· 6 years ago · May 24, 2019, 06:58 AM
1HELO
2CPUI
3L1CI
4PLLI
5PMCB
6HELO
7CPUI
8L1CI
94.1404Apatch1-1.0.38-117.134
10DRAM
11----
12PHYS
13ZQDN
14PHYE
15DINT
16TST1
17TST2
18PASS
19----
20ZBSS
21L12F
22MAIN
23FPS0
24NAN9
25NAN3
26RFS0
27NAN5
28
29
30Base: 4.14_04Apatch1
31CFE version 1.0.38-117.134 for BCM96838 (32bit,SP,BE)
32Build Date: Thu Mar 31 17:58:23 CST 2016 (adam@Ubuntu)
33Copyright (C) 2000-2013 Broadcom Corporation.
34
35Chip ID: BCM68380_B0, MIPS: 600MHz, DDR: 533MHz, Bus: 240MHz
36RDP: 800MHz
37Main Thread: TP0
38Total Memory: 268435456 bytes (256MB)
39Boot Address: 0xbfc00000
40
41NAND flash device: , id 0xc2f1 block 128KB size 131072KB
42ddr_tm_base_address = 0xa0800000
43f_initialize_bbh_dma_sdma_related_arrays:(956) errorenable IH Wan-Wan forwarding...
44Initializing port 0
45Initializing port 1
46Initializing port 2
47Initializing port 3
48oren_data_path_go done!!!
49Correctable ECC Error detected: addr=0x0002da00, intrCtrl=0x00000090, accessCtrl=0xF7441010
50Correctable ECC Error detected: addr=0x03ddfe00, intrCtrl=0x00000090, accessCtrl=0xF7441010
51Correctable ECC Error detected: addr=0x03ec9400, intrCtrl=0x00000090, accessCtrl=0xF7441010
52Correctable ECC Error detected: addr=0x04072a00, intrCtrl=0x00000090, accessCtrl=0xF7441010
53Correctable ECC Error detected: addr=0x041fce00, intrCtrl=0x00000090, accessCtrl=0xF7441010
54Uncorrectable ECC Error: addr=0x04272000, blk=531,
55â–’Uncorrectable ECC Error: addr=0x04272400, blk=531,
56Uncorrectable ECC Error: addr=0x04272600, blk=531,
57Board IP address : 192.168.1.1:ffffff00
58Host IP address : 192.168.1.100
59Gateway IP address :
60Run from flash/host/tftp (f/h/c) : f
61Default host run file name : vmlinux
62Default host flash file name : bcm963xx_fs_kernel
63Boot delay (0-9 seconds) : 1
64Default host ramdisk file name :
65Default ramdisk store address :
66 Uncorrectable ECC Error: addr=0x00000400, blk=0,
67Uncorrectable ECC Error: addr=0x00000600, blk=0,
68Uncorrectable ECC Error: addr=0x00000800, blk=0,
69JUncorrectable ECC Error: addr=0x00000000, blk=0,
70Uncorrectable ECC Error: addr=0x00000200, blk=0,
71Uncorrectable ECC Error: addr=0x00000400, blk=0,
72Uncorrectable ECC Error: addr=0x00000600, blk=0,
73Uncorrectable ECC Error: addr=0x00000800, blk=0,
74Uncorrectable ECC Error: addr=0x00000a00, blk=0,
75Uncorrectable ECC Error: addr=0x00000c00, blk=0,
76Uncorrectable ECC Error: addr=0x00000e00, blk=0,
77Uncorrectable ECC Error: addr=0x00001000, blk=0,
78Uncorrectable ECC Error: addr=0x00001200, blk=0,
79Uncorrectable ECC Error: addr=0x00001400, blk=0,
80Uncorrectable ECC Error: addr=0x00001600, blk=0,
81Uncorrectable ECC Error: addr=0x00001800, blk=0,
82Uncorrectable ECC Error: addr=0x00001a00, blk=0,
83Uncorrectable ECC Error: addr=0x00001c00, blk=0,
84*Uncorrectable ECC Error: addr=0x00002000, blk=0,
85Uncorrectable ECC Error: addr=0x00002200, blk=0,
86Uncorrectable ECC Error: addr=0x00002400, blk=0,
87Uncorrectable ECC Error: addr=0x00002a00, blk=0,,
88Uncorrectable ECC Error: addr=0x00003200, blk=0,
89Uncorrectable ECC Error: addr=0x00003400, blk=0,
90Uncorrectable ECC Error: addr=0x00003800, blk=0,
91Uncorrectable ECC Error: addr=0x00003a00, blk=0,
92Uncorrectable ECC Error: addr=0x00003c00, blk=0,â–’
93 Uncorrectable ECC Error: addr=0x00003e00, blk=0,
94Uncorrectable ECC Error: addr=0x00004000, blk=0,
95â–’Board Id (0-25) : 0, blk=0,
96Number of MAC Addresses (1-32) : 10
97Base MAC Address : 00:10:18:00:00:00
98PSI Size (1-64) KBytes : 24
99Enable Backup PSI [0|1] : 0
100System Log Size (0-256) KBytes : 0
101Auxillary File System Size Percent: 0
102Main Thread Number [0|1] : 0
103MC memory allocation (MB) : 0
104TM memory allocation (MB) : 0
105
106Creating CPU ring for queue number 0 with 32 packets descriptor=0x80674514
107 Done initializing Ring 0 Base=0xa220f9b0K End=0xa220fbb0K calculated entries= 32 RDD Base=0x0220f9b0K descriptor=0x80674514
108Open PHY 1 on MAC 0 : link state = Down
109Open PHY 2 on MAC 1 : link state = Down
110Open PHY 3 on MAC 2 : link state = Down
111Open PHY 4 on MAC 3 : link state = Down
112DEBUG: Nand Partition Table Magic Found at 160000.
113*** Press any key to stop auto run (1 seconds) ***
114â–’uto run second count down: 0
115***************************************************
116 Boot Version 1.0.1.0
117
118***************************************************
119Entering Firmware : Everything is OK.
120Boot Flag's Magic Found at 6800000.
121Find bootFlag(eRcOmM.011) successfully.
122Decompression OK!t image (0xbffe0000) ...
123Entry at 0x8046a7d0
124Closing network.
125Starting program at 0x8046a7d0
126Linux version 3.4.11-rt19 (root@ubuntu) (gcc version 4.6.2 (Buildroot 2011.11) ) #2 SMP PREEMPT Wed Jan 16 18:09:40 CST 2019
127
128*** Board is not initialized properly ***
129
130
131*** Voice Board id is not initialized properly ***
132
133 prom init
134CPU revision is: 0002a080 (Broadcom BMIPS4350)
135#######
136tmsize size 36700160
137#######
138mcsize size 4194304
139#######
140dhd0 size 0
141#######
142dhd1 size 0
143#######
144dhd2 size 0
145Determined physical RAM map:
146 memory: 00100000 @ 0ff00000 (usable)
147 memory: 02300000 @ 0dc00000 (reserved)
148 memory: 00400000 @ 0d800000 (reserved)
149 memory: 00004000 @ 0d7fc000 (reserved)
150 memory: 0d7fc000 @ 00000000 (usable)
151Zone PFN ranges:
152 DMA 0x00000000 -> 0x00001000
153 Normal 0x00001000 -> 0x00010000
154Movable zone start PFN for each node
155Early memory PFN ranges
156 0: 0x00000000 -> 0x00010000
157On node 0 totalpages: 65536
158free_area_init_node: node 0, pgdat 8059ed30, node_mem_map 81000000
159 DMA zone: 32 pages used for memmap
160 DMA zone: 0 pages reserved
161 DMA zone: 4064 pages, LIFO batch:0
162 Normal zone: 480 pages used for memmap
163 Normal zone: 60960 pages, LIFO batch:15
164PERCPU: Embedded 7 pages/cpu @81203000 s5536 r8192 d14944 u32768
165pcpu-alloc: s5536 r8192 d14944 u32768 alloc=8*4096
166pcpu-alloc: [0] 0 [0] 1
167Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
168Kernel command line: ro noinitrd irqaffinity=0
169PID hash table entries: 1024 (order: 0, 4096 bytes)
170Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
171Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
172Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
173Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
174allocated 524288 bytes of page_cgroup
175please try 'cgroup_disable=memory' option if you don't want memory cgroups
176Memory: 213000k/222192k available (4518k kernel code, 9192k reserved, 1175k data, 224k init, 0k highmem)
177Preemptible hierarchical RCU implementation.
178NR_IRQS:256
179console [ttyS0] enabled
180Allocating memory for DSP module core and initialization code
181Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
182Calibrating delay loop... 598.01 BogoMIPS (lpj=299008)
183pid_max: default: 32768 minimum: 301
184Mount-cache hash table entries: 512
185--Kernel Config--
186 SMP=1
187 PREEMPT=1
188 DEBUG_SPINLOCK=0
189 DEBUG_MUTEXES=0
190Initializing cgroup subsys memory
191Initializing cgroup subsys devices
192Broadcom Logger v0.1 Jan 16 2019 16:44:53
193CPU revision is: 0002a080 (Broadcom BMIPS4350)
194Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
195Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
196Brought up 2 CPUs
197NET: Registered protocol family 16
198PMC Driver Init... done.
199registering PCI controller with io_map_base unset
200registering PCI controller with io_map_base unset
201registering PCI controller with io_map_base unset
202BpGetEthernetMacInfoArrayPtr : Cannot get EnetMacInfo - Error <3>
203ERROR:BoardID not Set in BoardParams
204bio: create slab <bio-0> at 0
205SCSI subsystem initialized
206usbcore: registered new interface driver usbfs
207usbcore: registered new interface driver hub
208usbcore: registered new device driver usb
209PCI host bridge to bus 0000:00
210pci_bus 0000:00: root bus resource [mem 0xeff00000-0xefffffff]
211pci_bus 0000:00: root bus resource [io 0xf1000000-0xf100ffff]
212pci 0000:00:09.0: [14e4:6300] type 00 class 0x0c0310
213pci 0000:00:09.0: reg 10: [mem 0x15400400-0x154004ff]
214pci 0000:00:0a.0: [14e4:6300] type 00 class 0x0c0320
215pci 0000:00:0a.0: reg 10: [mem 0x15400300-0x154003ff]
216PCI host bridge to bus 0000:01
217pci_bus 0000:01: root bus resource [mem 0xd0000000-0xdfffffff]
218pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
219pci 0000:01:00.0: [14e4:6838] type 01 class 0x060400
220pci 0000:01:00.0: PME# supported from D0 D3hot
221pci 0000:02:00.0: [14e4:a8db] type 00 class 0x028000
222pci 0000:02:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit]
223pci 0000:02:00.0: supports D1 D2
224pci 0000:01:00.0: Checking PCIe ASPM for vendor 14e4 device a8db
225pci 0000:01:00.0: BAR 8: assigned [mem 0xd0000000-0xd00fffff]
226pci 0000:02:00.0: BAR 0: assigned [mem 0xd0000000-0xd0007fff 64bit]
227pci 0000:01:00.0: PCI bridge to [bus 02-02]
228pci 0000:01:00.0: bridge window [mem 0xd0000000-0xd00fffff]
229PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
230PCI host bridge to bus 0000:03
231pci_bus 0000:03: root bus resource [mem 0xe0000000-0xefefffff]
232pci_bus 0000:03: root bus resource [??? 0x00000000 flags 0x0]
233pci 0000:03:00.0: [14e4:6838] type 01 class 0x060400
234pci 0000:03:00.0: PME# supported from D0 D3hot
235pci 0000:04:00.0: [14e4:4360] type 00 class 0x028000
236pci 0000:04:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit]
237pci 0000:04:00.0: supports D1 D2
238pci 0000:03:00.0: Checking PCIe ASPM for vendor 14e4 device 4360
239pci 0000:03:00.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
240pci 0000:04:00.0: BAR 0: assigned [mem 0xe0000000-0xe0007fff 64bit]
241pci 0000:03:00.0: PCI bridge to [bus 04-04]
242pci 0000:03:00.0: bridge window [mem 0xe0000000-0xe00fffff]
243PCI: Enabling device 0000:03:00.0 (0000 -> 0002)
244bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
245skbFreeTask created successfully
246gbpm_do_work scheduled
247BLOG v3.0 Initialized
248BLOG Rule v1.0 Initialized
249Broadcom IQoS v0.1 Jan 16 2019 16:56:06 initialized
250Broadcom GBPM v0.1 Jan 16 2019 16:56:07 initialized
251Switching to clocksource MIPS
252NET: Registered protocol family 2
253IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
254TCP established hash table entries: 8192 (order: 4, 65536 bytes)
255TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
256TCP: Hash tables configured (established 8192 bind 8192)
257TCP: reno registered
258UDP hash table entries: 128 (order: 0, 4096 bytes)
259UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
260NET: Registered protocol family 1
261PCI: CLS 16 bytes, default 16
262init_bcm_tstamp: unhandled mips_hpt_freq=300000000, adjust constants in bcm_tstamp.c
263bcm_tstamp initialized, (hpt_freq=300000000 2us_div=300 2ns_mult=0 2ns_shift=0)
264NTFS driver 2.1.30 [Flags: R/W].
265jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
266fuse init (API version 7.18)
267msgmni has been set to 416
268io scheduler noop registered (default)
269Broadcom NAND controller (BrcmNand Controller)
270mtd->oobsize=0, mtd->eccOobSize=0
271NAND_CS_NAND_XOR=00000000
272B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0
273brcmnand_read_id: CS0: dev_id=c2f18095
274After: NandSelect=40000001, nandConfig=15142200
275DevId c2f18095 may not be supported. Will use config info
276Spare Area Size = 16B/512B
277Block size=00020000, erase shift=17
278NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
279busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
280ECC level changed to 4
281OOB size changed to 16
282BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 128MB on CS0
283
284Found NAND on CS0: ACC=f7441010, cfg=15142200, flashId=c2f18095, tim1=6532845b, tim2=00001e94
285BrcmNAND version = 0x80000500 128MB @00000000
286brcmnand_scan: B4 nand_select = 40000001
287brcmnand_scan: After nand_select = 40000001
288handle_acc_control: default CORR ERR threshold 1 bits
289ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16
290page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
291Brcm NAND controller version = 5.0 NAND flash size 128MB @18000000
292ECC layout=brcmnand_oob_bch4_2k
293brcmnand_scan: mtd->oobsize=64
294brcmnand_scan: oobavail=35, eccsize=512, writesize=2048
295brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7
296-->brcmnand_default_bbt
297brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_des,.â–’Hâ–’â–’â–’block table Bbt0 found at page 0000ffc0, version 0xFF for chip on CS0
298 MBad block table 1tbB found at page 0000ff80, version 0x00 for chip on CS0
299brcmnand_reset_corr_threshold: default CORR ERR threshold 1 bits for CS0
300brcmnand_reset_corr_threshold: CORR ERR threshold changed to 3 bits for CS0
301nand_read_bbt: Bad block at 0x033e0000
302brcmnandCET: Status -> DefY.â–’â–’â–’â–’Kernel boot magic : 0;1;1
303Creating 13 MTD partitions on "brcmnand.0":
3040x000000000000-0x000000020000 : "CfeROM"
3050x000000020000-0x000000160000 : "CfeRAM"
3060x000000160000-0x000000200000 : "FlashMAP"
3070x000000200000-0x0000002a0000 : "SN"
3080x0000002a0000-0x0000003e0000 : "Protect"
3090x0000003e0000-0x0000021e0000 : "Rootfs1"
3100x0000021e0000-0x000003600000 : "Lib1"
3110x000003600000-0x000005400000 : "Rootfs2"
3120x000005400000-0x000006800000 : "Lib2"
3130x000006800000-0x000006940000 : "Bootflg"
3140x000006940000-0x000006bc0000 : "XMLConfig"
3150x000006bc0000-0x0000070c0000 : "AppData"
3160x000000000000-0x000000160000 : "Bootloader_Rom_Ram"
317PPP generic driver version 2.4.2
318PPP BSD Compression module registered
319PPP Deflate Compression module registered
320NET: Registered protocol family 24
321ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
322ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
323PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
324ehci_hcd 0000:00:0a.0: setting latency timer to 64
325ehci_hcd 0000:00:0a.0: EHCI Host Controller
326drivers/usb/core/inode.c: creating file 'devices'
327drivers/usb/core/inode.c: creating file '001'
328ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
329ehci_hcd 0000:00:0a.0: reset hcs_params 0x1212 dbg=0 cc=1 pcc=2 ordered ports=2
330ehci_hcd 0000:00:0a.0: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park
331ehci_hcd 0000:00:0a.0: park 0
332ehci_hcd 0000:00:0a.0: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
333ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
334ehci_hcd 0000:00:0a.0: ...powerup ports...
335ehci_hcd 0000:00:0a.0: MWI active
336ehci_hcd 0000:00:0a.0: supports USB remote wakeup
337ehci_hcd 0000:00:0a.0: irq 81, io mem 0x15400300
338ehci_hcd 0000:00:0a.0: init command 0010005 (park)=0 ithresh=1 period=512 RUN
339ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
340usb usb1: default language 0x0409
341usb usb1: udev 1, busnum 1, minor = 0
342[USB] Device 'EHCI Host Controller 0000:00:0a.0'is plugged into port 1.
343usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
344usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
345usb usb1: Product: EHCI Host Controller
346usb usb1: Manufacturer: Linux 3.4.11-rt19 ehci_hcd
347usb usb1: SerialNumber: 0000:00:0a.0
348usb usb1: usb_probe_device
349usb usb1: configuration #1 chosen from 1 choice
350usb usb1: adding 1-0:1.0 (config #1, interface 0)
351hub 1-0:1.0: usb_probe_interface
352hub 1-0:1.0: usb_probe_interface - got id
353hub 1-0:1.0: USB hub found
354hub 1-0:1.0: 2 ports detected
355hub 1-0:1.0: standalone hub
356hub 1-0:1.0: individual port power switching
357hub 1-0:1.0: individual port over-current protection
358hub 1-0:1.0: power on to power good time: 20ms
359hub 1-0:1.0: local power source is good
360hub 1-0:1.0: enabling power on all ports
361drivers/usb/core/inode.c: creating file '001'
362ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
363ohci_hcd: block sizes: ed 64 td 64
364PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
365ohci_hcd 0000:00:09.0: setting latency timer to 64
366ohci_hcd 0000:00:09.0: OHCI Host Controller
367drivers/usb/core/inode.c: creating file '002'
368ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
369ohci_hcd 0000:00:09.0: created debug files
370ohci_hcd 0000:00:09.0: irq 80, io mem 0x15400400
371hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
372ohci_hcd 0000:00:09.0: OHCI controller state
373ohci_hcd 0000:00:09.0: OHCI 1.0, NO legacy support registers, rh state running
374ohci_hcd 0000:00:09.0: control 0x083 HCFS=operational CBSR=3
375ohci_hcd 0000:00:09.0: cmdstatus 0x00000 SOC=0
376ohci_hcd 0000:00:09.0: intrstatus 0x00000004 SF
377ohci_hcd 0000:00:09.0: intrenable 0x8000005a MIE RHSC UE RD WDH
378ohci_hcd 0000:00:09.0: hcca frame #0005
379ohci_hcd 0000:00:09.0: roothub.a 02000202 POTPGT=2 NPS NDP=2(2)
380ohci_hcd 0000:00:09.0: roothub.b 00000000 PPCM=0000 DR=0000
381ohci_hcd 0000:00:09.0: roothub.status 00008000 DRWE
382ohci_hcd 0000:00:09.0: roothub.portstatus [0] 0x00000100 PPS
383ohci_hcd 0000:00:09.0: roothub.portstatus [1] 0x00000100 PPS
384usb usb2: default language 0x0409
385usb usb2: udev 1, busnum 2, minor = 128
386[USB] Device 'OHCI Host Controller 0000:00:09.0'is plugged into port 2.
387usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
388usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
389usb usb2: Product: OHCI Host Controller
390usb usb2: Manufacturer: Linux 3.4.11-rt19 ohci_hcd
391usb usb2: SerialNumber: 0000:00:09.0
392usb usb2: usb_probe_device
393usb usb2: configuration #1 chosen from 1 choice
394usb usb2: adding 2-0:1.0 (config #1, interface 0)
395hub 2-0:1.0: usb_probe_interface
396hub 2-0:1.0: usb_probe_interface - got id
397hub 2-0:1.0: USB hub found
398hub 2-0:1.0: 2 ports detected
399hub 2-0:1.0: standalone hub
400hub 2-0:1.0: no power switching (usb 1.0)
401hub 2-0:1.0: global over-current protection
402hub 2-0:1.0: power on to power good time: 4ms
403hub 2-0:1.0: local power source is good
404hub 2-0:1.0: no over-current condition exists
405hub 2-0:1.0: trying to enable port power on non-switchable hub
406drivers/usb/core/inode.c: creating file '001'
407usbcore: registered new interface driver usblp
408Initializing USB Mass Storage driver...
409usbcore: registered new interface driver usb-storage
410USB Mass Storage support registered.
411i2c /dev entries driver
412brcmboard: brcm_board_init entry
413CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 80310e14, ra == 80313a70
414Oops[#1]:
415Cpu 0
416$ 0 : 00000000 10009900 00000000 8060a290
417$ 4 : 000000d8 8d03be3c 00000103 8d03be30
418$ 8 : 682e1e55 682e1e55 ffffffff ffffffff
419$12 : ffffffff 00000001 ffffffff ffffffff
420$16 : 00000000 80610000 8d03be3c 00000000
421$20 : 00000000 8d03be34 8d03be32 8d03be30
422$24 : 00000000 00000c00
423$28 : 8d038000 8d03bdc8 00000000 80313a70
424Hi : 00000000
425Lo : 00000c00
426epc : 80310e14 BpGetElem+0xc/0x80
427 Not tainted
428ra : 80313a70 BpGetButtonInfo+0x64/0x2bc
429Status: 10009903 KERNEL EXL IE
430Cause : 00000008
431BadVA : 00000000
432PrId : 0002a080 (Broadcom BMIPS4350)
433Process swapper/0 (pid: 1, threadinfo=8d038000, task=8d035b08, tls=00000000)
434Stack : 0000007b 0000007c 0000007d 0000007e 00000103 80552ef0 00000000 8d391c00
435 00000000 80610000 80590000 80610000 805e0000 80552ef0 805a01b0 805e0000
436 00000055 805b3fd8 00000000 8d004c80 00000000 00000000 00000000 00000000
437 00000000 00000000 80590000 804fffff 80610000 00000000 805cbe84 804f0000
438 805d8000 00000000 00000000 80310268 0000005c 805b38d0 805cbe84 805e0000
439 ...
440Call Trace:
441[<805a01b0>] repair_env_string+0x0/0x94
442[<805b3fd8>] brcm_board_init+0x310/0xb28
443[<80310268>] i2cdev_attach_adapter+0x0/0x154
444[<805b38d0>] i2c_dev_init+0xa8/0xfc
445[<805b3cc8>] brcm_board_init+0x0/0xb28
446[<805a01b0>] repair_env_string+0x0/0x94
447[<80010560>] do_one_initcall+0x160/0x1f0
448[<805b1a10>] platform_bus_init+0x38/0x60
449[<805a0af8>] kernel_init+0x160/0x200
450[<805a01b0>] repair_env_string+0x0/0x94
451[<80015068>] kernel_thread_helper+0x10/0x18
452[<805a0998>] kernel_init+0x0/0x200
453[<80015058>] kernel_thread_helper+0x0/0x18
454
455
456Call Trace:
457[<80310e14>] BpGetElem+0xc/0x80
458[<80313a70>] BpGetButtonInfo+0x64/0x2bc
459[<805b3fd8>] brcm_board_init+0x310/0xb28
460[<80010560>] do_one_initcall+0x160/0x1f0
461
462
463Code: 8ca20000 1040001a 00000000 <8c430000> 24070103 10670011 00000000 1064000f 00000000
464hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
465---[ end trace 644a027a16fcd582 ]---
466====kmsg_dump====.
467Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
468
469====kmsg_dump====.
470Rebooting in 1 seconds..
471
472stopping CPU 1
473====kmsg_dump====.
474kerSysMipsSoftReset: called onâ–’