DOS disklabel with disk identifier 0x67ed0136.
579/dev/mmcblk1p1: Created a new partition 1 of type 'Linux' and of size 1.8 GiB.
580/dev/mmcblk1p2: Done.
581
582New situation:
583
584Device Boot Start End Sectors Size Id Type
585/dev/mmcblk1p1 * 8192 3751935 3743744 1.8G 83 Linux
586The partition table has been altered.
587Calling ioctl([ 77.286720] mmcblk1: p1
588) to re-read partition table.
589Syncing disks.
590------------------------------------------------------------
591
592==> Partitionning Completed
593==> Generated Partitions:
594------------------------------------------------------------
595Disk /dev/mmcblk1: 1.8 GiB, 1920991232 bytes, 3751936 sectors
596Units: sectors of 1 * 512 = 512 bytes
597Sector size (logical/physical): 512 bytes / 512 bytes
598I/O size (minimum/optimal): 512 bytes / 512 bytes
599Disklabel type: dos
600Disk identifier: 0x67ed0136
601
602Device Boot Start End Sectors Size Id Type
603/dev/mmcblk1p1 * 8192 3751935 3743744 1.8G 83 Linux
604------------------------------------------------------------
605================================================================================
606
607================================================================================
608Preparing future rootfs to receive files
609----------------------------------------
610
611==> Formatting rootfs with mkfs.ext4 -O ^metadata_csum,^64bit /dev/mmcblk1p1 -L rootfs
612--------------------------------------------------------------------------------
613
614mke2fs 1.43.4 (31-Jan-2017)
615Discarding device blocks: done
616Creating filesystem with 467968 4k blocks and 117120 inodes
617Filesystem UUID: cf4a68a4-61a1-4a84-9216-8da6e934d211
618Superblock backups stored on blocks:
619 32768, 98304, 163840, 229376, 294912
620
621Allocating group tables: done
622Writing inode tables: done
623Creating journal (8192 blocks): done
624Writing superblocks and filesystem accounting information: done
625
626
627--------------------------------------------------------------------------------
628==> Formatting rootfs: /dev/mmcblk1p1 complete
629==> Creating temporary rootfs directory (/tmp/rootfs)
630==> Mounting /dev/mmcblk1p1 to /tmp/rootfs
631[ 96.444310] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null)
632
633================================================================================
634
635================================================================================
636Copying: Current rootfs to /dev/mmcblk1p1
637----------------------------------------
638==> rsync: / -> /tmp/rootfs
639----------------------------------------
640rsync: write failed on "/tmp/rootfs/usr/share/vim/vim80/syntax/csdl.vim": No space left on device (28)
641rsync error: error in file IO (code 11) at receiver.c(393) [receiver=3.1.2]
642writing to [/dev/mmcblk1] failed...
643==> Stopping Cylon LEDs ...
644==> Setting LEDs to
645/opt/scripts/tools/eMMC/functions.sh: line 391: 959 Terminated cylon_leds
646----------------------------------------
647Your foo is weak.