· 6 years ago · Sep 23, 2019, 05:26 AM
1Format: Log Type - Time(microsec) - Message - Optional Info
2Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
3S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.2.C2-00037
4S - IMAGE_VARIANT_STRING=DAASANAZA
5S - OEM_IMAGE_VERSION_STRING=administrator-p
6S - Boot Config, 0x000000e1
7B - 1566 - PBL, Start
8B - 4542 - bootable_media_detect_entry, Start
9B - 176045 - bootable_media_detect_success, Start
10B - 176050 - elf_loader_entry, Start
11B - 176666 - auth_hash_seg_entry, Start
12B - 176927 - auth_hash_seg_exit, Start
13B - 193012 - elf_segs_hash_verify_entry, Start
14B - 252122 - PBL, End
15B - 262147 - SBL1, Start
16B - 319884 - boot_flash_init, Start
17D - 30 - boot_flash_init, Delta
18B - 326441 - boot_config_data_table_init, Start
19D - 6862 - boot_config_data_table_init, Delta - (0 Bytes)
20B - 337879 - CDT version:3,Platform ID:8,Major ID:1,Minor ID:0,Subtype:0
21B - 343979 - pm_device_init, Start
22B - 347242 - pm_device_init, TEST - MSM8909 detected
23B - 352580 - pm_device_init, INFO - PM8909 is selected
24B - 366854 - PM_SET_VAL:Skip
25D - 21258 - pm_device_init, Delta
26B - 368257 - sbl1_ddr_set_params, Start
27B - 370636 - cpr_init, Start
28D - 30 - cpr_init, Delta
29B - 376278 - Pre_DDR_clock_init, Start
30D - 213 - Pre_DDR_clock_init, Delta
31D - 0 - sbl1_ddr_set_params, Delta
32B - 389271 - pm_driver_init, Start
33B - 395920 - --> Charge init
34B - 3867 - battery voltage
35B - 399397 - boot up
36B - 10 - Current status
37D - 10736 - pm_driver_init, Delta
38B - 411750 - clock_init, Start
39D - 152 - clock_init, Delta
40B - 412695 - Image Load, Start
41D - 26993 - QSEE Image Loaded, Delta - (490096 Bytes)
42B - 439749 - Image Load, Start
43D - 244 - SEC Image Loaded, Delta - (2048 Bytes)
44B - 447984 - sbl1_efs_handle_cookies, Start
45D - 671 - sbl1_efs_handle_cookies, Delta
46B - 454785 - Image Load, Start
47D - 14122 - RPM Image Loaded, Delta - (156564 Bytes)
48B - 468968 - Image Load, Start
49D - 19184 - APPSBL Image Loaded, Delta - (504368 Bytes)
50B - 488183 - QSEE Execution, Start
51D - 274 - QSEE Execution, Delta
52B - 493917 - SBL1, End
53D - 234057 - SBL1, Delta
54S - Throughput, 31000 KB/s (1153076 Bytes, 36929 us)
55S - DDR Frequency, 400 MHz
56Android Bootloader - UART_DM Initialized!!!
57[0] [0] welcome to lk
58
59[10] [10] platform_init()
60[10] [10] target_init()
61[50] [50] SDHC Running in HS200 mode
62[60] [60] Done initialization of the card
63[70] [70] pm8x41_get_is_cold_boot: cold boot
64[80] [80] Waiting for the RPM to populate smd channel table
65[80] [80] Not able to search the panel:
66[130] [130] Config MIPI_VIDEO_PANEL.
67[300] [300] Panic Lut0 0 Lut1 fff Robest 0
68[300] [300] ERROR: Splash image header invalid
69[330] [330] Turn on MIPI_VIDEO_PANEL.
70[350] [350] Video lane tested successfully
71CTRL+C: enter instruction mode
72CTRL+C: out instruction mode
73input FCT : enter instruction mode
74[1440] [1440] is_enter_fctmode ch: out fct instruction mode
75[1450] [1450] Recovery command: 32 normal1
76[1450] [1450] Unable to locate /bootselect partition
77[1460] [1460] boot_verifier: Device is in ORANGE boot state.
78[1460] [1460] Device is unlocked! Skipping verification...
79[1470] [1470] Loading boot image (16998400): start
80[1580] [1580] Loading boot image (16998400): done
81[1580] [1580] use_signed_kernel=1, is_unlocked=1, is_tampered=0.
82[1610] [1610] Best match DTB tags 245/00000008/0x00000000/0/1000d/0/0/0/90a4ab96/29315
83[1620] [1620] Using pmic info 0x1000d/0x0/0x0/0x0 for device 0x1010d/0x0/0x0/0x0
84[1620] [1620] cmdline: console=ttyHSL0,115200,n8 androidboot.console=ttyHSL0 androidboot.hardware=qcom msm_rtb.filter=0x237 ehci-hcd.park=3 androidboot.bootdevice=7824900.sdhci lpm_levels.sleep_disabled=1 earlyprintk buildvariant=userdebug androidboot.bootdevice=782490[1650] [1650] Updating device tree: start
85[1660] [1660] Updating device tree: done
86[1660] [1660] Channel alloc freed
87[1680] [1680] Turn off MIPI_VIDEO_PANEL.
88[1680] [1680] Continuous splash enabled, keeping panel alive.
89[1680] [1680] booting linux @ 0x80008000, ramdisk @ 0x82000000 (1350329), tags/device tree @ 0x81e00000
90[ 0.000000] Booting Linux on physical CPU 0x0
91[ 0.000000] Initializing cgroup subsys cpu
92[ 0.000000] Initializing cgroup subsys cpuacct
93[ 0.000000] Linux version 3.10.49 (front@front-quectel) (gcc version 4.8 (GCC) ) #25 SMP PREEMPT Sat Sep 21 14:10:29 CST 2019
94[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
95[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
96[ 0.000000] Machine: Qualcomm Technologies, Inc. MSM 8909 (Flattened Device Tree), model: Qualcomm Technologies, Inc. MSM8909-PM8909 1GB MTP
97[ 0.000000] cma: Found external_image__region@0, memory base 0x87a00000, size 6 MiB, limit 0xffffffff
98[ 0.000000] cma: Found modem_adsp_region@0, memory base 0x88000000, size 85 MiB, limit 0xffffffff
99[ 0.000000] cma: Found pheripheral_region@0, memory base 0x8d500000, size 7 MiB, limit 0xffffffff
100[ 0.000000] cma: Found venus_qseecom_region@0, memory base 0x00000000, size 6 MiB, limit 0x90000000
101[ 0.000000] cma: Found audio_region@0, memory base 0x00000000, size 3 MiB, limit 0xffffffff
102[ 0.000000] cma: Found splash_region@83000000, memory base 0x83000000, size 12 MiB, limit 0xffffffff
103[ 0.000000] cma: CMA: reserved 6 MiB at 0x87a00000 for external_image_mem
104[ 0.000000] cma: CMA: reserved 85 MiB at 0x88000000 for modem_adsp_mem
105[ 0.000000] cma: CMA: reserved 7 MiB at 0x8d500000 for peripheral_mem
106[ 0.000000] cma: CMA: reserved 8 MiB at 0x8f800000 for venus_qseecom_mem
107[ 0.000000] cma: CMA: reserved 4 MiB at 0xff800000 for audio_mem
108[ 0.000000] cma: CMA: reserved 12 MiB at 0x83000000 for cont_splash_mem
109[ 0.000000] cma: CMA: reserved 8 MiB at 0xaf000000 for default region
110[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
111[ 0.000000] PERCPU: Embedded 14 pages/cpu @c6c54000 s33472 r8192 d15680 u57344
112[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 494639
113[ 0.000000] Kernel command line: sched_enable_hmp=1 console=ttyHSL0,115200,n8 androidboot.console=ttyHSL0 androidboot.hardware=qcom msm_rtb.filter=0x237 ehci-hcd.park=3 androidboot.bootdevice=7824900.sdhci lpm_levels.sleep_disabled=1 earlyprintk buildvariant=userdebug androidboot.bootdevice=7824900.sdhci androidboot.serialno=3122bcdb androidboot.baseband=msm mdss_mdp3.panel=1:dsi:0:qcom,mdss_dsi_ili9881c_720p_video:1:none
114[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
115[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
116[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
117[ 0.000000] Memory: 1893768K/1996796K available (10542K kernel code, 1079K rwdata, 4660K rodata, 1420K init, 1349K bss, 103028K reserved, 1314812K highmem)
118[ 0.000000] Virtual kernel memory layout:
119[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
120[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
121[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
122[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
123[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
124[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
125[ 0.000000] .text : 0xc0008000 - 0xc0fd8b24 (16195 kB)
126[ 0.000000] .init : 0xc1000000 - 0xc11632c0 (1421 kB)
127[ 0.000000] .data : 0xc1164000 - 0xc1271e7c (1080 kB)
128[ 0.000000] .bss : 0xc1271f40 - 0xc13c34e4 (1350 kB)
129[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
130[ 0.000000] HMP scheduling enabled.
131[ 0.000000] Preemptible hierarchical RCU implementation.
132[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
133[ 0.000000] NR_IRQS:16 nr_irqs:16 16
134[ 0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
135[ 0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
136[ 0.000000] Switching to timer-based delay loop
137[ 0.000000] sched_clock: 32 bits at 19MHz, resolution 52ns, wraps every 223696213963ns
138[ 0.000000] Console: colour dummy device 80x30
139[ 0.000000] kmemleak: Kernel memory leak detector disabled
140[ 0.000846] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
141[ 0.000865] pid_max: default: 32768 minimum: 301
142[ 0.001223] Security Framework initialized
143[ 0.001266] SELinux: Initializing.
144[ 0.001551] Mount-cache hash table entries: 512
145[ 0.003211] Initializing cgroup subsys debug
146[ 0.003233] Initializing cgroup subsys freezer
147[ 0.003287] CPU: Testing write buffer coherency: ok
148[ 0.004130] /cpus/cpu@0 missing clock-frequency property
149[ 0.004152] /cpus/cpu@1 missing clock-frequency property
150[ 0.004171] /cpus/cpu@2 missing clock-frequency property
151[ 0.004192] /cpus/cpu@3 missing clock-frequency property
152[ 0.004208] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
153[ 0.004367] Setting up static identity map for 0xc0aba0f8 - 0xc0aba150
154[ 0.006427] ftrace: Allocated trace_printk buffers
155[ 0.033899] MSM Memory Dump base table set up
156[ 0.033987] MSM Memory Dump apps data table set up
157[ 0.034034] Configuring XPU violations to be fatal errors
158[ 0.043784] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
159[ 0.053654] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
160[ 0.063273] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
161[ 0.063571] Brought up 4 CPUs
162[ 0.063602] SMP: Total of 4 processors activated (153.60 BogoMIPS).
163[ 0.063612] CPU: All CPU(s) started in SVC mode.
164[ 0.085143] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
165[ 0.085179] ------------[ cut here ]------------
166[ 0.085206] WARNING: at /home/front/test01/SC20_Android7.1_R06_r00049.1/kernel/fs/proc/generic.c:102 __xlate_proc_name+0xa0/0xb4()
167[ 0.085216] name 'cpu/vfp_bounce'
168[ 0.085224] Modules linked in:
169[ 0.085242] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.49 #25
170[ 0.085273] [<c010be54>] (unwind_backtrace+0x0/0x11c) from [<c0109a04>] (show_stack+0x10/0x14)
171[ 0.085301] [<c0109a04>] (show_stack+0x10/0x14) from [<c0121784>] (warn_slowpath_common+0x4c/0x6c)
172[ 0.085327] [<c0121784>] (warn_slowpath_common+0x4c/0x6c) from [<c01217d0>] (warn_slowpath_fmt+0x2c/0x3c)
173[ 0.085352] [<c01217d0>] (warn_slowpath_fmt+0x2c/0x3c) from [<c024ba0c>] (__xlate_proc_name+0xa0/0xb4)
174[ 0.085375] [<c024ba0c>] (__xlate_proc_name+0xa0/0xb4) from [<c024ba6c>] (__proc_create+0x4c/0xf4)
175[ 0.085397] [<c024ba6c>] (__proc_create+0x4c/0xf4) from [<c024be50>] (proc_create_data+0x58/0x98)
176[ 0.085424] [<c024be50>] (proc_create_data+0x58/0x98) from [<c1002e34>] (vfp_init+0x16c/0x1d8)
177[ 0.085448] [<c1002e34>] (vfp_init+0x16c/0x1d8) from [<c0100670>] (do_one_initcall+0xb8/0x160)
178[ 0.085472] [<c0100670>] (do_one_initcall+0xb8/0x160) from [<c1000be4>] (kernel_init_freeable+0x10c/0x1d0)
179[ 0.085499] [<c1000be4>] (kernel_init_freeable+0x10c/0x1d0) from [<c0a9f3bc>] (kernel_init+0x8/0xe4)
180[ 0.085523] [<c0a9f3bc>] (kernel_init+0x8/0xe4) from [<c0105ff8>] (ret_from_fork+0x14/0x3c)
181[ 0.085573] ---[ end trace da227214a82491b7 ]---
182[ 0.085583] Failed to create procfs node for VFP bounce reporting
183[ 0.089045] pinctrl core: initialized pinctrl subsystem
184[ 0.089649] regulator-dummy: no parameters
185[ 0.105311] NET: Registered protocol family 16
186[ 0.119731] DMA: preallocated 256 KiB pool for atomic coherent allocations
187[ 0.182611] spmi_pmic_arb 200f000.qcom,spmi: PMIC Arb Version-2 0x20010000
188[ 0.191564] msm_watchdog b017000.qcom,wdt: wdog absent resource not present
189[ 0.191960] msm_watchdog b017000.qcom,wdt: MSM Watchdog Initialized
190[ 0.194427] cma: Assigned CMA region at 0 to 1de0000.qcom,venus device
191[ 0.199201] cma: Assigned CMA region at 0 to a21b000.qcom,pronto device
192[ 0.199578] cma: Assigned CMA region at 0 to 4080000.qcom,mss device
193[ 0.213310] KPI: Bootloader start count = 18567
194[ 0.213327] KPI: Bootloader end count = 74244
195[ 0.213337] KPI: Bootloader display count = 29673
196[ 0.213347] KPI: Bootloader load kernel count = 3596
197[ 0.213357] KPI: Kernel MPM timestamp = 171243
198[ 0.213366] KPI: Kernel MPM Clock frequency = 32768
199[ 0.213398] socinfo_print: v10, id=245, ver=2.0, raw_id=2400, raw_ver=1, hw_plat=8, hw_plat_ver=65536
200[ 0.213398] accessory_chip=0, hw_plat_subtype=0, pmic_model=65549, pmic_die_revision=65537 foundry_id=1 serial_number=270169395
201[ 0.215566] smd_channel_probe_worker: allocation table not initialized
202[ 0.215588] smd_channel_probe_worker: allocation table not initialized
203[ 0.222607] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
204[ 0.222624] hw-breakpoint: maximum watchpoint size is 8 bytes.
205[ 0.223248] msm_mpm_dev_probe(): Cannot get clk resource for XO
206[ 0.223283] platform 601d0.qcom,mpm: Driver mpm-v2 requests probe deferral
207[ 0.223850] msm-jtag-fuse 5e01c.jtagfuse: JTag Fuse initialized
208[ 0.225972] pm8909_s1_corner: 0 <--> 0 mV at 0 mV normal idle
209[ 0.226837] pm8909_s1_corner_ao: 0 <--> 0 mV at 0 mV normal idle
210[ 0.227666] pm8909_s1_floor_corner: 0 <--> 0 mV at 0 mV normal idle
211[ 0.228490] pm8909_s1_corner_so: 0 <--> 0 mV at 0 mV normal idle
212[ 0.229291] pm8909_s2: 1850 mV normal idle
213[ 0.230109] pm8909_l1: 1000 mV normal idle
214[ 0.231010] pm8909_l2: 1200 mV normal idle
215[ 0.231805] pm8909_l3: 500 <--> 1350 mV at 0 mV normal idle
216[ 0.232573] pm8909_l3_corner_ao: 0 <--> 0 mV at 0 mV normal idle
217[ 0.233306] pm8909_l3_corner_so: 0 <--> 0 mV at 0 mV normal idle
218[ 0.234072] pm8909_l4: 1800 mV normal idle
219[ 0.234932] pm8909_l5: 1800 mV normal idle
220[ 0.235821] pm8909_l6: 1800 mV normal idle
221[ 0.236621] pm8909_l7: 1800 mV normal idle
222[ 0.237374] pm8909_l7_ao: 1800 mV normal idle
223[ 0.238176] pm8909_l7_so: 1800 mV normal idle
224[ 0.239006] pm8909_l8: 2850 <--> 2900 mV at 2850 mV normal idle
225[ 0.239789] pm8909_l9: 3000 <--> 3300 mV at 3000 mV normal idle
226[ 0.240739] pm8909_l10: 1225 <--> 1300 mV at 1225 mV normal idle
227[ 0.241620] pm8909_l11: 1800 <--> 2950 mV at 1800 mV normal idle
228[ 0.242405] pm8909_l12: 1800 <--> 2950 mV at 1800 mV normal idle
229[ 0.243282] pm8909_l13: 3075 mV normal idle
230[ 0.244065] pm8909_l14: 1800 <--> 3000 mV at 1800 mV normal idle
231[ 0.245000] pm8909_l15: 1800 <--> 3000 mV at 1800 mV normal idle
232[ 0.245758] pm8909_l17: 2800 <--> 2850 mV at 2800 mV normal idle
233[ 0.246610] pm8909_l18: 2700 mV normal idle
234[ 0.248527] i2c-msm-v2 78b6000.i2c: probing driver i2c-msm-v2
235[ 0.248628] i2c-msm-v2 78b6000.i2c: error on clk_get(core_clk):-517
236[ 0.248647] i2c-msm-v2 78b6000.i2c: error probe() failed with err:-517
237[ 0.248686] platform 78b6000.i2c: Driver i2c-msm-v2 requests probe deferral
238[ 0.248954] i2c-msm-v2 78b8000.i2c: probing driver i2c-msm-v2
239[ 0.249028] i2c-msm-v2 78b8000.i2c: error on clk_get(core_clk):-517
240[ 0.249045] i2c-msm-v2 78b8000.i2c: error probe() failed with err:-517
241[ 0.249076] platform 78b8000.i2c: Driver i2c-msm-v2 requests probe deferral
242[ 0.249330] i2c-msm-v2 78b9000.i2c: probing driver i2c-msm-v2
243[ 0.249400] i2c-msm-v2 78b9000.i2c: error on clk_get(core_clk):-517
244[ 0.249418] i2c-msm-v2 78b9000.i2c: error probe() failed with err:-517
245[ 0.249448] platform 78b9000.i2c: Driver i2c-msm-v2 requests probe deferral
246[ 0.249699] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2
247[ 0.249770] i2c-msm-v2 78b7000.i2c: error on clk_get(core_clk):-517
248[ 0.249787] i2c-msm-v2 78b7000.i2c: error probe() failed with err:-517
249[ 0.249818] platform 78b7000.i2c: Driver i2c-msm-v2 requests probe deferral
250[ 0.250065] i2c-msm-v2 78b5000.i2c: probing driver i2c-msm-v2
251[ 0.250135] i2c-msm-v2 78b5000.i2c: error on clk_get(core_clk):-517
252[ 0.250152] i2c-msm-v2 78b5000.i2c: error probe() failed with err:-517
253[ 0.250184] platform 78b5000.i2c: Driver i2c-msm-v2 requests probe deferral
254[ 0.255468] sps:sps is ready.
255[ 0.267436] qcom,rpmcc-8909 1800000.qcom,rpmcc: Registered RPM clocks.
256[ 0.287180] qcom,gcc-8909 1800000.qcom,gcc: Registered GCC clocks
257[ 0.288385] clock-a7 b011050.qcom,clock-a7: Speed bin: 2 PVS Version: 0
258[ 0.290702] i2c-msm-v2 78b6000.i2c: probing driver i2c-msm-v2
259[ 0.290910] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
260[ 0.290929] i2c-msm-v2 78b6000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
261[ 0.292449] kworker/u8:2 (51) used greatest stack depth: 6892 bytes left
262[ 0.292601] kworker/u8:2 (50) used greatest stack depth: 6676 bytes left
263[ 0.293908] i2c-msm-v2 78b8000.i2c: probing driver i2c-msm-v2
264[ 0.294014] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
265[ 0.294031] i2c-msm-v2 78b8000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
266[ 0.294880] i2c-msm-v2 78b9000.i2c: probing driver i2c-msm-v2
267[ 0.294974] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
268[ 0.294991] i2c-msm-v2 78b9000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
269[ 0.297916] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2
270[ 0.298018] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
271[ 0.298034] i2c-msm-v2 78b7000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
272[ 0.301447] i2c-msm-v2 78b5000.i2c: probing driver i2c-msm-v2
273[ 0.301552] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
274[ 0.301569] i2c-msm-v2 78b5000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
275[ 0.352853] bio: create slab <bio-0> at 0
276[ 0.355228] spk_vreg: no parameters
277[ 0.356065] oem_otg_ext_vreg: no parameters
278[ 0.357867] SCSI subsystem initialized
279[ 0.358802] usbcore: registered new interface driver usbfs
280[ 0.358901] usbcore: registered new interface driver hub
281[ 0.359158] usbcore: registered new device driver usb
282[ 0.359341] media: Linux media interface: v0.10
283[ 0.359415] Linux video capture interface: v2.00
284[ 0.359677] BATTERY: batterydata_init: Battery-data device created!
285[ 0.361545] cma: Assigned CMA region at 0 to 1b.qcom,ion-heap device
286[ 0.361814] cma: Assigned CMA region at 0 to 1c.qcom,ion-heap device
287[ 0.362049] cma: Assigned CMA region at 0 to 1a.qcom,ion-heap device
288[ 0.362407] ION heap system created
289[ 0.362641] ION heap qsecom created at 0x8f800000 with size 600000
290[ 0.362668] ION heap audio created at 0xff800000 with size 314000
291[ 0.362691] ION heap pil_2 created at 0x88000000 with size 5500000
292[ 0.363165] msm_bus_fabric_init_driver
293[ 0.363442] msm_bus_device 580000.ad-hoc-bus: Dev 0
294[ 0.363465] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
295[ 0.363633] msm_bus_device 580000.ad-hoc-bus: msmbus_coresight initialized
296[ 0.363670] msm_bus_device 580000.ad-hoc-bus: Dev 4096
297[ 0.363689] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
298[ 0.363701] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
299[ 0.363870] msm_bus_device 580000.ad-hoc-bus: msmbus_coresight initialized
300[ 0.363905] msm_bus_device 580000.ad-hoc-bus: Dev 1024
301[ 0.363924] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
302[ 0.363936] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
303[ 0.364092] msm_bus_device 580000.ad-hoc-bus: msmbus_coresight initialized
304[ 0.364127] msm_bus_device 580000.ad-hoc-bus: Dev 2048
305[ 0.364146] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
306[ 0.364182] msm_bus_device 580000.ad-hoc-bus: Coresight support absent for bus: 2048
307[ 0.367074] msm_bus_init_clk: Valid node clk node 0 ctx 0
308[ 0.367084] msm_bus_init_clk: Valid node clk node 0 ctx 1msm_bus_init_clk: Valid node clk node 4096 ctx 0
309[ 0.367224] msm_bus_init_clk: Valid node clk node 4096 ctx 1msm_bus_init_clk: Valid node clk node 1024 ctx 0
310[ 0.367328] msm_bus_init_clk: Valid node clk node 1024 ctx 1msm_bus_init_clk: Valid Iface clk node 1024
311[ 0.367452] msm_bus_init_clk: Valid node clk node 2048 ctx 0msm_bus_init_clk: Valid node clk node 2048 ctx 1
312[ 0.381912] gdsc_venus: no parameters
313[ 0.382350] gdsc_mdss: no parameters
314[ 0.382831] gdsc_vfe: no parameters
315[ 0.383298] gdsc_oxili_gx: no parameters
316[ 0.383651] gdsc_venus_core0: fast normal
317[ 0.384675] mdss_pll_probe: MDSS pll label = MDSS DSI 0 PLL
318[ 0.385838] dsi_pll_clock_register_lpm: Registered DSI PLL clocks successfully
319[ 0.386879] msm_iommu 1f00000.qcom,iommu: device gfx_iommu (model: 500) mapped at f0320000, with 2 ctx banks
320[ 0.387774] msm_iommu 1e00000.qcom,iommu: device apps_iommu (model: 500) mapped at f0380000, with 22 ctx banks
321[ 0.394850] msm_iommu_ctx 1f09000.qcom,iommu-ctx: context gfx3d_user using bank 1
322[ 0.395051] msm_iommu_ctx 1f0a000.qcom,iommu-ctx: context gfx3d_priv using bank 2
323[ 0.395242] msm_iommu_ctx 1e22000.qcom,iommu-ctx: context MSA0_Audio using bank 2
324[ 0.395454] msm_iommu_ctx 1e23000.qcom,iommu-ctx: context vfe using bank 3
325[ 0.395639] msm_iommu_ctx 1e24000.qcom,iommu-ctx: context mdp_0 using bank 4
326[ 0.395824] msm_iommu_ctx 1e25000.qcom,iommu-ctx: context venus_ns using bank 5
327[ 0.396040] msm_iommu_ctx 1e27000.qcom,iommu-ctx: context mDSP using bank 7
328[ 0.396225] msm_iommu_ctx 1e28000.qcom,iommu-ctx: context gss using bank 8
329[ 0.396406] msm_iommu_ctx 1e29000.qcom,iommu-ctx: context a2 using bank 9
330[ 0.396654] msm_iommu_ctx 1e32000.qcom,iommu-ctx: context mdp_1 using bank 18
331[ 0.396918] msm_iommu_ctx 1e33000.qcom,iommu-ctx: context venus_sec_pixel using bank 19
332[ 0.397105] msm_iommu_ctx 1e34000.qcom,iommu-ctx: context venus_sec_bitstream using bank 20
333[ 0.397290] msm_iommu_ctx 1e35000.qcom,iommu-ctx: context venus_sec_non_pixel using bank 21
334[ 0.397545] msm_iommu_ctx 1e36000.qcom,iommu-ctx: context venus_fw using bank 22
335[ 0.397763] msm_iommu_ctx 1e37000.qcom,iommu-ctx: context periph_rpm using bank 23
336[ 0.397988] msm_iommu_ctx 1e38000.qcom,iommu-ctx: context periph_CE using bank 24
337[ 0.398174] msm_iommu_ctx 1e39000.qcom,iommu-ctx: context periph_BLSP using bank 25
338[ 0.398358] msm_iommu_ctx 1e3a000.qcom,iommu-ctx: context periph_SDC1 using bank 26
339[ 0.398540] msm_iommu_ctx 1e3b000.qcom,iommu-ctx: context periph_SDC2 using bank 27
340[ 0.398747] msm_iommu_ctx 1e3c000.qcom,iommu-ctx: context periph_audio using bank 28
341[ 0.398929] msm_iommu_ctx 1e3d000.qcom,iommu-ctx: context periph_USB_HS1 using bank 29
342[ 0.399110] msm_iommu_ctx 1e2a000.qcom,iommu-ctx: context qpic using bank 10
343[ 0.399320] msm_iommu_ctx 1e31000.qcom,iommu-ctx: context wlan using bank 17
344[ 0.399508] msm_iommu_ctx 1e3f000.qcom,iommu-ctx: context periph_CE_secure using bank 31
345[ 0.401248] Advanced Linux Sound Architecture Driver Initialized.
346[ 0.402079] Bluetooth: ee855f10
347[ 0.402139] NET: Registered protocol family 31
348[ 0.402149] Bluetooth: ee855f10
349[ 0.402166] Bluetooth: ee855f08Bluetooth: ee855ef8
350[ 0.402263] Bluetooth: ee855f00[ 0.402709] cfg80211: Calling CRDA to update world regulatory domain
351[ 0.402747] cfg80211: World regulatory domain updated:
352[ 0.402756] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
353[ 0.402766] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
354[ 0.402775] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
355[ 0.402785] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
356[ 0.402794] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
357[ 0.402804] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
358[ 0.402813] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
359[ 0.402822] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
360[ 0.402831] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
361[ 0.403896] Switching to clocksource arch_sys_counter
362[ 0.467441] NET: Registered protocol family 2
363[ 0.468333] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
364[ 0.468961] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
365[ 0.469136] TCP: Hash tables configured (established 8192 bind 8192)
366[ 0.469324] TCP: reno registered
367[ 0.469408] UDP hash table entries: 512 (order: 2, 24576 bytes)
368[ 0.469510] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
369[ 0.469955] NET: Registered protocol family 1
370[ 0.470936] gcc-mdss-8909 qcom,gcc-mdss.31: Registered GCC MDSS clocks.
371[ 0.471643] Trying to unpack rootfs image as initramfs...
372[ 0.563589] Freeing initrd memory: 1316K (c2000000 - c2149000)
373[ 0.566730] hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
374[ 0.570950] Initialise module verification
375[ 0.571026] audit: initializing netlink socket (disabled)
376[ 0.571113] type=2000 audit(0.559:1): initialized
377[ 0.792612] bounce pool size: 64 pages
378[ 0.803684] fuse init (API version 7.23)
379[ 0.809173] Key type asymmetric registered
380[ 0.809187] Asymmetric key parser 'x509' registered
381[ 0.809488] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
382[ 0.809500] io scheduler noop registered
383[ 0.809508] io scheduler deadline registered
384[ 0.809541] io scheduler row registered
385[ 0.809782] io scheduler cfq registered (default)
386[ 0.813846] platform qcom,smp2pgpio-ssr-smp2p-4-in.14: Driver smp2pgpio requests probe deferral
387[ 0.814189] platform qcom,smp2pgpio-ssr-smp2p-4-out.15: Driver smp2pgpio requests probe deferral
388[ 0.814450] platform qcom,smp2pgpio-ssr-smp2p-1-in.16: Driver smp2pgpio requests probe deferral
389[ 0.814747] platform qcom,smp2pgpio-ssr-smp2p-1-out.17: Driver smp2pgpio requests probe deferral
390[ 0.818348] mdss_dsi_ctrl_probe: DSI Ctrl name = MDSS DSI CTRL->0
391[ 0.818703] mdss_dsi_panel_init: Panel Name = ili9881c 720p video mode dsi panel
392[ 0.819120] mdss_dsi_parse_dcs_cmds: failed, key=qcom,mdss-dsi-post-panel-on-command
393[ 0.819144] mdss_dsi_parse_dcs_cmds: failed, key=qcom,mdss-dsi-panel-status-command
394[ 0.819186] mdss_dsi_parse_panel_features: ulps feature disabled
395[ 0.819201] mdss_dsi_parse_panel_features: ulps during suspend feature disabled
396[ 0.819213] mdss_dsi_parse_panel_features: dynamic switch feature enabled: 0
397[ 0.819238] mdss_dsi_parse_panel_features:1207, Disp_en gpio not specified
398[ 0.819259] mdss_dsi_panel_init: Continuous splash enabled
399[ 0.819743] dsi_panel_device_register:1875, TE gpio not specified
400[ 0.819760] dsi_panel_device_register: bklt_en gpio not specified
401[ 0.819891] mdss_dsi_pll_1_clk_init: can't find vco_clk. rc=-517
402[ 0.819898] PLL 1 Clock's did not register
403[ 0.819927] mdss_dsi_retrieve_ctrl_resources: ctrl_base=f00fc000 ctrl_size=25c phy_base=f00fe500 phy_size=2b0
404[ 0.819941] dsi_panel_device_register: Using default BTA for ESD check
405[ 0.834933] mdss_register_panel: adding framebuffer device 1ac8000.qcom,mdss_dsi
406[ 0.837352] mdss_dsi_status_init: DSI status check interval:5000
407[ 0.838819] mdp3_alloc: allocating 12582912 bytes at c3000000 (83000000 phys) for fb 0
408[ 0.839195] mdss_fb_register: FrameBuffer[0] 720x1280 registered successfully!
409[ 0.839204] mdp3_ctrl_init: mdp3_ctrl_init
410[ 0.839313] mdp3 1a00000.qcom,mdss_mdp: Unbalanced pm_runtime_enable!
411[ 0.842187] IPC_RTR: msm_ipc_router_smd_driver_register Already driver registered IPCRTR
412[ 0.844733] msm_rpm_log_probe: OK
413[ 0.849001] NET: Registered protocol family 27
414[ 0.854124] In memshare_probe, Memshare probe success
415[ 0.856398] subsys-pil-tz a21b000.qcom,pronto: [wcnss]: Error getting proxy unvoting gpio
416[ 0.856426] platform a21b000.qcom,pronto: Driver subsys-pil-tz requests probe deferral
417[ 0.858300] pil-q6v5-mss 4080000.qcom,mss: [modem]: Error getting proxy unvoting gpio
418[ 0.858503] platform 4080000.qcom,mss: Driver pil-q6v5-mss requests probe deferral
419[ 0.859921] msm_serial_hsl_probe: detected port #0 (ttyHSL0)
420[ 0.859964] AXI: get_pdata(): Error: Client name not found
421[ 0.859973] AXI: msm_bus_cl_get_pdata(): client has to provide missing entry for successful registration
422[ 0.859980] msm_serial_hsl_probe: Bus scaling is disabled
423[ 0.860131] 78af000.serial: ttyHSL0 at MMIO 0x78af000 (irq = 139) is a MSM
424[ 0.860193] msm_hsl_console_setup: console setup on port #0
425[ 2.244034] msm_thermal:do_freq_control Limiting CPU0 max frequency to 800000. Temp:60
426[ 2.244145] msm_thermal:do_freq_control Limiting CPU1 max frequency to 800000. Temp:60
427[ 2.244165] msm_thermal:do_freq_control Limiting CPU2 max frequency to 800000. Temp:60
428[ 2.244184] msm_thermal:do_freq_control Limiting CPU3 max frequency to 800000. Temp:60
429[ 3.058181] console [ttyHSL0] enabled
430[ 3.062276] msm_serial_hsl_probe: detected port #1 (ttyHSL1)
431[ 3.067522] AXI: get_pdata(): Error: Client name not found
432[ 3.072890] AXI: msm_bus_cl_get_pdata(): client has to provide missing entry for successful registration
433[ 3.082398] msm_serial_hsl_probe: Bus scaling is disabled
434[ 3.087912] 78b0000.serial: ttyHSL1 at MMIO 0x78b0000 (irq = 140) is a MSM
435[ 3.095378] msm_serial_hsl_init: driver initialized
436[ 3.117038] kgsl kgsl-3d0: Initialized kgsl-3d0: mmu=on
437[ 3.138570] brd: module loaded
438[ 3.146510] loop: module loaded
439[ 3.149592] apds993x 1-0039: Unable to read cross_talk use default 100
440[ 3.294494] i2c-msm-v2 78b5000.i2c: msm_bus_scale_register_client(mstr-id:86):0x5 (ok)
441[ 3.302260] i2c-msm-v2 78b5000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x39 MSTR_STS:0x011363c8 OPER:0x00000010
442[ 3.317173] apds993x 1-0039: Neither APDS993x nor APDS990x
443[ 3.322555] apds993x 1-0039: Not a valid chip ID
444[ 3.328321] QSEECOM: qseecom_probe: qseecom.qsee_version = 0x405000
445[ 3.333640] QSEECOM: qseecom_probe: disk-encrypt-pipe-pair=0x2
446[ 3.339324] QSEECOM: qseecom_probe: Device does not support PFEQSEECOM: qseecom_probe: qsee-ce-hw-instance=0x0
447[ 3.349179] QSEECOM: qseecom_probe: qseecom.appsbl_qseecom_support = 0x0[ 3.355906] QSEECOM: qseecom_probe: qseecom clocks handled by other subsystem
448[ 3.363125] QSEECOM: qseecom_probe: secure app region addr=0x87a00000 size=0x200000
449[ 3.373893] i2c-core: driver [tabla-i2c-core] using legacy suspend method
450[ 3.379881] i2c-core: driver [tabla-i2c-core] using legacy resume method
451[ 3.386792] i2c-core: driver [wcd9xxx-i2c-core] using legacy suspend method
452[ 3.393438] i2c-core: driver [wcd9xxx-i2c-core] using legacy resume method
453[ 3.400623] i2c-core: driver [tasha-i2c-core] using legacy suspend method
454[ 3.407184] i2c-core: driver [tasha-i2c-core] using legacy resume method
455[ 3.415131] SCSI Media Changer driver v0.25
456[ 3.422917] tun: Universal TUN/TAP device driver, 1.6
457[ 3.427063] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
458[ 3.437305] PPP generic driver version 2.4.2
459[ 3.440756] PPP BSD Compression module registered
460[ 3.445279] PPP Deflate Compression module registered
461[ 3.450276] PPP MPPE Compression module registered
462[ 3.455133] NET: Registered protocol family 24
463[ 3.460690] wcnss_wlan probed in built-in mode
464[ 3.468790] usbcore: registered new interface driver asix
465[ 3.473249] usbcore: registered new interface driver ax88179_178a
466[ 3.479407] usbcore: registered new interface driver cdc_ether
467[ 3.485216] usbcore: registered new interface driver net1080
468[ 3.490760] usbcore: registered new interface driver cdc_subset
469[ 3.496717] usbcore: registered new interface driver zaurus
470[ 3.502564] usbcore: registered new interface driver cdc_ncm
471[ 3.508839] msm_sharedmem: sharedmem_register_qmi: qmi init successful
472[ 3.514971] msm_sharedmem: msm_sharedmem_probe: Device created for client 'rmtfs'
473[ 3.522097] msm_sharedmem: msm_sharedmem_probe: Device created for client 'rfsa_dsp'
474[ 3.529835] msm_sharedmem: msm_sharedmem_probe: Device created for client 'rfsa_mdm'
475[ 3.538062] msm_otg 78d9000.usb: msm_otg probe
476[ 3.546548] msm_otg 78d9000.usb: OTG regs = f01f4000
477[ 3.554025] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
478[ 3.559515] ehci-msm: Qualcomm On-Chip EHCI Host Controller
479[ 3.565877] ehci-msm2: Qualcomm EHCI Host Controller
480[ 3.570768] usbcore: registered new interface driver cdc_acm
481[ 3.575733] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
482[ 3.583755] usbcore: registered new interface driver ccid_bridge
483[ 3.589936] ccid_bridge_init: success
484[ 3.593381] usbcore: registered new interface driver usb-storage
485[ 3.599389] usbcore: registered new interface driver ums-alauda
486[ 3.605282] usbcore: registered new interface driver ums-cypress
487[ 3.611221] usbcore: registered new interface driver ums-datafab
488[ 3.617298] usbcore: registered new interface driver ums-freecom
489[ 3.623201] usbcore: registered new interface driver ums-isd200
490[ 3.629158] usbcore: registered new interface driver ums-jumpshot
491[ 3.635230] usbcore: registered new interface driver ums-karma
492[ 3.641032] usbcore: registered new interface driver ums-onetouch
493[ 3.647127] usbcore: registered new interface driver ums-sddr09
494[ 3.652977] usbcore: registered new interface driver ums-sddr55
495[ 3.658930] usbcore: registered new interface driver ums-usbat
496[ 3.664900] usbcore: registered new interface driver usbserial
497[ 3.670512] usbcore: registered new interface driver qc_csvt
498[ 3.676208] usbserial: USB Serial support registered for qc_csvt
499[ 3.682159] usbcore: registered new interface driver usb_ehset_test
500[ 3.690967] msm_otg 78d9000.usb: phy_reset: success
501[ 3.692093] mousedev: PS/2 mouse device common for all mice
502[ 3.692360] usbcore: registered new interface driver xpad
503[ 3.694588] Goodix-TS 5-005d: Regulator get failed avdd ret=-19
504[ 3.694604] Goodix-TS 5-005d: Regulator get failed vdd ret=-19
505[ 3.695603] Goodix-TS 5-005d: Can not lookup pmx_ts_release pinstate -19
506[ 3.814442] i2c-msm-v2 78b9000.i2c: msm_bus_scale_register_client(mstr-id:86):0x8 (ok)
507[ 3.821866] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:4) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000090
508[ 3.837495] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:4) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000090
509[ 3.853038] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:4) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000090
510[ 3.868689] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:4) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000090
511[ 3.884398] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:4) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000090
512[ 3.899943] Goodix-TS 5-005d: init external watchdog failed!
513[ 3.905747] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
514[ 3.921301] Goodix-TS 5-005d: I2C retry: 1
515[ 3.925531] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
516[ 3.941090] Goodix-TS 5-005d: I2C retry: 2
517[ 3.945322] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
518[ 3.960880] Goodix-TS 5-005d: I2C retry: 3
519[ 3.965113] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
520[ 3.980672] Goodix-TS 5-005d: I2C retry: 4
521[ 3.984907] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
522[ 4.000462] Goodix-TS 5-005d: I2C retry: 5
523[ 4.004539] Goodix-TS 5-005d: gtp_reset_guitar exit init_done=0:
524[ 4.010475] Goodix-TS 5-005d: GTP i2c test failed time 4.
525[ 4.044196] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
526[ 4.058946] Goodix-TS 5-005d: I2C retry: 1
527[ 4.063137] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
528[ 4.078738] Goodix-TS 5-005d: I2C retry: 2
529[ 4.082929] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
530[ 4.098526] Goodix-TS 5-005d: I2C retry: 3
531[ 4.102719] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
532[ 4.118317] Goodix-TS 5-005d: I2C retry: 4
533[ 4.122511] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
534[ 4.138109] Goodix-TS 5-005d: I2C retry: 5
535[ 4.142137] Goodix-TS 5-005d: gtp_reset_guitar exit init_done=0:
536[ 4.148216] Goodix-TS 5-005d: GTP i2c test failed time 3.
537[ 4.174191] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
538[ 4.188936] Goodix-TS 5-005d: I2C retry: 1
539[ 4.193129] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
540[ 4.208728] Goodix-TS 5-005d: I2C retry: 2
541[ 4.212921] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
542[ 4.228521] Goodix-TS 5-005d: I2C retry: 3
543[ 4.232712] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
544[ 4.248310] Goodix-TS 5-005d: I2C retry: 4
545[ 4.252505] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
546[ 4.268104] Goodix-TS 5-005d: I2C retry: 5
547[ 4.272129] Goodix-TS 5-005d: gtp_reset_guitar exit init_done=0:
548[ 4.278163] Goodix-TS 5-005d: GTP i2c test failed time 2.
549[ 4.304185] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
550[ 4.318931] Goodix-TS 5-005d: I2C retry: 1
551[ 4.323124] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
552[ 4.338723] Goodix-TS 5-005d: I2C retry: 2
553[ 4.342916] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
554[ 4.358514] Goodix-TS 5-005d: I2C retry: 3
555[ 4.362708] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
556[ 4.378305] Goodix-TS 5-005d: I2C retry: 4
557[ 4.382498] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
558[ 4.398098] Goodix-TS 5-005d: I2C retry: 5
559[ 4.402125] Goodix-TS 5-005d: gtp_reset_guitar exit init_done=0:
560[ 4.408159] Goodix-TS 5-005d: GTP i2c test failed time 1.
561[ 4.434189] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
562[ 4.448934] Goodix-TS 5-005d: I2C retry: 1
563[ 4.453129] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
564[ 4.468726] Goodix-TS 5-005d: I2C retry: 2
565[ 4.472920] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
566[ 4.488518] Goodix-TS 5-005d: I2C retry: 3
567[ 4.492710] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
568[ 4.508310] Goodix-TS 5-005d: I2C retry: 4
569[ 4.512503] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:2) mode:FIFO slv_addr:0x5d MSTR_STS:0x011363c8 OPER:0x00000010
570[ 4.528101] Goodix-TS 5-005d: I2C retry: 5
571[ 4.532127] Goodix-TS 5-005d: gtp_reset_guitar exit init_done=0:
572[ 4.538162] Goodix-TS 5-005d: GTP i2c test failed time 0.
573[ 4.564021] Goodix-TS 5-005d: I2C communication ERROR!
574[ 4.568330] Goodix-TS: probe of 5-005d failed with error -107
575[ 4.574620] <<GTP-INF>>[gt1x_ts_probe:626] GTP Driver Version: V1.4<2015/07/10>
576[ 4.581143] <<GTP-INF>>[gt1x_ts_probe:627] GTP I2C Address: 0x14
577[ 4.587276] <<GTP-ERR>>[gt1x_parse_dt:331] regulator get of vdd_ana failed
578[ 4.594567] Goodix-TP 5-0014: Can not lookup pmx_ts_release pinstate -19
579[ 4.600701] <<GTP-INF>>[gt1x_reset_guitar:815] GTP RESET!
580[ 4.724200] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:5) mode:FIFO slv_addr:0x14 MSTR_STS:0x011363c8 OPER:0x00000090
581[ 4.738949] <<GTP-ERR>>[_do_i2c_write:433] I2c transfer error! (-107)
582[ 4.745443] <<GTP-ERR>>[gt1x_init:2353] Reset guitar failed!
583[ 4.750956] <<GTP-INF>>[gt1x_reset_guitar:815] GTP RESET!
584[ 4.874189] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:5) mode:FIFO slv_addr:0x14 MSTR_STS:0x011363c8 OPER:0x00000090
585[ 4.888931] <<GTP-ERR>>[_do_i2c_write:433] I2c transfer error! (-107)
586[ 4.895342] <<GTP-ERR>>[gt1x_init:2353] Reset guitar failed!
587[ 4.900944] <<GTP-INF>>[gt1x_reset_guitar:815] GTP RESET!
588[ 5.024190] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:5) mode:FIFO slv_addr:0x14 MSTR_STS:0x011363c8 OPER:0x00000090
589[ 5.038931] <<GTP-ERR>>[_do_i2c_write:433] I2c transfer error! (-107)
590[ 5.045347] <<GTP-ERR>>[gt1x_init:2353] Reset guitar failed!
591[ 5.050943] <<GTP-INF>>[gt1x_reset_guitar:815] GTP RESET!
592[ 5.174195] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:5) mode:FIFO slv_addr:0x14 MSTR_STS:0x011363c8 OPER:0x00000090
593[ 5.188940] <<GTP-ERR>>[_do_i2c_write:433] I2c transfer error! (-107)
594[ 5.195351] <<GTP-ERR>>[gt1x_init:2353] Reset guitar failed!
595[ 5.200949] <<GTP-INF>>[gt1x_reset_guitar:815] GTP RESET!
596[ 5.324189] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:5) mode:FIFO slv_addr:0x14 MSTR_STS:0x011363c8 OPER:0x00000090
597[ 5.338930] <<GTP-ERR>>[_do_i2c_write:433] I2c transfer error! (-107)
598[ 5.345344] <<GTP-ERR>>[gt1x_init:2353] Reset guitar failed!
599[ 5.350944] <<GTP-ERR>>[gt1x_init:2379] Init failed, use default setting
600[ 5.357841] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:4 tx:2) mode:FIFO slv_addr:0x14 MSTR_STS:0x011363c8 OPER:0x00000010
601[ 5.373395] <<GTP-ERR>>[_do_i2c_read:391] I2c Transfer error! (-107)
602[ 5.379721] <<GTP-ERR>>[gt1x_get_chip_type:922] I2c communication error.
603[ 5.386398] <<GTP-ERR>>[gt1x_init:2389] Get chip type failed!
604[ 5.392102] <<GTP-ERR>>[gt1x_ts_probe:664] gt1x_init() failed.
605[ 5.398011] Goodix-TP: probe of 5-0014 failed with error -1
606[ 5.404266] [FTS_TS/I]fts_ts_probe:Touch Screen(I2C BUS) driver prboe...
607[ 5.410155] [FTS_TS/I]fts_get_dt_coords:display x(0 720) y(0 1280)
608[ 5.416377] [FTS_TS/I]fts_parse_dt:VK Number:3, key:(139,172,158), coords:(150,1340),(330,1340),(660,1340)
609[ 5.426054] [FTS_TS/I]fts_parse_dt:max touch number:5, irq gpio:924, reset gpio:923
610[ 5.433852] [FTS_TS/I]fts_input_init:set key capabilities
611[ 5.439356] input: fts_ts as /devices/soc.0/78b9000.i2c/i2c-5/5-0038/input/input0
612[ 5.714210] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
613[ 5.728967] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
614[ 5.735028] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
615[ 5.750575] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
616[ 5.756640] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
617[ 5.772192] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
618[ 5.778256] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
619[ 5.793807] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
620[ 5.799866] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
621[ 5.815421] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
622[ 5.821434] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
623[ 5.837034] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
624[ 6.044229] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
625[ 6.058980] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
626[ 6.065037] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
627[ 6.080594] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
628[ 6.086654] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
629[ 6.102209] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
630[ 6.108311] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
631[ 6.123886] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
632[ 6.129884] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
633[ 6.145440] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
634[ 6.151451] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
635[ 6.167052] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
636[ 6.374196] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
637[ 6.388947] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
638[ 6.395006] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
639[ 6.410560] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
640[ 6.416621] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
641[ 6.432176] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
642[ 6.438237] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
643[ 6.453791] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
644[ 6.459850] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
645[ 6.475411] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
646[ 6.481418] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
647[ 6.497016] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
648[ 6.704197] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
649[ 6.718947] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
650[ 6.725006] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
651[ 6.740564] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
652[ 6.746619] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
653[ 6.762178] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
654[ 6.768238] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
655[ 6.783792] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
656[ 6.789851] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
657[ 6.805406] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
658[ 6.811421] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
659[ 6.827022] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
660[ 7.034227] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
661[ 7.048978] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
662[ 7.055037] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
663[ 7.070593] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
664[ 7.076653] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
665[ 7.092206] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
666[ 7.098267] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
667[ 7.113821] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
668[ 7.119881] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
669[ 7.135435] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
670[ 7.141450] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000010
671[ 7.157051] [FTS_TS/E]fts_read:i2c_transfer(read) fail,ret:-107
672[ 7.364021] [FTS_TS/I]fts_get_ic_information:fw is invalid, need read boot id
673[ 7.370291] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000090
674[ 7.385889] [FTS_TS/E]fts_write:i2c_transfer(write) fail,reg:-107
675[ 7.392075] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000090
676[ 7.407678] [FTS_TS/E]fts_write:i2c_transfer(write) fail,reg:-107
677[ 7.413862] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000090
678[ 7.429465] [FTS_TS/E]fts_write:i2c_transfer(write) fail,reg:-107
679[ 7.435528] [FTS_TS/E]fts_hid2std:hid2std cmd write fail
680[ 7.440949] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000090
681[ 7.456550] [FTS_TS/E]fts_write:i2c_transfer(write) fail,reg:-107
682[ 7.462732] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000090
683[ 7.478336] [FTS_TS/E]fts_write:i2c_transfer(write) fail,reg:-107
684[ 7.484568] i2c-msm-v2 78b9000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x38 MSTR_STS:0x011363c8 OPER:0x00000090
685[ 7.500128] [FTS_TS/E]fts_write:i2c_transfer(write) fail,reg:-107
686[ 7.506187] [FTS_TS/E]fts_read_bootid:start cmd write fail
687[ 7.511608] [FTS_TS/E]fts_get_ic_information:read boot id fail
688[ 7.517466] [FTS_TS/E]fts_ts_probe_entry:not focal IC, unregister driver
689[ 7.954515] [FTS_TS/E]fts_ts_probe:Touch Screen(I2C BUS) driver probe fail
690[ 7.960402] fts_ts: probe of 5-0038 failed with error -107
691[ 7.987238] i2c-msm-v2 78b5000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x30 MSTR_STS:0x011363c8 OPER:0x00000010
692[ 8.002005] mmc3416x 1-0030: read reg 6 failed.(-107)
693[ 8.007062] mmc3416x 1-0030: Check device failed
694[ 8.011790] mmc3416x: probe of 1-0030 failed with error -107
695[ 8.017408] stk3x1x_probe: driver version = 3.4.4ts
696[ 8.022151] stk_ps 1-0048: stk3x1x_probe: stk3x1x_parse_dt ret=0
697[ 8.028516] input: stk3x1x-ls as /devices/soc.0/78b5000.i2c/i2c-1/1-0048/input/input1
698[ 8.036389] input: proximity as /devices/soc.0/78b5000.i2c/i2c-1/1-0048/input/input2
699[ 8.046177] mpu6050 1-0068: Regulator get failed vi2c ret=-19
700[ 8.154255] i2c-msm-v2 78b5000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x68 MSTR_STS:0x011363c8 OPER:0x00000010
701[ 8.169036] mpu6050 1-0068: Fail to read power mode, ret=-107
702[ 8.174730] mpu6050 1-0068: Cannot get invalid chip type
703[ 8.180151] mpu6050 1-0068: Probe device return error-107
704[ 8.185438] mpu6050: probe of 1-0068 failed with error -107
705[ 8.190980] AKM compass driver: initialize.
706[ 8.284225] i2c-msm-v2 78b5000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0xc MSTR_STS:0x011363c8 OPER:0x00000090
707[ 8.298909] akm8963 1-000c: akm_i2c_txdata: transfer failed.
708[ 8.304580] akm8963 1-000c: AKECS_Set_PowerDown: Can not set to powerdown mode.
709[ 8.311958] i2c-msm-v2 78b5000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:2 tx:1) mode:FIFO slv_addr:0xc MSTR_STS:0x011363c8 OPER:0x00000010
710[ 8.327464] akm8963 1-000c: akm_i2c_rxdata: transfer failed.
711[ 8.333202] akm8963: probe of 1-000c failed with error -107
712[ 8.338704] AKM compass driver: initialize.
713[ 8.342872] i2c-core: driver [bma2x2-accel] using legacy suspend method
714[ 8.349399] i2c-core: driver [bma2x2-accel] using legacy resume method
715[ 8.356175] i2c-core: driver [bmi160] using legacy suspend method
716[ 8.361935] i2c-core: driver [bmi160] using legacy resume method
717[ 8.369282] qcom,qpnp-rtc qpnp-rtc-6: rtc core: registered qpnp_rtc as rtc0
718[ 8.375672] i2c /dev entries driver
719[ 8.384556] platform 1d00000.qcom,vidc: Driver msm_vidc_v4l2 requests probe deferral
720[ 8.396160] msm_actuator_i2c_probe:1313 msm_actuator_i2c_probe: succeeded
721[ 8.402572] LED trigger flashlight-trigger failed to register (-17)
722[ 8.409512] adp1660 i2c_add_driver success
723[ 8.412963] msm_flash_init_module:1114 Enter
724[ 8.417518] msm_flash_lm3642_init entry
725[ 8.422210] msm_eeprom_parse_memory_map: pageen not needed
726[ 8.426820] msm_eeprom_parse_memory_map: pageen not needed
727[ 8.432143] msm_eeprom_parse_memory_map: pageen not needed
728[ 8.469234] i2c-msm-v2 78b7000.i2c: msm_bus_scale_register_client(mstr-id:86):0x9 (ok)
729[ 8.476704] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x36 MSTR_STS:0x0d1300c8 OPER:0x00000090
730[ 8.504061] read_eeprom_memory: page write failed
731[ 8.507727] msm_eeprom_i2c_probe read_eeprom_memory failed
732[ 8.544181] msm_eeprom_i2c_probe failed! rc = -107
733[ 8.547949] msm_eeprom: probe of 3-006c failed with error -107
734[ 8.556557] g_sctrl[0] ed8ba800
735[ 8.559071] g_sctrl[1] ed8bb000[ 8.561679] gc0310_init_module:487
736[ 8.570203] BMS: bms_get_adc: vadc not found - defer probe rc=-517
737[ 8.575429] BMS: qpnp_vm_bms_probe: Failed to get adc rc=-517
738[ 8.581100] spmi qpnp-vm-bms-10: Driver qcom,qpnp-vm-bms requests probe deferral
739[ 8.588799] CHG: qpnp_lbc_main_probe: Failed to read DT properties rc=-517
740[ 8.595428] spmi qpnp-linear-charger-8: Driver qcom,qpnp-linear-charger requests probe deferral
741[ 8.604895] unable to find DT imem DLOAD mode node
742[ 8.609172] unable to find DT imem EDLOAD mode node
743[ 8.615414] qpnp_vadc_get_temp: VADC read error with -517
744[ 8.619781] thermal thermal_zone0: failed to read out thermal zone 0
745[ 8.626581] qpnp_vadc_get_temp: VADC read error with -517
746[ 8.631500] thermal thermal_zone1: failed to read out thermal zone 1
747[ 8.638169] qpnp_vadc_get_temp: VADC read error with -517
748[ 8.643217] thermal thermal_zone2: failed to read out thermal zone 2
749[ 8.669878] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
750[ 8.677596] device-mapper: req-crypt: dm-req-crypt successfully initalized.
751[ 8.677596]
752[ 8.686275] cpuidle: using governor ladder
753[ 8.689781] cpuidle: using governor menu
754[ 8.693741] sdhci: Secure Digital Host Controller Interface driver
755[ 8.699901] sdhci: Copyright(c) Pierre Ossman
756[ 8.704227] sdhci-pltfm: SDHCI platform and OF driver helper
757[ 8.718426] sdhci_msm 7824900.sdhci: host_use_default_qos = 1
758[ 8.723143] sdhci_msm 7824900.sdhci: For qos_policy(default qos) = 0, tbl_sz = 3, qos type = 2
759[ 8.731786] sdhci_msm 7824900.sdhci: dma_latency = 2
760[ 8.736812] sdhci_msm 7824900.sdhci: dma_latency = 241
761[ 8.741976] sdhci_msm 7824900.sdhci: dma_latency = 501
762[ 8.747229] sdhci_msm 7824900.sdhci: For qos_policy(modified dynamic qos) = 1, tbl_sz = 1, qos type = 2
763[ 8.756602] sdhci_msm 7824900.sdhci: dma_latency = 200
764[ 8.761770] sdhci_msm 7824900.sdhci: For qos_policy(modified dynamic qos) = 2, tbl_sz = 1, qos type = 2
765[ 8.771183] sdhci_msm 7824900.sdhci: dma_latency = 200
766[ 8.776392] sdhci_msm 7824900.sdhci: Host using default pm_qos
767[ 8.783726] mmc0: no vqmmc regulator found
768[ 8.786859] mmc0: no vmmc regulator found
769[ 8.820660] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using 32-bit ADMA
770[ 8.836089] sdhci_msm 7864900.sdhci: host_use_default_qos = 1
771[ 8.840805] sdhci_msm 7864900.sdhci: For qos_policy(default qos) = 0, tbl_sz = 3, qos type = 2
772[ 8.849447] sdhci_msm 7864900.sdhci: dma_latency = 2
773[ 8.854472] sdhci_msm 7864900.sdhci: dma_latency = 241
774[ 8.859643] sdhci_msm 7864900.sdhci: dma_latency = 501
775[ 8.865049] sdhci_msm 7864900.sdhci: For qos_policy(modified dynamic qos) = 1, tbl_sz = 1, qos type = 2
776[ 8.874418] sdhci_msm 7864900.sdhci: dma_latency = 200
777[ 8.879469] sdhci_msm 7864900.sdhci: For qos_policy(modified dynamic qos) = 2, tbl_sz = 1, qos type = 2
778[ 8.889006] sdhci_msm 7864900.sdhci: dma_latency = 200
779[ 8.894209] sdhci_msm 7864900.sdhci: Host using default pm_qos
780[ 8.902411] mmc1: no vqmmc regulator found
781[ 8.905697] mmc1: no vmmc regulator found
782[ 8.939952] mmc1: SDHCI controller on 7864900.sdhci [7864900.sdhci] using 32-bit ADMA
783[ 8.947395] qcom,leds-qpnp: probe of leds-qpnp-7 failed with error -10
784[ 8.967282] mmc0: BKOPS_EN bit = 0
785[ 8.972474] qce 720000.qcedev: Qualcomm Crypto 5.3.1 device found @0x720000
786[ 8.978472] qce 720000.qcedev: CE device = 0x0
787[ 8.978472] , IO base, CE = 0xf0680000
788[ 8.978472] , Consumer (IN) PIPE 2, Producer (OUT) PIPE 3
789[ 8.978472] IO base BAM = 0x (null)
790[ 8.978472] BAM IRQ 239
791[ 8.978472] Engines Availability = 0x2010853
792[ 8.981669] mmc0: new HS200 MMC card at address 0001
793[ 9.007698] sps:BAM 0x00704000 is registered.[ 9.007727] mmcblk0: mmc0:0001 HAG4a2 14.6 GiB
794[ 9.008154] mmcblk0rpmb: mmc0:0001 HAG4a2 partition 3 4.00 MiB
795[ 9.011860] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 p33
796
797[ 9.041358] sps:BAM 0x00704000 (va:0xf06c0000) enabled: ver:0x25, number of pipes:8
798[ 9.054859] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000000704000 irq 239
799[ 9.062387] qcedev: FIPS140-2 Known Answer Tests : Skipped
800[ 9.069681] qcrypto 720000.qcrypto: Qualcomm Crypto 5.3.1 device found @0x720000
801[ 9.076116] qcrypto 720000.qcrypto: CE device = 0x0
802[ 9.076116] , IO base, CE = 0xf07c0000
803[ 9.076116] , Consumer (IN) PIPE 4, Producer (OUT) PIPE 5
804[ 9.076116] IO base BAM = 0x (null)
805[ 9.076116] BAM IRQ 239
806[ 9.076116] Engines Availability = 0x2010853
807[ 9.113310] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000000704000 irq 239
808[ 9.120980] qcrypto 720000.qcrypto: qcrypto-ecb-aes
809[ 9.125158] qcrypto 720000.qcrypto: qcrypto-cbc-aes
810[ 9.129964] qcrypto 720000.qcrypto: qcrypto-ctr-aes
811[ 9.134890] qcrypto 720000.qcrypto: qcrypto-ecb-des
812[ 9.139627] qcrypto 720000.qcrypto: qcrypto-cbc-des
813[ 9.144551] qcrypto 720000.qcrypto: qcrypto-ecb-3des
814[ 9.149444] qcrypto 720000.qcrypto: qcrypto-cbc-3des
815[ 9.154481] qcrypto 720000.qcrypto: qcrypto-xts-aes
816[ 9.159253] qcrypto 720000.qcrypto: qcrypto-sha1
817[ 9.163820] qcrypto 720000.qcrypto: qcrypto-sha256
818[ 9.168682] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-aes
819[ 9.174838] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-des
820[ 9.180961] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-3des
821[ 9.187301] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-aes
822[ 9.193513] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-des
823[ 9.200018] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-3des
824[ 9.206358] qcrypto 720000.qcrypto: qcrypto-hmac-sha1
825[ 9.211306] qcrypto 720000.qcrypto: qcrypto-hmac-sha256
826[ 9.216628] qcrypto 720000.qcrypto: qcrypto-aes-ccm
827[ 9.221448] qcrypto 720000.qcrypto: qcrypto-rfc4309-aes-ccm
828[ 9.226783] qcrypto: FIPS140-2 Known Answer Tests: Skipped
829[ 9.233407] usbcore: registered new interface driver usbhid
830[ 9.238065] usbhid: USB HID core driver
831[ 9.242542] zram: Created 1 device(s) ...
832[ 9.246834] ashmem: initialized
833[ 9.250436] logger: created 256K log 'log_main'
834[ 9.255514] logger: created 256K log 'log_events'
835[ 9.260631] logger: created 256K log 'log_radio'
836[ 9.265701] logger: created 256K log 'log_system'
837[ 9.270621] sps:BAM 0x078c4000 is registered.
838[ 9.274475] qcom,qpnp-power-on qpnp-power-on-1: PMIC@SID0 Power-on reason: Triggered from Hard Reset and 'cold' boot
839[ 9.284521] qcom,qpnp-power-on qpnp-power-on-1: PMIC@SID0: Power-off reason: Triggered from PS_HOLD (PS_HOLD/MSM controlled shutdown)
840[ 9.296858] input: qpnp_pon as /devices/virtual/input/input3
841[ 9.304762] geoff_type=13
842[ 9.306348] PMIC@SID0: PM8909 v1.1 options: 0, 2, 0, 0
843[ 9.335929] populate_opp_table: clock-a7: OPP tables populated (cpu 3)
844[ 9.341430] print_opp_table: clock_cpu: a7: OPP voltage for 400000000: 4
845[ 9.348160] print_opp_table: clock_cpu: a7: OPP voltage for 1094400000: 7
846[ 9.357054] bimc-bwmon 410000.qcom,gpu-bwmon: BW HWmon governor registered.
847[ 9.363261] bimc-bwmon 408000.qcom,cpu-bwmon: BW HWmon governor registered.
848[ 9.373626] devfreq qcom,cpubw.32: Couldn't update frequency transition information.
849[ 9.387052] coresight-fuse 5e01c.fuse: Fuse initialized
850[ 9.392214] coresight-cti 810000.cti: CTI initialized
851[ 9.396772] coresight-cti 811000.cti: CTI initialized
852[ 9.401633] coresight-cti 812000.cti: CTI initialized
853[ 9.406742] coresight-cti 813000.cti: CTI initialized
854[ 9.411673] coresight-cti 814000.cti: CTI initialized
855[ 9.416841] coresight-cti 815000.cti: CTI initialized
856[ 9.422204] coresight-cti 816000.cti: CTI initialized
857[ 9.426907] coresight-cti 817000.cti: CTI initialized
858[ 9.431854] coresight-cti 818000.cti: CTI initialized
859[ 9.436954] coresight-cti 851000.cti: CTI initialized
860[ 9.441898] coresight-cti 852000.cti: CTI initialized
861[ 9.447032] coresight-cti 853000.cti: CTI initialized
862[ 9.452012] coresight-cti 854000.cti: CTI initialized
863[ 9.457103] coresight-cti 83c000.cti: CTI initialized
864[ 9.462097] coresight-cti 838000.cti: CTI initialized
865[ 9.467215] coresight-cti 835000.cti: CTI initialized
866[ 9.472096] coresight-cti 830000.cti: CTI initialized
867[ 9.477819] coresight-csr 801000.csr: CSR initialized
868[ 9.482795] coresight-tmc 826000.tmc: Byte Counter feature enabled
869[ 9.488160] sps:BAM 0x00884000 is registered.
870[ 9.492612] coresight-tmc 826000.tmc: TMC initialized
871[ 9.498035] coresight-tmc 825000.tmc: TMC initialized
872[ 9.505920] nidnt boot config: 0
873[ 9.510108] coresight-tpiu 820000.tpiu: NIDnT on SDCARD only mode
874[ 9.515482] coresight-tpiu 820000.tpiu: TPIU initialized
875[ 9.521412] coresight-funnel 821000.funnel: FUNNEL initialized
876[ 9.526614] coresight-funnel 869000.funnel: FUNNEL initialized
877[ 9.532305] coresight-funnel 868000.funnel: FUNNEL initialized
878[ 9.538296] coresight-funnel 855000.funnel: FUNNEL initialized
879[ 9.544563] coresight-replicator 824000.replicator: REPLICATOR initialized
880[ 9.551511] coresight-dbgui 86d000.dbgui: DebugUI capture enabled
881[ 9.556924] coresight-dbgui 86d000.dbgui: DebugUI initializaed
882[ 9.563486] coresight-stm 802000.stm: STM initialized
883[ 9.568455] coresight-hwevent 86c000.hwevent: Hardware Event driver initialized
884[ 9.575986] coresight-etm 84c000.etm: ETM initialized
885[ 9.580504] coresight-etm 84d000.etm: ETM initialized
886[ 9.585745] coresight-etm 84e000.etm: ETM initialized
887[ 9.590710] coresight-etm 84f000.etm: ETM initialized
888[ 9.596593] coresight-modem-etm modem_etm0.26: Modem ETM initialized
889[ 9.603231] coresight-wcn-etm wcn_etm0.25: Wireless ETM initialized
890[ 9.609842] coresight-rpm-etm rpm_etm0.24: RPM ETM initialized
891[ 9.615884] coresight-qpdi 1941000.qpdi: CoreSight QPDI driver initialized
892[ 9.622148] test_proc_create
893[ 9.624764] proc create success
894[ 9.628120] usbcore: registered new interface driver snd-usb-audio
895[ 9.635662] spmi msm8x16_wcd_codec-12: Driver wcd-spmi-core requests probe deferral
896[ 9.642335] spmi msm8x16_wcd_codec-13: Driver wcd-spmi-core requests probe deferral
897[ 9.671602] msm-pcm-lpa qcom,msm-pcm-lpa.46: msm_pcm_probe: dev name qcom,msm-pcm-lpa.46
898[ 9.680198] platform qcom,msm-voip-dsp.48: Driver msm-voip-dsp requests probe deferral
899[ 9.688003] platform qcom,msm-pcm-voice.49: Driver msm-pcm-voice requests probe deferral
900[ 9.707482] msm8x16-asoc-wcd sound.71: default codec configured
901[ 9.715246] msm8x16-asoc-wcd sound.71: ASoC: platform (null) not registered
902[ 9.721230] msm8x16-asoc-wcd sound.71: snd_soc_register_card failed (-517)
903[ 9.728486] platform sound.71: Driver msm8x16-asoc-wcd requests probe deferral
904[ 9.735891] u32 classifier
905[ 9.737925] Actions configured
906[ 9.741317] Netfilter messages via NETLINK v0.30.
907[ 9.746201] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
908[ 9.753248] ctnetlink v0.93: registering with nfnetlink.
909[ 9.758568] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
910[ 9.764580] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
911[ 9.771086] xt_time: kernel timezone is -0000
912[ 9.775217] ip_tables: (C) 2000-2006 Netfilter Core Team
913[ 9.780353] arp_tables: (C) 2002 David S. Miller
914[ 9.784780] TCP: cubic registered
915[ 9.787846] Initializing XFRM netlink socket
916[ 9.793371] NET: Registered protocol family 10
917[ 9.798534] mip6: Mobile IPv6
918[ 9.800515] ip6_tables: (C) 2000-2006 Netfilter Core Team
919[ 9.806367] sit: IPv6 over IPv4 tunneling driver
920[ 9.811306] NET: Registered protocol family 17
921[ 9.815063] NET: Registered protocol family 15
922[ 9.819473] Bridge firewalling registered
923[ 9.823308] Ebtables v2.0 registered
924[ 9.827365] Bluetooth: ee855ef0
925[ 9.829853] Bluetooth: ee855ef0Bluetooth: ee855f00[ 9.834061] msm_bam_device_lpm_ok: Going to LPM now
926
927[ 9.839557] Bluetooth: ee855ed8Bluetooth: ee855ed8
928[ 9.844381] Bluetooth: ee855ed0Bluetooth: ee855f10
929[ 9.849050] Bluetooth: ee855f10[ 9.852212] l2tp_core: L2TP core driver, V2.0
930[ 9.856580] l2tp_ppp: PPPoL2TP kernel driver, V2.0
931[ 9.861275] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
932[ 9.866953] l2tp_netlink: L2TP netlink interface
933[ 9.871491] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
934[ 9.877521] l2tp_debugfs: L2TP debugfs support
935[ 9.881764] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
936[ 9.881884] msm_otg 78d9000.usb: USB in low power mode
937[ 9.908024] of_batterydata_read_data: palladium_1500mah loaded
938[ 9.924738] BMS: bms_load_hw_defaults: BMS_EN=1 Sample_Interval-S1=[100]S2=[70] Sample_Count-S1=[256]S2=[128] Fifo_Length-S1=[5]S2=[5] FSM_state=2
939[ 9.944865] BMS: calculate_initial_soc: warm_reset=0 est_ocv=0 shutdown_soc_invalid=0 shutdown_ocv=3882000 shutdown_soc=62 last_soc=62 calculated_soc=62 last_ocv_uv=3882000
940[ 9.973883] BMS: qpnp_vm_bms_probe: probe success: soc=62 vbatt=3797685 ocv=3882000 warm_reset=0
941[ 10.072477] msm_otg 78d9000.usb: USB exited from low power mode
942[ 10.079165] CHG: qpnp_lbc_main_probe: Probe chg_dis=0 bpd=1 usb=1 batt_pres=1 batt_volt=3814454 soc=62
943[ 10.087839] spmi msm8x16_wcd_codec-12: Driver wcd-spmi-core requests probe deferral
944[ 10.095418] spmi msm8x16_wcd_codec-13: Driver wcd-spmi-core requests probe deferral
945[ 10.124632] msm8x16-asoc-wcd sound.71: default codec configured
946[ 10.132537] msm8x16-asoc-wcd sound.71: ASoC: CODEC (null) not registered
947[ 10.138331] msm8x16-asoc-wcd sound.71: snd_soc_register_card failed (-517)
948[ 10.145467] platform sound.71: Driver msm8x16-asoc-wcd requests probe deferral
949[ 10.152391] spmi msm8x16_wcd_codec-12: Driver wcd-spmi-core requests probe deferral
950[ 10.160085] spmi msm8x16_wcd_codec-13: Driver wcd-spmi-core requests probe deferral
951[ 10.168704] Registering SWP/SWPB emulation handler
952[ 10.173943] Loading module verification certificates
953[ 10.186890] MODSIGN: Loaded cert 'Magrathea: Glacier signing key: 1e3e05b15ffa8e3d03dc13388bf6e89058920b1f'
954[ 10.375106] oem_otg_ext_vreg: disabling
955[ 10.377914] spk_vreg: disabling
956[ 10.381083] regulator-dummy: disabling
957[ 10.386022] msm8x16-asoc-wcd sound.71: default codec configured
958[ 10.393831] msm8x16-asoc-wcd sound.71: ASoC: CODEC (null) not registered
959[ 10.399696] msm8x16-asoc-wcd sound.71: snd_soc_register_card failed (-517)
960[ 10.406806] platform sound.71: Driver msm8x16-asoc-wcd requests probe deferral
961[ 10.413701] spmi msm8x16_wcd_codec-12: Driver wcd-spmi-core requests probe deferral
962[ 10.421347] spmi msm8x16_wcd_codec-13: Driver wcd-spmi-core requests probe deferral
963[ 10.431421] file system registered
964[ 10.434035] mbim_init: initialize 1 instances
965[ 10.438261] mbim_init: Initialized 1 ports
966[ 10.442205] mbim_bam_setup: no_ports:1
967[ 10.446328] mbim_bam_setup: Initialized 1 ports
968[ 10.452964] rndis_qc_init: initialize rndis QC instance
969[ 10.458234] android_usb gadget: Mass Storage Function, version: 2009/09/11
970[ 10.464127] android_usb gadget: Number of LUNs=1
971[ 10.468676] lun0: LUN: removable file: (no medium)
972[ 10.474384] android_usb gadget: android_usb ready
973[ 10.478227] msm_hsusb msm_hsusb: [ci13xxx_start] hw_ep_max = 16
974[ 10.484221] msm_hsusb msm_hsusb: CI13XXX_CONTROLLER_RESET_EVENT received
975[ 10.492084] msm8x16-asoc-wcd sound.71: default codec configured
976[ 10.494834] input: gpio-keys as /devices/soc.0/gpio_keys.70/input/input4
977[ 10.503670] qcom,qpnp-rtc qpnp-rtc-6: setting system clock to 1970-01-01 00:00:50 UTC (50)
978[ 10.506747] msm8x16-asoc-wcd sound.71: ASoC: CODEC (null) not registered
979[ 10.506808] msm8x16-asoc-wcd sound.71: snd_soc_register_card failed (-517)
980[ 10.507100] platform sound.71: Driver msm8x16-asoc-wcd requests probe deferral
981[ 10.507255] spmi msm8x16_wcd_codec-12: Driver wcd-spmi-core requests probe deferral
982[ 10.507343] spmi msm8x16_wcd_codec-13: Driver wcd-spmi-core requests probe deferral
983[ 10.508275] msm8x16-asoc-wcd sound.71: default codec configured
984[ 10.511162] msm8x16-asoc-wcd sound.71: ASoC: CODEC (null) not registered
985[ 10.511215] msm8x16-asoc-wcd sound.71: snd_soc_register_card failed (-517)
986[ 10.511556] platform sound.71: Driver msm8x16-asoc-wcd requests probe deferral
987[ 10.576351] msm_thermal:interrupt_mode_init Interrupt mode init
988[ 10.581244] msm_thermal:disable_msm_thermal Max frequency reset for CPU0
989[ 10.588807] msm_thermal:disable_msm_thermal Max frequency reset for CPU1
990[ 10.594727] msm_thermal:disable_msm_thermal Max frequency reset for CPU2
991[ 10.601311] msm_thermal:disable_msm_thermal Max frequency reset for CPU3
992[ 10.609934] spmi msm8x16_wcd_codec-12: Driver wcd-spmi-core requests probe deferral
993[ 10.610656] /soc/qcom,lpm-levels/qcom,pm-cluster@0: No CPU phandle, assuming single cluster
994[ 10.625005] spmi msm8x16_wcd_codec-13: Driver wcd-spmi-core requests probe deferral
995[ 10.633309] msm8x16-asoc-wcd sound.71: default codec configured
996[ 10.640653] msm8x16-asoc-wcd sound.71: ASoC: CODEC (null) not registered
997[ 10.646487] msm8x16-asoc-wcd sound.71: snd_soc_register_card failed (-517)
998[ 10.649729] led_gpio_flash_probe:probe successfully!
999[ 10.653827] qcom,cc-debug-8909 1874000.qcom,cc-debug: Registered Debug Mux successfully
1000[ 10.654874] ---+++ gpio_clk_probe succeeded
1001[ 10.655264] clock_late_init: Removing enables held for handed-off clocks
1002[ 10.658137] ALSA device list:
1003[ 10.658139] No soundcardsh��r������platform sound.71: Driver msm8x16-asoc-wcd requests probe deferral
1004[ 10.689954] spmi msm8x16_wcd_codec-12: Driver wcd-spmi-core requests probe deferral
1005[ 10.690424] Freeing unused kernel memory: 396K (c1100000 - c1163000)
1006[ 10.703918] spmi msm8x16_wcd_codec-13: Driver wcd-spmi-core requests probe deferral
1007[ 10.712257] msm8x16-asoc-wcd sound.71: default codec configured
1008[ 10.719558] msm8x16-asoc-wcd sound.71: ASoC: CODEC (null) not registered
1009[ 10.725331] msm8x16-asoc-wcd sound.71: snd_soc_register_card failed (-517)
1010[ 10.732209] platform sound.71: Driver msm8x16-asoc-wcd requests probe deferral
1011[ 10.744485] init: init first stage started!
1012[ 10.866010] type=1403 audit(50.859:2): policy loaded auid=4294967295 ses=4294967295
1013[ 10.874148] type=1404 audit(50.859:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
1014[ 10.964371] init: (Initializing SELinux enforcing took 0.22s.)
1015[ 10.978980] init: init second stage started!
1016[ 10.995571] init: property_set("ro.boot.bootdevice", "7824900.sdhci") failed
1017[ 11.009976] init: Running restorecon...
1018[ 11.312461] init: waitpid failed: No child processes
1019[ 11.317162] init: (Loading properties from /default.prop took 0.00s.)
1020[ 11.327948] init: (Parsing /init.environ.rc took 0.00s.)
1021[ 11.333482] init: (Parsing /init.usb.rc took 0.00s.)
1022[ 11.342664] init: /init.qcom.rc: 579: user requires 1 argument
1023[ 11.350402] init: ignored duplicate definition of service 'RIDL'init: (Parsing init.qcom.usb.rc took 0.01s.)
1024[ 11.372702] init: ignored duplicate definition of service 'perfd'init: init.target.rc: 153: invalid keyword 'load_all_props'
1025[ 11.384107] init: ignored duplicate definition of service 'poweroffhandler'init: (Parsing init.carrier.rc took 0.01s.)
1026[ 11.393787] init: (Parsing init.target.rc took 0.02s.)
1027[ 11.400870] init: (Parsing init.qcom.factory.rc took 0.00s.)
1028[ 11.405639] init: (Parsing /init.qcom.rc took 0.07s.)
1029[ 11.413110] init: (Parsing /init.usb.configfs.rc took 0.00s.)
1030[ 11.418094] init: (Parsing /init.zygote32.rc took 0.00s.)
1031[ 11.423228] init: (Parsing /init.rc took 0.10s.)
1032[ 11.429087] init: Starting service 'ueventd'...
1033[ 11.435129] init: Waiting for /dev/.coldboot_done...
1034[ 11.439440] ueventd: ueventd started!
1035[ 12.469381] ueventd: Coldboot took 1.02s.
1036[ 12.474221] init: Waiting for /dev/.coldboot_done took 1.04s.
1037[ 12.498126] init: write_file: Unable to open '/proc/sys/kernel/hung_task_timeout_secs': No such file or directory
1038[ 12.519522] init: write_file: Unable to open '/proc/sys/abi/swp': No such file or directory
1039[ 12.631005] EXT4-fs (mmcblk0p21): mounted filesystem with ordered data mode. Opts: barrier=1
1040[ 12.638660] fs_mgr: __mount(source=/dev/block/bootdevice/by-name/system,target=/system,type=ext4)=0
1041[ 12.649077] EXT4-fs (mmcblk0p33): Ignoring removed nomblk_io_submit option
1042[ 12.662085] EXT4-fs (mmcblk0p33): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit
1043[ 12.671976] fs_mgr: check_fs(): mount(/dev/block/bootdevice/by-name/userdata,/data,ext4)=0: Success
1044[ 12.682467] fs_mgr: check_fs(): unmount(/data) succeeded
1045[ 12.688188] fs_mgr: Running /system/bin/e2fsck on /dev/block/bootdevice/by-name/userdata
1046[ 13.564085] e2fsck (242) used greatest stack depth: 5444 bytes left
1047[ 13.569667] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
1048[ 13.569667]
1049[ 13.575413] e2fsck: Pass 1: Checking inodes, blocks, and sizes
1050[ 13.575413]
1051[ 13.582607] e2fsck: Pass 2: Checking directory structure
1052[ 13.582607]
1053[ 13.589417] e2fsck: Pass 3: Checking directory connectivity
1054[ 13.589417]
1055[ 13.596491] e2fsck: Pass 4: Checking reference counts
1056[ 13.596491]
1057[ 13.602918] e2fsck: Pass 5: Checking group summary information
1058[ 13.602918]
1059[ 13.610359] e2fsck: data: 2764/316992 files (9.8% non-contiguous), 105746/1267451 blocks
1060[ 13.610359]
1061[ 13.625660] EXT4-fs (mmcblk0p33): mounted filesystem with ordered data mode. Opts: barrier=1,noauto_da_alloc,discard
1062[ 13.635424] fs_mgr: __mount(source=/dev/block/bootdevice/by-name/userdata,target=/data,type=ext4)=0
1063[ 13.648578] init (235) used greatest stack depth: 5120 bytes left
1064[ 13.663724] init: (Parsing /system/etc/init/atrace.rc took 0.00s.)
1065[ 13.669704] init: (Parsing /system/etc/init/audioserver.rc took 0.00s.)
1066[ 13.676191] init: (Parsing /system/etc/init/bootanim.rc took 0.00s.)
1067[ 13.682573] init: (Parsing /system/etc/init/bootstat.rc took 0.00s.)
1068[ 13.689099] init: (Parsing /system/etc/init/cameraserver.rc took 0.00s.)
1069[ 13.695521] init: (Parsing /system/etc/init/debuggerd.rc took 0.00s.)
1070[ 13.701885] init: (Parsing /system/etc/init/drmserver.rc took 0.00s.)
1071[ 13.708794] init: (Parsing /system/etc/init/dumpstate.rc took 0.00s.)
1072[ 13.714972] init: (Parsing /system/etc/init/gatekeeperd.rc took 0.00s.)
1073[ 13.721458] init: (Parsing /system/etc/init/init-debug.rc took 0.00s.)
1074[ 13.728064] init: (Parsing /system/etc/init/installd.rc took 0.00s.)
1075[ 13.734209] init: (Parsing /system/etc/init/keystore.rc took 0.00s.)
1076[ 13.740559] init: (Parsing /system/etc/init/lmkd.rc took 0.00s.)
1077[ 13.747142] init: (Parsing /system/etc/init/logcatd.rc took 0.00s.)
1078[ 13.753082] init: (Parsing /system/etc/init/logd.rc took 0.00s.)
1079[ 13.759185] init: (Parsing /system/etc/init/mdnsd.rc took 0.00s.)
1080[ 13.765143] init: (Parsing /system/etc/init/mediacodec.rc took 0.00s.)
1081[ 13.771571] init: (Parsing /system/etc/init/mediadrmserver.rc took 0.00s.)
1082[ 13.778589] init: (Parsing /system/etc/init/mediaextractor.rc took 0.00s.)
1083[ 13.785360] init: (Parsing /system/etc/init/mediaserver.rc took 0.00s.)
1084[ 13.791854] init: (Parsing /system/etc/init/mtpd.rc took 0.00s.)
1085[ 13.797927] init: (Parsing /system/etc/init/netd.rc took 0.00s.)
1086[ 13.803805] init: (Parsing /system/etc/init/perfprofd.rc took 0.00s.)
1087[ 13.810518] init: (Parsing /system/etc/init/racoon.rc took 0.00s.)
1088[ 13.816581] init: (Parsing /system/etc/init/rild.rc took 0.00s.)
1089[ 13.822461] init: (Parsing /system/etc/init/servicemanager.rc took 0.00s.)
1090[ 13.829387] init: (Parsing /system/etc/init/surfaceflinger.rc took 0.00s.)
1091[ 13.836342] init: (Parsing /system/etc/init/uncrypt.rc took 0.00s.)
1092[ 13.842426] init: (Parsing /system/etc/init/vdc.rc took 0.00s.)
1093[ 13.848401] init: (Parsing /system/etc/init/vold.rc took 0.00s.)
1094[ 13.861968] EXT4-fs (mmcblk0p23): mounted filesystem with ordered data mode. Opts: barrier=1
1095[ 13.877243] EXT4-fs (mmcblk0p22): mounted filesystem with ordered data mode. Opts: barrier=1
1096[ 13.895798] EXT4-fs (mmcblk0p27): VFS: Can't find ext4 filesystem
1097[ 13.903388] init: Starting service 'logd'...
1098[ 13.960770] logd.auditd: start
1099[ 13.962829] logd.klogd: 13958846713
1100[ 14.718265] init: (Loading properties from /system/vendor/Default/system/vendor/vendor.prop took 0.00s.)
1101[ 14.726875] init: (Loading properties from /persist/speccfg/vendor_ro.prop took 0.01s.)
1102[ 14.738149] init: (Loading properties from /system/vendor/vendor.prop took 0.00s.)
1103[ 14.746146] init: (Loading properties from /system/vendor/Default/system/vendor/vendor.prop took 0.00s.)
1104[ 14.754739] init: (Loading properties from /persist/speccfg/vendor_persist.prop took 0.01s.)
1105[ 14.763941] init: property_set("ro.telephony.default_network", "22,20") failed
1106[ 14.770488] init: (Loading properties from /system/vendor/default.prop took 0.01s.)
1107[ 14.778067] init: (Loading properties from /system/vendor/power.prop took 0.00s.)
1108[ 14.785395] init: (Loading properties from /system/build.prop took 0.07s.)
1109[ 14.792260] init: (Loading properties from /vendor/build.prop took 0.00s.)
1110[ 14.799144] init: (Loading properties from /factory/factory.prop took 0.00s.)
1111[ 14.806565] init: /recovery not specified in fstab
1112[ 14.811981] init: Starting service 'debuggerd'...
1113[ 14.816983] init: do_start: Service debuggerd64 not found
1114[ 14.824726] init: Starting service 'vold'...
1115[ 14.831627] init: Not bootcharting.
1116[ 15.103748] init: Starting service 'exec 1 (/system/bin/tzdatacheck)'...
1117[ 15.142794] init: Service 'exec 1 (/system/bin/tzdatacheck)' (pid 265) exited with status 0
1118[ 15.209475] init: Starting service 'carrier_switcher'...
1119[ 15.216783] init: (Loading properties from /data/local.prop took 0.00s.)
1120[ 15.407492] init: Starting service 'logd-reinit'...
1121[ 15.412915] init: property 'persist.sys.ssr.enable_debug' doesn't exist while expanding '${persist.sys.ssr.enable_debug}'
1122[ 15.423149] init: write: cannot expand '${persist.sys.ssr.enable_debug}'
1123[ 15.429734] init: property 'persist.sys.mba_boot_timeout' doesn't exist while expanding '${persist.sys.mba_boot_timeout}'
1124[ 15.440664] init: write: cannot expand '${persist.sys.mba_boot_timeout}'
1125[ 15.447402] init: property 'persist.sys.modem_auth_timeout' doesn't exist while expanding '${persist.sys.modem_auth_timeout}'
1126[ 15.458575] init: write: cannot expand '${persist.sys.modem_auth_timeout}'
1127[ 15.458589] logd.daemon: reinit
1128[ 15.468934] init: Service 'logd-reinit' (pid 270) exited with status 0
1129[ 15.475147] init: property 'persist.sys.pil_proxy_timeout' doesn't exist while expanding '${persist.sys.pil_proxy_timeout}'
1130[ 15.486179] init: write: cannot expand '${persist.sys.pil_proxy_timeout}'
1131[ 15.498284] pil-q6v5-mss 4080000.qcom,mss: modem: loading from 0x88000000 to 0x8d300000
1132[ 15.523666] pil-q6v5-mss 4080000.qcom,mss: MBA: loading from 0xaf400000 to 0xaf500000
1133[ 15.576783] pil-q6v5-mss 4080000.qcom,mss: MBA boot done
1134[ 16.382566] pil-q6v5-mss 4080000.qcom,mss: modem: Brought out of reset
1135[ 16.459234] spmi msm8x16_wcd_codec-12: Driver wcd-spmi-core requests probe deferral
1136[ 16.465992] pil-q6v5-mss 4080000.qcom,mss: Subsystem error monitoring/handling services are up
1137[ 16.474491] memshare: Modem Restart has happened
1138[ 16.474506] pil-q6v5-mss 4080000.qcom,mss: modem: Power/Clock ready interrupt received
1139[ 16.475914] sysmon-qmi: sysmon_clnt_svc_arrive: Connection established between QMI handle and modem's SSCTL service
1140[ 16.475973] spmi msm8x16_wcd_codec-13: Driver wcd-spmi-core requests probe deferral
1141[ 16.476761] msm8x16-asoc-wcd sound.71: default codec configured
1142[ 16.478959] msm8x16-asoc-wcd sound.71: ASoC: CODEC (null) not registered
1143[ 16.479007] msm8x16-asoc-wcd sound.71: snd_soc_register_card failed (-517)
1144[ 16.479153] platform sound.71: Driver msm8x16-asoc-wcd requests probe deferral
1145[ 16.479291] spmi msm8x16_wcd_codec-12: Driver wcd-spmi-core requests probe deferral
1146[ 16.479357] spmi msm8x16_wcd_codec-13: Driver wcd-spmi-core requests probe deferral
1147[ 16.547358] M-Notify: General: 7
1148[ 16.547392] init: Service 'carrier_switcher' (pid 266) exited with status 0
1149[ 16.547633] init: Starting service 'exec 2 (/init.qcom.early_boot.sh)'...
1150[ 16.791863] init: property_set("ro.opengles.version", "196608") failed
1151[ 17.347341] init: Service 'exec 2 (/init.qcom.early_boot.sh)' (pid 291) exited with status 0
1152[ 17.360118] init: Starting service 'healthd'...
1153[ 17.365366] init: Starting service 'qcom-debug'...
1154[ 17.370144] binder: 319:319 transaction failed 29189, size 0-0
1155[ 17.370750] init: Starting service 'qcom-c_core-sh'...
1156[ 17.372354] init: Starting service 'config_bluetooth'...
1157[ 17.374315] init: Starting service 'qseecomd'...
1158[ 17.376160] init: Starting service 'per_mgr'...
1159[ 17.378209] init: Starting service 'lmkd'...
1160[ 17.380205] init: Starting service 'servicemanager'...
1161[ 17.382138] init: Starting service 'surfaceflinger'...
1162[ 17.397094] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet0/accept_ra': No such file or directory
1163[ 17.397163] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet1/accept_ra': No such file or directory
1164[ 17.397228] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet2/accept_ra': No such file or directory
1165[ 17.397292] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet3/accept_ra': No such file or directory
1166[ 17.397365] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet4/accept_ra': No such file or directory
1167[ 17.397427] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet5/accept_ra': No such file or directory
1168[ 17.397491] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet6/accept_ra': No such file or directory
1169[ 17.397557] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet7/accept_ra': No such file or directory
1170[ 17.397626] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_sdio0/accept_ra': No such file or directory
1171[ 17.397693] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_sdio1/accept_ra': No such file or directory
1172[ 17.397763] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_sdio2/accept_ra': No such file or directory
1173[ 17.397837] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_sdio3/accept_ra': No such file or directory
1174[ 17.397907] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_sdio4/accept_ra': No such file or directory
1175[ 17.397971] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_sdio5/accept_ra': No such file or directory
1176[ 17.398034] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_sdio6/accept_ra': No such file or directory
1177[ 17.398095] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_sdio7/accept_ra': No such file or directory
1178[ 17.398157] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_usb0/accept_ra': No such file or directory
1179[ 17.398221] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_usb1/accept_ra': No such file or directory
1180[ 17.398282] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_usb2/accept_ra': No such file or directory
1181[ 17.398353] init: write_file: Unable to open '/proc/sys/net/ipv6/conf/rmnet_usb3/accept_ra': No such file or directory
1182[ 17.399588] init: Starting service 'rmt_storage'...
1183[ 17.647595] init: insmod: open("/system/lib/modules/adsprpc.ko") failed: No such file or directoryinit: Starting service 'console'...
1184[ 17.662661] enable_store: android_usb: already disabled
1185[ 17.672815] init: Starting service 'adbd'..[ 17.681407] init: Starting service 'ppd'...
1186[ 17.704717] init: cannot find '/system/bin/update_verifier' (No such file or directory), disabling 'exec 3 (/system/bin/update_verifier)'
1187[ 17.735691] init: cannot find '/system/bin/install-recovery.sh' (No such file or directory), disabling 'flash_recovery'
1188[ 17.747433] init: Starting service 'qcomsysd'...
1189[ 17.762206] init: Starting service 'qcom-c_main-sh'...
1190[ 17.775464] init: Starting service 'cnd'...
1191[ 17.780984] init: Starting service 'irsc_util'...
1192[ 17.807955] init: Starting service 'tftp_server'...
1193[ 17.826413] init: Starting service 'ptt_socket_app'...
1194[ 17.833561] init: Starting service 'cnss_diag'...
1195[ 17.839585] init: Starting service 'atfwd_quec'...
1196[ 17.845793] init: Starting service 'quecserver'...
1197[ 17.851109] init: cannot find '/system/bin/usb_uicc_client' (No such file or directory), disabling 'usb_uicc_daemon'
1198[ 17.857685] handle_qmi_request: Error getting req_desc for msg_id 36
1199[ 17.857747] mem_share_svc_recv_msg: Error receiving message
1200[ 17.875347] init: Starting service 'bms-sh'...
1201[ 17.876426] msm8x16-asoc-wcd sound.71: ASoC: CODEC (null) not registered
1202[ 17.876476] msm8x16-asoc-wcd sound.71: snd_soc_register_card failed (-517)
1203[ 17.878897] diag: In diag_dci_write_proc, invalid data 0x00000000, peripheral: 0, len: 527
1204[ 17.903786] init: Starting service 'qcom-usb-sh'...
1205[ 17.910709] init: cannot find '/system/bin/qrngd' (No such file or directory), disabling 'qrngd'
1206msm8909:/ $ [ 17.937171] msm-pcm-routing qcom,msm-pcm-routing.43: ASoC: no dapm match for VOICEMMODE1_DL --> VoiceMMode1 --> SEC_MI2S_RX_Voice Mixer
1207[ 17.941424] init: Starting service 'thermal-engine'...
1208[ 17.943368] init: Starting service 'wcnss-service'...
1209[ 17.945423] init: Starting service 'imsstarter'...
1210[ 17.946644] init: cannot find '/system/bin/dts_configurator' (No such file or directory), disabling 'dts_configurator'
1211[ 17.947642] init: Starting service 'zygote'...
1212[ 17.949852] init: Starting service 'audioserver'...
1213[ 17.952271] init: Starting service 'cameraserver'...
1214[ 17.983066] init: couldn't write 371 to /dev/cpuset/camera-daemon/tasks: No such file or directory
1215[ 17.984537] init: Starting service 'drm'...
1216[ 17.986733] init: Starting service 'installd'...
1217[ 17.989000] init: Starting service 'keystore'...
1218[ 17.991177] init: Starting service 'mediacodec'...
1219[ 17.993291] init: Starting service 'mediadrm'...
1220[ 18.022716] init: Starting service 'mediaextractor'...
1221[ 18.024915] msm-pcm-routing qcom,msm-pcm-routing.43: ASoC: Failed to add route VOICEMMODE1_DL -> VoiceMMode1 -> SEC_MI2S_RX_Voice Mixer
1222[ 18.024977] msm-pcm-routing qcom,msm-pcm-routing.43: ASoC: no dapm match for VOICEMMODE2_DL --> VoiceMMode2 --> SEC_MI2S_RX_Voice Mixer
1223[ 18.024987] msm-pcm-routing qcom,msm-pcm-routing.43: ASoC: Failed to add route VOICEMMODE2_DL -> VoiceMMode2 -> SEC_MI2S_RX_Voice Mixer
1224[ 18.029174] msm-pcm-routing qcom,msm-pcm-routing.43: ASoC: no dapm match for VOICE2_STUB_DL --> Voice2 Stub --> INTERNAL_BT_SCO_RX_Voice Mixer
1225[ 18.029184] msm-pcm-routing qcom,msm-pcm-routing.43: ASoC: Failed to add route VOICE2_STUB_DL -> Voice2 Stub -> INTERNAL_BT_SCO_RX_Voice Mixer
1226[ 18.062543] msm-pcm-routing qcom,msm-pcm-routing.43: ASoC: mux SLIM_0_RX AANC MUX has no paths
1227[ 18.110125] wcd-spmi-core msm8x16_wcd_codec-12: ASoC: mux RX3 MIX1 INP3 has no paths
1228[ 18.113629] init: Starting service 'media'...
1229[ 18.125490] init: Starting service 'netd'...
1230[ 18.131189] init: Starting service 'ril-daemon'...
1231[ 18.144741] wcd-spmi-core msm8x16_wcd_codec-12: ASoC: mux RX2 MIX1 INP3 has no paths
1232[ 18.157491] init: Starting service 'dpmd'...
1233[ 18.163165] init: Starting service 'cnss-daemon'...
1234[ 18.172692] init: Starting service 'loc_launcher'...
1235[ 18.179165] init: Starting service 'qcom-sh'...
1236[ 18.181259] init: Service fuse_uicc0 does not have a SELinux domain defined.
1237[ 18.181961] init: Starting service 'RIDL'...
1238[ 18.194598] init: Starting service 'fidodaemon'...
1239[ 18.201166] init: Starting service 'qcamerasvr'...
1240[ 18.217278] init: Starting service 'time_daemon'...
1241[ 18.223888] init: Starting service 'audiod'...
1242[ 18.242117] init: Starting service 'gatekeeperd'...
1243[ 18.252120] gbam_connect_work: Bam channel is not ready
1244[ 18.511778] init: Starting service 'perfprofd'...
1245[ 18.525529] init: Service 'qcom-debug' (pid 320) exited with status 0
1246[ 18.551326] init: Service 'qcom-c_core-sh' (pid 321) exited with status 0
1247[ 18.570653] init: Service 'irsc_util' (pid 351) exited with status 0
1248[ 18.577092] init: Service 'cnss_diag' (pid 355) exited with status 255
1249[ 18.629821] healthd: BatteryTechnologyPath not found
1250[ 18.633784] healthd: BatteryFullChargePath not found
1251[ 18.704100] healthd: BatteryCycleCountPath not found
1252[ 18.938808] init: Starting service 'qmuxd'...
1253[ 19.010931] init: Starting service 'vm_bms'...
1254[ 19.071278] IPC_RTR: msm_ipc_router_send_to: Remote port not found
1255[ 19.105131] IPC_RTR: msm_ipc_router_sendmsg: Send_to failure -19
1256[ 19.134735] init: Service 'bms-sh' (pid 363) exited with status 0
1257[ 19.196083] init: cannot find '/system/bin/ipacm-diag' (No such file or directory), disabling 'ipacm-diag'
1258[ 19.286124] devbw qcom,gpubw.23: Governor already resumed!
1259[ 19.290590] devbw qcom,gpubw.23: Unable to resume BW HW mon governor (-16)
1260[ 19.293862] QSEECOM: qseecom_load_app: App (keymaste) does'nt exist, loading apps for first time
1261[ 19.318207] QSEECOM: qseecom_load_app: App with id 2 (keymaste) now loaded
1262[ 19.327435] init: cannot find '/system/bin/ipacm' (No such file or directory), disabling 'ipacm'
1263[ 19.399306] init: Starting service 'imsqmidaemon'...
1264[ 19.454582] init: Service 'imsstarter' (pid 368) exited with status 0
1265[ 19.820538] init: Starting service 'imsdatadaemon'...
1266[ 19.934266] init: Starting service 'ril-daemon2'...
1267[ 20.239243] init: Starting service 'qti'...
1268[ 20.543685] init: Starting service 'netmgrd'...
1269[ 20.648956] init: Starting service 'bootanim'...
1270[ 20.836619] init: Service 'qcom-c_main-sh' (pid 347) exited with status 0
1271[ 20.854452] init: Service 'qcom-usb-sh' (pid 364) exited with status 0
1272[ 21.527414] msm_qti_pp_get_rms_value_control, back not active to query rms be_idx:3
1273[ 21.544473] msm_dolby_dap_param_to_get_control_get, port_id not set, do not query ADM
1274[ 21.551374] msm_dolby_dap_param_visualizer_control_get Incorrect VCNB length
1275[ 21.565536] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
1276[ 21.572194] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
1277[ 21.604201] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1278[ 21.610699] msm_audio_sound_focus_get: Could not get copp idx for port_id=16385
1279[ 21.625360] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1280[ 21.630690] msm_audio_source_tracking_get: Could not get copp idx for port_id=16385
1281[ 21.654800] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
1282[ 21.661280] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
1283[ 21.685381] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1284[ 21.691847] msm_audio_sound_focus_get: Could not get copp idx for port_id=4101
1285[ 21.707171] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1286[ 21.712503] msm_audio_sound_focus_get: Could not get copp idx for port_id=4103
1287[ 21.735317] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1288[ 21.740652] msm_audio_source_tracking_get: Could not get copp idx for port_id=4103
1289[ 21.767391] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1290[ 21.772720] msm_audio_source_tracking_get: Could not get copp idx for port_id=4101
1291[ 21.842265] msm_pcm_volume_ctl_get substream runtime not found
1292[ 21.864354] msm_pcm_volume_ctl_get substream runtime not found
1293[ 21.869594] msm_pcm_volume_ctl_get substream runtime not found
1294[ 21.884443] msm_pcm_volume_ctl_get substream runtime not found
1295[ 21.894194] msm_pcm_volume_ctl_get substream or runtime not found
1296[ 21.899870] msm_pcm_volume_ctl_get substream runtime not found
1297[ 22.267951] wcdcal_hwdep_ioctl_shared: codec didn't set this 0!!
1298[ 22.273267] wcdcal_hwdep_ioctl_shared: codec didn't set this 1!!
1299[ 22.309620] wcdcal_hwdep_ioctl_shared: codec didn't set this 3!!
1300[ 22.342373] msm_ds2_dap_set_security_control: dmid 0 license key 0
1301[ 22.364615] core_set_license: Invalid cal block to send
1302[ 22.368635] msm_ds2_dap_set_security_control: failed to set dolby license[ 22.405444] wcdcal_hwdep_ioctl_shared: codec didn't set this 0!!
1303[ 22.410743] wcdcal_hwdep_ioctl_shared: codec didn't set this 1!!
1304[ 22.425795] wcdcal_hwdep_ioctl_shared: codec didn't set this 3!!
1305[ 22.896336] msm_qti_pp_get_rms_value_control, back not active to query rms be_idx:3
1306[ 22.918119] msm_dolby_dap_param_to_get_control_get, port_id not set, do not query ADM
1307[ 22.944260] msm_dolby_dap_param_visualizer_control_get Incorrect VCNB length
1308[ 22.950358] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
1309[ 22.984217] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
1310[ 22.991389] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1311[ 23.024166] msm_audio_sound_focus_get: Could not get copp idx for port_id=16385
1312[ 23.030575] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1313[ 23.064085] msm_audio_source_tracking_get: Could not get copp idx for port_id=16385
1314[ 23.070838] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
1315[ 23.104209] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
1316[ 23.111428] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1317[ 23.140871] msm_audio_sound_focus_get: Could not get copp idx for port_id=4101
1318[ 23.161358] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1319[ 23.166937] msm_audio_sound_focus_get: Could not get copp idx for port_id=4103
1320[ 23.174312] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1321[ 23.180308] msm_audio_source_tracking_get: Could not get copp idx for port_id=4103
1322[ 23.204197] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
1323[ 23.209528] msm_audio_source_tracking_get: Could not get copp idx for port_id=4101
1324[ 23.281021] msm_pcm_volume_ctl_get substream runtime not found
1325[ 23.294367] msm_pcm_volume_ctl_get substream runtime not found
1326[ 23.304653] msm_pcm_volume_ctl_get substream runtime not found
1327[ 23.331739] msm_pcm_volume_ctl_get substream runtime not found
1328[ 23.341783] msm_pcm_volume_ctl_get substream or runtime not found
1329[ 23.352285] msm_pcm_volume_ctl_get substream runtime not found
1330[ 23.563184] init: Service 'qcom-sh' (pid 399) exited with status 0
1331[ 23.981111] init: Service 'RIDL' (pid 400) exited with status 65
1332[ 24.006862] msm_camera_fill_vreg_params:65 i 2 j 0 cam_vio
1333[ 24.011362] msm_camera_fill_vreg_params:76 i 3 j 1 cam_vana
1334[ 24.019571] msm_camera_fill_vreg_params:76 i 4 j 1 cam_vana
1335[ 24.024210] msm_camera_fill_vreg_params:65 i 5 j 0 cam_vio
1336[ 24.069396] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:2 tx:1) mode:FIFO slv_addr:0x30 MSTR_STS:0x0d1300c8 OPER:0x00000010
1337[ 24.084198] msm_sensor_match_id: hi259: read id failed
1338[ 24.089626] msm_sensor_check_id:1336 match id failed rc -107
1339[ 24.174181] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:2 tx:1) mode:FIFO slv_addr:0x30 MSTR_STS:0x0d1300c8 OPER:0x00000010
1340[ 24.188986] msm_sensor_match_id: hi259: read id failed
1341[ 24.194145] msm_sensor_check_id:1336 match id failed rc -107
1342[ 24.283233] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:2 tx:1) mode:FIFO slv_addr:0x30 MSTR_STS:0x0d1300c8 OPER:0x00000010
1343[ 24.298228] msm_sensor_match_id: hi259: read id failed
1344[ 24.303061] msm_sensor_check_id:1336 match id failed rc -107
1345[ 24.339329] configuring dma source while dma is active
1346[ 24.354088] hi259 power up failed
1347[ 24.356210] MSM-SENSOR-INIT msm_sensor_driver_cmd:80 failed: msm_sensor_driver_probe rc -107
1348[ 24.368391] msm_camera_fill_vreg_params:65 i 0 j 1 cam_vio
1349[ 24.372854] msm_camera_fill_vreg_params:76 i 1 j 2 cam_vana
1350[ 24.378560] msm_camera_fill_vreg_params:76 i 5 j 2 cam_vana
1351[ 24.384040] msm_camera_fill_vreg_params:65 i 6 j 1 cam_vio
1352[ 24.418610] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:2 tx:2) mode:FIFO slv_addr:0x20 MSTR_STS:0x0d1300c8 OPER:0x00000010
1353[ 24.433408] msm_sensor_match_id: hi843_8909: read id failed
1354[ 24.439106] msm_sensor_check_id:1336 match id failed rc -107
1355[ 24.521894] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:2 tx:2) mode:FIFO slv_addr:0x20 MSTR_STS:0x0d1300c8 OPER:0x00000010
1356[ 24.537601] msm_sensor_match_id: hi843_8909: read id failed
1357[ 24.542153] msm_sensor_check_id:1336 match id failed rc -107
1358[ 24.622154] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:2 tx:2) mode:FIFO slv_addr:0x20 MSTR_STS:0x0d1300c8 OPER:0x00000010
1359[ 24.636964] msm_sensor_match_id: hi843_8909: read id failed
1360[ 24.642543] msm_sensor_check_id:1336 match id failed rc -107
1361[ 24.694052] hi843_8909 power up failed
1362[ 24.696603] MSM-SENSOR-INIT msm_sensor_driver_cmd:80 failed: msm_sensor_driver_probe rc -107
1363[ 24.725760] msm_isp_close_node: halt timeout rc=0
1364[ 25.151151] IPC_RTR: msm_ipc_router_send_to: permission failure for rild
1365[ 25.158306] IPC_RTR: msm_ipc_router_sendmsg: Send_to failure -1
1366[ 25.165506] IPC_RTR: msm_ipc_router_send_to: permission failure for rild
1367[ 25.171619] IPC_RTR: msm_ipc_router_sendmsg: Send_to failure -1
1368[ 25.256903] Couldn't get snoc_qosgen
1369[ 25.700743] IPC_RTR: msm_ipc_router_send_to: permission failure for rild
1370[ 25.706971] IPC_RTR: msm_ipc_router_sendmsg: Send_to failure -1
1371[ 25.712887] IPC_RTR: msm_ipc_router_send_to: permission failure for rild
1372[ 25.719340] IPC_RTR: msm_ipc_router_sendmsg: Send_to failure -1
1373[ 25.863235] init: property_set("ro.ril.svlte1x", "false") failed
1374[ 25.871302] init: property_set("ro.ril.svdo", "false") failed
1375[ 26.033014] wcnss: no space available for smd frame
1376[ 26.074626] wcnss: no space available for smd frame
1377[ 26.125339] wcnss: no space available for smd frame
1378[ 26.154438] wcnss: no space available for smd frame
1379[ 26.184132] wcnss: no space available for smd frame
1380[ 26.214169] wcnss: no space available for smd frame
1381[ 26.697862] init: Service 'config_bluetooth' (pid 322) exited with status 0
1382[ 40.557558] BootAnimation (717) used greatest stack depth: 5032 bytes left
1383[ 40.607245] init: Service 'bootanim' (pid 542) exited with status 0
1384[ 40.777790] init: Starting service 'qti-testscripts'...
1385[ 40.794678] init: Starting service 'atfwd'...
1386[ 40.800414] init: Starting service 'dmclient'...
1387[ 40.815727] init: cannot find '/system/bin/qrngp' (No such file or directory), disabling 'qrngp'
1388[ 40.825851] init: Starting service 'exec 4 (/system/bin/bootstat)'...
1389[ 40.839882] type=1400 audit(80.909:4): avc: denied { getattr } for pid=4086 comm="dmclient" path="/vendor" dev="rootfs" ino=2150 scontext=u:r:dmclient:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
1390[ 40.851459] init: Service 'qti-testscripts' (pid 4074) exited with status 0
1391[ 40.904390] init: Service 'exec 4 (/system/bin/bootstat)' (pid 4088) exited with status 0
1392[ 40.912285] init: Starting service 'exec 5 (/system/bin/bootstat)'...
1393[ 40.986826] init: Service 'exec 5 (/system/bin/bootstat)' (pid 4092) exited with status 0
1394[ 40.994845] init: Starting service 'exec 6 (/system/bin/bootstat)'...
1395[ 41.047851] init: Service 'exec 6 (/system/bin/bootstat)' (pid 4098) exited with status 0
1396[ 41.055818] init: Starting service 'exec 7 (/system/bin/bootstat)'...
1397[ 41.094880] Request for unknown module key 'Magrathea: Glacier signing key: 0c72b4353433056b2cc9d98393df985ebf3803cb' err -11
1398[ 41.122332] init: Service 'exec 7 (/system/bin/bootstat)' (pid 4101) exited with status 0
1399[ 41.845677] init: Starting service 'perfd'...
1400[ 41.858961] init: Service 'qcom-post-boot' (pid 4073) exited with status 0
1401[ 43.157546] i2c-msm-v2 78b5000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x48 MSTR_STS:0x0d1300c8 OPER:0x00000090
1402[ 43.176962] stk3x1x_software_reset: software reset: write i2c error, ret=-107
1403[ 43.194578] stk_ps 1-0048: Failed to re-init device setting
1404[ 43.200809] sensors stk3x1x-proximity: Invalid sensor class delay handle
1405[ 44.856793] type=1400 audit(84.929:5): avc: denied { read } for pid=4463 comm="RenderThread" name="gpuclk" dev="sysfs" ino=10941 scontext=u:r:untrusted_app:s0:c512,c768 tcontext=u:object_r:sysfs:s0 tclass=file permissive=0
1406[ 46.497866] init: avc: granted { set } for property=net.lte.ims.data.enabled pid=3794 uid=1001 gid=1001 scontext=u:r:radio:s0 tcontext=u:object_r:net_radio_prop:s0 tclass=property_service
1407[ 100.958509] type=1400 audit(141.029:6): avc: denied { read } for pid=4086 comm="dmclient" name="name" dev="sysfs" ino=10462 scontext=u:r:dmclient:s0 tcontext=u:object_r:sysfs:s0 tclass=file permissive=0
1408[ 101.064682] type=1400 audit(141.139:7): avc: denied { search } for pid=4086 comm="dmclient" name="/" dev="mmcblk0p23" ino=2 scontext=u:r:dmclient:s0 tcontext=u:object_r:cache_file:s0 tclass=dir permissive=0
1409[ 122.393900] type=1400 audit(162.459:8): avc: denied { sys_ptrace } for pid=4127 comm="perfd" capability=19 scontext=u:r:perfd:s0 tcontext=u:r:perfd:s0 tclass=capability permissive=0
1410[ 129.776468] Error: ret