· 6 years ago · Mar 27, 2020, 12:30 AM
1U-Boot SPL 2019.10 (Dec 22 2019 - 00:56:27 +0000)
2DRAM: 1024 MiB
3CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
4Trying to boot from MMC1
5
6
7U-Boot 2019.10 (Dec 22 2019 - 00:56:27 +0000) Allwinner Technology
8
9CPU: Allwinner A20 (SUN7I)
10Model: Olimex A20-OLinuXino-LIME2
11I2C: ready
12DRAM: 1 GiB
13MMC: mmc@1c0f000: 0
14Loading Environment from FAT... Unable to use mmc 0:1... In: serial
15Out: serial
16Err: serial
17Allwinner mUSB OTG (Peripheral)
18Net: eth0: ethernet@1c50000
19Warning: usb_ether using MAC address from ROM
20, eth1: usb_ether
21starting USB...
22Bus usb@1c14000: USB EHCI 1.00
23Bus usb@1c14400: USB OHCI 1.0
24Bus usb@1c1c000: USB EHCI 1.00
25Bus usb@1c1c400: USB OHCI 1.0
26scanning bus usb@1c14000 for devices... 1 USB Device(s) found
27scanning bus usb@1c14400 for devices... 1 USB Device(s) found
28scanning bus usb@1c1c000 for devices... 1 USB Device(s) found
29scanning bus usb@1c1c400 for devices... 1 USB Device(s) found
30 scanning usb for storage devices... 0 Storage Device(s) found
31Hit any key to stop autoboot: 0
32switch to partitions #0, OK
33mmc0 is current device
34Scanning mmc 0:1...
35Found U-Boot script /boot.scr
36465 bytes read in 2 ms (226.6 KiB/s)
37## Executing script at 43100000
3826002 bytes read in 8 ms (3.1 MiB/s)
398112328 bytes read in 461 ms (16.8 MiB/s)
40## Flattened Device Tree blob at 43000000
41 Booting using the fdt blob at 0x43000000
42EHCI failed to shut down host controller.
43 Loading Device Tree to 49ff6000, end 49fff591 ... OK
44
45Starting kernel ...
46
47Uncompressing Linux... done, booting the kernel.
48[ 0.000000] Booting Linux on physical CPU 0x0
49[ 0.000000] Linux version 5.5.0 (tuxd3v@desktop0) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #5 SMP Wed Jan 29 03:10:16 WET 2020
50[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=50c5387d
51[ 0.000000] CPU: div instructions available: patching division code
52[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
53[ 0.000000] OF: fdt: Machine model: Olimex A20-OLinuXino-LIME2
54[ 0.000000] Memory policy: Data cache writealloc
55[ 0.000000] Reserved memory: created CMA memory pool at 0x4a000000, size 96 MiB
56[ 0.000000] OF: reserved mem: initialized node default-pool, compatible id shared-dma-pool
57[ 0.000000] On node 0 totalpages: 262144
58[ 0.000000] Normal zone: 1728 pages used for memmap
59[ 0.000000] Normal zone: 0 pages reserved
60[ 0.000000] Normal zone: 196608 pages, LIFO batch:63
61[ 0.000000] HighMem zone: 65536 pages, LIFO batch:15
62[ 0.000000] psci: probing for conduit method from DT.
63[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
64[ 0.000000] percpu: Embedded 20 pages/cpu s49932 r8192 d23796 u81920
65[ 0.000000] pcpu-alloc: s49932 r8192 d23796 u81920 alloc=20*4096
66[ 0.000000] pcpu-alloc: [0] 0 [0] 1
67[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416
68[ 0.000000] Kernel command line: debug=on console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait fsck.repair=yes panic=15
69[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
70[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
71[ 0.000000] allocated 1048576 bytes of page_ext
72[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
73[ 0.000000] Memory: 923008K/1048576K available (9216K kernel code, 1087K rwdata, 2964K rodata, 1024K init, 331K bss, 27264K reserved, 98304K cma-reserved, 262144K highmem)
74[ 0.000000] random: get_random_u32 called from __kmem_cache_create+0x2b/0x3ac with crng_init=0
75[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
76[ 0.000000] ftrace: allocating 42295 entries in 83 pages
77[ 0.000000] ftrace: allocated 83 pages with 4 groups
78[ 0.000000] rcu: Hierarchical RCU implementation.
79[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
80[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
81[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
82[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
83[ 0.000000] GIC: Using split EOI/Deactivate mode
84[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
85[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
86[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
87[ 0.000019] Switching to timer-based delay loop, resolution 41ns
88[ 0.000445] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
89[ 0.000771] clocksource: hstimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
90[ 0.001048] Console: colour dummy device 80x30
91[ 0.001111] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
92[ 0.001124] pid_max: default: 32768 minimum: 301
93[ 0.001349] LSM: Security Framework initializing
94[ 0.001462] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
95[ 0.001476] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
96[ 0.002655] CPU: Testing write buffer coherency: ok
97[ 0.003138] /cpus/cpu@0 missing clock-frequency property
98[ 0.003168] /cpus/cpu@1 missing clock-frequency property
99[ 0.003180] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
100[ 0.003902] Setting up static identity map for 0x40100000 - 0x40100054
101[ 0.004076] rcu: Hierarchical SRCU implementation.
102[ 0.004760] smp: Bringing up secondary CPUs ...
103[ 0.015592] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
104[ 0.015772] smp: Brought up 1 node, 2 CPUs
105[ 0.015786] SMP: Total of 2 processors activated (96.00 BogoMIPS).
106[ 0.015793] CPU: All CPU(s) started in HYP mode.
107[ 0.015798] CPU: Virtualization extensions available.
108[ 0.016719] devtmpfs: initialized
109[ 0.023455] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
110[ 0.023834] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
111[ 0.023861] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
112[ 0.028009] xor: measuring software checksum speed
113[ 0.067537] arm4regs : 1136.000 MB/sec
114[ 0.107596] 8regs : 791.000 MB/sec
115[ 0.147650] 32regs : 747.000 MB/sec
116[ 0.187711] neon : 1149.000 MB/sec
117[ 0.187718] xor: using function: neon (1149.000 MB/sec)
118[ 0.187811] pinctrl core: initialized pinctrl subsystem
119[ 0.188417] thermal_sys: Registered thermal governor 'fair_share'
120[ 0.188423] thermal_sys: Registered thermal governor 'bang_bang'
121[ 0.188433] thermal_sys: Registered thermal governor 'step_wise'
122[ 0.189397] NET: Registered protocol family 16
123[ 0.191105] DMA: preallocated 256 KiB pool for atomic coherent allocations
124[ 0.191862] audit: initializing netlink subsys (disabled)
125[ 0.192142] audit: type=2000 audit(0.184:1): state=initialized audit_enabled=0 res=1
126[ 0.192669] cpuidle: using governor ladder
127[ 0.192716] cpuidle: using governor menu
128[ 0.193089] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
129[ 0.193098] hw-breakpoint: maximum watchpoint size is 8 bytes.
130[ 0.300438] raid6: neonx8 gen() 641 MB/s
131[ 0.368564] raid6: neonx8 xor() 534 MB/s
132[ 0.436775] raid6: neonx4 gen() 658 MB/s
133[ 0.504835] raid6: neonx4 xor() 557 MB/s
134[ 0.573000] raid6: neonx2 gen() 599 MB/s
135[ 0.641133] raid6: neonx2 xor() 529 MB/s
136[ 0.709270] raid6: neonx1 gen() 447 MB/s
137[ 0.777433] raid6: neonx1 xor() 423 MB/s
138[ 0.845641] raid6: int32x8 gen() 242 MB/s
139[ 0.913739] raid6: int32x8 xor() 157 MB/s
140[ 0.982069] raid6: int32x4 gen() 258 MB/s
141[ 1.050086] raid6: int32x4 xor() 177 MB/s
142[ 1.118342] raid6: int32x2 gen() 231 MB/s
143[ 1.186371] raid6: int32x2 xor() 187 MB/s
144[ 1.254465] raid6: int32x1 gen() 180 MB/s
145[ 1.322620] raid6: int32x1 xor() 159 MB/s
146[ 1.322627] raid6: using algorithm neonx4 gen() 658 MB/s
147[ 1.322632] raid6: .... xor() 557 MB/s, rmw enabled
148[ 1.322639] raid6: using neon recovery algorithm
149[ 1.324574] iommu: Default domain type: Translated
150[ 1.325006] SCSI subsystem initialized
151[ 1.325475] libata version 3.00 loaded.
152[ 1.325746] usbcore: registered new interface driver usbfs
153[ 1.325807] usbcore: registered new interface driver hub
154[ 1.325878] usbcore: registered new device driver usb
155[ 1.326147] mc: Linux media interface: v0.10
156[ 1.326185] videodev: Linux video capture interface: v2.00
157[ 1.326318] pps_core: LinuxPPS API ver. 1 registered
158[ 1.326326] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
159[ 1.326357] PTP clock support registered
160[ 1.328323] clocksource: Switched to clocksource arch_sys_counter
161[ 2.404085] VFS: Disk quotas dquot_6.6.0
162[ 2.404187] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
163[ 2.413145] NET: Registered protocol family 2
164[ 2.414031] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
165[ 2.414070] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
166[ 2.414147] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
167[ 2.414273] TCP: Hash tables configured (established 8192 bind 8192)
168[ 2.414415] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
169[ 2.414481] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
170[ 2.414774] NET: Registered protocol family 1
171[ 2.415503] RPC: Registered named UNIX socket transport module.
172[ 2.415519] RPC: Registered udp transport module.
173[ 2.415525] RPC: Registered tcp transport module.
174[ 2.415531] RPC: Registered tcp NFSv4.1 backchannel transport module.
175[ 2.416439] hw perfevents: no interrupt-affinity property for /pmu, guessing.
176[ 2.416720] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
177[ 2.418316] Initialise system trusted keyrings
178[ 2.418613] workingset: timestamp_bits=14 max_order=18 bucket_order=4
179[ 2.425832] zbud: loaded
180[ 2.428800] NFS: Registering the id_resolver key type
181[ 2.428846] Key type id_resolver registered
182[ 2.428853] Key type id_legacy registered
183[ 2.428870] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
184[ 2.428877] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
185[ 2.430489] JFS: nTxBlock = 7979, nTxLock = 63832
186[ 2.441547] SGI XFS with ACLs, security attributes, realtime, quota, no debug enabled
187[ 2.486839] Key type asymmetric registered
188[ 2.486857] Asymmetric key parser 'x509' registered
189[ 2.486931] bounce: pool size: 64 pages
190[ 2.487010] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
191[ 2.487202] io scheduler mq-deadline registered
192[ 2.487211] io scheduler kyber registered
193[ 2.487292] io scheduler bfq registered
194[ 2.488599] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO
195[ 2.492028] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
196[ 2.551852] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
197[ 2.554013] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pb not found, using dummy regulator
198[ 2.554997] printk: console [ttyS0] disabled
199[ 2.575204] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 46, base_baud = 1500000) is a U6_16550A
200[ 3.460675] printk: console [ttyS0] enabled
201[ 3.466764] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0
202[ 3.477287] sun4i-drm display-engine: bound 1e00000.display-frontend (ops 0xc0a8d718)
203[ 3.485260] sun4i-drm display-engine: bound 1e20000.display-frontend (ops 0xc0a8d718)
204[ 3.493416] sun4i-drm display-engine: bound 1e60000.display-backend (ops 0xc0a8cf58)
205[ 3.501459] sun4i-drm display-engine: bound 1e40000.display-backend (ops 0xc0a8cf58)
206[ 3.509745] sun4i-drm display-engine: No panel or bridge found... RGB output disabled
207[ 3.517607] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc0a8bc80)
208[ 3.525715] sun4i-drm display-engine: No panel or bridge found... RGB output disabled
209[ 3.533575] sun4i-drm display-engine: bound 1c0d000.lcd-controller (ops 0xc0a8bc80)
210[ 3.542278] rc_core: Couldn't load IR keymap rc-cec
211[ 3.547211] Registered IR keymap rc-empty
212[ 3.551380] rc rc0: sun4i as /devices/platform/soc/1c16000.hdmi/rc/rc0
213[ 3.558082] input: sun4i as /devices/platform/soc/1c16000.hdmi/rc/rc0/input0
214[ 3.565434] sun4i-drm display-engine: bound 1c16000.hdmi (ops 0xc0a8ddb0)
215[ 3.572255] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
216[ 3.578876] [drm] No driver support for vblank timestamp query.
217[ 3.585271] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 1
218[ 4.093111] [drm] Cannot find any crtc or sizes
219[ 4.102181] brd: module loaded
220[ 4.113640] loop: module loaded
221[ 4.117776] ahci-sunxi 1c18000.sata: 1c18000.sata supply ahci not found, using dummy regulator
222[ 4.126524] ahci-sunxi 1c18000.sata: 1c18000.sata supply phy not found, using dummy regulator
223[ 4.137050] libphy: Fixed MDIO Bus: probed
224[ 4.142157] sun7i-dwmac 1c50000.ethernet: IRQ eth_wake_irq not found
225[ 4.148542] sun7i-dwmac 1c50000.ethernet: IRQ eth_lpi not found
226[ 4.154579] sun7i-dwmac 1c50000.ethernet: PTP uses main clock
227[ 4.160341] sun7i-dwmac 1c50000.ethernet: no reset control found
228[ 4.166394] sun7i-dwmac 1c50000.ethernet: no regulator found
229[ 4.172437] sun7i-dwmac 1c50000.ethernet: Version ID not available
230[ 4.178659] sun7i-dwmac 1c50000.ethernet: DWMAC1000
231[ 4.183653] sun7i-dwmac 1c50000.ethernet: DMA HW capability register supported
232[ 4.190902] sun7i-dwmac 1c50000.ethernet: Normal descriptors
233[ 4.196568] sun7i-dwmac 1c50000.ethernet: Ring mode enabled
234[ 4.202386] libphy: stmmac: probed
235[ 4.209030] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
236[ 4.215600] ehci-platform: EHCI generic platform driver
237[ 4.221303] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
238[ 4.227536] ohci-platform: OHCI generic platform driver
239[ 4.233576] usbcore: registered new interface driver usb-storage
240[ 4.240938] sunxi-rtc 1c20d00.rtc: registered as rtc0
241[ 4.246205] i2c /dev entries driver
242[ 4.250914] axp20x-i2c 1-0034: AXP20x variant AXP209 found
243[ 4.271606] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-1/1-0034/axp20x-pek/input/input1
244[ 4.281775] ldo1: supplied by regulator-dummy
245[ 4.286521] ldo2: supplied by regulator-dummy
246[ 4.292051] ldo3: supplied by regulator-dummy
247[ 4.297861] ldo4: supplied by regulator-dummy
248[ 4.302325] vddio-csi1: Bringing 3000000uV into 2800000-2800000uV
249[ 4.308965] ldo5: supplied by regulator-dummy
250[ 4.314011] dcdc2: supplied by regulator-dummy
251[ 4.319230] dcdc3: supplied by regulator-dummy
252[ 4.325456] axp20x-i2c 1-0034: AXP20X driver loaded
253[ 4.332998] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
254[ 4.342453] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-ph not found, using dummy regulator
255[ 4.352206] sunxi-mmc 1c0f000.mmc: Got CD GPIO
256[ 4.382345] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB
257[ 4.390815] ledtrig-cpu: registered to indicate activity on CPUs
258[ 4.397189] sun4i-ss 1c15000.crypto-engine: Die ID 0
259[ 4.405666] hid: raw HID events driver (C) Jiri Kosina
260[ 4.411048] usbcore: registered new interface driver usbhid
261[ 4.416648] usbhid: USB HID core driver
262[ 4.417761] random: fast init done
263[ 4.421680] Initializing XFRM netlink socket
264[ 4.428910] NET: Registered protocol family 10
265[ 4.430506] mmc0: host does not support reading read-only switch, assuming write-enable
266[ 4.443378] Segment Routing with IPv6
267[ 4.447250] NET: Registered protocol family 17
268[ 4.451756] NET: Registered protocol family 15
269[ 4.456330] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
270[ 4.469693] mmc0: new high speed SDHC card at address 5048
271[ 4.472365] 8021q: 802.1Q VLAN Support v1.8
272[ 4.476245] mmcblk0: mmc0:5048 SD32G 29.0 GiB
273[ 4.479784] Key type dns_resolver registered
274[ 4.488532] Registering SWP/SWPB emulation handler
275[ 4.490959] mmcblk0: p1 p2
276[ 4.493954] registered taskstats version 1
277[ 4.500364] Loading compiled-in X.509 certificates
278[ 4.505338] zswap: loaded using pool lzo/zbud
279[ 4.510047] Key type ._fscrypt registered
280[ 4.514094] Key type .fscrypt registered
281[ 4.521287] Btrfs loaded, crc32c=crc32c-generic
282[ 4.527064] Key type encrypted registered
283[ 4.549459] ahci-sunxi 1c18000.sata: 1c18000.sata supply ahci not found, using dummy regulator
284[ 4.558261] ahci-sunxi 1c18000.sata: 1c18000.sata supply phy not found, using dummy regulator
285[ 4.620356] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
286[ 4.627861] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
287[ 4.633758] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
288[ 4.642729] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
289[ 4.651820] scsi host0: ahci-sunxi
290[ 4.655755] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 36
291[ 4.664468] ehci-platform 1c14000.usb: EHCI Host Controller
292[ 4.670099] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
293[ 4.678194] ehci-platform 1c14000.usb: irq 32, io mem 0x01c14000
294[ 4.696339] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
295[ 4.702677] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05
296[ 4.710957] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
297[ 4.718188] usb usb1: Product: EHCI Host Controller
298[ 4.723075] usb usb1: Manufacturer: Linux 5.5.0 ehci_hcd
299[ 4.728392] usb usb1: SerialNumber: 1c14000.usb
300[ 4.733669] hub 1-0:1.0: USB hub found
301[ 4.737494] hub 1-0:1.0: 1 port detected
302[ 4.742487] ehci-platform 1c1c000.usb: EHCI Host Controller
303[ 4.748122] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
304[ 4.756158] ehci-platform 1c1c000.usb: irq 37, io mem 0x01c1c000
305[ 4.776333] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
306[ 4.782663] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05
307[ 4.790942] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
308[ 4.798169] usb usb2: Product: EHCI Host Controller
309[ 4.803055] usb usb2: Manufacturer: Linux 5.5.0 ehci_hcd
310[ 4.808372] usb usb2: SerialNumber: 1c1c000.usb
311[ 4.813611] hub 2-0:1.0: USB hub found
312[ 4.817434] hub 2-0:1.0: 1 port detected
313[ 4.822378] ohci-platform 1c14400.usb: Generic Platform OHCI controller
314[ 4.829045] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
315[ 4.837086] ohci-platform 1c14400.usb: irq 33, io mem 0x01c14400
316[ 4.904521] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.05
317[ 4.912804] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
318[ 4.920028] usb usb3: Product: Generic Platform OHCI controller
319[ 4.925955] usb usb3: Manufacturer: Linux 5.5.0 ohci_hcd
320[ 4.931272] usb usb3: SerialNumber: 1c14400.usb
321[ 4.936570] hub 3-0:1.0: USB hub found
322[ 4.940392] hub 3-0:1.0: 1 port detected
323[ 4.945364] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
324[ 4.952035] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
325[ 4.960088] ohci-platform 1c1c400.usb: irq 38, io mem 0x01c1c400
326[ 4.978836] ata1: SATA link down (SStatus 0 SControl 300)
327[ 5.028550] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.05
328[ 5.036832] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
329[ 5.044058] usb usb4: Product: Generic Platform OHCI controller
330[ 5.049986] usb usb4: Manufacturer: Linux 5.5.0 ohci_hcd
331[ 5.055304] usb usb4: SerialNumber: 1c1c400.usb
332[ 5.060573] hub 4-0:1.0: USB hub found
333[ 5.064396] hub 4-0:1.0: 1 port detected
334[ 5.069466] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
335[ 5.080930] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
336[ 5.086727] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 5
337[ 5.094870] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05
338[ 5.103159] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
339[ 5.110394] usb usb5: Product: MUSB HDRC host driver
340[ 5.115366] usb usb5: Manufacturer: Linux 5.5.0 musb-hcd
341[ 5.120684] usb usb5: SerialNumber: musb-hdrc.1.auto
342[ 5.126277] hub 5-0:1.0: USB hub found
343[ 5.130098] hub 5-0:1.0: 1 port detected
344[ 5.135369] sunxi-rtc 1c20d00.rtc: setting system clock to 2020-03-27T00:21:36 UTC (1585268496)
345[ 5.185386] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
346[ 5.193619] VFS: Mounted root (ext4 filesystem) on device 179:2.
347[ 5.208516] devtmpfs: mounted
348[ 5.215130] Freeing unused kernel memory: 1024K
349[ 5.219967] Run /sbin/init as init process
350INIT: version 2.93 booting
351[info] Using makefile-style concurrent boot in runlevel S.
352ERROR: could not open /proc/stat: No such file or directory
353[FAIL] Cleaning up temporary files... /tmp failed!
354[....] Starting hot-plug events dispatcher: udevd[ 6.718071] udevd[377]: starting version 3.2.7
355[ 6.761795] random: udevd: uninitialized urandom read (16 bytes read)
356[ 6.774869] random: udevd: uninitialized urandom read (16 bytes read)
357[ ok [ 6.783137] random: udevd: uninitialized urandom read (16 bytes read)
358.
359[....] Synthesizing the initial hotplug events...[ 6.861536] udevd[377]: starting eudev-3.2.7
360done.
361[....] Waiting for /dev to be fully populated...[ 7.304531] sunxi_cedrus: module is from the staging directory, the quality is unknown, you have been warned.
362[ 7.418506] cedrus 1c0e000.video-codec: Device registered as /dev/video0
363[ 7.513993] at24 2-0050: 2048 byte 24c16 EEPROM, writable, 16 bytes/write
364[ 7.534336] lima 1c40000.gpu: IRQ ppmmu2 not found
365[ 7.539251] lima 1c40000.gpu: IRQ ppmmu3 not found
366[ 7.544118] lima 1c40000.gpu: gp - mali400 version major 1 minor 1
367[ 7.550449] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1
368[ 7.556846] lima 1c40000.gpu: pp1 - mali400 version major 1 minor 1
369[ 7.563241] lima 1c40000.gpu: IRQ pp2 not found
370[ 7.567829] lima 1c40000.gpu: IRQ pp3 not found
371[ 7.572395] lima 1c40000.gpu: l2 cache 64K, 4-way, 64byte cache line, 64bit external bus
372[ 7.583276] lima 1c40000.gpu: bus rate = 300000000
373[ 7.588215] lima 1c40000.gpu: mod rate = 384000000
374[ 7.595665] [drm] Initialized lima 1.0.0 20190217 for 1c40000.gpu on minor 2
375[ 7.620540] axp20x-adc axp20x-adc: DMA mask not set
376[ 7.637939] axp20x-gpio axp20x-gpio: DMA mask not set
377[ 7.645859] axp20x-battery-power-supply axp20x-battery-power-supply: DMA mask not set
378[ 7.646039] axp20x-ac-power-supply axp20x-ac-power-supply: DMA mask not set
379[ 7.665018] axp20x-gpio axp20x-gpio: AXP209 pinctrl and GPIO driver loaded
380[ 8.112769] sun7i-dwmac 1c50000.ethernet eth0: PHY [stmmac-0:01] driver [RTL8211E Gigabit Ethernet]
381[ 8.132408] sun7i-dwmac 1c50000.ethernet eth0: No Safety Features support found
382[ 8.139854] sun7i-dwmac 1c50000.ethernet eth0: RX IPC Checksum Offload disabled
383[ 8.147221] sun7i-dwmac 1c50000.ethernet eth0: No MAC Management Counters available
384[ 8.154919] sun7i-dwmac 1c50000.ethernet eth0: PTP not supported by HW
385[ 8.161480] sun7i-dwmac 1c50000.ethernet eth0: configuring for phy/rgmii link mode
386done.
387[ ok ] Activating swap...done.
388mount: /: mount point is busy.
389[FAIL] Cannot check root file system because it is not mounted read-only. ... failed!
390[ 10.271739] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
391[....] Checking file systems...[ 11.241524] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx
392[ 11.250093] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
393fsck from util-linux 2.33.1
394/dev/mmcblk0p1: clean, 16/24384 files, 16804/97280 blocks
395[ 11.492144] random: crng init done
396[ 11.495561] random: 4 urandom warning(s) missed due to ratelimiting
397done.
398[ ok ] Cleaning up temporary files... /tmp.
399[info] Loading kernel module zram.
400[ 11.880133] zram: Added device: zram0
401[ 11.885528] zram: Added device: zram1
402[....] Starting Setting kernel variables: sysctl[ 11.973873] zram0: detected capacity change from 0 to 349175808
403[ 11.974049] zram1: detected capacity change from 0 to 349175808
404. ok
405[....] Configuring network interfaces...ifup: waiting for lock on /run/network/ifstate.eth0
406[ 14.800474] [drm] Cannot find any crtc or sizes
407ifup: interface eth0 already configured
408done.
409[ ok ] Cleaning up temporary files....
410[ ok ] Setting up ALSA...done (none loaded).
411[FAIL] startpar: service(s) returned failure: mountall-bootclean.sh ... failed!
412INIT: Entering runlevel: 2
413[info] Using makefile-style concurrent boot in runlevel 2.
414[ ok ] Starting enhanced syslogd: rsyslogd.
415[ ok ] Starting system message bus: dbus.
416[ ok ] Starting NTP server: ntpd.
417Starting Hardware RNG entropy gatherer daemon: (Hardware RNG device inode not found)
418/etc/init.d/rng-tools: Cannot find a hardware RNG device to use.
419[ ok ] Starting OpenBSD Secure Shell server: sshd.
420[FAIL] startpar: service(s) returned failure: rng-tools ... failed!
421[ 35.816751] vcc3v0: disabling
422[ 35.819814] vcc5v0: disabling
423[ 35.823011] vddio-csi0: disabling
424[ 35.830667] vddio-csi1: disabling
425[ 35.834611] usb0-vbus: disabling