· 6 years ago · Nov 04, 2019, 07:48 PM
1ecureInit read PBA: 0xc04
2SecureInit read PBA: 0x1004
3SecureInit read PBA: 0x1404
4SecureInit read PBA: 0x1804
5SecureInit read PBA: 0x1c04
6SecureInit ret = 0, SecureMode = 0
7atags_set_bootdev: ret:(0)
8GPT 0x3380ec0 signature is wrong
9recovery gpt...
10GPT 0x3380ec0 signature is wrong
11recovery gpt fail!
12LoadTrust Addr:0x4000
13No find bl30.bin
14No find bl32.bin
15Load uboot, ReadLba = 2000
16Load OK, addr=0x200000, size=0xdd07c
17RunBL31 0x10000
18NOTICE: BL31: v1.3(debug):22b599a
19NOTICE: BL31: Built : 11:03:32, Jul 10 2019
20NOTICE: BL31: Rockchip release version: v1.1
21INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
22INFO: Using opteed sec cpu_context!
23INFO: boot cpu mask: 0
24INFO: plat_rockchip_pmu_init(1181): pd status 3e
25INFO: BL31: Initializing runtime services
26WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s deK
27ERROR: Error initializing runtime service opteed_fast
28INFO: BL31: Preparing for EL3 exit to normal world
29INFO: Entry point address = 0x200000
30INFO: SPSR = 0x3c9
31fdtdec_get_addr_size_fixed: reg: addr=ff770000, size=10000
32fdtdec_get_addr_size_fixed: reg: addr=ff320000, size=1000
33
34
35U-Boot 2017.09-03638-g55e8e8b-dirty (Oct 04 2019 - 15:12:04 -0400)
36
37Model: Pine64 RK3399 Pinebook Pro
38PreSerial: 2
39DRAM: 3.9 GiB
40Sysmem: init
41Relocation Offset is: f5bf0000
42I2c0 speed: 400000Hz
43PMIC: RK808
44vdd_center 900000 uV
45vdd_log init 900000 uV
46rk_board_init PWM2 pinctrl init fail!
47rk_board_init: vcc3v0_sdio cannot set regulator value -38
48vdd_center 900000 uV
49 DCDC_REG1@ vdd_center: 750000uV <-> 1400000uV, set 900000uV, enabling | suspend
50 DCDC_REG4@ vcc_1v8: 1800000uV <-> 1800000uV, set 1800000uV, enabling | suspeng
51 LDO_REG1@ vcc1v8_dvp: 1800000uV <-> 1800000uV, set 1800000uV, enabling | suspeng
52 LDO_REG4@ vcc_sd: 3300000uV <-> 3300000uV, set 3300000uV, enabling | suspeng
53 LDO_REG7@ vcca1v8_codec: 1800000uV <-> 1800000uV, set 1800000uV, enabling | suspeng
54 LDO_REG8@ vcc_3v0: 3000000uV <-> 3000000uV, set 3000000uV, enabling | suspeng
55 SWITCH_REG2@ vcc3v3_s0: -61uV <-> -61uV, set 0uV, enabling | suspend
56 dc-12v@ dc_12v: 12000000uV <-> 12000000uV, set 12000000uV, enabling | sus)
57 vcc-sys@ vcc_sys: 5000000uV <-> 5000000uV, set 5000000uV, enabling | suspen)
58 vcc3v3-sys@ vcc3v3_sys: 3300000uV <-> 3300000uV, set 3300000uV, enabling | suspen)
59 vcc-phy-regulator@ vcc_phy: -61uV <-> -61uV, set -61uV, enabling | suspeng
60 led-regulator@ led_regulator: -61uV <-> -61uV, set -61uV, enabling | suspeng
61 vcc5v0-host-en@ vcc5v0_host: 5000000uV <-> 5000000uV, set 5000000uV, enabling | suspen)
62vcc5v0-usb3-host-regulator@vcc5v0_usb3_host: -61uV <-> -61uV, set -61uV, enabling | suspg
63 vcc5v0-typec0-en@ vcc5v0_typec0: -61uV <-> -61uV, set -61uV, enabling | suspeng
64 vcc1v8-sdio@ vcc1v8_sdio: 1800000uV <-> 1800000uV, set 1800000uV, enabling | suspen)
65 vcc3v0-sdio@ vcc3v0_sdio: 3000000uV <-> 3000000uV, set 3000000uV, enabling | suspen)
66vdd_log init 900000 uV
67 vdd_log@ vdd_log: 800000uV <-> 1400000uV, set 900000uV, enabling | suspenV
68MMC: dwmmc@fe310000: 2, sdhci@fe330000: 0, dwmmc@fe320000: 1
69Invalid bus 0 (err=-19)
70*** Warning - spi_flash_probe_bus_cs() failed, using default environment
71
72In: serial
73Out: serial
74Err: serial
75Model: Pine64 RK3399 Pinebook Pro
76RKPARM: Invalid parameter part table
77switch to partitions #0, OK
78mmc1 is current device
79Found IDB in SDcard
80Bootdev(atags): mmc 1
81PartType: DOS
82rockchip_get_boot_mode: Could not found misc partition
83boot mode: None
84init_resource_list: failed to get resource part, ret=-1
85Can't find file:logo.bmp
86failed to display uboot logo
87CLK: (uboot. arml: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
88CLK: (uboot. armb: enter 24000 KHz, init 24000 KHz, kernel 0N/A)
89 aplll 816000 KHz
90 apllb 24000 KHz
91 dpll 800000 KHz
92 cpll 24000 KHz
93 gpll 800000 KHz
94 npll 600000 KHz
95 vpll 24000 KHz
96 aclk_perihp 133333 KHz
97 hclk_perihp 66666 KHz
98 pclk_perihp 33333 KHz
99 aclk_perilp0 266666 KHz
100 hclk_perilp0 88888 KHz
101 pclk_perilp0 44444 KHz
102 hclk_perilp1 100000 KHz
103 pclk_perilp1 50000 KHz
104Net: No ethernet found.
105Hit key to stop autoboot('CTRL+C'): 0
106do_boot_rockchip: Could not find boot part
107Checking for mmc dev 1...
108RKPARM: Invalid parameter part table
109switch to partitions #0, OK
110mmc1 is current device
111Scanning mmc 1 for bootable partitions...
112Scanning mmc 1:1 for extlinux or boot scripts...
113Found U-Boot script /boot/boot.scr
1141024 bytes read in 13 ms (76.2 KiB/s)
115## Executing script at 00500000
11628379144 bytes read in 1220 ms (22.2 MiB/s)
11798517 bytes read in 92 ms (1 MiB/s)
118** File not found /boot/initramfs-linux.img **
119## Flattened Device Tree blob at 08300000
120 Booting using the fdt blob at 0x8300000
121 reserving fdt memory region: addr=8300000 size=19000
122fdtdec_get_addr_size_fixed: reg: addr=00000000, size=0
123 Loading Device Tree to 00000000f3dbc000, end 00000000f3dd7fff ... OK
124Adding bank: 0x00200000 - 0xf8000000 (size: 0xf7e00000)
125Total: 2450.873 ms
126
127Starting kernel ...
128
129[ 0.000000] Booting Linux on physical CPU 0x0
130[ 0.000000] Initializing cgroup subsys cpuset
131[ 0.000000] Initializing cgroup subsys cpu
132[ 0.000000] Initializing cgroup subsys cpuacct
133[ 0.000000] Linux version 4.4.196-1-Manjaro-ARM (ray@ray-pc) (gcc version 9.2.0 (GCC) ) #1 SMP Su9
134[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
135[ 0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
136[ 0.000000] bootconsole [uart0] enabled
137[ 0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x000000B
138[ 0.000000] psci: probing for conduit method from DT.
139[ 0.000000] psci: PSCIv1.0 detected in firmware.
140[ 0.000000] psci: Using standard PSCI v0.2 function IDs
141[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
142[ 0.000000] PERCPU: Embedded 20 pages/cpu @ffffffc0f7ed9000 s41960 r8192 d31768 u81920
143[ 0.000000] Detected VIPT I-cache on CPU0
144[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
145[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 999432
146[ 0.000000] Kernel command line: console=ttyS2,1500000 root=PARTUUID=d5af3c2d-01 rw rootwait boot0
147[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
148[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
149[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
150[ 0.000000] software IO TLB: mapped [mem 0xf7e91000-0xf7ed1000] (0MB)
151[ 0.000000] Memory: 3959320K/4061184K available (15486K kernel code, 2178K rwdata, 8812K rodata, )
152[ 0.000000] Virtual kernel memory layout:
153[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
154[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 GB)
155[ 0.000000] .init : 0xffffff8009840000 - 0xffffff8009970000 ( 1216 KB)
156[ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008fa0000 ( 15488 KB)
157[ 0.000000] .rodata : 0xffffff8008fa0000 - 0xffffff8009840000 ( 8832 KB)
158[ 0.000000] .data : 0xffffff8009970000 - 0xffffff8009b90808 ( 2179 KB)
159[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
160[ 0.000000] 0xffffffbdc0008000 - 0xffffffbdc3e00000 ( 61 MB actual)
161[ 0.000000] fixed : 0xffffffbffe7fb000 - 0xffffffbffec00000 ( 4116 KB)
162[ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB)
163[ 0.000000] memory : 0xffffffc000200000 - 0xffffffc0f8000000 ( 3966 MB)
164[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
165[ 0.000000] Hierarchical RCU implementation.
166[ 0.000000] Build-time adjustment of leaf fanout to 64.
167[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
168[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
169[ 0.000000] NR_IRQS:64 nr_irqs:64 0
170[ 0.000000] GIC: Using split EOI/Deactivate mode
171[ 0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
172[ 0.000000] ITS: allocated 65536 Devices @f3080000 (psz 64K, shr 0)
173[ 0.000000] ITS: using cache flushing for cmd queue
174[ 0.000000] GIC: using LPI property table @0x00000000f3010000
175[ 0.000000] ITS: Allocated 1792 chunks for LPIs
176[ 0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
177[ 0.000000] CPU0: using LPI pending table @0x00000000f3020000
178[ 0.000000] GIC: using cache flushing for LPI property table
179[ 0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu}
180[ 0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
181[ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vok
182[ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vok
183[ 0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
184[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
185[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_ids
186[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
187[ 0.002218] Console: colour dummy device 80x25
188[ 0.002660] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 Bogo)
189[ 0.003651] pid_max: default: 32768 minimum: 301
190[ 0.004229] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
191[ 0.004882] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
192[ 0.006304] Initializing cgroup subsys memory
193[ 0.006745] Initializing cgroup subsys devices
194[ 0.007189] Initializing cgroup subsys freezer
195[ 0.007625] Initializing cgroup subsys net_cls
196[ 0.008055] Initializing cgroup subsys net_prio
197[ 0.008519] ftrace: allocating 55018 entries in 215 pages
198[ 0.151083] sched-energy: Sched-energy-costs installed from DT
199[ 0.151652] CPU0: update cpu_capacity 401
200[ 0.152097] ASID allocator initialised with 32768 entries
201[ 0.156460] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
202[ 0.157871] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain cred
203[ 0.160128] Detected VIPT I-cache on CPU1
204[ 0.160162] CPU1: found redistributor 1 region 0:0x00000000fef20000
205[ 0.160193] CPU1: using LPI pending table @0x00000000f32e0000
206[ 0.160237] CPU1: update cpu_capacity 401
207[ 0.160241] CPU1: Booted secondary processor [410fd034]
208[ 0.160774] Detected VIPT I-cache on CPU2
209[ 0.160795] CPU2: found redistributor 2 region 0:0x00000000fef40000
210[ 0.160822] CPU2: using LPI pending table @0x00000000f3310000
211[ 0.160850] CPU2: update cpu_capacity 401
212[ 0.160853] CPU2: Booted secondary processor [410fd034]
213[ 0.161370] Detected VIPT I-cache on CPU3
214[ 0.161390] CPU3: found redistributor 3 region 0:0x00000000fef60000
215[ 0.161417] CPU3: using LPI pending table @0x00000000f3360000
216[ 0.161443] CPU3: update cpu_capacity 401
217[ 0.161447] CPU3: Booted secondary processor [410fd034]
218[ 0.161988] Detected PIPT I-cache on CPU4
219[ 0.162016] CPU4: found redistributor 100 region 0:0x00000000fef80000
220[ 0.162055] CPU4: using LPI pending table @0x00000000f3390000
221[ 0.162093] CPU4: update cpu_capacity 1024
222[ 0.162096] CPU4: Booted secondary processor [410fd082]
223[ 0.162638] Detected PIPT I-cache on CPU5
224[ 0.162658] CPU5: found redistributor 101 region 0:0x00000000fefa0000
225[ 0.162695] CPU5: using LPI pending table @0x00000000f33c0000
226[ 0.162721] CPU5: update cpu_capacity 1024
227[ 0.162725] CPU5: Booted secondary processor [410fd082]
228[ 0.162825] Brought up 6 CPUs
229[ 0.175191] SMP: Total of 6 processors activated.
230[ 0.175643] CPU features: detected feature: GIC system register CPU interface
231[ 0.176330] CPU features: detected feature: 32-bit EL0 Support
232[ 0.176891] CPU: All CPU(s) started at EL2
233[ 0.177323] alternatives: patching kernel code
234[ 0.179146] devtmpfs: initialized
235[ 0.196722] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 191126044s
236[ 0.197657] futex hash table entries: 2048 (order: 5, 131072 bytes)
237[ 0.198721] xor: measuring software checksum speed
238[ 0.209082] 8regs : 2856.000 MB/sec
239[ 0.219137] 8regs_prefetch: 2560.000 MB/sec
240[ 0.229192] 32regs : 3212.000 MB/sec
241[ 0.239249] 32regs_prefetch: 2844.000 MB/sec
242[ 0.239681] xor: using function: 32regs (3212.000 MB/sec)
243[ 0.240208] pinctrl core: initialized pinctrl subsystem
244[ 0.242716] NET: Registered protocol family 16
245[ 0.247395] cpuidle: using governor ladder
246[ 0.251409] cpuidle: using governor menu
247[ 0.252093] vdso: 2 pages (1 code @ ffffff8008fa6000, 1 data @ ffffff8009974000)
248[ 0.252813] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
249[ 0.254486] DMA: preallocated 2048 KiB pool for atomic allocations
250[ 0.329862] raid6: int64x1 gen() 453 MB/s
251[ 0.346950] raid6: int64x1 xor() 357 MB/s
252[ 0.363974] raid6: int64x2 gen() 800 MB/s
253[ 0.381078] raid6: int64x2 xor() 595 MB/s
254[ 0.398154] raid6: int64x4 gen() 1128 MB/s
255[ 0.415291] raid6: int64x4 xor() 673 MB/s
256[ 0.432392] raid6: int64x8 gen() 828 MB/s
257[ 0.449487] raid6: int64x8 xor() 607 MB/s
258[ 0.466576] raid6: neonx1 gen() 925 MB/s
259[ 0.483670] raid6: neonx1 xor() 636 MB/s
260[ 0.500739] raid6: neonx2 gen() 1593 MB/s
261[ 0.517831] raid6: neonx2 xor() 1000 MB/s
262[ 0.534928] raid6: neonx4 gen() 2078 MB/s
263[ 0.552034] raid6: neonx4 xor() 1216 MB/s
264[ 0.569119] raid6: neonx8 gen() 1699 MB/s
265[ 0.586202] raid6: neonx8 xor() 1242 MB/s
266[ 0.586606] raid6: using algorithm neonx4 gen() 2078 MB/s
267[ 0.587112] raid6: .... xor() 1216 MB/s, rmw enabled
268[ 0.587575] raid6: using intx1 recovery algorithm
269[ 0.588544] ACPI: Interpreter disabled.
270[ 0.590074] vcc3v3_sys: supplied by vcc_sys
271[ 0.591342] vcc_lcd_en: supplied by vcc3v3_sys
272[ 0.592201] vcc1v8_sdio: regulator get failed, ret=-517
273[ 0.592916] vcc3v0_sdio: supplied by vcc3v3_sys
274[ 0.594217] iommu: Adding device ff650000.vpu_service to group 0
275[ 0.594866] iommu: Adding device ff660000.rkvdec to group 1
276[ 0.595488] iommu: Adding device ff8f0000.vop to group 2
277[ 0.596072] iommu: Adding device ff900000.vop to group 3
278[ 0.598037] SCSI subsystem initialized
279[ 0.598721] usbcore: registered new interface driver usbfs
280[ 0.599284] usbcore: registered new interface driver hub
281[ 0.599859] usbcore: registered new device driver usb
282[ 0.600466] media: Linux media interface: v0.10
283[ 0.600916] Linux video capture interface: v2.00
284[ 0.601452] pps_core: LinuxPPS API ver. 1 registered
285[ 0.601916] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.>
286[ 0.602790] PTP clock support registered
287[ 0.604439] Advanced Linux Sound Architecture Driver Initialized.
288[ 0.605522] Bluetooth: Core ver 2.21
289[ 0.605883] NET: Registered protocol family 31
290[ 0.606309] Bluetooth: HCI device and connection manager initialized
291[ 0.606907] Bluetooth: HCI socket layer initialized
292[ 0.607375] Bluetooth: L2CAP socket layer initialized
293[ 0.607878] Bluetooth: SCO socket layer initialized
294[ 0.609540] clocksource: Switched to clocksource arch_sys_counter
295[ 0.650706] FS-Cache: Loaded
296[ 0.651180] pnp: PnP ACPI: disabled
297[ 0.660128] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
298[ 0.661138] NET: Registered protocol family 2
299[ 0.662006] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
300[ 0.662948] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
301[ 0.664391] TCP: Hash tables configured (established 32768 bind 32768)
302[ 0.665142] UDP hash table entries: 2048 (order: 5, 196608 bytes)
303[ 0.665897] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
304[ 0.666929] NET: Registered protocol family 1
305[ 0.667654] RPC: Registered named UNIX socket transport module.
306[ 0.668211] RPC: Registered udp transport module.
307[ 0.668670] RPC: Registered tcp transport module.
308[ 0.669110] RPC: Registered tcp NFSv4.1 backchannel transport module.
309[ 0.671047] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
310[ 0.671907] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
311[ 0.675820] Initialise system trusted keyring
312[ 0.682331] zbud: loaded
313[ 0.684658] squashfs: version 4.0 (2009/01/31) Phillip Lougher
314[ 0.685983] NFS: Registering the id_resolver key type
315[ 0.686472] Key type id_resolver registered
316[ 0.686879] Key type id_legacy registered
317[ 0.687265] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
318[ 0.688564] fuse init (API version 7.23)
319[ 0.689290] SGI XFS with security attributes, no debug enabled
320[ 0.691426] aufs 4.4-20170911
321[ 0.695981] NET: Registered protocol family 38
322[ 0.696416] async_tx: api initialized (async)
323[ 0.696851] Key type asymmetric registered
324[ 0.697243] Asymmetric key parser 'x509' registered
325[ 0.697891] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
326[ 0.698599] io scheduler noop registered
327[ 0.698974] io scheduler deadline registered
328[ 0.699513] io scheduler cfq registered (default)
329[ 0.701289] phy phy-ff770000.syscon:usb2-phy@e460.0: Failed to get VBUS supply regulator
330[ 0.707987] universal-charger usb-charger: invalid dc det gpio!
331[ 0.708568] universal-charger usb-charger: init usb failed!
332[ 0.710945] rk-vcodec ff650000.vpu_service: no regulator for vcodec
333[ 0.711776] rk-vcodec ff650000.vpu_service: probe device
334[ 0.712486] rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled
335[ 0.713721] rk-vcodec ff650000.vpu_service: init success
336[ 0.714455] rk-vcodec ff660000.rkvdec: no regulator for vcodec
337[ 0.715442] rk-vcodec ff660000.rkvdec: probe device
338[ 0.716107] rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled
339[ 0.717112] rk-vcodec ff660000.rkvdec: could not find power_model node
340[ 0.717739] rk-vcodec ff660000.rkvdec: init success
341[ 0.719974] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
342[ 0.720696] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_2
343[ 0.722993] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
344[ 0.723719] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num6
345[ 0.725183] pwm-regulator: supplied by vcc_sys
346[ 0.726328] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
347[ 0.728648] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 35, base_baud = 1500000) is a 16550A
348[ 0.730112] console [ttyS2] disabled
349[ 0.730480] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 36, base_baud = 1500000) is a 16550A
350[ 0.731346] console [ttyS2] enabled
351[ 0.731346] console [ttyS2] enabled
352[ 0.732000] bootconsole [uart0] disabled
353[ 0.732000] bootconsole [uart0] disabled
354[ 0.733793] [drm] Initialized drm 1.1.0 20060810
355[ 0.738154] [drm] Rockchip DRM driver version: v1.0.1
356[ 0.739156] usbcore: registered new interface driver udl
357[ 0.741434] Unable to detect cache hierarchy for CPU 0
358[ 0.742670] brd: module loaded
359[ 0.748167] loop: module loaded
360[ 0.749016] zram: Added device: zram0
361[ 0.749705] lkdtm: No crash points registered, enable through debugfs
362[ 0.751413] rockchip-spi ff1d0000.spi: no high_speed pinctrl state
363[ 0.752870] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
364[ 0.753406] e100: Copyright(c) 1999-2006 Intel Corporation
365[ 0.753949] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
366[ 0.754577] e1000: Copyright (c) 1999-2006 Intel Corporation.
367[ 0.755124] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
368[ 0.755645] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
369[ 0.756212] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k
370[ 0.756832] igb: Copyright (c) 2007-2014 Intel Corporation.
371[ 0.757365] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.2.1-k
372[ 0.758044] ixgbe: Copyright (c) 1999-2015 Intel Corporation.
373[ 0.759347] Atmel at76x USB Wireless LAN Driver 0.17 loading
374[ 0.759910] usbcore: registered new interface driver at76c50x-usb
375[ 0.760495] Broadcom 43xx driver loaded [ Features: PNL ]
376[ 0.761138] usbcore: registered new interface driver zd1211rw
377[ 0.761703] usbcore: registered new interface driver rtl8187
378[ 0.762300] usbcore: registered new interface driver rtl8192cu
379[ 0.763137] usbcore: registered new interface driver rtl8xxxu
380[ 0.763699] usbcore: registered new interface driver rndis_wlan
381[ 0.764265] usbcore: registered new interface driver usb8xxx
382[ 0.764948] usbcore: registered new interface driver rt2500usb
383[ 0.765519] usbcore: registered new interface driver rt73usb
384[ 0.766057] usbcore: registered new interface driver rt2800usb
385[ 0.766616] usbcore: registered new interface driver mt7601u
386[ 0.767245] usbcore: registered new interface driver ath6kl_usb
387[ 0.767812] usbcore: registered new interface driver ar5523
388[ 0.768526] usbcore: registered new interface driver mwifiex_usb
389[ 0.769122] usbcore: registered new interface driver brcmfmac
390[ 0.769691] Rockchip WiFi SYS interface (V1.00) ...
391[ 0.770205] usbcore: registered new interface driver rtl8150
392[ 0.770757] usbcore: registered new interface driver r8152
393[ 0.771287] usbcore: registered new interface driver asix
394[ 0.771811] usbcore: registered new interface driver ax88179_178a
395[ 0.772381] usbcore: registered new interface driver cdc_ether
396[ 0.772945] usbcore: registered new interface driver rndis_host
397[ 0.773540] usbcore: registered new interface driver cdc_ncm
398[ 0.774074] usbcore: registered new interface driver cdc_mbim
399[ 0.776053] rockchip-dwc3 usb0: failed to get drvdata dwc3
400[ 0.780916] rockchip-dwc3 usb1: fail to get drvdata hcd
401[ 0.782629] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
402[ 0.783219] ehci-pci: EHCI PCI platform driver
403[ 0.783686] ehci-platform: EHCI generic platform driver
404[ 0.788038] ehci-platform fe3c0000.usb: EHCI Host Controller
405[ 0.788712] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
406[ 0.789521] ehci-platform fe3c0000.usb: irq 29, io mem 0xfe3c0000
407[ 0.795532] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
408[ 0.796225] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
409[ 0.796838] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
410[ 0.797473] usb usb1: Product: EHCI Host Controller
411[ 0.797914] usb usb1: Manufacturer: Linux 4.4.196-1-Manjaro-ARM ehci_hcd
412[ 0.798512] usb usb1: SerialNumber: fe3c0000.usb
413[ 0.799369] hub 1-0:1.0: USB hub found
414[ 0.799739] hub 1-0:1.0: 1 port detected
415[ 0.800679] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
416[ 0.801236] ohci-platform: OHCI generic platform driver
417[ 0.802218] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
418[ 0.802970] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
419[ 0.803766] ohci-platform fe3e0000.usb: irq 30, io mem 0xfe3e0000
420[ 0.858676] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
421[ 0.859275] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
422[ 0.859920] usb usb2: Product: Generic Platform OHCI controller
423[ 0.860442] usb usb2: Manufacturer: Linux 4.4.196-1-Manjaro-ARM ohci_hcd
424[ 0.861039] usb usb2: SerialNumber: fe3e0000.usb
425[ 0.861887] hub 2-0:1.0: USB hub found
426[ 0.862243] hub 2-0:1.0: 1 port detected
427[ 0.863536] usbcore: registered new interface driver cdc_wdm
428[ 0.864081] usbcore: registered new interface driver uas
429[ 0.864635] usbcore: registered new interface driver usb-storage
430[ 0.865199] usbcore: registered new interface driver ums-alauda
431[ 0.865766] usbcore: registered new interface driver ums-cypress
432[ 0.866329] usbcore: registered new interface driver ums-datafab
433[ 0.866902] usbcore: registered new interface driver ums_eneub6250
434[ 0.867479] usbcore: registered new interface driver ums-freecom
435[ 0.868055] usbcore: registered new interface driver ums-isd200
436[ 0.868621] usbcore: registered new interface driver ums-jumpshot
437[ 0.869190] usbcore: registered new interface driver ums-karma
438[ 0.869753] usbcore: registered new interface driver ums-onetouch
439[ 0.870331] usbcore: registered new interface driver ums-realtek
440[ 0.870907] usbcore: registered new interface driver ums-sddr09
441[ 0.871461] usbcore: registered new interface driver ums-sddr55
442[ 0.872026] usbcore: registered new interface driver ums-usbat
443[ 0.872632] usbcore: registered new interface driver usbserial
444[ 0.873176] usbcore: registered new interface driver usbserial_generic
445[ 0.873785] usbserial: USB Serial support registered for generic
446[ 0.874352] usbcore: registered new interface driver cp210x
447[ 0.874871] usbserial: USB Serial support registered for cp210x
448[ 0.875443] usbcore: registered new interface driver ftdi_sio
449[ 0.875981] usbserial: USB Serial support registered for FTDI USB Serial Device
450[ 0.876718] usbcore: registered new interface driver keyspan
451[ 0.877239] usbserial: USB Serial support registered for Keyspan - (without firmware)
452[ 0.877955] usbserial: USB Serial support registered for Keyspan 1 port adapter
453[ 0.878626] usbserial: USB Serial support registered for Keyspan 2 port adapter
454[ 0.879287] usbserial: USB Serial support registered for Keyspan 4 port adapter
455[ 0.879977] usbcore: registered new interface driver option
456[ 0.880488] usbserial: USB Serial support registered for GSM modem (1-port)
457[ 0.881215] usbcore: registered new interface driver oti6858
458[ 0.881744] usbserial: USB Serial support registered for oti6858
459[ 0.882313] usbcore: registered new interface driver pl2303
460[ 0.882835] usbserial: USB Serial support registered for pl2303
461[ 0.883399] usbcore: registered new interface driver qcserial
462[ 0.883933] usbserial: USB Serial support registered for Qualcomm USB modem
463[ 0.884600] usbcore: registered new interface driver sierra
464[ 0.885113] usbserial: USB Serial support registered for Sierra USB modem
465[ 0.886996] usbcore: registered new interface driver iforce
466[ 0.888095] usbcore: registered new interface driver xpad
467[ 0.889013] usbcore: registered new interface driver usbtouchscreen
468[ 0.889864] sensor_register_slave:mma8452,id=17
469[ 0.890272] sensor_register_slave:lis3dh,id=7
470[ 0.890676] sensor_register_slave:mma7660,id=18
471[ 0.891082] sensor_register_slave:lsm303d,id=22
472[ 0.891488] sensor_register_slave:mpu6880_acc,id=24
473[ 0.891934] sensor_register_slave:mpu6500_acc,id=25
474[ 0.892372] sensor_register_slave:lsm330_acc,id=26
475[ 0.892809] sensor_register_slave:akm8975,id=30
476[ 0.893216] sensor_register_slave:akm8963,id=31
477[ 0.893631] sensor_register_slave:l3g4200d,id=45
478[ 0.894045] sensor_register_slave:l3g20d,id=46
479[ 0.894444] sensor_register_slave:ewtsa,id=47
480[ 0.894844] sensor_register_slave:lsm330_gyro,id=51
481[ 0.895282] sensor_register_slave:cm3217,id=53
482[ 0.895686] sensor_register_slave:cm3218,id=54
483[ 0.896761] i2c /dev entries driver
484[ 0.898411] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
485[ 0.899091] fan53555-reg: supplied by vcc_sys
486[ 0.901901] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
487[ 0.902566] fan53555-reg: supplied by vcc_sys
488[ 0.905402] rk808 0-001b: Pmic Chip id: 0x0
489[ 0.908862] rk808-regulator rk808-regulator: there is no dvs0 gpio
490[ 0.909451] rk808-regulator rk808-regulator: there is no dvs1 gpio
491[ 0.910100] DCDC_REG1: supplied by vcc_sys
492[ 0.911236] DCDC_REG2: supplied by vcc_sys
493[ 0.912217] DCDC_REG3: supplied by vcc_sys
494[ 0.912897] DCDC_REG4: supplied by vcc_sys
495[ 0.913676] vcc1v8_sdio: supplied by vcc_1v8
496[ 0.914156] LDO_REG1: supplied by vcc_sys
497[ 0.915647] LDO_REG2: supplied by vcc_sys
498[ 0.916454] LDO_REG3: supplied by vcc_sys
499[ 0.917803] LDO_REG4: supplied by vcc_sys
500[ 0.918334] vcc_sd: Bringing 3300000uV into 3000000-3000000uV
501[ 0.919796] LDO_REG5: supplied by vcc_sys
502[ 0.920330] vcca3v0_codec: Bringing 1800000uV into 3000000-3000000uV
503[ 0.921943] LDO_REG6: supplied by vcc_sys
504[ 0.923273] LDO_REG7: supplied by vcc_sys
505[ 0.924646] LDO_REG8: supplied by vcc_sys
506[ 0.925995] SWITCH_REG1: supplied by vcc3v3_sys
507[ 0.926720] SWITCH_REG2: supplied by vcc_lcd_en
508[ 1.031545] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
509[ 1.032642] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff8009cd8000
510[ 1.034311] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff8009cda000
511[ 1.045290] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
512[ 1.078218] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
513[ 1.079250] cw201x 4-0062: cw2015/cw2013 driver v1.2 probe sucess
514[ 1.079845] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff8009cdc000
515[ 1.082056] lirc_dev: IR Remote Control driver registered, major 242
516[ 1.082646] IR NEC protocol handler initialized
517[ 1.083055] IR RC5(x/sz) protocol handler initialized
518[ 1.083518] IR RC6 protocol handler initialized
519[ 1.083925] IR JVC protocol handler initialized
520[ 1.084331] IR Sony protocol handler initialized
521[ 1.084757] IR SANYO protocol handler initialized
522[ 1.085180] IR Sharp protocol handler initialized
523[ 1.085615] IR MCE Keyboard/mouse protocol handler initialized
524[ 1.086135] IR LIRC bridge handler initialized
525[ 1.086546] IR XMP protocol handler initialized
526[ 1.088423] usbcore: registered new interface driver uvcvideo
527[ 1.088961] USB Video Class driver (1.1.1)
528[ 1.090849] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647
529[ 1.091929] rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
530[ 1.093764] md: raid0 personality registered for level 0
531[ 1.094242] md: raid1 personality registered for level 1
532[ 1.094741] md: raid10 personality registered for level 10
533[ 1.095538] md: raid6 personality registered for level 6
534[ 1.096008] md: raid5 personality registered for level 5
535[ 1.096477] md: raid4 personality registered for level 4
536[ 1.097415] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
537[ 1.098183] device-mapper: raid: Loading target version 1.7.0
538[ 1.098710] Bluetooth: Virtual HCI driver ver 1.5
539[ 1.099327] Bluetooth: HCI UART driver ver 2.3
540[ 1.099740] Bluetooth: HCI UART protocol H4 registered
541[ 1.100194] Bluetooth: HCI UART protocol ATH3K registered
542[ 1.100786] usbcore: registered new interface driver bfusb
543[ 1.101345] usbcore: registered new interface driver btusb
544[ 1.101851] rtk_btusb: RTKBT_RELEASE_NAME: 20180702_BT_ANDROID_8.1
545[ 1.102394] rtk_btusb: Realtek Bluetooth USB driver module init, version 4.1.5
546[ 1.103042] rtk_btusb: Register usb char device interface for BT driver
547[ 1.103914] usbcore: registered new interface driver rtk_btusb
548[ 1.105391] cpu cpu0: leakage=11
549[ 1.107611] cpu cpu4: leakage=20
550[ 1.112701] cpu cpu0: failed to find power_model node
551[ 1.116602] cpu cpu4: failed to find power_model node
552[ 1.117887] sdhci: Secure Digital Host Controller Interface driver
553[ 1.118426] sdhci: Copyright(c) Pierre Ossman
554[ 1.118817] Synopsys Designware Multimedia Card Interface Driver
555[ 1.119756] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
556[ 1.120404] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
557[ 1.121016] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
558[ 1.121551] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 24,32 bit host data width,256o
559[ 1.122979] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
560[ 1.123636] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
561[ 1.124234] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
562[ 1.124759] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256o
563[ 1.136537] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div )
564[ 1.147733] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
565[ 1.148735] sdhci-pltfm: SDHCI platform and OF driver helper
566[ 1.150961] sdhci-arasan fe330000.sdhci: No vmmc regulator found
567[ 1.151487] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
568[ 1.178685] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
569[ 1.180690] ledtrig-cpu: registered to indicate activity on CPUs
570[ 1.181331] hidraw: raw HID events driver (C) Jiri Kosina
571[ 1.183923] usbcore: registered new interface driver usbhid
572[ 1.184412] usbhid: USB HID core driver
573[ 1.185838] usbcore: registered new interface driver snd-usb-audio
574[ 1.189525] u32 classifier
575[ 1.189772] Netfilter messages via NETLINK v0.30.
576[ 1.190218] ip_set: protocol 6
577[ 1.190586] ip_tables: (C) 2000-2006 Netfilter Core Team
578[ 1.191077] Initializing XFRM netlink socket
579[ 1.191740] NET: Registered protocol family 10
580[ 1.192647] NET: Registered protocol family 17
581[ 1.193046] NET: Registered protocol family 15
582[ 1.193449] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scr.
583[ 1.194566] Bridge firewalling registered
584[ 1.195350] Bluetooth: RFCOMM socket layer initialized
585[ 1.195838] Bluetooth: RFCOMM ver 1.11
586[ 1.221393] rockchip-drm display-subsystem: defer getting devfreq
587[ 1.222479] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff800907b7e0)
588[ 1.223381] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff800907b7e0)
589[ 1.223661] mmc1: MAN_BKOPS_EN bit is not set
590[ 1.223725] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 1000000)
591[ 1.225514] rockchip-drm display-subsystem: failed to bind ff970000.edp (ops 0xffffff8009073be8):7
592[ 1.226622] rockchip-drm display-subsystem: master bind failed: -517
593[ 1.232447] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
594[ 1.233211] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3
595[ 1.234020] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x00010010
596[ 1.234834] xhci-hcd xhci-hcd.2.auto: irq 225, io mem 0xfe800000
597[ 1.235459] mmc1: new HS200 MMC card at address 0001
598[ 1.235490] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
599[ 1.235494] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
600[ 1.235497] usb usb3: Product: xHCI Host Controller
601[ 1.235509] usb usb3: Manufacturer: Linux 4.4.196-1-Manjaro-ARM xhci-hcd
602[ 1.235513] usb usb3: SerialNumber: xhci-hcd.2.auto
603[ 1.235926] hub 3-0:1.0: USB hub found
604[ 1.235949] hub 3-0:1.0: 1 port detected
605[ 1.236182] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
606[ 1.236293] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4
607[ 1.236338] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
608[ 1.236407] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
609[ 1.236411] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
610[ 1.236414] usb usb4: Product: xHCI Host Controller
611[ 1.236417] usb usb4: Manufacturer: Linux 4.4.196-1-Manjaro-ARM xhci-hcd
612[ 1.236420] usb usb4: SerialNumber: xhci-hcd.2.auto
613[ 1.236776] hub 4-0:1.0: USB hub found
614[ 1.236795] hub 4-0:1.0: 1 port detected
615[ 1.238054] xhci-hcd xhci-hcd.2.auto: remove, state 1
616[ 1.238071] usb usb4: USB disconnect, device number 1
617[ 1.238396] xhci-hcd xhci-hcd.2.auto: USB bus 4 deregistered
618[ 1.238468] xhci-hcd xhci-hcd.2.auto: remove, state 1
619[ 1.238476] usb usb3: USB disconnect, device number 1
620[ 1.242629] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
621[ 1.242768] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 4
622[ 1.242891] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x00010010
623[ 1.242920] xhci-hcd xhci-hcd.3.auto: irq 226, io mem 0xfe900000
624[ 1.242989] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
625[ 1.242992] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
626[ 1.242994] usb usb4: Product: xHCI Host Controller
627[ 1.242996] usb usb4: Manufacturer: Linux 4.4.196-1-Manjaro-ARM xhci-hcd
628[ 1.242998] usb usb4: SerialNumber: xhci-hcd.3.auto
629[ 1.243359] hub 4-0:1.0: USB hub found
630[ 1.243370] hub 4-0:1.0: 1 port detected
631[ 1.243496] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
632[ 1.243634] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 5
633[ 1.243659] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
634[ 1.243694] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003
635[ 1.243697] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
636[ 1.243699] usb usb5: Product: xHCI Host Controller
637[ 1.243700] usb usb5: Manufacturer: Linux 4.4.196-1-Manjaro-ARM xhci-hcd
638[ 1.243702] usb usb5: SerialNumber: xhci-hcd.3.auto
639[ 1.243901] hub 5-0:1.0: USB hub found
640[ 1.243911] hub 5-0:1.0: 1 port detected
641[ 1.246416] ehci-platform fe380000.usb: EHCI Host Controller
642[ 1.246491] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 6
643[ 1.246571] ehci-platform fe380000.usb: irq 27, io mem 0xfe380000
644[ 1.254670] xhci-hcd xhci-hcd.2.auto: Host not halted after 16000 microseconds.
645[ 1.254672] xhci-hcd xhci-hcd.2.auto: Host controller not halted, aborting reset.
646[ 1.254723] xhci-hcd xhci-hcd.2.auto: USB bus 3 deregistered
647[ 1.262129] mmcblk1: mmc1:0001 DA4128 116 GiB
648[ 1.262770] mmcblk1boot0: mmc1:0001 DA4128 partition 1 4.00 MiB
649[ 1.263476] mmcblk1boot1: mmc1:0001 DA4128 partition 2 4.00 MiB
650[ 1.264207] mmcblk1rpmb: mmc1:0001 DA4128 partition 3 16.0 MiB
651[ 1.265946] dwmmc_rockchip fe320000.dwmmc: All phases work, using default phase 0.
652[ 1.266633] mmc0: new ultra high speed SDR50 SDHC card at address aaaa
653[ 1.267586] mmcblk0: mmc0:aaaa SS16G 14.8 GiB
654[ 1.269977] mmcblk0: p1
655[ 1.270662] mmcblk1: p1 p2
656[ 1.279546] usb 1-1: new high-speed USB device number 2 using ehci-platform
657[ 1.285633] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
658[ 1.287031] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
659[ 1.287644] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
660[ 1.288273] usb usb6: Product: EHCI Host Controller
661[ 1.288708] usb usb6: Manufacturer: Linux 4.4.196-1-Manjaro-ARM ehci_hcd
662[ 1.289291] usb usb6: SerialNumber: fe380000.usb
663[ 1.290032] hub 6-0:1.0: USB hub found
664[ 1.290370] hub 6-0:1.0: 1 port detected
665[ 1.291177] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
666[ 1.291904] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 3
667[ 1.292663] ohci-platform fe3a0000.usb: irq 28, io mem 0xfe3a0000
668[ 1.348222] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
669[ 1.348838] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
670[ 1.349471] usb usb3: Product: Generic Platform OHCI controller
671[ 1.349998] usb usb3: Manufacturer: Linux 4.4.196-1-Manjaro-ARM ohci_hcd
672[ 1.350590] usb usb3: SerialNumber: fe3a0000.usb
673[ 1.351932] hub 3-0:1.0: USB hub found
674[ 1.352298] hub 3-0:1.0: 1 port detected
675[ 1.354338] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
676[ 1.355013] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
677[ 1.355621] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
678[ 1.356154] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 24,32 bit host data width,256o
679[ 1.357342] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
680[ 1.368834] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div )
681[ 1.380871] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized
682[ 1.382255] rockchip-dmc dmc: Failed to get leakage
683[ 1.383393] rockchip-dmc dmc: could not find power_model node
684[ 1.427158] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
685[ 1.429196] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
686[ 1.431229] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
687[ 1.434482] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
688[ 1.438356] mmc2: queuing unknown CIS tuple 0x81 (9 bytes)
689[ 1.490091] mmc_host mmc2: Bus speed (slot 0) = 84500000Hz (slot req 90000000Hz, actual 84500000H)
690[ 1.497755] dwmmc_rockchip fe310000.dwmmc: All phases work, using default phase 0.
691[ 1.500149] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
692[ 1.500663] mmc2: new ultra high speed SDR104 SDIO card at address 0001
693[ 1.507897] asoc-simple-card speaker-sound: ES8316 HiFi <-> ff890000.i2s mapping ok
694[ 1.508737] es8316 1-0011: ASoC: Failed to create Left Hp mixer debugfs file
695[ 1.509357] es8316 1-0011: ASoC: Failed to create Right Hp mixer debugfs file
696[ 1.509999] es8316 1-0011: ASoC: Failed to create HPCP L debugfs file
697[ 1.510618] es8316 1-0011: ASoC: Failed to create HPCP R debugfs file
698[ 1.511243] es8316 1-0011: ASoC: Failed to create HPVOL L debugfs file
699[ 1.511861] es8316 1-0011: ASoC: Failed to create HPVOL R debugfs file
700[ 1.513211] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
701[ 1.513815] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
702[ 1.514440] usb 1-1: Product: USB2.0 Hub
703[ 1.515942] hub 1-1:1.0: USB hub found
704[ 1.516647] hub 1-1:1.0: 4 ports detected
705[ 1.518258] rockchip-drm display-subsystem: devfreq is ready
706[ 1.519354] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff800907b7e0)
707[ 1.520417] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff800907b7e0)
708[ 1.521450] rockchip-dp ff970000.edp: no DP phy configured
709[ 1.522938] rockchip-drm display-subsystem: bound ff970000.edp (ops 0xffffff8009073be8)
710[ 1.524531] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Not connected. Disabling cdn
711[ 1.525258] rockchip-drm display-subsystem: bound fec00000.dp (ops 0xffffff80090726f0)
712[ 1.525960] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
713[ 1.526543] [drm] No driver support for vblank timestamp query.
714[ 1.527275] rockchip-drm display-subsystem: failed to parse loader memory
715[ 1.531937] rockchip-vop ff900000.vop: [drm:vop_crtc_enable] Update mode to 1024x768p60, type: 14
716[ 1.553775] rockchip-dp ff970000.edp: [drm:analogix_dp_link_start] Enable downspread on the sink
717[ 1.555283] rockchip-dp ff970000.edp: Link Training Clock Recovery success
718[ 1.556707] rockchip-dp ff970000.edp: Link Training success!
719[ 1.718270] vendor storage:20160801 ret = 0
720[ 1.773786] Console: switching to colour frame buffer device 128x48
721[ 1.819632] rockchip-drm display-subsystem: fb0: frame buffer device
722[ 1.826728] rk-hdmi-dp-sound hdmi-dp-sound: i2s-hifi <-> ff8a0000.i2s mapping ok
723[ 1.827393] hdmi-audio-codec hdmi-audio-codec.5.auto: ASoC: Failed to create Playback debugfs file
724[ 1.829100] dhd_module_init: in Dongle Host Driver, version 1.579.77.41.10 (r)
725[ 1.829649] input: gpio-keys as /devices/platform/gpio-keys/input/input0
726[ 1.830335] ======== dhd_wlan_init_plat_data ========
727[ 1.830784] dhd_wlan_init_gpio: WL_REG_ON=-1
728[ 1.831157] dhd_wifi_platform_load: Enter
729[ 1.831515] rk808-rtc rk808-rtc: setting system clock to 2019-11-04 19:44:37 UTC (1572896677)
730[ 1.831525] Power-up adapter 'DHD generic adapter'
731[ 1.832749] of_cfs_init
732[ 1.832993] of_cfs_init: OK
733[ 1.836393] wifi_platform_set_power = 1
734[ 1.836756] ======== PULL WL_REG_ON(-1) HIGH! ========
735[ 1.837206] [WLAN_RFKILL]: rockchip_wifi_power: 1
736[ 1.837623] [WLAN_RFKILL]: wifi turn on power. -1
737[ 1.842997] ALSA device list:
738[ 1.843263] #0: es8316-spk-sound
739[ 1.843566] #1: rk-hdmi-dp-sound
740[ 1.844649] md: Waiting for all devices to be available before autodetect
741[ 1.845244] md: If you don't use raid, use raid=noautodetect
742[ 1.846161] md: Autodetecting RAID arrays.
743[ 1.846531] md: Scanned 0 and added 0 devices.
744[ 1.846919] md: autorun ...
745[ 1.847164] md: ... autorun DONE.
746[ 1.851044] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities
747[ 1.852279] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities
748[ 1.855461] mmcblk0: retrying because a re-tune was needed
749[ 1.869024] dwmmc_rockchip fe320000.dwmmc: All phases work, using default phase 0.
750[ 1.872313] mmcblk0: retrying because a re-tune was needed
751[ 1.872898] usb 3-1: new low-speed USB device number 2 using ohci-platform
752[ 1.885589] usb 1-1.2: new high-speed USB device number 3 using ehci-platform
753[ 1.887108] dwmmc_rockchip fe320000.dwmmc: All phases work, using default phase 0.
754[ 1.894561] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
755[ 1.895298] VFS: Mounted root (ext4 filesystem) on device 179:129.
756[ 1.897875] mmcblk0: retrying because a re-tune was needed
757[ 1.911935] dwmmc_rockchip fe320000.dwmmc: All phases work, using default phase 0.
758[ 1.912976] devtmpfs: mounted
759[ 1.913770] Freeing unused kernel memory: 1216K
760[ 1.920998] mmcblk0: retrying because a re-tune was needed
761[ 1.934578] dwmmc_rockchip fe320000.dwmmc: All phases work, using default phase 0.
762[ 2.112272] usb 1-1.2: New USB device found, idVendor=0c45, idProduct=6321
763[ 2.112909] usb 1-1.2: New USB device strings: Mfr=2, Product=1, SerialNumber=0
764[ 2.113556] usb 1-1.2: Product: USB Camera
765[ 2.113918] usb 1-1.2: Manufacturer: Sonix Technology Co., Ltd.
766[ 2.117746] uvcvideo: Found UVC 1.00 device USB Camera (0c45:6321)
767[ 2.138595] wifi_platform_bus_enumerate device present 1
768[ 2.139078] ======== Card detection to detect SDIO card! ========
769[ 2.139633] mmc2:mmc host rescan start!
770[ 2.156081] bcmsdh_register: register client driver
771[ 2.156655] bcmsdh_sdmmc_probe: Enter num=1
772[ 2.158458] bcmsdh_sdmmc_probe: Enter num=2
773[ 2.158867] bus num (host idx)=2, slot num (rca)=1
774[ 2.159290] found adapter info 'DHD generic adapter'
775[ 2.159766] sdioh_attach: set sd_f2_blocksize 256
776[ 2.160197] sdioh_attach: sd clock rate = 0
777[ 2.160840] dhdsdio_probe : no mutex held. set lock
778[ 2.161326] F1 signature read @0x18000000=0x15294345
779[ 2.164284] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 pkg:0x2
780[ 2.165306] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
781[ 2.165975] dhd_conf_set_chiprev: chip=0x4345, chiprev=9
782[ 2.169810] usb 3-1: New USB device found, idVendor=258a, idProduct=001e
783[ 2.170399] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
784[ 2.171049] usb 3-1: Product: USB KEYBOARD
785[ 2.171411] usb 3-1: Manufacturer: HAILUCK CO.,LTD
786[ 2.172459] CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211
787[ 2.174252] CFG80211-ERROR) wl_init_prof : wl_init_prof: No profile
788[ 2.175137] wl_escan_attach: Enter
789[ 2.175462] wl_escan_init: Enter
790[ 2.176209] wl_create_event_handler(): thread:wl_escan_handler:ae started
791[ 2.176289] tsk Enter, tsk = 0xffffffc0f11701b0
792[ 2.177556] dhd_attach(): thread:dhd_watchdog_thread:af started
793[ 2.178327] dhd_attach(): thread:dhd_dpc:b0 started
794[ 2.179136] dhd_attach(): thread:dhd_rxf:b1 started
795[ 2.179676] dhd_deferred_work_init: work queue initialized
796[ 2.180208] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2
797[ 2.181857] input: HAILUCK CO.,LTD USB KEYBOARD as /devices/platform/fe3a0000.usb/usb3/3-1/3-1:1.1
798[ 2.183147] dhd_bus_set_default_min_res_mask: Unhandled chip id
799[ 2.184065] sdioh_cis_read: func_cis_ptr[0]=0x10ac
800[ 2.190140] Dongle Host Driver, version 1.579.77.41.10 (r)
801[ 2.191170] wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0
802[ 2.191665] Register interface [wlan0] MAC: 6c:21:a2:e8:32:8b
803[ 2.191665]
804[ 2.192619] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 0
805[ 2.193199] dhd_wl_ioctl: returning as busstate=0
806[ 2.193630] dhd_dbg_detach_pkt_monitor, 2204
807[ 2.194005] dhd_bus_devreset: == Power OFF ==
808[ 2.194546] dhd_txglom_enable: enable 0
809[ 2.194885] dhd_conf_set_txglom_params: txglom_mode=copy
810[ 2.195350] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0
811[ 2.195950] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1
812[ 2.196556] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=-1
813[ 2.197148] dhd_bus_devreset: WLAN OFF DONE
814[ 2.197709] wifi_platform_set_power = 0
815[ 2.198047] ======== PULL WL_REG_ON(-1) LOW! ========
816[ 2.198498] [WLAN_RFKILL]: rockchip_wifi_power: 0
817[ 2.199004] [WLAN_RFKILL]: wifi shut off power.
818[ 2.199425] dhdsdio_probe : the lock is released.
819[ 2.200133] bcmsdh_sdmmc: probe of mmc2:0001:3 failed with error -110
820[ 2.200847] dhd_module_init: Exit err=0
821[ 2.234454] hid-generic 0003:258A:001E.0001: input,hidraw0: USB HID v1.10 Keyboard [HAILUCK CO.,L0
822[ 2.270984] systemd[1]: Failed to find module 'autofs4'
823[ 2.272984] cgroup: cgroup2: unknown option "nsdelegate"
824[ 2.273169] input: HAILUCK CO.,LTD USB KEYBOARD Touchpad as /devices/platform/fe3a0000.usb/usb3/32
825[ 2.285969] systemd[1]: systemd 243.78-1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA )
826[ 2.288521] systemd[1]: Detected architecture arm64.
827
828Welcome to Manjaro ARM!
829
830[ 2.303360] systemd[1]: Set hostname to <Manjaro>.
831[ 2.324130] hid-multitouch 0003:258A:001E.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [HAILU1
832[ 2.339202] mmcblk0: retrying because a re-tune was needed
833[ 2.342626] random: nonblocking pool is initialized
834[ 2.353889] dwmmc_rockchip fe320000.dwmmc: All phases work, using default phase 0.
835[ 2.724622] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system .
836[ 2.725724] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
837[ 2.727704] systemd[1]: Created slice system-getty.slice.
838[ OK ] Created slice system-getty.slice.
839[ 2.731310] systemd[1]: Created slice system-serial\x2dgetty.slice.
840[ OK ] Created slice system-serial\x2dgetty.slice.
841[ 2.735151] systemd[1]: Created slice User and Session Slice.
842[ OK ] Created slice User and Session Slice.
843[ 2.737835] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
844[ OK ] Started Dispatch Password ��…ts to Console Directory Watch.
845[ 2.740741] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
846[ OK ] Started Forward Password R��…uests to Wall Directory Watch.
847[ 2.743682] systemd[1]: Starting of Arbitrary Executable File Formats File System Automount Point.
848[UNSUPP] Starting of Arbitrary Exec��…Automount Point not supported.
849[ 2.746670] systemd[1]: Reached target Local Encrypted Volumes.
850[ OK ] Reached target Local Encrypted Volumes.
851[ 2.749683] systemd[1]: Reached target Paths.
852[ OK ] Reached target Paths.
853[ 2.751615] systemd[1]: Reached target Remote Encrypted Volumes.
854[ OK ] Reached target Remote Encrypted Volumes.
855[ 2.754600] systemd[1]: Reached target Remote File Systems.
856[ OK ] Reached target Remote File Systems.
857[ 2.757602] systemd[1]: Reached target Slices.
858[ OK ] Reached target Slices.
859[ 2.759628] systemd[1]: Reached target Swap.
860[ OK ] Reached target Swap.
861[ 2.761865] systemd[1]: Listening on Device-mapper event daemon FIFOs.
862[ OK ] Listening on Device-mapper event daemon FIFOs.
863[ 2.772865] systemd[1]: Listening on Process Core Dump Socket.
864[ OK ] Listening on Process Core Dump Socket.
865[ 2.775881] systemd[1]: Listening on initctl Compatibility Named Pipe.
866[ OK ] Listening on initctl Compatibility Named Pipe.
867[ 2.793474] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
868[ 2.794815] systemd[1]: Listening on Journal Socket (/dev/log).
869[ OK ] Listening on Journal Socket (/dev/log).
870[ 2.798057] systemd[1]: Listening on Journal Socket.
871[ OK ] Listening on Journal Socket.
872[ 2.801218] systemd[1]: Listening on Network Service Netlink Socket.
873[ OK ] Listening on Network Service Netlink Socket.
874[ 2.806022] systemd[1]: Listening on udev Control Socket.
875[ OK ] Listening on udev Control Socket.
876[ 2.808926] systemd[1]: Listening on udev Kernel Socket.
877[ OK ] Listening on udev Kernel Socket.
878[ 2.812011] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
879[ 2.815279] systemd[1]: Mounting POSIX Message Queue File System...
880 Mounting POSIX Message Queue File System...
881[ 2.821602] systemd[1]: Mounting Kernel Debug File System...
882 Mounting Kernel Debug File System...
883[ 2.828926] systemd[1]: Mounting Temporary Directory (/tmp)...
884 Mounting Temporary Directory (/tmp)...
885[ 2.834775] systemd[1]: Starting Create list of static device nodes for the current kernel...
886 Starting Create list of st��…odes for the current kernel...
887[ 2.838264] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skippe.
888[ 2.841174] systemd[1]: Condition check resulted in Load Kernel Modules being skipped.
889[ 2.844467] systemd[1]: Mounting FUSE Control File System...
890 Mounting FUSE Control File System...
891[ 2.850867] systemd[1]: Mounting Kernel Configuration File System...
892 Mounting Kernel Configuration File System...
893[ 2.856582] systemd[1]: Starting Remount Root and Kernel File Systems...
894 Starting Remount Root and Kernel File Systems...
895[ 2.862338] systemd[1]: Starting Apply Kernel Variables...
896 Starting Apply Kernel Variables...
897[ 2.867377] systemd[1]: Starting udev Coldplug all Devices...
898 Starting udev Coldplug all Devices...
899[ 2.874486] systemd[1]: Mounted POSIX Message Queue File System.
900[ OK ] Mounted POSIX Message Queue File System.
901[ 2.878462] systemd[1]: Mounted Kernel Debug File System.
902[ OK ] Mounted Kernel Debug File System.
903[ 2.882570] systemd[1]: Mounted Temporary Directory (/tmp).
904[ OK ] Mounted Temporary Directory (/tmp).
905[ 2.887264] systemd[1]: Started Create list of static device nodes for the current kernel.
906[ OK ] Started Create list of sta�… nodes for the current kernel.
907[ 2.893623] systemd[1]: Mounted FUSE Control File System.
908[ OK ] Mounted FUSE Control File System.
909[ 2.896056] systemd[1]: Mounted Kernel Configuration File System.
910[ OK ] Mounted Kernel Configuration File System.
911[ 2.900217] systemd[1]: Started Remount Root and Kernel File Systems.
912[ OK ] Started Remount Root and Kernel File Systems.
913[ 2.905220] systemd[1]: Started Apply Kernel Variables.
914[ OK ] Started Apply Kernel Variables.
915[ 2.914074] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
916[ 2.917583] systemd[1]: Starting Load/Save Random Seed...
917 Starting Load/Save Random Seed...
918[ 2.920947] systemd[1]: Condition check resulted in Create System Users being skipped.
919[ 2.924771] systemd[1]: Starting Create Static Device Nodes in /dev...
920 Starting Create Static Device Nodes in /dev...
921[ 2.968794] systemd[1]: Started Load/Save Random Seed.
922[ OK ] Started Load/Save Random Seed.
923[ 2.982092] systemd[1]: Started Create Static Device Nodes in /dev.
924[ OK ] Started Create Static Device Nodes in /dev.
925[ 2.985209] systemd[1]: Reached target Local File Systems (Pre).
926[ OK ] Reached target Local File Systems (Pre).
927[ 2.986948] systemd[1]: Condition check resulted in Virtual Machine and Container Storage (Compat.
928[ 2.987980] systemd[1]: Reached target Local File Systems.
929[ OK ] Reached target Local File Systems.
930[ 2.990780] systemd[1]: Reached target Containers.
931[ OK ] Reached target Containers.
932[ 2.997253] systemd[1]: Started Entropy Daemon based on the HAVEGE algorithm.
933[ OK ] Started Entropy Daemon based on the HAVEGE algorithm.
934[ 3.001067] systemd[1]: Condition check resulted in Rebuild Dynamic Linker Cache being skipped.
935[ 3.002039] systemd[1]: Condition check resulted in Store a System Token in an EFI Variable being.
936[ 3.006852] systemd[1]: Starting Journal Service...
937 Starting Journal Service...
938[ 3.009935] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being s.
939[ 3.014091] systemd[1]: Starting udev Kernel Device Manager...
940 Starting udev Kernel Device Manager...
941[ 3.072757] mmcblk0: retrying because a re-tune was needed
942[ 3.088083] dwmmc_rockchip fe320000.dwmmc: All phases work, using default phase 0.
943[ 3.097810] systemd[1]: Started udev Coldplug all Devices.
944[ OK ] Started udev Coldplug all Devices.
945[ 3.236296] mmcblk0: retrying because a re-tune was needed
946[ 3.250511] dwmmc_rockchip fe320000.dwmmc: All phases work, using default phase 0.
947[ 3.291692] systemd[1]: Started udev Kernel Device Manager.
948[ OK ] Started udev Kernel Device Manager.
949[ 3.299337] systemd[1]: Starting Network Service...
950 Starting Network Service...
951[ 3.441457] systemd[1]: Started Journal Service.
952[ OK ] Started Journal Service.
953 Starting Flush Journal to Persistent Storage...
954[ 3.469841] mmcblk0: retrying because a re-tune was needed
955[ 3.484889] dwmmc_rockchip fe320000.dwmmc: All phases work, using default phase 0.
956[ 3.489206] systemd-journald[207]: Received client request to flush runtime journal.
957[ 3.492841] mmcblk0: retrying because a re-tune was needed
958[ 3.507453] dwmmc_rockchip fe320000.dwmmc: All phases work, using default phase 0.
959[ OK ] Started Flush Journal to Persistent Storage.
960 Starting Create Volatile Files and Directories...
961[ OK ] Created slice system-systemd\x2dbacklight.slice.
962 Starting Load/Save Screen ��… of backlight:edp-backlight...
963[ OK ] Started Load/Save Screen B��…ss of backlight:edp-backlight.
964[ OK ] Found device /dev/ttyS2.
965[ 3.645006] ff100000.saradc supply vref not found, using dummy regulator
966[ OK ] Started Create Volatile Files and Directories.
967[ 3.733982] rockchip-pcie f8000000.pcie: no vpcie12v regulator found
968[ 3.734617] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
969[ 3.735187] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
970[ 3.739334] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
971[ 3.739909] rockchip-pcie f8000000.pcie: missing optional "memory-region" property
972[ 3.740595] rockchip-pcie f8000000.pcie: missing optional "rockchip,dma_trx_enabled" property
973[ 3.741344] rockchip-pcie f8000000.pcie: missing optional "rockchip,deferred" property
974[ 3.742055] rockchip-pcie f8000000.pcie: calling really probe
975[ 3.742565] rockchip-pcie f8000000.pcie: PCIe asserting reset
976[ 3.743836] rockchip-pcie f8000000.pcie: advertising gen2/1 training
977[ 3.744422] rockchip-pcie f8000000.pcie: PCIe reset released
978[ OK ] Reached target Sound Card.
979[ OK ] Listening on Load/Save RF ��…itch Status /dev/rfkill Watch.
980 Starting Network Time Synchronization...
981 Starting Update UTMP about System Boot/Shutdown...
982 Starting Load/Save RF Kill Switch Status...
983[ OK ] Started Update UTMP about System Boot/Shutdown.
984[ OK ] Started Network Service.
985[ OK ] Reached target Network.
986[ 3.913053] [BT_RFKILL]: Enter rfkill_rk_set_power
987[ 3.913485] [BT_RFKILL]: Set blocked:1
988[ 3.913855] [BT_RFKILL]: bt shut off power
989[ OK ] Started Load/Save RF Kill Switch Status.
990[ OK ] Started Network Time Synchronization.
991[ OK ] Reached target System Initialization.
992[ OK ] Started Daily Cleanup of Temporary Directories.
993[ OK ] Reached target System Time Set.
994[ OK ] Reached target System Time Synchronized.
995[ OK ] Started Daily verification of password and group files.
996[ OK ] Reached target Timers.
997[ OK ] Listening on D-Bus System Message Bus Socket.
998[ OK ] Reached target Sockets.
999[ OK ] Reached target Basic System.
1000[ OK ] Started D-Bus System Message Bus.
1001 Starting Login Service...
1002 Starting Permit User Sessions...
1003[ 4.204969] mali ff9a0000.gpu: leakage=16
1004[ 4.216917] mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0
1005[ 4.217576] mali ff9a0000.gpu: Protected mode not available
1006[ 4.219461] mali ff9a0000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
1007[ 4.220136] mali ff9a0000.gpu: Using configured power model mali-simple-power-model, and fallbackl
1008[ 4.221197] I : [File] : drivers/gpu/arm/midgard/backend/gpu/mali_kbase_devfreq.c; [Line] : 431; .
1009[ 4.222958] mali ff9a0000.gpu: Probed as mali0
1010[ 4.245682] rockchip-pcie f8000000.pcie: PCIe link training gen1 timed out.
1011[ 4.246307] rockchip-pcie f8000000.pcie: init port failed
1012[ 4.246820] rockchip-pcie f8000000.pcie: probe init failed
1013[ 4.247318] rockchip-pcie f8000000.pcie: PCIe probe failed.
1014[ 4.248024] rockchip-pcie: probe of f8000000.pcie failed with error -110
1015[ OK ] Started Permit User Sessions.
1016[ OK ] Started Getty on tty1.
1017[ OK ] Started Serial Getty on ttyS2.
1018[ OK ] Reached target Login Prompts.
1019[ OK ] Started Login Service.
1020[ OK ] Reached target Multi-User System.
1021[ OK ] Reached target Graphical Interface.
1022
1023Manjaro Linux 4.4.196-1-Manjaro-ARM (ttyS2)