· 4 years ago · Sep 08, 2021, 08:18 AM
1Xilinx Zynq MP First Stage Boot Loader
2Release 2021.1 Jun 10 2021 - 10:37:42
3NOTICE: ATF running on XCZU9EG/silicon v4/RTL5.1 at 0xfffea000
4NOTICE: BL31: v2.4(release):v1.1-7609-g851523ea2
5NOTICE: BL31: Built : 08:27:07, Apr 28 2021
6
7
8U-Boot 2021.01 (Jun 01 2021 - 11:54:06 +0000)
9
10Model: ZynqMP ZCU102 Rev1.0
11Board: Xilinx ZynqMP
12DRAM: 4 GiB
13PMUFW: v1.1
14EL Level: EL2
15Chip ID: zu9eg
16NAND: 0 MiB
17MMC: mmc@ff170000: 0
18Loading Environment from FAT... *** Warning - bad CRC, using default environment
19
20In: serial
21Out: serial
22Err: serial
23Bootmode: LVL_SHFT_SD_MODE1
24Reset reason: EXTERNAL
25Net:
26ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 12, interface rgmii-id
27eth0: ethernet@ff0e0000
28Hit any key to stop autoboot: 0
29switch to partitions #0, OK
30mmc0 is current device
31Scanning mmc 0:1...
32Found U-Boot script /boot.scr
332594 bytes read in 13 ms (194.3 KiB/s)
34## Executing script at 20000000
35Trying to load boot images from mmc0
3621582336 bytes read in 1435 ms (14.3 MiB/s)
3740937 bytes read in 19 ms (2.1 MiB/s)
38## Flattened Device Tree blob at 00100000
39 Booting using the fdt blob at 0x100000
40 Loading Device Tree to 000000007dd06000, end 000000007dd12fe8 ... OK
41
42Starting kernel ...
43
44[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
45[ 0.000000] Linux version 5.10.0-xilinx-v2021.1 (oe-user@oe-host) (aarch64-xilinx-linux-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP Fri Jun 4 15:57:16 UTC 2021
46[ 0.000000] Machine model: ZynqMP ZCU102 Rev1.0
47[ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8')
48[ 0.000000] printk: bootconsole [cdns0] enabled
49[ 0.000000] efi: UEFI not found.
50[ 0.000000] cma: Reserved 1536 MiB at 0x000000001dc00000
51[ 0.000000] Zone ranges:
52[ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000ffffffff]
53[ 0.000000] Normal [mem 0x0000000100000000-0x000000087fffffff]
54[ 0.000000] Movable zone start for each node
55[ 0.000000] Early memory node ranges
56[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fefffff]
57[ 0.000000] node 0: [mem 0x0000000800000000-0x000000087fffffff]
58[ 0.000000] Zeroed struct page in unavailable ranges: 256 pages
59[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000087fffffff]
60[ 0.000000] psci: probing for conduit method from DT.
61[ 0.000000] psci: PSCIv1.1 detected in firmware.
62[ 0.000000] psci: Using standard PSCI v0.2 function IDs
63[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
64[ 0.000000] psci: SMC Calling Convention v1.2
65[ 0.000000] percpu: Embedded 22 pages/cpu s50968 r8192 d30952 u90112
66[ 0.000000] Detected VIPT I-cache on CPU0
67[ 0.000000] CPU features: detected: ARM erratum 845719
68[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1031940
69[ 0.000000] Kernel command line: earlycon console=ttyPS0,115200 clk_ignore_unused root=/dev/mmcblk0p2 rw rootwait cma=1536M
70[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
71[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
72[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
73[ 0.000000] software IO TLB: mapped [mem 0x0000000019c00000-0x000000001dc00000] (64MB)
74[ 0.000000] Memory: 2452288K/4193280K available (13952K kernel code, 980K rwdata, 3916K rodata, 2112K init, 588K bss, 168128K reserved, 1572864K cma-reserved)
75[ 0.000000] rcu: Hierarchical RCU implementation.
76[ 0.000000] rcu: RCU event tracing is enabled.
77[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
78[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
79[ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000
80[ 0.000000] GIC: Using split EOI/Deactivate mode
81[ 0.000000] irq-xilinx: mismatch in kind-of-intr param
82[ 0.000000] irq-xilinx: /amba_pl@0/interrupt-controller@80020000: num_irq=32, sw_irq=0, edge=0x1
83[ 0.000000] random: get_random_bytes called from start_kernel+0x31c/0x524 with crng_init=0
84[ 0.000000] arch_timer: cp15 timer(s) running at 100.00MHz (phys).
85[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x171024e7e0, max_idle_ns: 440795205315 ns
86[ 0.000003] sched_clock: 56 bits at 100MHz, resolution 10ns, wraps every 4398046511100ns
87[ 0.008387] Console: colour dummy device 80x25
88[ 0.012480] Calibrating delay loop (skipped), value calculated using timer frequency.. 200.00 BogoMIPS (lpj=400000)
89[ 0.022841] pid_max: default: 32768 minimum: 301
90[ 0.027563] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
91[ 0.034788] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
92[ 0.043593] rcu: Hierarchical SRCU implementation.
93[ 0.047618] EFI services will not be available.
94[ 0.051963] smp: Bringing up secondary CPUs ...
95[ 0.056686] Detected VIPT I-cache on CPU1
96[ 0.056724] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
97[ 0.057109] Detected VIPT I-cache on CPU2
98[ 0.057132] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
99[ 0.057494] Detected VIPT I-cache on CPU3
100[ 0.057517] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
101[ 0.057564] smp: Brought up 1 node, 4 CPUs
102[ 0.091779] SMP: Total of 4 processors activated.
103[ 0.096452] CPU features: detected: 32-bit EL0 Support
104[ 0.101556] CPU features: detected: CRC32 instructions
105[ 0.106693] CPU: All CPU(s) started at EL2
106[ 0.110735] alternatives: patching kernel code
107[ 0.116243] devtmpfs: initialized
108[ 0.124322] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
109[ 0.128417] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
110[ 0.173368] pinctrl core: initialized pinctrl subsystem
111[ 0.173863] DMI not present or invalid.
112[ 0.176937] NET: Registered protocol family 16
113[ 0.182269] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
114[ 0.188278] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
115[ 0.196108] audit: initializing netlink subsys (disabled)
116[ 0.201552] audit: type=2000 audit(0.144:1): state=initialized audit_enabled=0 res=1
117[ 0.209137] cpuidle: using governor menu
118[ 0.213088] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
119[ 0.219811] ASID allocator initialised with 65536 entries
120[ 0.225225] Serial: AMBA PL011 UART driver
121[ 0.256167] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
122[ 0.257236] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
123[ 0.263891] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
124[ 0.270551] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
125[ 1.321974] cryptd: max_cpu_qlen set to 1000
126[ 1.346701] DRBG: Continuing without Jitter RNG
127[ 1.426005] raid6: neonx8 gen() 2141 MB/s
128[ 1.494067] raid6: neonx8 xor() 1598 MB/s
129[ 1.562139] raid6: neonx4 gen() 2188 MB/s
130[ 1.630191] raid6: neonx4 xor() 1565 MB/s
131[ 1.698267] raid6: neonx2 gen() 2077 MB/s
132[ 1.766318] raid6: neonx2 xor() 1437 MB/s
133[ 1.834402] raid6: neonx1 gen() 1775 MB/s
134[ 1.902447] raid6: neonx1 xor() 1219 MB/s
135[ 1.970514] raid6: int64x8 gen() 1437 MB/s
136[ 2.038579] raid6: int64x8 xor() 771 MB/s
137[ 2.106656] raid6: int64x4 gen() 1602 MB/s
138[ 2.174710] raid6: int64x4 xor() 818 MB/s
139[ 2.242794] raid6: int64x2 gen() 1397 MB/s
140[ 2.310839] raid6: int64x2 xor() 750 MB/s
141[ 2.378924] raid6: int64x1 gen() 1032 MB/s
142[ 2.446989] raid6: int64x1 xor() 517 MB/s
143[ 2.447027] raid6: using algorithm neonx4 gen() 2188 MB/s
144[ 2.450981] raid6: .... xor() 1565 MB/s, rmw enabled
145[ 2.455912] raid6: using neon recovery algorithm
146[ 2.461010] iommu: Default domain type: Translated
147[ 2.465559] SCSI subsystem initialized
148[ 2.469198] usbcore: registered new interface driver usbfs
149[ 2.474538] usbcore: registered new interface driver hub
150[ 2.479815] usbcore: registered new device driver usb
151[ 2.484864] mc: Linux media interface: v0.10
152[ 2.489058] videodev: Linux video capture interface: v2.00
153[ 2.494532] EDAC MC: Ver: 3.0.0
154[ 2.497972] zynqmp-ipi-mbox mailbox@ff990400: Registered ZynqMP IPI mbox with TX/RX channels.
155[ 2.506276] FPGA manager framework
156[ 2.509582] Advanced Linux Sound Architecture Driver Initialized.
157[ 2.515799] Bluetooth: Core ver 2.22
158[ 2.519069] NET: Registered protocol family 31
159[ 2.523470] Bluetooth: HCI device and connection manager initialized
160[ 2.529786] Bluetooth: HCI socket layer initialized
161[ 2.534628] Bluetooth: L2CAP socket layer initialized
162[ 2.539652] Bluetooth: SCO socket layer initialized
163[ 2.544746] clocksource: Switched to clocksource arch_sys_counter
164[ 2.550675] VFS: Disk quotas dquot_6.6.0
165[ 2.554479] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
166[ 2.565621] NET: Registered protocol family 2
167[ 2.566000] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
168[ 2.574116] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
169[ 2.582145] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
170[ 2.589591] TCP: Hash tables configured (established 32768 bind 32768)
171[ 2.595773] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
172[ 2.602430] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
173[ 2.609607] NET: Registered protocol family 1
174[ 2.614068] RPC: Registered named UNIX socket transport module.
175[ 2.619666] RPC: Registered udp transport module.
176[ 2.624330] RPC: Registered tcp transport module.
177[ 2.629005] RPC: Registered tcp NFSv4.1 backchannel transport module.
178[ 2.635994] PCI: CLS 0 bytes, default 64
179[ 2.664946] Initialise system trusted keyrings
180[ 2.665073] workingset: timestamp_bits=46 max_order=20 bucket_order=0
181[ 2.670835] NFS: Registering the id_resolver key type
182[ 2.675186] Key type id_resolver registered
183[ 2.679324] Key type id_legacy registered
184[ 2.683326] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
185[ 2.689981] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
186[ 2.733160] NET: Registered protocol family 38
187[ 2.733203] xor: measuring software checksum speed
188[ 2.740898] 8regs : 2363 MB/sec
189[ 2.744558] 32regs : 2799 MB/sec
190[ 2.749509] arm64_neon : 2380 MB/sec
191[ 2.749695] xor: using function: 32regs (2799 MB/sec)
192[ 2.754718] Key type asymmetric registered
193[ 2.758783] Asymmetric key parser 'x509' registered
194[ 2.763646] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
195[ 2.770981] io scheduler mq-deadline registered
196[ 2.775477] io scheduler kyber registered
197[ 2.781411] ps_pcie_dma init()
198[ 2.808249] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
199[ 2.810098] Serial: AMBA driver
200[ 2.814639] cacheinfo: Unable to detect cache hierarchy for CPU 0
201[ 2.822673] brd: module loaded
202[ 2.827065] loop: module loaded
203[ 2.827968] mtdoops: mtd device (mtddev=name/number) must be supplied
204[ 2.832463] libphy: Fixed MDIO Bus: probed
205[ 2.836318] tun: Universal TUN/TAP device driver, 1.6
206[ 2.840147] CAN device driver interface
207[ 2.844653] usbcore: registered new interface driver asix
208[ 2.849263] usbcore: registered new interface driver ax88179_178a
209[ 2.855304] usbcore: registered new interface driver cdc_ether
210[ 2.861101] usbcore: registered new interface driver net1080
211[ 2.866719] usbcore: registered new interface driver cdc_subset
212[ 2.872605] usbcore: registered new interface driver zaurus
213[ 2.878148] usbcore: registered new interface driver cdc_ncm
214[ 2.884680] usbcore: registered new interface driver uas
215[ 2.889052] usbcore: registered new interface driver usb-storage
216[ 2.895616] rtc_zynqmp ffa60000.rtc: registered as rtc0
217[ 2.900196] rtc_zynqmp ffa60000.rtc: setting system clock to 2021-08-04T07:14:51 UTC (1628061291)
218[ 2.909051] i2c /dev entries driver
219[ 2.914158] usbcore: registered new interface driver uvcvideo
220[ 2.918170] USB Video Class driver (1.1.1)
221[ 2.923251] Bluetooth: HCI UART driver ver 2.3
222[ 2.926658] Bluetooth: HCI UART protocol H4 registered
223[ 2.931752] Bluetooth: HCI UART protocol BCSP registered
224[ 2.937040] Bluetooth: HCI UART protocol LL registered
225[ 2.942130] Bluetooth: HCI UART protocol ATH3K registered
226[ 2.947503] Bluetooth: HCI UART protocol Three-wire (H5) registered
227[ 2.953758] Bluetooth: HCI UART protocol Intel registered
228[ 2.959096] Bluetooth: HCI UART protocol QCA registered
229[ 2.964296] usbcore: registered new interface driver bcm203x
230[ 2.969917] usbcore: registered new interface driver bpa10x
231[ 2.975457] usbcore: registered new interface driver bfusb
232[ 2.980905] usbcore: registered new interface driver btusb
233[ 2.986364] usbcore: registered new interface driver ath3k
234[ 2.991855] EDAC MC: ECC not enabled
235[ 2.995480] EDAC DEVICE0: Giving out device to module zynqmp-ocm-edac controller zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT)
236[ 3.007855] sdhci: Secure Digital Host Controller Interface driver
237[ 3.013589] sdhci: Copyright(c) Pierre Ossman
238[ 3.017905] sdhci-pltfm: SDHCI platform and OF driver helper
239[ 3.023912] ledtrig-cpu: registered to indicate activity on CPUs
240[ 3.029506] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
241[ 3.035932] zynqmp_firmware_probe Platform Management API v1.1
242[ 3.041693] zynqmp_firmware_probe Trustzone version v1.0
243[ 3.075549] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: zynqmp pinctrl initialized
244[ 3.119898] alg: No test for xilinx-zynqmp-aes (zynqmp-aes)
245[ 3.119971] zynqmp_aes firmware:zynqmp-firmware:zynqmp-aes: AES Successfully Registered
246[ 3.127987] alg: No test for xilinx-keccak-384 (zynqmp-keccak-384)
247[ 3.134127] alg: No test for xilinx-zynqmp-rsa (zynqmp-rsa)
248[ 3.139627] usbcore: registered new interface driver usbhid
249[ 3.145008] usbhid: USB HID core driver
250[ 3.151591] ARM CCI_400_r1 PMU driver probed
251[ 3.152062] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered
252[ 3.159917] usbcore: registered new interface driver snd-usb-audio
253[ 3.166492] pktgen: Packet Generator for packet performance testing. Version: 2.75
254[ 3.173732] Initializing XFRM netlink socket
255[ 3.177426] NET: Registered protocol family 10
256[ 3.182174] Segment Routing with IPv6
257[ 3.185574] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
258[ 3.191622] NET: Registered protocol family 17
259[ 3.195709] NET: Registered protocol family 15
260[ 3.200116] can: controller area network core
261[ 3.204457] NET: Registered protocol family 29
262[ 3.208849] can: raw protocol
263[ 3.211779] can: broadcast manager protocol
264[ 3.215940] can: netlink gateway - max_hops=1
265[ 3.220332] Bluetooth: RFCOMM TTY layer initialized
266[ 3.225115] Bluetooth: RFCOMM socket layer initialized
267[ 3.230221] Bluetooth: RFCOMM ver 1.11
268[ 3.233932] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
269[ 3.239205] Bluetooth: BNEP filters: protocol multicast
270[ 3.244395] Bluetooth: BNEP socket layer initialized
271[ 3.249324] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
272[ 3.255209] Bluetooth: HIDP socket layer initialized
273[ 3.260262] 9pnet: Installing 9P2000 support
274[ 3.264394] Key type dns_resolver registered
275[ 3.268819] registered taskstats version 1
276[ 3.272674] Loading compiled-in X.509 certificates
277[ 3.278371] Btrfs loaded, crc32c=crc32c-generic
278[ 3.290749] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 51, base_baud = 6249999) is a xuartps
279[ 3.299775] printk: console [ttyPS0] enabled
280[ 3.299775] printk: console [ttyPS0] enabled
281[ 3.304070] printk: bootconsole [cdns0] disabled
282[ 3.304070] printk: bootconsole [cdns0] disabled
283[ 3.313706] ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 52, base_baud = 6249999) is a xuartps
284[ 3.326912] of-fpga-region fpga-full: FPGA Region probed
285[ 3.333931] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success
286[ 3.341110] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success
287[ 3.348277] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success
288[ 3.355453] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success
289[ 3.362626] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success
290[ 3.369797] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success
291[ 3.376963] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success
292[ 3.384140] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success
293[ 3.391382] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success
294[ 3.398575] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success
295[ 3.405751] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success
296[ 3.412923] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success
297[ 3.420096] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success
298[ 3.427267] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success
299[ 3.434441] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success
300[ 3.441612] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success
301[ 3.449027] xilinx-zynqmp-dpdma fd4c0000.dma-controller: Xilinx DPDMA engine is probed
302[ 3.457476] ahci-ceva fd0c0000.ahci: supply ahci not found, using dummy regulator
303[ 3.465021] ahci-ceva fd0c0000.ahci: supply phy not found, using dummy regulator
304[ 3.473125] spi-nor spi0.0: found n25q512a, expected m25p80
305[ 3.479279] spi-nor spi0.0: trying to lock already unlocked area
306[ 3.485284] spi-nor spi0.0: n25q512a (131072 Kbytes)
307[ 3.490269] 3 fixed-partitions partitions found on MTD device spi0.0
308[ 3.496612] Creating 3 MTD partitions on "spi0.0":
309[ 3.501397] 0x000000000000-0x000001e00000 : "boot"
310[ 3.506982] 0x000001e00000-0x000001e40000 : "bootenv"
311[ 3.512784] 0x000001e40000-0x000004240000 : "kernel"
312[ 3.520859] macb ff0e0000.ethernet: Not enabling partial store and forward
313[ 3.528385] libphy: MACB_mii_bus: probed
314[ 3.533023] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 39 (00:0a:35:00:22:01)
315[ 3.543235] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM
316[ 3.549818] xilinx-axipmon fd0b0000.perf-monitor: Probed Xilinx APM
317[ 3.556344] xilinx-axipmon fd490000.perf-monitor: Probed Xilinx APM
318[ 3.562895] xilinx-axipmon ffa10000.perf-monitor: Probed Xilinx APM
319[ 3.586437] pca953x 0-0020: supply vcc not found, using dummy regulator
320[ 3.593124] pca953x 0-0020: using no AI
321[ 3.597656] pca953x 0-0021: supply vcc not found, using dummy regulator
322[ 3.604327] pca953x 0-0021: using no AI
323[ 3.617729] i2c i2c-0: Added multiplexed i2c bus 2
324[ 3.629258] i2c i2c-0: Added multiplexed i2c bus 3
325[ 3.645726] random: fast init done
326[ 3.687695] i2c i2c-0: Added multiplexed i2c bus 4
327[ 3.692606] i2c i2c-0: Added multiplexed i2c bus 5
328[ 3.697397] pca954x 0-0075: registered 4 multiplexed busses for I2C mux pca9544
329[ 3.704728] cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 41
330[ 3.712380] at24 6-0054: supply vcc not found, using dummy regulator
331[ 3.719271] at24 6-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
332[ 3.726002] i2c i2c-1: Added multiplexed i2c bus 6
333[ 3.732212] si5341 7-0036: Chip: 5341 Grade: 1 Rev: 1
334[ 3.769571] i2c i2c-1: Added multiplexed i2c bus 7
335[ 3.777194] si570 8-005d: registered, current frequency 300000000 Hz
336[ 3.783576] i2c i2c-1: Added multiplexed i2c bus 8
337[ 3.803313] si570 9-005d: registered, current frequency 148500000 Hz
338[ 3.809695] i2c i2c-1: Added multiplexed i2c bus 9
339[ 3.814722] si5324 10-0069: si5328 probed
340[ 3.881060] si5324 10-0069: si5328 probe successful
341[ 3.885965] i2c i2c-1: Added multiplexed i2c bus 10
342[ 3.890960] i2c i2c-1: Added multiplexed i2c bus 11
343[ 3.895960] i2c i2c-1: Added multiplexed i2c bus 12
344[ 3.900957] i2c i2c-1: Added multiplexed i2c bus 13
345[ 3.905838] pca954x 1-0074: registered 8 multiplexed busses for I2C switch pca9548
346[ 3.913825] i2c i2c-1: Added multiplexed i2c bus 14
347[ 3.918829] i2c i2c-1: Added multiplexed i2c bus 15
348[ 3.923841] i2c i2c-1: Added multiplexed i2c bus 16
349[ 3.928851] i2c i2c-1: Added multiplexed i2c bus 17
350[ 3.933858] i2c i2c-1: Added multiplexed i2c bus 18
351[ 3.938863] i2c i2c-1: Added multiplexed i2c bus 19
352[ 3.943873] i2c i2c-1: Added multiplexed i2c bus 20
353[ 3.948959] i2c i2c-1: Added multiplexed i2c bus 21
354[ 3.953837] pca954x 1-0075: registered 8 multiplexed busses for I2C switch pca9548
355[ 3.961429] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 42
356[ 3.971494] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer with timeout 60s
357[ 3.978990] cdns-wdt ff150000.watchdog: Xilinx Watchdog Timer with timeout 10s
358[ 3.989746] zynqmp-display fd4a0000.display: vtc bridge property not present
359[ 3.998619] xilinx-dp-snd-codec fd4a0000.display:zynqmp_dp_snd_codec0: Xilinx DisplayPort Sound Codec probed
360[ 4.008785] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm0: Xilinx DisplayPort Sound PCM probed
361[ 4.016921] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm1: Xilinx DisplayPort Sound PCM probed
362[ 4.020763] mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit
363[ 4.025489] xilinx-dp-snd-card fd4a0000.display:zynqmp_dp_snd_card: ASoC: no DMI vendor name!
364[ 4.041268] xilinx-dp-snd-card fd4a0000.display:zynqmp_dp_snd_card: Xilinx DisplayPort Sound Card probed
365[ 4.050867] OF: graph: no port node found in /axi/display@fd4a0000
366[ 4.057375] xlnx-drm xlnx-drm.0: bound fd4a0000.display (ops 0xffff800010e7b8e0)
367[ 4.097796] mmc0: new high speed SDHC card at address 59b4
368[ 4.103646] mmcblk0: mmc0:59b4 SD 14.7 GiB (ro)
369[ 4.109591] mmcblk0: p1 p2
370[ 5.144773] zynqmp-display fd4a0000.display: [drm] Cannot find any crtc or sizes
371[ 5.152416] [drm] Initialized xlnx 1.0.0 20130509 for fd4a0000.display on minor 0
372[ 5.159914] zynqmp-display fd4a0000.display: ZynqMP DisplayPort Subsystem driver probed
373[ 5.168299] ahci-ceva fd0c0000.ahci: supply ahci not found, using dummy regulator
374[ 5.175846] ahci-ceva fd0c0000.ahci: supply phy not found, using dummy regulator
375[ 5.183305] ahci-ceva fd0c0000.ahci: supply target not found, using dummy regulator
376[ 5.201205] ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode
377[ 5.210165] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
378[ 5.220548] scsi host0: ahci-ceva
379[ 5.224160] scsi host1: ahci-ceva
380[ 5.227599] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 49
381[ 5.235514] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 49
382[ 5.244077] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
383[ 5.249575] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
384[ 5.257321] xhci-hcd xhci-hcd.1.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x0000000002010810
385[ 5.266736] xhci-hcd xhci-hcd.1.auto: irq 90, io mem 0xfe200000
386[ 5.272880] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
387[ 5.281139] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
388[ 5.288359] usb usb1: Product: xHCI Host Controller
389[ 5.293238] usb usb1: Manufacturer: Linux 5.10.0-xilinx-v2021.1 xhci-hcd
390[ 5.299934] usb usb1: SerialNumber: xhci-hcd.1.auto
391[ 5.305103] hub 1-0:1.0: USB hub found
392[ 5.308873] hub 1-0:1.0: 1 port detected
393[ 5.312982] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
394[ 5.318466] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
395[ 5.326124] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
396[ 5.332762] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
397[ 5.341019] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
398[ 5.348230] usb usb2: Product: xHCI Host Controller
399[ 5.353099] usb usb2: Manufacturer: Linux 5.10.0-xilinx-v2021.1 xhci-hcd
400[ 5.359790] usb usb2: SerialNumber: xhci-hcd.1.auto
401[ 5.364913] hub 2-0:1.0: USB hub found
402[ 5.368665] hub 2-0:1.0: 1 port detected
403[ 5.375631] input: gpio-keys as /devices/platform/gpio-keys/input/input0
404[ 5.382701] of_cfs_init
405[ 5.385171] of_cfs_init: OK
406[ 5.388091] cfg80211: Loading compiled-in X.509 certificates for regulatory database
407[ 5.522902] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
408[ 5.529435] clk: Not disabling unused clocks
409[ 5.533943] ALSA device list:
410[ 5.536910] #0: DisplayPort monitor
411[ 5.540846] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
412[ 5.549456] cfg80211: failed to load regulatory.db
413[ 5.554535] ata2: SATA link down (SStatus 0 SControl 330)
414[ 5.559959] ata1: SATA link down (SStatus 0 SControl 330)
415[ 5.565570] VFS: Cannot open root device "mmcblk0p2" or unknown-block(179,2): error -30
416[ 5.573574] Please append a correct "root=" boot option; here are the available partitions:
417[ 5.581918] 0100 65536 ram0
418[ 5.581920] (driver?)
419[ 5.588013] 0101 65536 ram1
420[ 5.588014] (driver?)
421[ 5.594112] 0102 65536 ram2
422[ 5.594114] (driver?)
423[ 5.600208] 0103 65536 ram3
424[ 5.600209] (driver?)
425[ 5.606297] 0104 65536 ram4
426[ 5.606299] (driver?)
427[ 5.612377] 0105 65536 ram5
428[ 5.612379] (driver?)
429[ 5.618466] 0106 65536 ram6
430[ 5.618468] (driver?)
431[ 5.624546] 0107 65536 ram7
432[ 5.624548] (driver?)
433[ 5.630645] 0108 65536 ram8
434[ 5.630647] (driver?)
435[ 5.636725] 0109 65536 ram9
436[ 5.636726] (driver?)
437[ 5.642823] 010a 65536 ram10
438[ 5.642824] (driver?)
439[ 5.648994] 010b 65536 ram11
440[ 5.648996] (driver?)
441[ 5.655161] 010c 65536 ram12
442[ 5.655163] (driver?)
443[ 5.661337] 010d 65536 ram13
444[ 5.661339] (driver?)
445[ 5.667504] 010e 65536 ram14
446[ 5.667505] (driver?)
447[ 5.673689] 010f 65536 ram15
448[ 5.673690] (driver?)
449[ 5.679857] 1f00 30720 mtdblock0
450[ 5.679859] (driver?)
451[ 5.686379] 1f01 256 mtdblock1
452[ 5.686380] (driver?)
453[ 5.692897] 1f02 36864 mtdblock2
454[ 5.692899] (driver?)
455[ 5.699411] b300 15440896 mmcblk0
456[ 5.699414] driver: mmcblk
457[ 5.706196] b301 4194304 mmcblk0p1 49de8cb8-01
458[ 5.706198]
459[ 5.712974] b302 11245568 mmcblk0p2 49de8cb8-02
460[ 5.712976]
461[ 5.719749] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,2)
462[ 5.728178] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 5.10.0-xilinx-v2021.1 #1
463[ 5.735387] Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
464[ 5.740335] Call trace:
465[ 5.742773] dump_backtrace+0x0/0x190
466[ 5.746423] show_stack+0x18/0x30
467[ 5.749731] dump_stack+0xd4/0x110
468[ 5.753123] panic+0x15c/0x324
469[ 5.756161] mount_block_root+0x1c4/0x254
470[ 5.760162] mount_root+0x10c/0x140
471[ 5.763634] prepare_namespace+0x130/0x170
472[ 5.767714] kernel_init_freeable+0x230/0x264
473[ 5.772054] kernel_init+0x14/0x114
474[ 5.775526] ret_from_fork+0x10/0x3c
475[ 5.779087] SMP: stopping secondary CPUs
476[ 5.783001] Kernel Offset: disabled
477[ 5.786479] CPU features: 0x0040002,20002004
478[ 5.790731] Memory Limit: none
479[ 5.793774] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,2) ]---