· 6 years ago · Nov 09, 2019, 07:24 PM
1-Boot 2019.01-1-00035-g64abfc9b6b (Jan 11 2019 - 19:47:34 +0000) Arch Linux ARM
2
3CPU: Allwinner A64 (SUN50I)
4Model: Pine64+
5DRAM: 2 GiB
6MMC: SUNXI SD/MMC: 0
7Loading Environment from FAT... Unable to use mmc 0:1... In: serial
8Out: vidconsole
9Err: vidconsole
10Net: phy interface7
11eth0: ethernet@1c30000
12starting USB...
13USB0: USB EHCI 1.00
14USB1: USB OHCI 1.0
15USB2: USB EHCI 1.00
16USB3: USB OHCI 1.0
17scanning bus 0 for devices... 1 USB Device(s) found
18scanning bus 2 for devices... 3 USB Device(s) found
19 scanning usb for storage devices... 0 Storage Device(s) found
20Hit any key to stop autoboot: 0
21switch to partitions #0, OK
22mmc0 is current device
23Scanning mmc 0:1...
24Found U-Boot script /boot.scr
25963 bytes read in 6 ms (156.3 KiB/s)
26## Executing script at 4fc00000
2726673664 bytes read in 1210 ms (21 MiB/s)
28** File not found initrd.img **
2924932 bytes read in 9 ms (2.6 MiB/s)
30## Flattened Device Tree blob at 4fa00000
31 Booting using the fdt blob at 0x4fa00000
32EHCI failed to shut down host controller.
33EHCI failed to shut down host controller.
34 Loading Ramdisk to 4868f000, end 49fff200 ... OK
35 Loading Device Tree to 0000000048685000, end 000000004868e163 ... OK
36
37Starting kernel ...
38
39[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
40[ 0.000000] Linux version 4.20.0-1-ARCH (alarm@rock64) (gcc version 8.2.0 (GCC)) #1 SMP Fri Jan 11 12:06:48 PST 2019
41[ 0.000000] Machine model: Pine64+
42[ 0.000000] efi: Getting EFI parameters from FDT:
43[ 0.000000] efi: UEFI not found.
44[ 0.000000] Reserved memory: created CMA memory pool at 0x00000000ba000000, size 64 MiB
45[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
46[ 0.000000] psci: probing for conduit method from DT.
47[ 0.000000] psci: PSCIv1.1 detected in firmware.
48[ 0.000000] psci: Using standard PSCI v0.2 function IDs
49[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
50[ 0.000000] psci: SMC Calling Convention v1.1
51[ 0.000000] random: get_random_bytes called from start_kernel+0x9c/0x458 with crng_init=0
52[ 0.000000] percpu: Embedded 36 pages/cpu @(____ptrval____) s109464 r8192 d29800 u147456
53[ 0.000000] Detected VIPT I-cache on CPU0
54[ 0.000000] CPU features: enabling workaround for ARM erratum 843419
55[ 0.000000] Speculative Store Bypass Disable mitigation not required
56[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
57[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 508032
58[ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait f0
59[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
60[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
61[ 0.000000] Memory: 1893000K/2064384K available (13628K kernel code, 2240K rwdata, 8628K rodata, 1472K init, 16898K)
62[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
63[ 0.000000] ftrace: allocating 47818 entries in 187 pages
64[ 0.000000] rcu: Hierarchical RCU implementation.
65[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
66[ 0.000000] Tasks RCU enabled.
67[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
68[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
69[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
70[ 0.000000] GIC: Using split EOI/Deactivate mode
71[ 0.000000] arch_timer: Enabling global workaround for Allwinner A64 timer instability
72[ 0.000000] arch_timer: CPU0: Trapping CNTVCT access
73[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
74[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 44079520259s
75[ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
76[ 0.000511] Console: colour dummy device 80x25
77[ 0.000552] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
78[ 0.000565] pid_max: default: 32768 minimum: 301
79[ 0.000760] LSM: Security Framework initializing
80[ 0.000770] Yama: becoming mindful.
81[ 0.000859] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
82[ 0.000882] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
83[ 0.002466] ASID allocator initialised with 32768 entries
84[ 0.002564] rcu: Hierarchical SRCU implementation.
85[ 0.005788] EFI services will not be available.
86[ 0.006074] smp: Bringing up secondary CPUs ...
87[ 0.007478] Detected VIPT I-cache on CPU1
88[ 0.007535] arch_timer: CPU1: Trapping CNTVCT access
89[ 0.007545] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
90[ 0.008645] Detected VIPT I-cache on CPU2
91[ 0.008675] arch_timer: CPU2: Trapping CNTVCT access
92[ 0.008683] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
93[ 0.009658] Detected VIPT I-cache on CPU3
94[ 0.009686] arch_timer: CPU3: Trapping CNTVCT access
95[ 0.009694] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
96[ 0.009775] smp: Brought up 1 node, 4 CPUs
97[ 0.009806] SMP: Total of 4 processors activated.
98[ 0.009815] CPU features: detected: 32-bit EL0 Support
99[ 0.009823] CPU features: detected: CRC32 instructions
100[ 0.012773] CPU: All CPU(s) started at EL2
101[ 0.012794] alternatives: patching kernel code
102[ 0.014523] devtmpfs: initialized
103[ 0.020856] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
104[ 0.020878] futex hash table entries: 1024 (order: 4, 65536 bytes)
105[ 0.023432] pinctrl core: initialized pinctrl subsystem
106[ 0.024468] DMI not present or invalid.
107[ 0.024886] NET: Registered protocol family 16
108[ 0.026294] cpuidle: using governor ladder
109[ 0.026406] cpuidle: using governor menu
110[ 0.026695] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
111[ 0.026707] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
112[ 0.028322] DMA: preallocated 256 KiB pool for atomic allocations
113[ 0.028854] Serial: AMBA PL011 UART driver
114[ 0.047340] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
115[ 0.047652] cryptd: max_cpu_qlen set to 1000
116[ 0.048470] ACPI: Interpreter disabled.
117[ 0.049055] vgaarb: loaded
118[ 0.049864] SCSI subsystem initialized
119[ 0.050236] usbcore: registered new interface driver usbfs
120[ 0.050292] usbcore: registered new interface driver hub
121[ 0.050369] usbcore: registered new device driver usb
122[ 0.050674] pps_core: LinuxPPS API ver. 1 registered
123[ 0.050681] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
124[ 0.050699] PTP clock support registered
125[ 0.050872] EDAC MC: Ver: 3.0.0
126[ 0.051418] Advanced Linux Sound Architecture Driver Initialized.
127[ 0.051925] NetLabel: Initializing
128[ 0.051933] NetLabel: domain hash size = 128
129[ 0.051938] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
130[ 0.052007] NetLabel: unlabeled traffic allowed by default
131[ 0.052499] clocksource: Switched to clocksource arch_sys_counter
132[ 0.174465] VFS: Disk quotas dquot_6.6.0
133[ 0.174565] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
134[ 0.175450] pnp: PnP ACPI: disabled
135[ 0.183041] NET: Registered protocol family 2
136[ 0.183689] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes)
137[ 0.183734] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
138[ 0.183894] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
139[ 0.184218] TCP: Hash tables configured (established 16384 bind 16384)
140[ 0.184350] UDP hash table entries: 1024 (order: 3, 32768 bytes)
141[ 0.184412] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
142[ 0.184626] NET: Registered protocol family 1
143[ 0.185238] RPC: Registered named UNIX socket transport module.
144[ 0.185245] RPC: Registered udp transport module.
145[ 0.185251] RPC: Registered tcp transport module.
146[ 0.185257] RPC: Registered tcp NFSv4.1 backchannel transport module.
147[ 0.185456] Unpacking initramfs...
148[ 0.185470] Initramfs unpacking failed: junk in compressed archive
149[ 0.203940] Freeing initrd memory: 26048K
150[ 0.204769] kvm [1]: 8-bit VMID
151[ 0.204781] kvm [1]: IPA Size Limit: 40bits
152[ 0.207752] kvm [1]: vgic interrupt IRQ1
153[ 0.207882] kvm [1]: Hyp mode initialized successfully
154[ 0.242775] Initialise system trusted keyrings
155[ 0.242943] workingset: timestamp_bits=46 max_order=19 bucket_order=0
156[ 0.249189] zbud: loaded
157[ 0.251523] NFS: Registering the id_resolver key type
158[ 0.251549] Key type id_resolver registered
159[ 0.251556] Key type id_legacy registered
160[ 0.251570] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
161[ 0.251764] SGI XFS with ACLs, security attributes, no debug enabled
162[ 1.906805] NET: Registered protocol family 38
163[ 1.906829] Key type asymmetric registered
164[ 1.906837] Asymmetric key parser 'x509' registered
165[ 1.906907] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
166[ 1.907043] io scheduler noop registered
167[ 1.907052] io scheduler deadline registered
168[ 1.907263] io scheduler cfq registered (default)
169[ 1.907271] io scheduler mq-deadline registered
170[ 1.907279] io scheduler kyber registered
171[ 1.907560] atomic64_test: passed
172[ 1.908389] sun50i-de2-bus 1000000.de2: Error couldn't map SRAM to device
173[ 1.909100] sun4i-usb-phy 1c19400.phy: failed to get clock usb0_phy
174[ 1.914145] sun50i-a64-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
175[ 1.916035] IPMI message handler: version 39.2
176[ 1.926949] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
177[ 1.929133] msm_serial: driver initialized
178[ 1.937575] libphy: Fixed MDIO Bus: probed
179[ 1.938612] usbcore: registered new interface driver asix
180[ 1.938656] usbcore: registered new interface driver ax88179_178a
181[ 1.940039] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
182[ 1.940055] ehci-pci: EHCI PCI platform driver
183[ 1.940101] ehci-platform: EHCI generic platform driver
184[ 1.940318] ehci-platform 1c1a000.usb: EHCI Host Controller
185[ 1.940487] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
186[ 1.941380] ehci-platform 1c1a000.usb: irq 13, io mem 0x01c1a000
187[ 1.962518] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
188[ 1.962739] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.20
189[ 1.962750] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
190[ 1.962758] usb usb1: Product: EHCI Host Controller
191[ 1.962767] usb usb1: Manufacturer: Linux 4.20.0-1-ARCH ehci_hcd
192[ 1.962775] usb usb1: SerialNumber: 1c1a000.usb
193[ 1.963247] hub 1-0:1.0: USB hub found
194[ 1.963282] hub 1-0:1.0: 1 port detected
195[ 1.963937] ehci-orion: EHCI orion driver
196[ 1.964130] tegra-ehci: Tegra EHCI driver
197[ 1.964238] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
198[ 1.964257] ohci-pci: OHCI PCI platform driver
199[ 1.964343] ohci-platform: OHCI generic platform driver
200[ 1.964489] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
201[ 1.964643] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
202[ 1.964917] ohci-platform 1c1a400.usb: irq 14, io mem 0x01c1a400
203[ 2.036804] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.20
204[ 2.036815] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
205[ 2.036824] usb usb2: Product: Generic Platform OHCI controller
206[ 2.036833] usb usb2: Manufacturer: Linux 4.20.0-1-ARCH ohci_hcd
207[ 2.036841] usb usb2: SerialNumber: 1c1a400.usb
208[ 2.037332] hub 2-0:1.0: USB hub found
209[ 2.037368] hub 2-0:1.0: 1 port detected
210[ 2.037965] uhci_hcd: USB Universal Host Controller Interface driver
211[ 2.038640] usbcore: registered new interface driver uas
212[ 2.038736] usbcore: registered new interface driver usb-storage
213[ 2.038771] usbcore: registered new interface driver ums-alauda
214[ 2.038806] usbcore: registered new interface driver ums-cypress
215[ 2.038840] usbcore: registered new interface driver ums-datafab
216[ 2.038874] usbcore: registered new interface driver ums_eneub6250
217[ 2.038907] usbcore: registered new interface driver ums-freecom
218[ 2.038949] usbcore: registered new interface driver ums-isd200
219[ 2.038984] usbcore: registered new interface driver ums-jumpshot
220[ 2.039018] usbcore: registered new interface driver ums-karma
221[ 2.039052] usbcore: registered new interface driver ums-onetouch
222[ 2.039097] usbcore: registered new interface driver ums-realtek
223[ 2.039132] usbcore: registered new interface driver ums-sddr09
224[ 2.039166] usbcore: registered new interface driver ums-sddr55
225[ 2.039207] usbcore: registered new interface driver ums-usbat
226[ 2.039305] usbcore: registered new interface driver usbserial_generic
227[ 2.039336] usbserial: USB Serial support registered for generic
228[ 2.040844] mousedev: PS/2 mouse device common for all mice
229[ 2.041773] sun6i-rtc 1f00000.rtc: rtc core: registered rtc-sun6i as rtc0
230[ 2.041782] sun6i-rtc 1f00000.rtc: RTC enabled
231[ 2.043904] device-mapper: uevent: version 1.0.3
232[ 2.044203] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
233[ 2.045539] sdhci: Secure Digital Host Controller Interface driver
234[ 2.045547] sdhci: Copyright(c) Pierre Ossman
235[ 2.046163] Synopsys Designware Multimedia Card Interface Driver
236[ 2.047132] sdhci-pltfm: SDHCI platform and OF driver helper
237[ 2.048077] ledtrig-cpu: registered to indicate activity on CPUs
238[ 2.048524] hidraw: raw HID events driver (C) Jiri Kosina
239[ 2.048658] usbcore: registered new interface driver usbhid
240[ 2.048664] usbhid: USB HID core driver
241[ 2.050538] thermal thermal_zone0: failed to read out thermal zone (-110)
242[ 2.050581] thermal thermal_zone1: failed to read out thermal zone (-110)
243[ 2.050605] thermal thermal_zone2: failed to read out thermal zone (-110)
244[ 2.052418] drop_monitor: Initializing network drop monitor service
245[ 2.052696] Initializing XFRM netlink socket
246[ 2.053359] NET: Registered protocol family 10
247[ 2.055420] Segment Routing with IPv6
248[ 2.055505] mip6: Mobile IPv6
249[ 2.055518] NET: Registered protocol family 17
250[ 2.055595] Key type dns_resolver registered
251[ 2.056370] registered taskstats version 1
252[ 2.056377] Loading compiled-in X.509 certificates
253[ 2.056529] zswap: loaded using pool lzo/zbud
254[ 2.056736] Key type big_key registered
255[ 2.057819] Key type encrypted registered
256[ 2.078617] sun4i-drm display-engine: bound 1100000.mixer (ops sun8i_mixer_ops)
257[ 2.088000] sun4i-drm display-engine: bound 1200000.mixer (ops sun8i_mixer_ops)
258[ 2.088408] sun4i-drm display-engine: No panel or bridge found... RGB output disabled
259[ 2.088424] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops sun4i_tcon_ops)
260[ 2.088594] sun4i-drm display-engine: bound 1c0d000.lcd-controller (ops sun4i_tcon_ops)
261[ 2.088652] sun8i-dw-hdmi 1ee0000.hdmi: Couldn't get regulator
262[ 2.088674] sun4i-drm display-engine: failed to bind 1ee0000.hdmi (ops sun8i_dw_hdmi_ops): -517
263[ 2.088952] sun4i-drm display-engine: Couldn't bind all pipelines components
264[ 2.089086] sun4i-drm display-engine: master bind failed: -517
265[ 2.089866] sunxi-rsb 1f03400.rsb: RSB running at 3000000 Hz
266[ 2.090261] axp20x-rsb sunxi-rsb-3a3: AXP20x variant AXP803 found
267[ 2.093692] dcdc1: supplied by regulator-dummy
268[ 2.094025] dcdc2: supplied by regulator-dummy
269[ 2.094244] dcdc4: supplied by regulator-dummy
270[ 2.094464] dcdc5: supplied by regulator-dummy
271[ 2.094708] dcdc6: supplied by regulator-dummy
272[ 2.094927] dc1sw: supplied by regulator-dummy
273[ 2.095115] aldo1: supplied by regulator-dummy
274[ 2.095374] aldo2: supplied by regulator-dummy
275[ 2.095598] aldo3: supplied by regulator-dummy
276[ 2.095814] dldo1: supplied by regulator-dummy
277[ 2.096066] dldo2: supplied by regulator-dummy
278[ 2.096134] vcc-mipi: Bringing 2900000uV into 3300000-3300000uV
279[ 2.096338] dldo3: supplied by regulator-dummy
280[ 2.096565] dldo4: supplied by regulator-dummy
281[ 2.096815] eldo1: supplied by regulator-dummy
282[ 2.097036] eldo2: supplied by regulator-dummy
283[ 2.097258] eldo3: supplied by regulator-dummy
284[ 2.097512] fldo1: supplied by regulator-dummy
285[ 2.097750] fldo2: supplied by regulator-dummy
286[ 2.097994] rtc-ldo: supplied by regulator-dummy
287[ 2.098197] ldo-io0: supplied by regulator-dummy
288[ 2.098438] ldo-io1: supplied by regulator-dummy
289[ 2.099734] axp20x-adc axp813-adc: DMA mask not set
290[ 2.101058] axp20x-battery-power-supply axp20x-battery-power-supply: DMA mask not set
291[ 2.101936] axp20x-ac-power-supply axp20x-ac-power-supply: DMA mask not set
292[ 2.102063] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded
293[ 2.106599] sun50i-a64-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
294[ 2.107430] printk: console [ttyS0] disabled
295[ 2.128008] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 24, base_baud = 1500000) is a U6_16550A
296[ 2.164191] thermal thermal_zone2: failed to read out thermal zone (-110)
297[ 2.172208] thermal thermal_zone2: failed to read out thermal zone (-110)
298[ 3.564237] printk: console [ttyS0] enabled
299[ 3.590273] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 25, base_baud = 1500000) is a U6_16550A
300[ 3.599354] serial serial0: tty port ttyS1 registered
301[ 3.605595] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
302[ 3.611429] dwmac-sun8i 1c30000.ethernet: Linked as a consumer to regulator.6
303[ 3.618884] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 6 (expect 0)
304[ 3.627515] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
305[ 3.634739] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
306[ 3.641951] dwmac-sun8i 1c30000.ethernet: COE Type 2
307[ 3.646921] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
308[ 3.653709] dwmac-sun8i 1c30000.ethernet: Normal descriptors
309[ 3.659361] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
310[ 3.665168] libphy: stmmac: probed
311[ 3.670862] ehci-platform 1c1b000.usb: EHCI Host Controller
312[ 3.676669] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3
313[ 3.685016] ehci-platform 1c1b000.usb: irq 15, io mem 0x01c1b000
314[ 3.712528] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00
315[ 3.718825] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.20
316[ 3.727096] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
317[ 3.734339] usb usb3: Product: EHCI Host Controller
318[ 3.739211] usb usb3: Manufacturer: Linux 4.20.0-1-ARCH ehci_hcd
319[ 3.745222] usb usb3: SerialNumber: 1c1b000.usb
320[ 3.750242] hub 3-0:1.0: USB hub found
321[ 3.754035] hub 3-0:1.0: 1 port detected
322[ 3.759224] ohci-platform 1c1b400.usb: Generic Platform OHCI controller
323[ 3.766022] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 4
324[ 3.774055] ohci-platform 1c1b400.usb: irq 16, io mem 0x01c1b400
325[ 3.846730] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.20
326[ 3.855002] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
327[ 3.862215] usb usb4: Product: Generic Platform OHCI controller
328[ 3.868154] usb usb4: Manufacturer: Linux 4.20.0-1-ARCH ohci_hcd
329[ 3.874165] usb usb4: SerialNumber: 1c1b400.usb
330[ 3.879150] hub 4-0:1.0: USB hub found
331[ 3.882938] hub 4-0:1.0: 1 port detected
332[ 3.888194] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regular
333[ 3.898959] usb_phy_generic usb_phy_generic.0.auto: Linked as a consumer to regulator.0
334[ 3.907403] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
335[ 3.913342] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 5
336[ 3.921319] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.20
337[ 3.929594] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
338[ 3.936820] usb usb5: Product: MUSB HDRC host driver
339[ 3.941779] usb usb5: Manufacturer: Linux 4.20.0-1-ARCH musb-hcd
340[ 3.947788] usb usb5: SerialNumber: musb-hdrc.1.auto
341[ 3.953165] hub 5-0:1.0: USB hub found
342[ 3.956937] hub 5-0:1.0: 1 port detected
343[ 3.962743] cpu cpu0: Linked as a consumer to regulator.2
344[ 3.968187] cpu cpu0: Dropping the link to regulator.2
345[ 3.973488] cpu cpu0: Linked as a consumer to regulator.2
346[ 3.979750] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 792000 KHz
347[ 3.990241] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 816000 KHz
348[ 4.000116] sunxi-mmc 1c0f000.mmc: Linked as a consumer to regulator.1
349[ 4.010159] sunxi-mmc 1c0f000.mmc: Got CD GPIO
350[ 4.039851] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
351[ 4.050014] sunxi-mmc 1c10000.mmc: Linked as a consumer to regulator.13
352[ 4.056709] sunxi-mmc 1c10000.mmc: Linked as a consumer to regulator.14
353[ 4.068169] sunxi-mmc 1c10000.mmc: allocated mmc-pwrseq
354[ 4.098737] sunxi-mmc 1c10000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
355[ 4.108088] simple-framebuffer be000000.framebuffer: Linked as a consumer to regulator.10
356[ 4.116293] simple-framebuffer be000000.framebuffer: framebuffer at 0xbe000000, 0x7e9000 bytes, mapped to 0x(____pt)
357[ 4.127516] simple-framebuffer be000000.framebuffer: format=x8r8g8b8, mode=1920x1080x32, linelength=7680
358[ 4.170742] Console: switching to colour frame buffer device 240x67
359[ 4.170821] usb 3-1: new high-speed USB device number 2 using ehci-platform
360[ 4.212323] simple-framebuffer be000000.framebuffer: fb0: simplefb registered!
361[ 4.228452] sun4i-drm display-engine: bound 1100000.mixer (ops sun8i_mixer_ops)
362[ 4.243777] sun4i-drm display-engine: bound 1200000.mixer (ops sun8i_mixer_ops)
363[ 4.251515] sun4i-drm display-engine: No panel or bridge found... RGB output disabled
364[ 4.259363] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops sun4i_tcon_ops)
365[ 4.267427] mmc0: new high speed SDHC card at address aaaa
366[ 4.273947] mmcblk0: mmc0:aaaa SS16G 14.8 GiB
367[ 4.278719] sun4i-drm display-engine: bound 1c0d000.lcd-controller (ops sun4i_tcon_ops)
368[ 4.287255] sun8i-dw-hdmi 1ee0000.hdmi: Linked as a consumer to regulator.10
369[ 4.298229] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a with HDCP (sun8i_dw_hdmi_phy)
370[ 4.307842] mmcblk0: p1 p2
371[ 4.311578] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus driver
372[ 4.319732] sun4i-drm display-engine: bound 1ee0000.hdmi (ops sun8i_dw_hdmi_ops)
373[ 4.327156] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
374[ 4.333779] [drm] No driver support for vblank timestamp query.
375[ 4.339703] fb0: switching to sun4i-drm-fb from simple
376[ 4.344941] Console: switching to colour dummy device 80x25
377[ 4.403172] usb 3-1: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11
378[ 4.411360] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
379[ 4.418511] usb 3-1: Product: USB 2.0 Hub
380[ 4.426136] hub 3-1:1.0: USB hub found
381[ 4.430025] random: fast init done
382[ 4.433455] hub 3-1:1.0: 4 ports detected
383[ 4.852532] usb 3-1.3: new low-speed USB device number 3 using ehci-platform
384[ 4.937542] Console: switching to colour frame buffer device 240x67
385[ 4.982807] sun4i-drm display-engine: fb0: DRM emulated frame buffer device
386[ 4.993348] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
387[ 5.001203] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01 00:00:11 UTC (11)
388[ 5.009474] ALSA device list:
389[ 5.012437] No soundcards found.
390[ 5.016094] md: Waiting for all devices to be available before autodetect
391[ 5.022889] md: If you don't use raid, use raid=noautodetect
392[ 5.029009] md: Autodetecting RAID arrays.
393[ 5.033141] md: autorun ...
394[ 5.035929] md: ... autorun DONE.
395[ 5.070713] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
396[ 5.078276] VFS: Mounted root (ext4 filesystem) on device 179:2.
397[ 5.096919] devtmpfs: mounted
398[ 5.107715] Freeing unused kernel memory: 1472K
399[ 5.110423] usb 3-1.3: New USB device found, idVendor=1c4f, idProduct=0002, bcdDevice= 1.10
400[ 5.120622] usb 3-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
401[ 5.120643] Run /sbin/init as init process
402[ 5.127953] usb 3-1.3: Product: USB Keyboard
403[ 5.136304] usb 3-1.3: Manufacturer: SIGMACHIP
404[ 5.150647] input: SIGMACHIP USB Keyboard as /devices/platform/soc/1c1b000.usb/usb3/3-1/3-1.3/3-1.3:1.0/0003:1C4F:00
405[ 5.233108] hid-generic 0003:1C4F:0002.0001: input,hidraw0: USB HID v1.10 Keyboard [SIGMACHIP USB Keyboard] on usb-0
406[ 5.249517] input: SIGMACHIP USB Keyboard Consumer Control as /devices/platform/soc/1c1b000.usb/usb3/3-1/3-1.3/3-1.1
407[ 5.332883] input: SIGMACHIP USB Keyboard System Control as /devices/platform/soc/1c1b000.usb/usb3/3-1/3-1.3/3-1.3:2
408[ 5.346789] hid-generic 0003:1C4F:0002.0002: input,hidraw1: USB HID v1.10 Device [SIGMACHIP USB Keyboard] on usb-1c1
409[ 5.737667] systemd[1]: System time before build time, advancing clock.
410[ 5.779150] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +)
411[ 5.800886] systemd[1]: Detected architecture arm64.
412
413Welcome to Ubuntu 18.04.2 LTS!
414
415[ 5.856805] systemd[1]: Set hostname to <bpi-m64>.
416[ 6.248678] random: systemd: uninitialized urandom read (16 bytes read)
417[ 6.255640] systemd[1]: Reached target Swap.
418[ OK ] Reached target Swap.
419[ 6.282794] random: systemd: uninitialized urandom read (16 bytes read)
420[ 6.289675] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
421[ OK ] Started Forward Password Requests to Wall Directory Watch.
422[ 6.323035] random: systemd: uninitialized urandom read (16 bytes read)
423[ 6.330290] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
424[ OK ] Set up automount Arbitrary Executab…rmats File System Automount Point.
425[ 6.373569] systemd[1]: Created slice User and Session Slice.
426[ OK ] Created slice User and Session Slice.
427[ 6.405870] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
428[ OK ] Started Dispatch Password Requests to Console Directory Watch.
429[ 6.442617] systemd[1]: Reached target Paths.
430[ OK ] Reached target Paths.
431[ 6.473620] systemd[1]: Created slice System Slice.
432[ OK ] Created slice System Slice.
433[ OK ] Created slice system-getty.slice.
434[ OK ] Listening on udev Control Socket.
435[ OK ] Listening on RPCbind Server Activation Socket.
436[ OK ] Listening on fsck to fsckd communication Socket.
437[ OK ] Listening on udev Kernel Socket.
438[ OK ] Listening on Journal Socket.
439 Starting Load Kernel Modules...
440 Mounting Huge Pages File System...
441 Mounting Kernel Debug File System...
442 Mounting POSIX Message Queue File System...
443 Starting Create Static Device Nodes in /dev...
444 Starting udev Coldplug all Devices...
445 Mounting RPC Pipe File System...
446[ OK ] Created slice system-serial\x2dgetty.slice.
447 Starting Remount Root and Kernel File Systems...
448[ OK ] Listening on Journal Socket (/dev/log).
449[ 7.028383] EXT4-fs (mmcblk0p2): re-mounted. Opts: commit=600,errors=remount-ro
450[ OK ] Reached target Slices.
451 Starting Journal Service...
452[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
453[ OK ] Created slice system-systemd\x2dfsck.slice.
454[ OK ] Reached target Local Encrypted Volumes.
455[ OK ] Started Load Kernel Modules.
456[ OK ] Mounted Huge Pages File System.
457[ OK ] Mounted Kernel Debug File System.
458[ OK ] Started Journal Service.
459[ OK ] Mounted POSIX Message Queue File System.
460[ OK ] Started Create Static Device Nodes in /dev.
461[ OK ] Mounted RPC Pipe File System.
462[ OK ] Started Remount Root and Kernel File Systems.
463 Starting Load/Save Random Seed...
464 Starting udev Kernel Device Manager...
465[ OK ] Reached target Local File Systems (Pre).
466 Starting Flush Journal to Persistent Storage...
467 Starting Apply Kernel Variables...
468 Mounting Kernel Configuration File System...
469[ OK ] Started udev Coldplug all Devices.
470[ OK ] Started udev Kernel Device Manager.
471[ OK ] Started Load/Save Random Seed.
472[ OK ] Started Apply Kernel Variables.
473[ OK ] Mounted Kernel Configuration File System.
474[ OK ] Started Flush Journal to Persistent Storage.
475[ OK ] Found device /dev/ttyS0.
476[ OK ] Found device /dev/mmcblk0p1.
477 Starting File System Check on /dev/mmcblk0p1...
478[ OK ] Started File System Check Daemon to report status.
479[ OK ] Found device /sys/subsystem/net/devices/eth0.
480[ OK ] Started File System Check on /dev/mmcblk0p1.
481 Mounting /boot...disks (100.0% complete)
482[ OK ] Mounted /boot.
483[ OK ] Reached target Local File Systems.
484[ OK ] Started ifup for eth0.
485 Starting Preprocess NFS configuration...
486 Starting Create Volatile Files and Directories...
487 Starting Raise network interfaces...
488[ OK ] Started Preprocess NFS configuration.
489[ OK ] Reached target NFS client services.
490[ OK ] Started Create Volatile Files and Directories.
491 Starting RPC bind portmap service...
492 Starting Network Name Resolution...
493 Starting Network Time Synchronization...
494 Starting Update UTMP about System Boot/Shutdown...
495[ OK ] Started Raise network interfaces.
496[ OK ] Started Update UTMP about System Boot/Shutdown.
497[ OK ] Started RPC bind portmap service.
498[ OK ] Reached target RPC Port Mapper.
499[ OK ] Reached target Remote File Systems (Pre).
500[ OK ] Reached target Remote File Systems.
501[ OK ] Started Network Name Resolution.
502[ OK ] Started Network Time Synchronization.
503[ OK ] Reached target System Time Synchronized.
504[ OK ] Reached target System Initialization.
505[ OK ] Started Discard unused blocks once a week.
506[ OK ] Started Message of the Day.
507[ OK ] Started Daily Cleanup of Temporary Directories.
508[ OK ] Listening on D-Bus System Message Bus Socket.
509[ OK ] Started Daily apt download activities.
510[ OK ] Started Daily apt upgrade and clean activities.
511[ OK ] Reached target Timers.
512[ OK ] Listening on lircd.socket.
513[ OK ] Reached target Sockets.
514[ OK ] Reached target Basic System.
515[ OK ] Started Deferred execution scheduler.
516 Starting Dispatcher daemon for systemd-networkd...
517[ OK ] Started Convert IR remotes button p…ses to mouse movements and clicks.
518[ OK ] Started D-Bus System Message Bus.
519[ OK ] Started Set the CPU Frequency Scaling governor.
520 Starting WPA supplicant...
521 Starting Initializes zram swaping...
522 Starting Login Service...
523 Starting lircd(8) initialization helper tool...
524[ OK ] Started Handle events from IR remotes decoded by lircd(8).
525[ OK ] Reached target Host and Network Name Lookups.
526[FAILED] Failed to start Initializes zram swaping.
527See 'systemctl status zram-config.service' for details.
528[ OK ] Started WPA supplicant.
529[ OK ] Started Login Service.
530[ OK ] Reached target Network.
531 Starting OpenBSD Secure Shell server...
532 Starting Permit User Sessions...
533[ OK ] Started Permit User Sessions.
534[ OK ] Started Serial Getty on ttyS0.
535[ OK ] Started Getty on tty1.
536[ OK ] Reached target Login Prompts.
537[ OK ] Started OpenBSD Secure Shell server.
538[ OK ] Started lircd(8) initialization helper tool.
539[ OK ] Started Flexible IR remote input/output application support.
540[ OK ] Started Forward LIRC button presses as uinput events.
541[ OK ] Started Dispatcher daemon for systemd-networkd.
542[ OK ] Reached target Multi-User System.
543[ OK ] Reached target Graphical Interface.
544 Starting Update UTMP about System Runlevel Changes...
545[ OK ] Started Update UTMP about System Runlevel Changes.
546
547Ubuntu 18.04.2 LTS bpi-m64 ttyS0
548
549
550Ubuntu 18.04.2 LTS bpi-m64 ttyS0
551
552bpi-m64 login:
553Ubuntu 18.04.2 LTS bpi-m64 ttyS0
554
555bpi-m64 login: ubuntu
556Password:
557Last login: Tue Jul 9 19:56:18 -03 2019 on tty1
558Welcome to Ubuntu 18.04.2 LTS (GNU/Linux 4.20.0-1-ARCH aarch64)
559
560 * Documentation: https://help.ubuntu.com
561 * Management: https://landscape.canonical.com
562 * Support: https://ubuntu.com/advantage
563
564 * MicroK8s 1.15 is out! It has already been installed on more
565 than 14 different distros. Guess which ones?
566
567 https://snapcraft.io/microk8s
568This system has been minimized by removing packages and content that are
569not required on a system that users do not log into.
570
571To restore this content, you can run the 'unminimize' command.
572ubuntu@bpi-m64:~$ lsb_release -rs
57318.04
574ubuntu@bpi-m64:~$ lsb_release -r
575Release: 18.04
576ubuntu@bpi-m64:~$ lsb_release
577No LSB modules are available.
578ubuntu@bpi-m64:~$ lsb_release -a
579No LSB modules are available.
580Distributor ID: Ubuntu
581Description: Ubuntu 18.04.2 LTS
582Release: 18.04
583Codename: bionic
584ubuntu@bpi-m64:~$