· 5 years ago · Feb 01, 2020, 10:26 PM
1=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2020.02.01 00:50:03 =~=~=~=~=~=~=~=~=~=~=~=
2
3
4BootROM - 1.51
5
6Booting from SPI flash
7
8
9
10General initialization - Version: 1.0.0
11
12High speed PHY - Version: 0.1.1 (COM-PHY-V20)
13
14USB2 UTMI PHY initialized succesfully
15
16USB2 UTMI PHY initialized succesfully
17
18High speed PHY - Ended Successfully
19
20
21DDR3 Training Sequence - Ver 5.7.1
22
23DDR3 Training Sequence - Run with PBS.
24
25DDR3 Training Sequence - Ended Successfully
26
27BootROM: Image checksum verification PASSED
28
29
30 ** LOADER **
31
32
33U-Boot 2013.01_v1.03 (Nov 20 2014 - 16:39:45) Marvell version: 2014_T2.0p3
34
35Board: WD_Glacier_DB-88F6720-V2
36SoC: MV88F6720 Rev A0
37 running 2 CPUs
38CPU: ARM Cortex A9 MPCore (Rev 1) LE
39 CPU 0
40 CPU @ 800 [MHz]
41 L2 @ 400 [MHz]
42 TClock @ 200 [MHz]
43 DDR @ 534 [MHz]
44 DDR 16Bit Width, FastPath Memory Access, DLB Enabled
45DRAM: 512 MiB
46
47Map: Code:0x1fed6000:0x1ff92c90
48 BSS:0x1ffefa20
49 Stack:0x1f9c5f20
50 Heap:0x1f9c6000:0x1fed6000
51
52SF: Detected MX25L8006E with page size 64 KiB, total 1 MiB
53PCI-e 0: Detected No Link.
54PCI-e 1: Detected No Link.
55SF: Detected MX25L8006E with page size 64 KiB, total 1 MiB
56MAC addr: 00:90:A9:E9:64:60
57### Loading Firmware from USB 3.0 Disk ###
58USB2.0 0: Host Mode
59USB2.0 1: Device Mode
60USB3.0 0: Host Mode
61Board configuration detected:
62GE-PHY-0 on MAC0
63SERDES configuration:
64Lane #0: PCIe0
65Lane #1: PCIe1
66Lane #2: SATA0
67Lane #3: USB3
68Net: egiga0 [PRIME]
69*** ERROR: ping address not given
70Hit any key to stop autoboot: 2 0
71Marvell>> setenv usbActive 1
72Marvell>> setenv usbType 2
73Marvell>> usb start
74(Re)start USB...
75USB0: Port (usbActive) : 1Interface (usbType = 2) : USB EHCI 1.00
76scanning bus 0 for devices... 2 USB Device(s) found
77 scanning usb for storage devices... 1 Storage Device(s) found
78Marvell>>
79(Re)start USB...
80USB0: Port (usbActive) : 1Interface (usbType = 2) : USB EHCI 1.00
81scanning bus 0 for devices... 2 USB Device(s) found
82 scanning usb for storage devices... 1 Storage Device(s) found
83Marvell>> fatload usb 0:1 0xa00000 boot/uImage
84reading boot/uImage
855197303 bytes read in 507 ms (9.8 MiB/s)
86Marvell>> fatload usb 0:1 0x2000000 boot/uRamdisk
87reading boot/uRamdisk
889421927 bytes read in 881 ms (10.2 MiB/s)
89Marvell>> setenv bootargs root=/dev/sda3 console=ttyS0,115200
90Marvell>> bootm 0xa00000 0x2000000
91## Booting image at 00a00000 ...
92## Booting kernel from Legacy Image at 00a00000 ...
93 Image Name: Linux-5.3.5-mvebu-tld-1
94 Created: 2020-01-31 23:39:47 UTC
95 Image Type: ARM Linux Kernel Image (uncompressed)
96 Data Size: 5197239 Bytes = 5 MiB
97 Load Address: 00008000
98 Entry Point: 00008000
99 Verifying Checksum ... OK
100## Loading init Ramdisk from Legacy Image at 02000000 ...
101 Image Name: initramfs-5.3.5-mvebu-tld-1
102 Created: 2020-01-31 23:39:47 UTC
103 Image Type: ARM Linux RAMDisk Image (gzip compressed)
104 Data Size: 9421863 Bytes = 9 MiB
105 Load Address: 00000000
106 Entry Point: 00000000
107 Verifying Checksum ... OK
108 Loading Kernel Image ... OK
109OK
110
111Starting kernel ...
112
113Uncompressing Linux... done, booting the kernel.
114[ 0.000000][ T0] Booting Linux on physical CPU 0x0
115[ 0.000000][ T0] Linux version 5.3.5-mvebu-tld-1 (root@tldDebianVM) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1.0 SMP PREEMPT Tue Oct 8 21:03:08 PDT 2019
116[ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
117[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
118[ 0.000000][ T0] OF: fdt: Machine model: WD MyCloud Gen2
119[ 0.000000][ T0] Memory policy: Data cache writealloc
120[ 0.000000][ T0] percpu: Embedded 20 pages/cpu s51020 r8192 d22708 u81920
121[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048
122[ 0.000000][ T0] Kernel command line: root=/dev/sda3 console=ttyS0,115200
123[ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
124[ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
125[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
126[ 0.000000][ T0] Memory: 494808K/524288K available (10240K kernel code, 854K rwdata, 2768K rodata, 1024K init, 342K bss, 29480K reserved, 0K cma-reserved, 0K highmem)
127[ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x30c/0x830 with crng_init=0
128[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
129[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
130[ 0.000000][ T0] Tasks RCU enabled.
131[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
132[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
133[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
134[ 0.000000][ T0] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
135[ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9
136[ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9
137[ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines
138[ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled
139[ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 8 ways, 256 kB
140[ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56040001
141[ 0.000000][ T0] Switching to timer-based delay loop, resolution 40ns
142[ 0.000006][ T0] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
143[ 0.000022][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
144[ 0.000758][ T0] Console: colour dummy device 80x30
145[ 0.000796][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
146[ 0.000811][ T0] pid_max: default: 32768 minimum: 301
147[ 0.001042][ T0] LSM: Security Framework initializing
148[ 0.001138][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
149[ 0.001152][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
150[ 0.001898][ T0] *** VALIDATE proc ***
151[ 0.002105][ T0] *** VALIDATE cgroup1 ***
152[ 0.002120][ T0] *** VALIDATE cgroup2 ***
153[ 0.002203][ T0] CPU: Testing write buffer coherency: ok
154[ 0.002242][ T0] CPU0: Spectre v2: using BPIALL workaround
155[ 0.002546][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
156[ 0.059965][ T1] Setting up static identity map for 0x100000 - 0x100060
157[ 0.060344][ T1] mvebu-soc-id: MVEBU SoC ID=0x6720, Rev=0x3
158[ 0.079962][ T1] rcu: Hierarchical SRCU implementation.
159[ 0.120070][ T1] smp: Bringing up secondary CPUs ...
160[ 0.200458][ T1] Booting CPU 1
161[ 0.200668][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
162[ 0.200676][ T0] CPU1: Spectre v2: using BPIALL workaround
163[ 0.200843][ T1] smp: Brought up 1 node, 2 CPUs
164[ 0.200857][ T1] SMP: Total of 2 processors activated (100.00 BogoMIPS).
165[ 0.200867][ T1] CPU: All CPU(s) started in SVC mode.
166[ 0.201810][ T1] devtmpfs: initialized
167[ 0.205160][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
168[ 0.205781][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
169[ 0.205824][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
170[ 0.206151][ T1] xor: measuring software checksum speed
171[ 0.300549][ T1] arm4regs : 1258.800 MB/sec
172[ 0.400824][ T1] 8regs : 951.600 MB/sec
173[ 0.501093][ T1] 32regs : 1006.800 MB/sec
174[ 0.501104][ T1] xor: using function: arm4regs (1258.800 MB/sec)
175[ 0.501118][ T1] prandom: seed boundary self test passed
176[ 0.503732][ T1] prandom: 100 self tests passed
177[ 0.503741][ T1] pinctrl core: initialized pinctrl subsystem
178[ 0.505583][ T1] NET: Registered protocol family 16
179[ 0.506685][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
180[ 0.507502][ T1] audit: initializing netlink subsys (disabled)
181[ 0.507727][ T33] audit: type=2000 audit(0.500:1): state=initialized audit_enabled=0 res=1
182[ 0.509802][ T1] cpuidle: using governor ladder
183[ 0.509845][ T1] cpuidle: using governor menu
184[ 0.510039][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
185[ 0.510053][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes.
186[ 0.731985][ T1] raid6: int32x8 gen() 133 MB/s
187[ 0.902333][ T1] raid6: int32x8 xor() 104 MB/s
188[ 1.072772][ T1] raid6: int32x4 gen() 130 MB/s
189[ 1.243286][ T1] raid6: int32x4 xor() 110 MB/s
190[ 1.413797][ T1] raid6: int32x2 gen() 145 MB/s
191[ 1.584092][ T1] raid6: int32x2 xor() 144 MB/s
192[ 1.754500][ T1] raid6: int32x1 gen() 128 MB/s
193[ 1.925003][ T1] raid6: int32x1 xor() 135 MB/s
194[ 1.925013][ T1] raid6: using algorithm int32x2 gen() 145 MB/s
195[ 1.925022][ T1] raid6: .... xor() 144 MB/s, rmw enabled
196[ 1.925030][ T1] raid6: using intx1 recovery algorithm
197[ 1.926333][ T1] vgaarb: loaded
198[ 1.927256][ T1] SCSI subsystem initialized
199[ 1.928468][ T1] usbcore: registered new interface driver usbfs
200[ 1.928619][ T1] usbcore: registered new interface driver hub
201[ 1.928788][ T1] usbcore: registered new device driver usb
202[ 1.929878][ T1] mc: Linux media interface: v0.10
203[ 1.930015][ T1] videodev: Linux video capture interface: v2.00
204[ 1.930495][ T1] pps_core: LinuxPPS API ver. 1 registered
205[ 1.930510][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
206[ 1.930613][ T1] PTP clock support registered
207[ 1.932888][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource
208[ 2.877728][ T1] VFS: Disk quotas dquot_6.6.0
209[ 2.877829][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
210[ 2.894714][ T1] thermal_sys: Registered thermal governor 'step_wise'
211[ 2.895116][ T1] NET: Registered protocol family 2
212[ 2.895881][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
213[ 2.895924][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
214[ 2.895996][ T1] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
215[ 2.896066][ T1] TCP: Hash tables configured (established 4096 bind 4096)
216[ 2.896173][ T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
217[ 2.896206][ T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
218[ 2.896545][ T1] NET: Registered protocol family 1
219[ 2.897237][ T1] RPC: Registered named UNIX socket transport module.
220[ 2.897252][ T1] RPC: Registered udp transport module.
221[ 2.897261][ T1] RPC: Registered tcp transport module.
222[ 2.897269][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
223[ 2.897285][ T1] PCI: CLS 0 bytes, default 64
224[ 2.897525][ T1] Trying to unpack rootfs image as initramfs...
225[ 3.502644][ T1] Freeing initrd memory: 9204K
226[ 3.502756][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
227[ 3.503156][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
228[ 3.506591][ T1] Initialise system trusted keyrings
229[ 3.506648][ T1] Key type blacklist registered
230[ 3.506822][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0
231[ 3.506981][ T1] zbud: loaded
232[ 3.508393][ T1] NFS: Registering the id_resolver key type
233[ 3.508426][ T1] Key type id_resolver registered
234[ 3.508436][ T1] Key type id_legacy registered
235[ 3.508457][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
236[ 3.508473][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
237[ 3.508965][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
238[ 3.509874][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
239[ 3.510054][ T1] orangefs_init: module version upstream loaded
240[ 3.557500][ T1] async_tx: api initialized (async)
241[ 3.557525][ T1] Key type asymmetric registered
242[ 3.557535][ T1] Asymmetric key parser 'x509' registered
243[ 3.557720][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
244[ 3.561197][ T1] armada-375-pinctrl f1018000.pinctrl: registered pinctrl driver
245[ 3.566980][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
246[ 3.623836][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
247[ 3.626443][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
248[ 3.683843][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
249[ 3.792593][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
250[ 3.795882][ T1] printk: console [ttyS0] disabled
251[ 3.816083][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 24, base_baud = 12500000) is a 16550A
252[ 4.713847][ T1] printk: console [ttyS0] enabled
253[ 4.721455][ T1] sata_mv f10a0000.sata: slots 32 ports 1
254[ 4.728378][ T1] scsi host0: sata_mv
255[ 4.732751][ T1] ata1: SATA max UDMA/133 irq 43
256[ 4.739472][ T1] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
257[ 4.745053][ T1] 1 fixed-partitions partitions found on MTD device spi0.0
258[ 4.752140][ T1] Creating 1 MTD partitions on "spi0.0":
259[ 4.757678][ T1] 0x000000000000-0x000000100000 : "u-boot"
260[ 4.766443][ T1] libphy: Fixed MDIO Bus: probed
261[ 4.772101][ T1] libphy: orion_mdio_bus: probed
262[ 4.796928][ T1] mvpp2 f10f0000.ethernet eth0: Using hardware mac address 00:00:00:00:00:04
263[ 4.841568][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
264[ 4.848894][ T1] ehci-pci: EHCI PCI platform driver
265[ 4.854164][ T1] ehci-orion: EHCI orion driver
266[ 4.859159][ T1] orion-ehci f1054000.usb: EHCI Host Controller
267[ 4.865339][ T1] orion-ehci f1054000.usb: new USB bus registered, assigned bus number 1
268[ 4.873775][ T1] orion-ehci f1054000.usb: irq 39, io mem 0xf1054000
269[ 4.902934][ T1] orion-ehci f1054000.usb: USB 2.0 started, EHCI 1.00
270[ 4.909849][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
271[ 4.918889][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
272[ 4.926864][ T1] usb usb1: Product: EHCI Host Controller
273[ 4.932468][ T1] usb usb1: Manufacturer: Linux 5.3.5-mvebu-tld-1 ehci_hcd
274[ 4.939563][ T1] usb usb1: SerialNumber: f1054000.usb
275[ 4.945579][ T1] hub 1-0:1.0: USB hub found
276[ 4.950099][ T1] hub 1-0:1.0: 1 port detected
277[ 4.955965][ T1] xhci-hcd f1058000.usb3: xHCI Host Controller
278[ 4.962037][ T1] xhci-hcd f1058000.usb3: new USB bus registered, assigned bus number 2
279[ 4.970418][ T1] xhci-hcd f1058000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
280[ 4.980456][ T1] xhci-hcd f1058000.usb3: irq 40, io mem 0xf1058000
281[ 4.987305][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
282[ 4.996388][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
283[ 5.004368][ T1] usb usb2: Product: xHCI Host Controller
284[ 5.009971][ T1] usb usb2: Manufacturer: Linux 5.3.5-mvebu-tld-1 xhci-hcd
285[ 5.017067][ T1] usb usb2: SerialNumber: f1058000.usb3
286[ 5.023184][ T1] hub 2-0:1.0: USB hub found
287[ 5.027707][ T1] hub 2-0:1.0: 1 port detected
288[ 5.032784][ T1] xhci-hcd f1058000.usb3: xHCI Host Controller
289[ 5.038882][ T1] xhci-hcd f1058000.usb3: new USB bus registered, assigned bus number 3
290[ 5.047162][ T1] xhci-hcd f1058000.usb3: Host supports USB 3.0 SuperSpeed
291[ 5.054353][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
292[ 5.063452][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.03
293[ 5.072460][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
294[ 5.080440][ T1] usb usb3: Product: xHCI Host Controller
295[ 5.086056][ T1] usb usb3: Manufacturer: Linux 5.3.5-mvebu-tld-1 xhci-hcd
296[ 5.093152][ T1] usb usb3: SerialNumber: f1058000.usb3
297[ 5.099209][ T1] hub 3-0:1.0: USB hub found
298[ 5.103762][ T1] hub 3-0:1.0: 1 port detected
299[ 5.109105][ T1] usbcore: registered new interface driver usblp
300[ 5.115492][ T1] usbcore: registered new interface driver usb-storage
301[ 5.122635][ T1] mousedev: PS/2 mouse device common for all mice
302[ 5.130002][ T1] rtc-mv f1010300.rtc: registered as rtc0
303[ 5.136245][ T1] i2c /dev entries driver
304[ 5.232957][ T1213] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
305[ 5.242285][ T1213] ata1.00: LPM support broken, forcing max_power
306[ 5.248683][ T1213] ata1.00: ATA-6: WDC WD800JD-22JNC0, 05.01C05, max UDMA/133
307[ 5.256601][ T1] watchdog: f1020300.watchdog: driver supplied timeout (4294967295) out of range
308[ 5.263112][ T1213] ata1.00: 156301488 sectors, multi 0: LBA
309[ 5.266078][ T1] watchdog: f1020300.watchdog: falling back to default timeout (171)
310[ 5.273996][ T1213] ata1.00: LPM support broken, forcing max_power
311[ 5.285833][ T1213] ata1.00: configured for UDMA/133
312[ 5.291019][ T1] orion_wdt: Initial timeout 171 sec
313[ 5.296978][ T1] device-mapper: uevent: version 1.0.3
314[ 5.301448][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD800JD-22JN 1C05 PQ: 0 ANSI: 5
315[ 5.311473][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
316[ 5.312589][ T7] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
317[ 5.329269][ T7] sd 0:0:0:0: [sda] Write Protect is off
318[ 5.334850][ T1329] usb 1-1: new high-speed USB device number 2 using orion-ehci
319[ 5.342422][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
320[ 5.349813][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
321[ 5.349851][ T7] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
322[ 5.357217][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
323[ 5.374592][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
324[ 5.381428][ T1] device-mapper: raid: Loading target version 1.14.0
325[ 5.408931][ T7] sda: sda1 sda2 sda3
326[ 5.414911][ T7] sd 0:0:0:0: [sda] Attached SCSI disk
327[ 5.518920][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
328[ 5.527583][ T1] hidraw: raw HID events driver (C) Jiri Kosina
329[ 5.534563][ T1] usbcore: registered new interface driver usbhid
330[ 5.540871][ T1] usbhid: USB HID core driver
331[ 5.543999][ T1329] usb 1-1: New USB device found, idVendor=1976, idProduct=6025, bcdDevice= 1.00
332[ 5.546089][ T1] drop_monitor: Initializing network drop monitor service
333[ 5.554632][ T1329] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
334[ 5.562006][ T1] NET: Registered protocol family 10
335[ 5.569348][ T1329] usb 1-1: Product: Flash Disk
336[ 5.579200][ T1329] usb 1-1: SerialNumber: 123456789003763
337[ 5.579675][ T1] Segment Routing with IPv6
338[ 5.585670][ T1329] usb-storage 1-1:1.0: USB Mass Storage device detected
339[ 5.589423][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
340[ 5.603078][ T1329] scsi host1: usb-storage 1-1:1.0
341[ 5.604878][ T1] NET: Registered protocol family 17
342[ 5.613755][ T1] 8021q: 802.1Q VLAN Support v1.8
343[ 5.618728][ T1] Key type dns_resolver registered
344[ 5.623857][ T1] ThumbEE CPU extension supported.
345[ 5.628857][ T1] Registering SWP/SWPB emulation handler
346[ 5.635514][ T1] registered taskstats version 1
347[ 5.640340][ T1] Loading compiled-in X.509 certificates
348[ 5.646025][ T1] zswap: loaded using pool lzo/zbud
349[ 5.712714][ T1] Key type big_key registered
350[ 5.747442][ T1] Key type encrypted registered
351[ 5.756337][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0
352[ 5.764446][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-01-31T23:51:50 UTC (1580514710)
353[ 5.777185][ T1] Freeing unused kernel memory: 1024K
354[ 5.813604][ T1] Checked W+X mappings: passed, no W+X pages found
355[ 5.819999][ T1] Run /init as init process
356Loading, please wait...
357Starting version 241
358[ 6.594139][ T1489] usbcore: registered new interface driver uas
359[ 6.654135][ T1382] scsi 1:0:0:0: Direct-Access Flash Disk 5.00 PQ: 0 ANSI: 2
360[ 6.670238][ T20] sd 1:0:0:0: [sdb] 257792 512-byte logical blocks: (132 MB/126 MiB)
361[ 6.681900][ T20] sd 1:0:0:0: [sdb] Write Protect is off
362[ 6.693240][ T20] sd 1:0:0:0: [sdb] No Caching mode page found
363[ 6.703330][ T20] sd 1:0:0:0: [sdb] Assuming drive cache: write through
364[ 6.721274][ T20] sdb: sdb1
365[ 6.728204][ T20] sd 1:0:0:0: [sdb] Attached SCSI removable disk
366[ 7.190861][ C0] random: fast init done
367Begin: Loading essential drivers ... done.
368Begin: Running /scripts/init-premount ... done.
369Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
370Begin: Running /scripts/local-premount ... done.
371Begin: Will now check root file system ... fsck from util-linux 2.33.1
372[/sbin/fsck.ext4 (1) -- /dev/sda3] fsck.ext4 -a -C0 /dev/sda3
373/dev/sda3: clean, 44049/183264 files, 664739/732416 blocks
374done.
375[ 7.733150][ T1522] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
376done.
377Begin: Running /scripts/local-bottom ... done.
378Begin: Running /scripts/init-bottom ... done.
379[ 8.928592][ T1] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
380[ 8.956194][ T1] systemd[1]: Detected architecture arm.
381
382Welcome to Debian GNU/Linux 10 (buster)!
383
384[ 9.020435][ T1] systemd[1]: Set hostname to <wdmc>.
385[ 9.044246][ T1] systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument
386[ 9.291214][ T1540] systemd-fstab-generator[1540]: Ignoring "noauto" for root device
387[ 10.184434][ T1] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
388[ 10.202355][ T1] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
389[ 10.697377][ T1] random: systemd: uninitialized urandom read (16 bytes read)
390[ 10.711394][ T1] random: systemd: uninitialized urandom read (16 bytes read)
391[ 10.719240][ T1] systemd[1]: Listening on initctl Compatibility Named Pipe.
392[ OK ] Listening on initctl Compatibility Named Pipe.
393[ 10.763128][ T1] random: systemd: uninitialized urandom read (16 bytes read)
394[ 10.770825][ T1] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
395[ OK ] Started Forward Password Ruests to Wall Directory Watch.
396[ 10.814248][ T1] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
397[ OK ] Set up automount Arbitrarys File System Automount Point.
398[ 10.853770][ T1] systemd[1]: Listening on Journal Socket (/dev/log).
399[ OK ] Listening on Journal Socket (/dev/log).
400[ OK ] Listening on Journal Socket.
401 Starting Load Kernel Modules...
402[ OK ] Listening on Syslog Socket.
403 Mounting POSIX Message Queue File System...
404 Mounting Kernel Debug File System...
405[ OK ] Listening on udev Kernel Socket.
406[ OK ] Created slice system-serial\x2dgetty.slice.
407[ OK ] Listening on fsck to fsckd communication Socket.
408[ OK ] Created slice system-getty.slice.
409[ OK ] Reached target Remote File Systems.
410[ OK ] Started Dispatch Password ts to Console Directory Watch.
411[ OK ] Reached target Local Encrypted Volumes.
412 Starting Create list of reodes for the current kernel...
413[ OK ] Reached target Paths.
414 Starting Remount Root and Kernel File Systems...
415[ OK ] Created slice User and Session Slice.
416[ OK ] Reached target Slices.
417[ OK ] Listening on udev Control Socket.
418[ 11.431793][ T1556] devpts: called with bogus options
419 Starting udev Coldplug all Devices...
420[ 11.473214][ T1554] EXT4-fs (sda3): re-mounted. Opts: (null)
421[ OK ] Listening on Journal Audit Socket.
422 Starting Journal Service...
423[ OK ] Started Load Kernel Modules.
424[ OK ] Mounted POSIX Message Queue File System.
425[ OK ] Mounted Kernel Debug File System.
426[ OK ] Started Create list of req nodes for the current kernel.
427[FAILED] Failed to start Remount Root and Kernel File Systems.
428See 'systemctl status systemd-remount-fs.service' for details.
429[ OK ] Started Journal Service.
430 Starting Load/Save Random Seed...
431 Starting Create System Users...
432 Starting Flush Journal to Persistent Storage...
433 Starting Apply Kernel Variables...
434[ OK ] Started Load/Save Random Seed.
435[ 11.977830][ T1561] systemd-journald[1561]: Received request to flush runtime journal from PID 1
436[ OK ] Started Apply Kernel Variables.
437[ OK ] Started Create System Users.
438[ OK ] Started Flush Journal to Persistent Storage.
439 Starting Create Static Device Nodes in /dev...
440[ OK ] Started Create Static Device Nodes in /dev.
441 Starting udev Kernel Device Manager...
442[ OK ] Reached target Local File Systems (Pre).
443[ OK ] Started udev Coldplug all Devices.
444 Starting Helper to synchronize boot up for ifupdown...
445[ OK ] Started udev Kernel Device Manager.
446[ OK ] Found device /dev/ttyS0.
447[ 13.113117][ T1579] sd 0:0:0:0: Attached scsi generic sg0 type 0
448[ 13.124094][ T1579] sd 1:0:0:0: Attached scsi generic sg1 type 0
449[ 14.219379][ C0] random: crng init done
450[ 14.223516][ C0] random: 7 urandom warning(s) missed due to ratelimiting
451[ OK ] Found device /sys/subsystem/net/devices/eth0.
452[ OK ] Found device WDC_WD800JD-22JNC0 primary.
453[ OK ] Started Helper to synchronize boot up for ifupdown.
454[ OK ] Found device WDC_WD800JD-22JNC0 primary.
455 Mounting /home...
456 Activating swap /dev/sda1...
457[ 18.193307][ T1617] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
458[ OK ] Mounted /home.
459[ 18.262945][ T1618] Adding 975868k swap on /dev/sda1. Priority:-2 extents:1 across:975868k FS
460[ OK ] Activated swap /dev/sda1.
461[ OK ] Reached target Swap.
462 Mounting /tmp...
463[ OK ] Mounted /tmp.
464[ OK ] Reached target Local File Systems.
465 Starting Raise network interfaces...
466 Starting Create Volatile Files and Directories...
467[ OK ] Started ifup for eth0.
468[ OK ] Started Create Volatile Files and Directories.
469 Starting Update UTMP about System Boot/Shutdown...
470 Starting Network Time Synchronization...
471[ OK ] Started Update UTMP about System Boot/Shutdown.
472[ OK ] Started Network Time Synchronization.
473[ OK ] Reached target System Initialization.
474[ OK ] Started Daily Cleanup of Temporary Directories.
475[ 19.147414][ T1659] mvpp2 f10f0000.ethernet eth0: PHY [f10c0054.mdio-mii:00] driver [Generic PHY]
476[ 19.156477][ T1659] mvpp2 f10f0000.ethernet eth0: configuring for phy/rgmii-id link mode
477[ OK ] Listening on D-Bus System Message Bus Socket.
478[ OK ] Reached target Sockets.
479[ OK ] Reached target Basic System.
480 Starting Deferred execution scheduler...
481 Starting System Logging Service...
482[ OK ] Started Regular background program processing daemon.
483[ OK ] Started D-Bus System Message Bus.
484 Starting Login Service...
485[ OK ] Reached target System Time Synchronized.
486[ OK ] Started Daily man-db regeneration.
487[ OK ] Started Daily apt download activities.
488[ OK ] Started Daily rotation of log files.
489[ OK ] Started Daily apt upgrade and clean activities.
490[ OK ] Reached target Timers.
491[ OK ] Started System Logging Service.
492[ OK ] Started Deferred execution scheduler.
493[ OK ] Started Login Service.
494[ 22.253708][ T1661] mvpp2 f10f0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
495[ 22.262388][ T1661] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
496[ *** ] A start job is running for Raise network interfaces (16s / 5min 7s)
497[ OK ] Started Raise network interfaces.
498[ OK ] Reached target Network.
499[ OK ] Reached target Network is Online.
500 Starting LSB: exim Mail Transport Agent...
501 Starting /etc/rc.local Compatibility...
502 Starting Permit User Sessions...
503 Starting OpenBSD Secure Shell server...
504[ OK ] Started /etc/rc.local Compatibility.
505[ OK ] Started Permit User Sessions.
506[ OK ] Started Getty on tty1.
507[ OK ] Started Serial Getty on ttyS0.
508[ OK ] Reached target Login Prompts.
509[ OK ] Started OpenBSD Secure Shell server.
510[ OK ] Started LSB: exim Mail Transport Agent.
511[ OK ] Reached target Multi-User System.
512[ OK ] Reached target Graphical Interface.
513 Starting Update UTMP about System Runlevel Changes...
514[ OK ] Started Update UTMP about System Runlevel Changes.
515[ 29.266239][ T1709] fbcon: Taking over console
516
517
518Debian GNU/Linux 10 wdmc ttyS0
519
520wdmc login: root
521
522Password:
523Last login: Fri Jan 31 23:43:48 UTC 2020 on ttyS0
524Linux wdmc 5.3.5-mvebu-tld-1 #1.0 SMP PREEMPT Tue Oct 8 21:03:08 PDT 2019 armv7l
525
526The programs included with the Debian GNU/Linux system are free software;
527the exact distribution terms for each program are described in the
528individual files in /usr/share/doc/*/copyright.
529
530Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
531permitted by applicable law.
532root@wdmc:~# fw_printenv
533bootdelay=2
534baudrate=115200
535stdin=serial,cros-ec-keyb,usbkbd
536stdout=serial,vidconsole
537stderr=serial,vidconsole
538ethaddr=00:00:11:22:33:44
539eth1addr=00:00:11:22:33:45
540eth3addr=00:00:11:22:33:46
541eth5addr=00:00:11:22:33:47
542ipaddr=1.2.3.4
543host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi
544sata_boot=if sata dev ${devnum}; then setenv devtype sata; run scan_dev_for_boot_part; fi
545scsi_init=if ${scsi_need_init}; then setenv scsi_need_init false; scsi scan; fi
546scsi_boot=run scsi_init; if scsi dev ${devnum}; then setenv devtype scsi; run scan_dev_for_boot_part; fi
547virtio_boot=if virtio dev ${devnum}; then setenv devtype virtio; run scan_dev_for_boot_part; fi
548boot_prefixes=/ /boot/
549boot_scripts=boot.scr.uimg boot.scr
550boot_script_dhcp=boot.scr.uimg
551boot_targets=host1 host0
552boot_syslinux_conf=extlinux/extlinux.conf
553boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf}
554scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
555boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
556scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
557scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;
558scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done
559bootcmd_host1=setenv devnum 1; run host_boot
560bootcmd_host0=setenv devnum 0; run host_boot
561distro_bootcmd=setenv scsi_need_init; for target in ${boot_targets}; do run bootcmd_${target}; done
562bootm_size=0x10000000
563kernel_addr_r=0x1000000
564fdt_addr_r=0xc00000
565ramdisk_addr_r=0x2000000
566scriptaddr=0x1000
567pxefile_addr_r=0x2000
568bootargs=root=/dev/sda3 console=ttyS0,115200
569bootcmd=printenv
570root@wdmc:~# cat /proc/mtd
571dev: size erasesize name
572mtd0: 00100000 00010000 "u-boot"
573root@wdmc:~# cat /etc/fw_env.config
574# MTD device name Device offset Env. size Flash sector size Number of sectors
575/dev/mtd0 0xf0000 0x10000 0x10000 1
576root@wdmc:~#