· 6 years ago · Sep 12, 2019, 05:46 PM
1[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
2[ 0.000000] Linux version 5.3.0-rc6-next-20190830-g4fe25a02c4f1-sigmaris (root@rp64builder) (gcc version 8.3.0 (Debian 8.3.0-2)) #sigmaris SMP PREEMPT Sun Sep 1 16:50:21 BST 2019
3[ 0.000000] Machine model: Pine64 RockPro64
4[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000ff1a0000 (options '')
5[ 0.000000] printk: bootconsole [uart8250] enabled
6[ 0.000000] cma: Reserved 16 MiB at 0x00000000f7000000
7[ 0.000000] NUMA: No NUMA configuration found
8[ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000f7ffffff]
9[ 0.000000] NUMA: NODE_DATA [mem 0xf67ed800-0xf67eefff]
10[ 0.000000] Zone ranges:
11[ 0.000000] DMA32 [mem 0x0000000000200000-0x00000000f7ffffff]
12[ 0.000000] Normal empty
13[ 0.000000] Movable zone start for each node
14[ 0.000000] Early memory node ranges
15[ 0.000000] node 0: [mem 0x0000000000200000-0x00000000f7ffffff]
16[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff]
17[ 0.000000] On node 0 totalpages: 1015296
18[ 0.000000] DMA32 zone: 15864 pages used for memmap
19[ 0.000000] DMA32 zone: 0 pages reserved
20[ 0.000000] DMA32 zone: 1015296 pages, LIFO batch:63
21[ 0.000000] psci: probing for conduit method from DT.
22[ 0.000000] psci: PSCIv1.0 detected in firmware.
23[ 0.000000] psci: Using standard PSCI v0.2 function IDs
24[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
25[ 0.000000] psci: SMC Calling Convention v1.0
26[ 0.000000] percpu: Embedded 22 pages/cpu s50264 r8192 d31656 u90112
27[ 0.000000] pcpu-alloc: s50264 r8192 d31656 u90112 alloc=22*4096
28[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5
29[ 0.000000] Detected VIPT I-cache on CPU0
30[ 0.000000] CPU features: detected: ARM erratum 845719
31[ 0.000000] CPU features: detected: GIC system register CPU interface
32[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 999432
33[ 0.000000] Policy zone: DMA32
34[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 console=ttyS2,1500000n8 rw panic=10 init=/sbin/init coherent_pool=1M ethaddr=66:3c:f2:aa:d9:ab eth1addr= serial=5b91b24c2afec3a cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 root=/dev/nfs rootfstype=nfs nfsroot=10.0.0.102:/mnt/store1/rp64buster rootwait
35[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
36[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
37[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
38[ 0.000000] Memory: 3938200K/4061184K available (13694K kernel code, 914K rwdata, 5032K rodata, 896K init, 440K bss, 106600K reserved, 16384K cma-reserved)
39[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
40[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
41[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
42[ 0.000000] Tasks RCU enabled.
43[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
44[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
45[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
46[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
47[ 0.000000] GICv3: 988 SPIs implemented
48[ 0.000000] GICv3: 0 Extended SPIs implemented
49[ 0.000000] GICv3: Distributor has no Range Selector support
50[ 0.000000] GICv3: 16 PPIs implemented
51[ 0.000000] GICv3: no VLPI support, no direct LPI support
52[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
53[ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
54[ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @f1480000 (flat, esz 8, psz 64K, shr 0)
55[ 0.000000] ITS: using cache flushing for cmd queue
56[ 0.000000] GICv3: using LPI property table @0x00000000f1440000
57[ 0.000000] GIC: using cache flushing for LPI property table
58[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000000f1450000
59[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
60[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
61[ 0.000000] random: get_random_bytes called from start_kernel+0x2f0/0x47c with crng_init=0
62[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
63[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
64[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
65[ 0.001838] Console: colour dummy device 80x25
66[ 0.002399] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
67[ 0.003363] pid_max: default: 32768 minimum: 301
68[ 0.003923] LSM: Security Framework initializing
69[ 0.004452] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
70[ 0.005165] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
71[ 0.030431] ASID allocator initialised with 32768 entries
72[ 0.038421] rcu: Hierarchical SRCU implementation.
73[ 0.046569] Platform MSI: interrupt-controller@fee20000 domain created
74[ 0.047585] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
75[ 0.054480] smp: Bringing up secondary CPUs ...
76[ 0.086692] Detected VIPT I-cache on CPU1
77[ 0.086732] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
78[ 0.086747] GICv3: CPU1: using allocated LPI pending table @0x00000000f1460000
79[ 0.086794] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
80[ 0.118764] Detected VIPT I-cache on CPU2
81[ 0.118794] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
82[ 0.118807] GICv3: CPU2: using allocated LPI pending table @0x00000000f1470000
83[ 0.118841] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
84[ 0.150856] Detected VIPT I-cache on CPU3
85[ 0.150884] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
86[ 0.150897] GICv3: CPU3: using allocated LPI pending table @0x00000000f1500000
87[ 0.150928] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
88[ 0.185646] CPU features: detected: EL2 vector hardening
89[ 0.185968] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware
90[ 0.186348] Detected PIPT I-cache on CPU4
91[ 0.187558] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
92[ 0.188010] GICv3: CPU4: using allocated LPI pending table @0x00000000f1510000
93[ 0.189219] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
94[ 0.229369] Detected PIPT I-cache on CPU5
95[ 0.230551] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
96[ 0.230973] GICv3: CPU5: using allocated LPI pending table @0x00000000f1520000
97[ 0.232029] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
98[ 0.237063] smp: Brought up 1 node, 6 CPUs
99[ 0.250112] SMP: Total of 6 processors activated.
100[ 0.250571] CPU features: detected: 32-bit EL0 Support
101[ 0.251066] CPU features: detected: CRC32 instructions
102[ 0.462292] CPU: All CPU(s) started at EL2
103[ 0.463433] alternatives: patching kernel code
104[ 0.469634] devtmpfs: initialized
105[ 0.531723] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
106[ 0.535053] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
107[ 0.565171] xor: measuring software checksum speed
108[ 0.603203] 8regs : 44.000 MB/sec
109[ 0.643364] 32regs : 54.000 MB/sec
110[ 0.683526] arm64_neon: 47.000 MB/sec
111[ 0.684723] xor: using function: 32regs (54.000 MB/sec)
112[ 0.686494] pinctrl core: initialized pinctrl subsystem
113[ 0.721360] NET: Registered protocol family 16
114[ 0.836336] DMA: preallocated 1024 KiB pool for atomic allocations
115[ 0.840251] audit: initializing netlink subsys (disabled)
116[ 0.846148] audit: type=2000 audit(0.840:1): state=initialized audit_enabled=0 res=1
117[ 0.900675] cpuidle: using governor ladder
118[ 0.903467] cpuidle: using governor menu
119[ 0.927146] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
120[ 0.937390] Serial: AMBA PL011 UART driver
121[ 2.904938] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
122[ 2.906845] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
123[ 2.909002] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
124[ 2.910682] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
125[ 3.211815] cryptd: max_cpu_qlen set to 1000
126[ 3.726321] raid6: neonx8 gen() 25 MB/s
127[ 3.793042] raid6: neonx8 xor() 21 MB/s
128[ 3.860954] raid6: neonx4 gen() 22 MB/s
129[ 3.929834] raid6: neonx4 xor() 678 MB/s
130[ 3.998209] raid6: neonx2 gen() 20 MB/s
131[ 4.066142] raid6: neonx2 xor() 19 MB/s
132[ 4.136228] raid6: neonx1 gen() 12 MB/s
133[ 4.202861] raid6: neonx1 xor() 13 MB/s
134[ 4.274369] raid6: int64x8 gen() 16 MB/s
135[ 4.344505] raid6: int64x8 xor() 9 MB/s
136[ 4.412309] raid6: int64x4 gen() 14 MB/s
137[ 4.482983] raid6: int64x4 xor() 10 MB/s
138[ 4.550313] raid6: int64x2 gen() 10 MB/s
139[ 4.617429] raid6: int64x2 xor() 8 MB/s
140[ 4.692774] raid6: int64x1 gen() 6 MB/s
141[ 4.765551] raid6: int64x1 xor() 5 MB/s
142[ 4.767005] raid6: using algorithm neonx8 gen() 25 MB/s
143[ 4.768295] raid6: .... xor() 21 MB/s, rmw enabled
144[ 4.769477] raid6: using neon recovery algorithm
145[ 4.826410] vcc3v3_pcie: supplied by vcc12v_dcin
146[ 4.902755] vcc5v0_sys: supplied by vcc12v_dcin
147[ 4.919779] vcc5v0_usb: supplied by vcc12v_dcin
148[ 4.929360] vcc3v3_sys: supplied by vcc5v0_sys
149[ 4.945696] iommu: Default domain type: Translated
150[ 4.968785] rk_iommu ff650800.iommu: IRQ index 1 not found
151[ 4.986211] rk_iommu ff8f3f00.iommu: IRQ index 1 not found
152[ 5.002373] rk_iommu ff903f00.iommu: IRQ index 1 not found
153[ 5.018649] rk_iommu ff914000.iommu: IRQ index 1 not found
154[ 5.034546] rk_iommu ff924000.iommu: IRQ index 1 not found
155[ 5.047085] vgaarb: loaded
156[ 5.062891] SCSI subsystem initialized
157[ 5.068703] libata version 3.00 loaded.
158[ 5.080113] usbcore: registered new interface driver usbfs
159[ 5.083199] usbcore: registered new interface driver hub
160[ 5.088858] usbcore: registered new device driver usb
161[ 5.106129] mc: Linux media interface: v0.10
162[ 5.108442] videodev: Linux video capture interface: v2.00
163[ 5.114492] pps_core: LinuxPPS API ver. 1 registered
164[ 5.115778] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
165[ 5.118672] PTP clock support registered
166[ 5.134427] Advanced Linux Sound Architecture Driver Initialized.
167[ 5.157307] Bluetooth: Core ver 2.22
168[ 5.160435] NET: Registered protocol family 31
169[ 5.161613] Bluetooth: HCI device and connection manager initialized
170[ 5.163777] Bluetooth: HCI socket layer initialized
171[ 5.165163] Bluetooth: L2CAP socket layer initialized
172[ 5.166802] NetLabel: Initializing
173[ 5.168136] NetLabel: domain hash size = 128
174[ 5.169198] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
175[ 5.173291] NetLabel: unlabeled traffic allowed by default
176[ 5.203342] clocksource: Switched to clocksource arch_sys_counter
177[ 5.216920] VFS: Disk quotas dquot_6.6.0
178[ 5.221282] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
179[ 5.627406] thermal_sys: Registered thermal governor 'fair_share'
180[ 5.627617] thermal_sys: Registered thermal governor 'bang_bang'
181[ 5.629190] thermal_sys: Registered thermal governor 'step_wise'
182[ 5.630643] thermal_sys: Registered thermal governor 'power_allocator'
183[ 5.660092] NET: Registered protocol family 2
184[ 5.696646] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
185[ 5.703628] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
186[ 5.724817] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
187[ 5.764018] TCP: Hash tables configured (established 32768 bind 32768)
188[ 5.771700] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
189[ 5.780701] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
190[ 5.796373] NET: Registered protocol family 1
191[ 5.813741] RPC: Registered named UNIX socket transport module.
192[ 5.815896] RPC: Registered udp transport module.
193[ 5.817131] RPC: Registered tcp transport module.
194[ 5.818336] RPC: Registered tcp NFSv4.1 backchannel transport module.
195[ 5.820482] PCI: CLS 0 bytes, default 64
196[ 5.832729] Trying to unpack rootfs image as initramfs...
197[ 24.406301] Freeing initrd memory: 4968K
198[ 24.453573] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
199[ 24.473898] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
200[ 34.738062] workingset: timestamp_bits=44 max_order=20 bucket_order=0
201[ 35.146587] squashfs: version 4.0 (2009/01/31) Phillip Lougher
202[ 35.188436] NFS: Registering the id_resolver key type
203[ 35.190752] Key type id_resolver registered
204[ 35.192536] Key type id_legacy registered
205[ 35.194101] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
206[ 35.196216] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
207[ 35.256080] fuse: init (API version 7.31)
208[ 35.278659] 9p: Installing v9fs 9p2000 file system support
209[ 37.322068] NET: Registered protocol family 38
210[ 37.325004] Key type asymmetric registered
211[ 37.326188] Asymmetric key parser 'x509' registered
212[ 37.330198] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
213[ 37.337984] io scheduler mq-deadline registered
214[ 37.340496] io scheduler kyber registered
215[ 37.434436] vcc5v0_host: supplied by vcc5v0_usb
216[ 37.784882] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
217[ 37.787989] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
218[ 38.291871] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
219[ 38.302247] rockchip-pcie: probe of f8000000.pcie failed with error -110
220[ 38.408120] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
221[ 38.410224] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
222[ 38.485032] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
223[ 38.487743] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
224[ 38.514761] pwm-regulator: supplied by regulator-dummy
225[ 38.529364] vcc5v0_typec: supplied by vcc5v0_usb
226[ 38.712285] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
227[ 38.789575] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 38, base_baud = 1500000) is a 16550A
228[ 38.826528] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 39, base_baud = 1500000) is a 16550A
229[ 38.836433] printk: console [ttyS2] enabled
230[ 38.838293] printk: bootconsole [uart8250] disabled
231[ 38.939970] rockchip-vop ff8f0000.vop: Adding to iommu group 1
232[ 38.963460] rockchip-vop ff900000.vop: Adding to iommu group 2
233[ 39.186118] rockchip-drm display-subsystem: bound ff8f0000.vop (ops vop_component_ops)
234[ 39.221863] rockchip-drm display-subsystem: bound ff900000.vop (ops vop_component_ops)
235[ 39.228316] rockchip-drm display-subsystem: failed to bind ff940000.hdmi (ops dw_hdmi_rockchip_ops): -517
236[ 39.239767] rockchip-drm display-subsystem: master bind failed: -517
237[ 39.388840] cacheinfo: Unable to detect cache hierarchy for CPU 0
238[ 39.840367] brd: module loaded
239[ 40.279583] loop: module loaded
240[ 41.288934] spi-nor spi0.0: gd25q128 (16384 Kbytes)
241[ 41.740366] rockchip-spi ff1d0000.spi: chipselect 0 already in use
242[ 41.742020] spi_master spi0: spi_device register error /spi@ff1d0000/spi-flash@0
243[ 41.744257] spi_master spi0: Failed to create SPI device for /spi@ff1d0000/spi-flash@0
244[ 41.813628] libphy: Fixed MDIO Bus: probed
245[ 41.842063] tun: Universal TUN/TAP device driver, 1.6
246[ 41.928312] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
247[ 41.929569] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
248[ 41.933144] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k
249[ 41.934490] igb: Copyright (c) 2007-2014 Intel Corporation.
250[ 41.938139] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
251[ 41.940127] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
252[ 41.944012] sky2: driver version 1.30
253[ 41.989420] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
254[ 41.991580] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
255[ 41.997318] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
256[ 42.002770] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
257[ 42.005078] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
258[ 42.006422] rk_gmac-dwmac fe300000.ethernet: RX delay(0x20).
259[ 42.008348] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
260[ 42.012617] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
261[ 42.014055] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
262[ 42.021157] rk_gmac-dwmac fe300000.ethernet: init for RGMII
263[ 42.028157] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
264[ 42.029857] rk_gmac-dwmac fe300000.ethernet: DWMAC1000
265[ 42.032183] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
266[ 42.033702] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
267[ 42.035738] rk_gmac-dwmac fe300000.ethernet: COE Type 2
268[ 42.036898] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
269[ 42.038288] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
270[ 42.041226] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
271[ 42.042499] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
272[ 42.044254] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
273[ 42.942075] libphy: stmmac: probed
274[ 42.944141] RTL8211F Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
275[ 42.946480] RTL8211F Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
276[ 43.016928] usbcore: registered new interface driver cdc_ether
277[ 43.020360] usbcore: registered new interface driver cdc_eem
278[ 43.024209] usbcore: registered new interface driver cdc_ncm
279[ 43.034528] VFIO - User Level meta-driver version: 0.3
280[ 43.104084] OF: graph: no port node found in /syscon@ff770000/usb2-phy@e450/otg-port
281[ 43.105989] dwc3 fe800000.dwc3: IRQ otg not found
282[ 43.107748] dwc3 fe800000.dwc3: IRQ dwc_usb3 not found
283[ 43.114658] dwc3 fe800000.dwc3: IRQ host not found
284[ 43.116994] dwc3 fe800000.dwc3: IRQ dwc_usb3 not found
285[ 43.173539] dwc3 fe900000.dwc3: IRQ host not found
286[ 43.175525] dwc3 fe900000.dwc3: IRQ dwc_usb3 not found
287[ 43.229990] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
288[ 43.231925] ehci-pci: EHCI PCI platform driver
289[ 43.236028] ehci-platform: EHCI generic platform driver
290[ 43.249331] ehci-platform fe380000.usb: EHCI Host Controller
291[ 43.252152] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 1
292[ 43.258562] ehci-platform fe380000.usb: irq 31, io mem 0xfe380000
293[ 43.276573] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
294[ 43.287636] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
295[ 43.289460] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
296[ 43.291436] usb usb1: Product: EHCI Host Controller
297[ 43.292627] usb usb1: Manufacturer: Linux 5.3.0-rc6-next-20190830-g4fe25a02c4f1-sigmaris ehci_hcd
298[ 43.294299] usb usb1: SerialNumber: fe380000.usb
299[ 43.321645] hub 1-0:1.0: USB hub found
300[ 43.324859] hub 1-0:1.0: 1 port detected
301[ 43.355561] ehci-platform fe3c0000.usb: EHCI Host Controller
302[ 43.357663] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 2
303[ 43.364609] ehci-platform fe3c0000.usb: irq 33, io mem 0xfe3c0000
304[ 43.380507] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
305[ 43.390793] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
306[ 43.393252] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
307[ 43.394796] usb usb2: Product: EHCI Host Controller
308[ 43.396469] usb usb2: Manufacturer: Linux 5.3.0-rc6-next-20190830-g4fe25a02c4f1-sigmaris ehci_hcd
309[ 43.398162] usb usb2: SerialNumber: fe3c0000.usb
310[ 43.424370] hub 2-0:1.0: USB hub found
311[ 43.426760] hub 2-0:1.0: 1 port detected
312[ 43.458035] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
313[ 43.460424] ohci-pci: OHCI PCI platform driver
314[ 43.464177] ohci-platform: OHCI generic platform driver
315[ 43.474011] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
316[ 43.476788] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 3
317[ 43.482906] ohci-platform fe3a0000.usb: irq 32, io mem 0xfe3a0000
318[ 43.557545] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.03
319[ 43.560103] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
320[ 43.561621] usb usb3: Product: Generic Platform OHCI controller
321[ 43.563415] usb usb3: Manufacturer: Linux 5.3.0-rc6-next-20190830-g4fe25a02c4f1-sigmaris ohci_hcd
322[ 43.565099] usb usb3: SerialNumber: fe3a0000.usb
323[ 43.589622] hub 3-0:1.0: USB hub found
324[ 43.592485] hub 3-0:1.0: 1 port detected
325[ 43.617992] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
326[ 43.620744] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 4
327[ 43.626910] ohci-platform fe3e0000.usb: irq 34, io mem 0xfe3e0000
328[ 43.699723] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.03
329[ 43.701502] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
330[ 43.708069] usb usb4: Product: Generic Platform OHCI controller
331[ 43.709433] usb usb4: Manufacturer: Linux 5.3.0-rc6-next-20190830-g4fe25a02c4f1-sigmaris ohci_hcd
332[ 43.711633] usb usb4: SerialNumber: fe3e0000.usb
333[ 43.737845] hub 4-0:1.0: USB hub found
334[ 43.740644] hub 4-0:1.0: 1 port detected
335[ 43.798415] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
336[ 43.800992] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 5
337[ 43.809424] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
338[ 43.812438] xhci-hcd xhci-hcd.0.auto: irq 228, io mem 0xfe800000
339[ 43.831681] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
340[ 43.833423] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
341[ 43.835378] usb usb5: Product: xHCI Host Controller
342[ 43.836538] usb usb5: Manufacturer: Linux 5.3.0-rc6-next-20190830-g4fe25a02c4f1-sigmaris xhci-hcd
343[ 43.838194] usb usb5: SerialNumber: xhci-hcd.0.auto
344[ 43.862613] hub 5-0:1.0: USB hub found
345[ 43.865580] hub 5-0:1.0: 1 port detected
346[ 43.884772] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
347[ 43.886486] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 6
348[ 43.888935] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
349[ 43.893794] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
350[ 43.901461] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.03
351[ 43.903752] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
352[ 43.905218] usb usb6: Product: xHCI Host Controller
353[ 43.906375] usb usb6: Manufacturer: Linux 5.3.0-rc6-next-20190830-g4fe25a02c4f1-sigmaris xhci-hcd
354[ 43.908492] usb usb6: SerialNumber: xhci-hcd.0.auto
355[ 43.934697] hub 6-0:1.0: USB hub found
356[ 43.938114] hub 6-0:1.0: 1 port detected
357[ 43.964130] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
358[ 43.966060] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 7
359[ 43.973235] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
360[ 43.977233] xhci-hcd xhci-hcd.1.auto: irq 229, io mem 0xfe900000
361[ 43.995769] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
362[ 43.997518] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
363[ 43.999479] usb usb7: Product: xHCI Host Controller
364[ 44.000623] usb usb7: Manufacturer: Linux 5.3.0-rc6-next-20190830-g4fe25a02c4f1-sigmaris xhci-hcd
365[ 44.002289] usb usb7: SerialNumber: xhci-hcd.1.auto
366[ 44.025926] hub 7-0:1.0: USB hub found
367[ 44.028862] hub 7-0:1.0: 1 port detected
368[ 44.053028] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
369[ 44.054675] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 8
370[ 44.057428] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
371[ 44.061815] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
372[ 44.069458] usb usb8: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.03
373[ 44.071702] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
374[ 44.073148] usb usb8: Product: xHCI Host Controller
375[ 44.074269] usb usb8: Manufacturer: Linux 5.3.0-rc6-next-20190830-g4fe25a02c4f1-sigmaris xhci-hcd
376[ 44.076392] usb usb8: SerialNumber: xhci-hcd.1.auto
377[ 44.103801] hub 8-0:1.0: USB hub found
378[ 44.106224] hub 8-0:1.0: 1 port detected
379[ 44.133463] usbcore: registered new interface driver usb-storage
380[ 44.184378] i2c /dev entries driver
381[ 44.297156] rk808 0-001b: chip id: 0x0
382[ 44.390548] rk808-regulator rk808-regulator: there is no dvs0 gpio
383[ 44.393513] rk808-regulator rk808-regulator: there is no dvs1 gpio
384[ 44.398054] DCDC_REG1: supplied by vcc5v0_sys
385[ 44.420692] DCDC_REG2: supplied by vcc5v0_sys
386[ 44.438246] DCDC_REG3: supplied by vcc5v0_sys
387[ 44.452414] DCDC_REG4: supplied by vcc5v0_sys
388[ 44.471435] LDO_REG1: supplied by vcc5v0_sys
389[ 44.491647] LDO_REG2: supplied by vcc5v0_sys
390[ 44.510563] LDO_REG3: supplied by vcc5v0_sys
391[ 44.531513] LDO_REG4: supplied by vcc5v0_sys
392[ 44.536292] vcc_sdio: Bringing 3300000uV into 3000000-3000000uV
393[ 44.555698] LDO_REG5: supplied by vcc5v0_sys
394[ 44.573450] LDO_REG6: supplied by vcc5v0_sys
395[ 44.594118] LDO_REG7: supplied by vcc5v0_sys
396[ 44.612955] LDO_REG8: supplied by vcc5v0_sys
397[ 44.632429] SWITCH_REG1: supplied by vcc3v3_sys
398[ 44.648995] SWITCH_REG2: supplied by vcc3v3_sys
399[ 44.717246] rk808-rtc rk808-rtc: registered as rtc0
400[ 44.741242] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
401[ 44.744295] fan53555-reg: supplied by vcc5v0_sys
402[ 44.767519] vcc1v8_s3: supplied by vcc_1v8
403[ 44.791735] random: fast init done
404[ 44.792755] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
405[ 44.796126] fan53555-reg: supplied by vcc5v0_sys
406[ 45.000472] Bluetooth: HCI UART driver ver 2.3
407[ 45.070140] energy_model: pd0: hertz/watts ratio non-monotonically decreasing: em_cap_state 1 >= em_cap_state0
408[ 45.172534] cpufreq: cpufreq_online: CPU4: Running at unlisted freq: 12000 KHz
409[ 45.188605] cpufreq: cpufreq_online: CPU4: Unlisted initial frequency changed to: 408000 KHz
410[ 45.191462] sdhci: Secure Digital Host Controller Interface driver
411[ 45.192002] sdhci: Copyright(c) Pierre Ossman
412[ 45.192393] Synopsys Designware Multimedia Card Interface Driver
413[ 45.193237] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
414[ 45.193877] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
415[ 45.194475] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
416[ 45.195007] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 28,32 bit host data width,256 deep fifo
417[ 45.195913] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
418[ 45.196431] mmc_host mmc0: card is non-removable.
419[ 45.210083] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
420[ 45.224794] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
421[ 45.225525] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
422[ 45.226171] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
423[ 45.226996] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 29,32 bit host data width,256 deep fifo
424[ 45.228105] dwmmc_rockchip fe320000.dwmmc: Got CD GPIO
425[ 45.228838] vcc_sdio: unsupportable voltage range: 3300000-3000000uV
426[ 45.242051] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
427[ 45.255727] mmc_host mmc0: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
428[ 45.257763] sdhci-pltfm: SDHCI platform and OF driver helper
429[ 45.259179] mmc2: CQHCI version 5.10
430[ 45.285766] mmc2: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
431[ 45.289220] ledtrig-cpu: registered to indicate activity on CPUs
432[ 45.290379] usbcore: registered new interface driver usbhid
433[ 45.290887] usbhid: USB HID core driver
434[ 45.299261] xt_time: kernel timezone is -0000
435[ 45.299713] IPVS: Registered protocols (TCP, UDP, SCTP, AH, ESP)
436[ 45.300307] IPVS: Connection hash table configured (size=4096, memory=64Kbytes)
437[ 45.301185] IPVS: ipvs loaded.
438[ 45.301767] IPVS: [rr] scheduler registered.
439[ 45.302141] IPVS: [wrr] scheduler registered.
440[ 45.302522] IPVS: [lc] scheduler registered.
441[ 45.302905] IPVS: [wlc] scheduler registered.
442[ 45.302917] mmc_host mmc0: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
443[ 45.303287] IPVS: [fo] scheduler registered.
444[ 45.304458] IPVS: [ovf] scheduler registered.
445[ 45.304844] IPVS: [lblc] scheduler registered.
446[ 45.305236] IPVS: [lblcr] scheduler registered.
447[ 45.305632] IPVS: [dh] scheduler registered.
448[ 45.306006] IPVS: [sh] scheduler registered.
449[ 45.306379] IPVS: [sed] scheduler registered.
450[ 45.306768] IPVS: [nq] scheduler registered.
451[ 45.307208] IPv4 over IPsec tunneling driver
452[ 45.307952] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
453[ 45.308535] Initializing XFRM netlink socket
454[ 45.309166] NET: Registered protocol family 10
455[ 45.310365] Segment Routing with IPv6
456[ 45.311187] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
457[ 45.312379] NET: Registered protocol family 17
458[ 45.312791] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
459[ 45.313978] 8021q: 802.1Q VLAN Support v1.8
460[ 45.314404] 9pnet: Installing 9P2000 support
461[ 45.314805] Key type dns_resolver registered
462[ 45.315436] registered taskstats version 1
463[ 45.316229] Btrfs loaded, crc32c=crc32c-generic
464[ 45.333699] rockchip-drm display-subsystem: bound ff8f0000.vop (ops vop_component_ops)
465[ 45.335964] rockchip-drm display-subsystem: bound ff900000.vop (ops vop_component_ops)
466[ 45.336738] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
467[ 45.339330] rockchip-drm display-subsystem: bound ff940000.hdmi (ops dw_hdmi_rockchip_ops)
468[ 45.340056] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
469[ 45.340631] [drm] No driver support for vblank timestamp query.
470[ 45.354962] mmc_host mmc0: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
471[ 45.454160] Console: switching to colour frame buffer device 240x67
472[ 45.487338] rockchip-drm display-subsystem: fb0: rockchipdrmfb frame buffer device
473[ 45.488285] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0
474[ 45.490478] asoc-simple-card hdmi-sound: i2s-hifi <-> ff8a0000.i2s mapping ok
475[ 45.493032] input: gpio-keys as /devices/platform/gpio-keys/input/input0
476[ 45.495752] rk808-rtc rk808-rtc: setting system clock to 2019-09-01T16:17:55 UTC (1567354675)
477[ 45.496886] ALSA device list:
478[ 45.497148] #0: hdmi-sound
479[ 45.497544] ttyS2 - failed to request DMA
480[ 45.498232] Freeing unused kernel memory: 896K
481[ 45.510879] Run /init as init process
482[ 45.923837] rk_gmac-dwmac fe300000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet]
483[ 45.924702] rk_gmac-dwmac fe300000.ethernet eth0: phy: setting supported 00,00000000,000062ef advertising 00,00000000,000062ef
484[ 45.927577] rk_gmac-dwmac fe300000.ethernet eth0: No Safety Features support found
485[ 45.928258] rk_gmac-dwmac fe300000.ethernet eth0: PTP not supported by HW
486[ 45.928863] rk_gmac-dwmac fe300000.ethernet eth0: configuring for phy/rgmii link mode
487[ 45.929558] rk_gmac-dwmac fe300000.ethernet eth0: phylink_mac_config: mode=phy/rgmii/Unknown/Unknown adv=00,00000000,000062ef pause=10 link=0 an=1
488[ 45.930636] rk_gmac-dwmac fe300000.ethernet eth0: phy link down rgmii/Unknown/Unknown
489[ 49.819850] phy phy-ff770000.syscon:usb2-phy@e450.2: charger = USB_DCP_CHARGER
490[ 51.039441] rk_gmac-dwmac fe300000.ethernet eth0: phy link up rgmii/1Gbps/Full
491[ 51.039473] rk_gmac-dwmac fe300000.ethernet eth0: phylink_mac_config: mode=phy/rgmii/1Gbps/Full adv=00,00000000,00000000 pause=0e link=1 an=0
492[ 51.039505] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
493[ 51.040306] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
494[ 52.344265] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
495[ 52.347323] systemd[1]: Detected architecture arm64.
496[ 52.410079] systemd[1]: Set hostname to <netrp64>.
497[ 52.418854] systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument
498[ 53.307944] random: systemd: uninitialized urandom read (16 bytes read)
499[ 53.309784] systemd[1]: Listening on Network Service Netlink Socket.
500[ 53.322933] random: systemd: uninitialized urandom read (16 bytes read)
501[ 53.324689] systemd[1]: Listening on udev Kernel Socket.
502[ 53.326302] random: systemd: uninitialized urandom read (16 bytes read)
503[ 53.329287] systemd[1]: Listening on Journal Socket.
504[ 53.345393] systemd[1]: Starting Remount Root and Kernel File Systems...
505[ 53.347585] systemd[1]: Reached target Remote File Systems.
506[ 53.349940] systemd[1]: Listening on Journal Socket (/dev/log).
507[ 53.904568] systemd-journald[387]: Received request to flush runtime journal from PID 1
508[ 54.026664] random: crng init done
509[ 54.026981] random: 7 urandom warning(s) missed due to ratelimiting
510[ 54.848762] panfrost ff9a0000.gpu: clock rate = 500000000
511[ 54.849818] panfrost ff9a0000.gpu: mali-t860 id 0x860 major 0x2 minor 0x0 status 0x0
512[ 54.850511] panfrost ff9a0000.gpu: features: 00000000,100e77bf, issues: 00000000,24040400
513[ 54.851463] panfrost ff9a0000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7
514[ 54.851590] hantro_vpu: module is from the staging directory, the quality is unknown, you have been warned.
515[ 54.852500] panfrost ff9a0000.gpu: shader_present=0xf l2_present=0x1
516[ 54.858769] rockchip-rga ff680000.rga: HW Version: 0x03.02
517[ 54.860839] hantro-vpu ff650000.video-codec: Adding to iommu group 0
518[ 54.864832] rockchip-rga ff680000.rga: Registered rockchip-rga as /dev/video0
519[ 54.867428] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-enc as /dev/video1
520[ 54.868884] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-dec as /dev/video2
521[ 54.879423] [drm] Initialized panfrost 1.1.0 20180908 for ff9a0000.gpu on minor 1
522[ 58.351888] Bridge firewalling registered