· 6 years ago · Nov 05, 2019, 10:22 AM
1U-Boot SPL 2019.04 (Oct 22 2019 - 15:56:47 +0000)
2Initialzing DDR using fixed setting
3Configuring DDR for 1600 MT/s data rate
4Trying to boot from MMC1
5
6
7U-Boot 2019.04 (Oct 22 2019 - 15:56:47 +0000)
8
9SoC: unknown (0x87920410)
10Clock Configuration:
11 CPU0(A53):1600 MHz CPU1(A53):1600 MHz CPU2(A53):1600 MHz
12 CPU3(A53):1600 MHz
13 Bus: 400 MHz DDR: 1600 MT/s FMAN: 500 MHz
14Reset Configuration Word (RCW):
15 00000000: 08100010 0a000000 00000000 00000000
16 00000010: 14550002 80004012 60040000 c1002000
17 00000020: 00000000 00000000 00000000 00038800
18 00000030: 00000000 00001100 00000096 00000001
19Model: LS1043A RDB Board
20Board: LS1043ARDB, boot from SD
21CPLD: V1.4
22PCBA: V2.0
23SERDES Reference Clocks:
24SD1_CLK1 = 156.25MHZ, SD1_CLK2 = 100.00MHZ
25I2C: ready
26DRAM: 1.9 GiB (DDR4, 32-bit, CL=11, ECC off)
27Using SERDES1 Protocol: 5205 (0x1455)
28SEC0: RNG instantiated
29FSL_SDHC: 0
30PPA Firmware: Version LSDK-18.09-1-g6b60ff6
31
32MMC read: dev # 0, block # 18944, count 128 ...
33Not a microcode
34Flash: 128 MiB
35NAND: 512 MiB
36MMC: Loading Environment from MMC... OK
37EEPROM: NXID v1
38In: serial
39Out: serial
40Err: serial
41Net:
42MMC read: dev # 0, block # 18432, count 128 ...
43Fman1: Uploading microcode version 106.4.18
44FM1@TGEC1 running firmware version 2.0.B
45FM1@TGEC1: system interface XFI
46FM1@TGEC1: Aquantia AQR105 Firmware Version 2.0.b
47PCIe0: pcie@3400000 disabled
48PCIe1: pcie@3500000 Root Complex: no link
49PCIe2: pcie@3600000 Root Complex: no link
50FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3 [PRIME], FM1@DTSEC4, FM1@DTSEC5, FM1@DTSEC6, FM1@TGEC1
51Hit any key to stop autoboot: 0
52Device: FSL_SDHC
53Manufacturer ID: 3
54OEM: 5344
55Name: SL08G
56Bus Speed: 50000000
57Mode : SD High Speed (50MHz)
58Rd Block Len: 512
59SD version 3.0
60High Capacity: Yes
61Capacity: 7.4 GiB
62Bus Width: 4-bit
63Erase Group Size: 512 Bytes
6429764651 bytes read in 1264 ms (22.5 MiB/s)
65## Loading kernel from FIT Image at a0000000 ...
66 Trying 'kernel@1' kernel subimage
67 Description: ARM64 Linux kernel
68 Type: Kernel Image
69 Compression: uncompressed
70 Data Start: 0xa00000dc
71 Data Size: 24461824 Bytes = 23.3 MiB
72 Architecture: AArch64
73 OS: Linux
74 Load Address: 0x80080000
75 Entry Point: 0x80080000
76 Verifying Hash Integrity ... OK
77## Loading fdt from FIT Image at a0000000 ...
78 Trying 'fdt@1' fdt subimage
79 Description: Flattened Device Tree blob
80 Type: Flat Device Tree
81 Compression: uncompressed
82 Data Start: 0xa1754390
83 Data Size: 32127 Bytes = 31.4 KiB
84 Architecture: AArch64
85 Load Address: 0x90000000
86 Verifying Hash Integrity ... OK
87 Loading fdt from 0xa1754390 to 0x90000000
88 Booting using the fdt blob at 0x90000000
89 Loading Kernel Image ... OK
90 Using Device Tree in place at 0000000090000000, end 000000009001ad7e
91WARNING failed to get smmu node: FDT_ERR_NOTFOUND
92WARNING failed to get smmu node: FDT_ERR_NOTFOUND
93
94Starting kernel ...
95
96[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
97[ 0.000000] Linux version 4.19.79 (builder@build) (gcc version 8.3.0 (Debian 8.3.0-2)) #1 SMP PREEMPT Tue Oct 22 17:55:39 UTC 2019
98[ 0.000000] Machine model: LS1043A RDB Board
99[ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0500 (options '')
100[ 0.000000] bootconsole [uart8250] enabled
101[ 0.000000] efi: Getting EFI parameters from FDT:
102[ 0.000000] efi: UEFI not found.
103[ 0.000000] OF: reserved mem: initialized node qman-fqd, compatible id fsl,qman-fqd
104[ 0.000000] OF: reserved mem: initialized node qman-pfdr, compatible id fsl,qman-pfdr
105[ 0.000000] OF: reserved mem: initialized node bman-fbpr, compatible id fsl,bman-fbpr
106[ 0.000000] cma: Reserved 32 MiB at 0x00000000f6000000
107[ 0.000000] NUMA: No NUMA configuration found
108[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000fbdfffff]
109[ 0.000000] NUMA: NODE_DATA [mem 0xfbdc7f40-0xfbdc96ff]
110[ 0.000000] Zone ranges:
111[ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000fbdfffff]
112[ 0.000000] Normal empty
113[ 0.000000] Movable zone start for each node
114[ 0.000000] Early memory node ranges
115[ 0.000000] node 0: [mem 0x0000000080000000-0x00000000f7ffffff]
116[ 0.000000] node 0: [mem 0x00000000fb000000-0x00000000fb7fffff]
117[ 0.000000] node 0: [mem 0x00000000fbc00000-0x00000000fbdfffff]
118[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000fbdfffff]
119[ 0.000000] psci: probing for conduit method from DT.
120[ 0.000000] psci: PSCIv0.2 detected in firmware.
121[ 0.000000] psci: Using standard PSCI v0.2 function IDs
122[ 0.000000] psci: Trusted OS migration not required
123[ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x400 with crng_init=0
124[ 0.000000] percpu: Embedded 24 pages/cpu s59480 r8192 d30632 u98304
125[ 0.000000] Detected VIPT I-cache on CPU0
126[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
127[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 486152
128[ 0.000000] Policy zone: DMA32
129[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootwait rw earlycon=uart8250,0x21c0500 console=ttyS0,115200
130[ 0.000000] Memory: 1885240K/1976320K available (14524K kernel code, 1680K rwdata, 6100K rodata, 1536K init, 936K bss, 58312K reserved, 32768K cma-reserved)
131[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
132[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
133[ 0.000000] Tasks RCU enabled.
134[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
135[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
136[ 0.000000] GIC: Using split EOI/Deactivate mode
137[ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858
138[ 0.000000] arch_timer: CPU0: Trapping CNTVCT access
139[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
140[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
141[ 0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
142[ 0.008500] Console: colour dummy device 80x25
143[ 0.013004] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
144[ 0.023411] pid_max: default: 32768 minimum: 301
145[ 0.028116] Security Framework initialized
146[ 0.032781] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
147[ 0.040223] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
148[ 0.047331] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
149[ 0.054076] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
150[ 0.085297] ASID allocator initialised with 32768 entries
151[ 0.098737] rcu: Hierarchical SRCU implementation.
152[ 0.112802] EFI services will not be available.
153[ 0.125368] smp: Bringing up secondary CPUs ...
154[ 0.162030] Detected VIPT I-cache on CPU1
155[ 0.162056] arch_timer: CPU1: Trapping CNTVCT access
156[ 0.162061] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
157[ 0.194061] Detected VIPT I-cache on CPU2
158[ 0.194075] arch_timer: CPU2: Trapping CNTVCT access
159[ 0.194079] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
160[ 0.226101] Detected VIPT I-cache on CPU3
161[ 0.226115] arch_timer: CPU3: Trapping CNTVCT access
162[ 0.226118] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
163[ 0.226157] smp: Brought up 1 node, 4 CPUs
164[ 0.276974] SMP: Total of 4 processors activated.
165[ 0.281701] CPU features: detected: 32-bit EL0 Support
166[ 0.287165] CPU: All CPU(s) started at EL2
167[ 0.291288] alternatives: patching kernel code
168[ 0.296688] devtmpfs: initialized
169[ 0.303800] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
170[ 0.313610] futex hash table entries: 1024 (order: 4, 65536 bytes)
171[ 0.320569] xor: measuring software checksum speed
172[ 0.364063] 8regs : 3166.000 MB/sec
173[ 0.408091] 8regs_prefetch: 2735.000 MB/sec
174[ 0.452120] 32regs : 3632.000 MB/sec
175[ 0.496149] 32regs_prefetch: 3078.000 MB/sec
176[ 0.500787] xor: using function: 32regs (3632.000 MB/sec)
177[ 0.506213] pinctrl core: initialized pinctrl subsystem
178[ 0.512170] DMI not present or invalid.
179[ 0.516236] NET: Registered protocol family 16
180[ 0.520933] audit: initializing netlink subsys (disabled)
181[ 0.526456] audit: type=2000 audit(0.480:1): state=initialized audit_enabled=0 res=1
182[ 0.534246] cpuidle: using governor menu
183[ 0.538287] Bman ver:0a02,02,01
184[ 0.542847] qman-fqd addr 0x00000000fb800000 size 0x400000
185[ 0.548359] qman-pfdr addr 0x00000000f8000000 size 0x2000000
186[ 0.554047] Qman ver:0a01,03,02,00
187[ 0.557596] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
188[ 0.565031] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
189[ 0.572627] DMA: preallocated 256 KiB pool for atomic allocations
190[ 0.579347] Serial: AMBA PL011 UART driver
191[ 0.584687] Machine: LS1043A RDB Board
192[ 0.588454] SoC family: QorIQ LS1043A
193[ 0.592126] SoC ID: svr:0x87920410, Revision: 1.0
194[ 0.616493] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
195[ 0.623501] cryptd: max_cpu_qlen set to 1000
196[ 0.692401] raid6: int64x1 gen() 635 MB/s
197[ 0.764759] raid6: int64x1 xor() 609 MB/s
198[ 0.837164] raid6: int64x2 gen() 956 MB/s
199[ 0.909543] raid6: int64x2 xor() 812 MB/s
200[ 0.981584] raid6: int64x4 gen() 1368 MB/s
201[ 1.053627] raid6: int64x4 xor() 998 MB/s
202[ 1.125653] raid6: int64x8 gen() 1586 MB/s
203[ 1.197701] raid6: int64x8 xor() 1022 MB/s
204[ 1.269797] raid6: neonx1 gen() 1022 MB/s
205[ 1.341798] raid6: neonx1 xor() 1197 MB/s
206[ 1.413849] raid6: neonx2 gen() 1591 MB/s
207[ 1.485892] raid6: neonx2 xor() 1604 MB/s
208[ 1.557947] raid6: neonx4 gen() 2077 MB/s
209[ 1.629983] raid6: neonx4 xor() 1945 MB/s
210[ 1.702035] raid6: neonx8 gen() 2165 MB/s
211[ 1.774088] raid6: neonx8 xor() 1998 MB/s
212[ 1.778376] raid6: using algorithm neonx8 gen() 2165 MB/s
213[ 1.783799] raid6: .... xor() 1998 MB/s, rmw enabled
214[ 1.788784] raid6: using neon recovery algorithm
215[ 1.793826] ACPI: Interpreter disabled.
216[ 1.799843] vgaarb: loaded
217[ 1.802702] SCSI subsystem initialized
218[ 1.806672] usbcore: registered new interface driver usbfs
219[ 1.812210] usbcore: registered new interface driver hub
220[ 1.817584] usbcore: registered new device driver usb
221[ 1.823409] i2c i2c-0: using dma0chan16 (tx) and dma0chan17 (rx) for DMA transfers
222[ 1.831019] i2c i2c-0: IMX I2C adapter registered
223[ 1.836513] pps_core: LinuxPPS API ver. 1 registered
224[ 1.841502] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
225[ 1.850688] PTP clock support registered
226[ 1.854744] EDAC MC: Ver: 3.0.0
227[ 1.858068] bman-fbpr addr 0x00000000fa000000 size 0x1000000
228[ 1.863786] Bman err interrupt handler present
229[ 1.868691] Bman portal initialised, cpu 0
230[ 1.872887] Bman portal initialised, cpu 1
231[ 1.877070] Bman portal initialised, cpu 2
232[ 1.881254] Bman portal initialised, cpu 3
233[ 1.885368] Bman portals initialised
234[ 1.889834] Qman err interrupt handler present
235[ 1.894475] QMan: Allocated lookup table at (____ptrval____), entry count 65537
236[ 1.902227] Qman portal initialised, cpu 0
237[ 1.906405] Qman portal initialised, cpu 1
238[ 1.910579] Qman portal initialised, cpu 2
239[ 1.914755] Qman portal initialised, cpu 3
240[ 1.918869] Qman portals initialised
241[ 1.922523] Bman: BPID allocator includes range 32:32
242[ 1.927646] Qman: FQID allocator includes range 256:256
243[ 1.932896] Qman: FQID allocator includes range 32768:32768
244[ 1.938542] Qman: CGRID allocator includes range 0:256
245[ 1.943839] Qman: pool channel allocator includes range 1025:15
246[ 1.949865] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree
247[ 1.956151] fsl-ifc 1530000.ifc: Freescale Integrated Flash Controller
248[ 1.962723] fsl-ifc 1530000.ifc: IFC version 1.4, 8 banks
249[ 1.968334] Advanced Linux Sound Architecture Driver Initialized.
250[ 1.974912] clocksource: Switched to clocksource arch_sys_counter
251[ 1.981133] VFS: Disk quotas dquot_6.6.0
252[ 1.985108] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
253[ 1.992088] pnp: PnP ACPI: disabled
254[ 1.999798] NET: Registered protocol family 2
255[ 2.004476] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes)
256[ 2.012398] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
257[ 2.019762] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
258[ 2.026594] TCP: Hash tables configured (established 16384 bind 16384)
259[ 2.033222] UDP hash table entries: 1024 (order: 3, 32768 bytes)
260[ 2.039293] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
261[ 2.045865] NET: Registered protocol family 1
262[ 2.050453] RPC: Registered named UNIX socket transport module.
263[ 2.056407] RPC: Registered udp transport module.
264[ 2.061133] RPC: Registered tcp transport module.
265[ 2.065859] RPC: Registered tcp NFSv4.1 backchannel transport module.
266[ 2.072847] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
267[ 2.080985] kvm [1]: 8-bit VMID
268[ 2.084583] kvm [1]: vgic interrupt IRQ1
269[ 2.088592] kvm [1]: Hyp mode initialized successfully
270[ 2.095626] Initialise system trusted keyrings
271[ 2.100154] workingset: timestamp_bits=44 max_order=19 bucket_order=0
272[ 2.107132] NFS: Registering the id_resolver key type
273[ 2.112217] Key type id_resolver registered
274[ 2.116419] Key type id_legacy registered
275[ 2.120451] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
276[ 2.127252] fuse init (API version 7.27)
277[ 2.131266] 9p: Installing v9fs 9p2000 file system support
278[ 2.138550] Key type asymmetric registered
279[ 2.142667] Asymmetric key parser 'x509' registered
280[ 2.147591] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
281[ 2.155089] io scheduler noop registered
282[ 2.159031] io scheduler deadline registered
283[ 2.163345] io scheduler cfq registered (default)
284[ 2.168072] io scheduler mq-deadline registered
285[ 2.172624] io scheduler kyber registered
286[ 2.185580] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges:
287[ 2.192943] layerscape-pcie 3500000.pcie: IO 0x4800010000..0x480001ffff -> 0x00000000
288[ 2.201085] layerscape-pcie 3500000.pcie: MEM 0x4840000000..0x487fffffff -> 0x40000000
289[ 2.209320] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0000:00
290[ 2.216062] pci_bus 0000:00: root bus resource [bus 00-ff]
291[ 2.221577] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
292[ 2.227791] pci_bus 0000:00: root bus resource [mem 0x4840000000-0x487fffffff] (bus address [0x40000000-0x7fffffff])
293[ 2.241083] pci 0000:00:00.0: BAR 6: assigned [mem 0x4840000000-0x48400007ff pref]
294[ 2.248698] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
295[ 2.254100] pcieport 0000:00:00.0: Signaling PME with IRQ 58
296[ 2.259859] pcieport 0000:00:00.0: AER enabled with IRQ 59
297[ 2.265463] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges:
298[ 2.272821] layerscape-pcie 3600000.pcie: IO 0x5000010000..0x500001ffff -> 0x00000000
299[ 2.280960] layerscape-pcie 3600000.pcie: MEM 0x5040000000..0x507fffffff -> 0x40000000
300[ 2.289174] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0001:00
301[ 2.295913] pci_bus 0001:00: root bus resource [bus 00-ff]
302[ 2.301429] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
303[ 2.310438] pci_bus 0001:00: root bus resource [mem 0x5040000000-0x507fffffff] (bus address [0x40000000-0x7fffffff])
304[ 2.323644] pci 0001:00:00.0: BAR 6: assigned [mem 0x5040000000-0x50400007ff pref]
305[ 2.331257] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
306[ 2.336628] pcieport 0001:00:00.0: Signaling PME with IRQ 60
307[ 2.342381] pcieport 0001:00:00.0: AER enabled with IRQ 61
308[ 2.349305] EINJ: ACPI disabled.
309[ 2.357188] Freescale LS2 console driver
310[ 2.361208] fsl-ls2-console: device fsl_mc_console registered
311[ 2.367032] fsl-ls2-console: device fsl_aiop_console registered
312[ 2.377702] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
313[ 2.385437] console [ttyS0] disabled
314[ 2.389059] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 38, base_baud = 25000000) is a 16550A
315[ 2.397912] console [ttyS0] enabled
316[ 2.397912] console [ttyS0] enabled
317[ 2.404894] bootconsole [uart8250] disabled
318[ 2.404894] bootconsole [uart8250] disabled
319[ 2.413531] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 38, base_baud = 25000000) is a 16550A
320[ 2.422562] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 39, base_baud = 25000000) is a 16550A
321[ 2.431593] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 39, base_baud = 25000000) is a 16550A
322[ 2.440933] SuperH (H)SCI(F) driver initialized
323[ 2.445994] msm_serial: driver initialized
324[ 2.456971] brd: module loaded
325[ 2.464100] loop: module loaded
326[ 2.468158] at24 0-0052: 65536 byte 24c512 EEPROM, writable, 1 bytes/write
327[ 2.475836] at24 0-0053: 65536 byte 24c512 EEPROM, writable, 1 bytes/write
328[ 2.484338] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
329[ 2.493306] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
330[ 2.503557] scsi host0: ahci-qoriq
331[ 2.507115] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 49
332[ 2.515738] 60000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x00227e
333[ 2.525737] Amd/Fujitsu Extended Query Table at 0x0040
334[ 2.530879] Amd/Fujitsu Extended Query version 1.3.
335[ 2.535926] number of CFI chips: 1
336[ 2.540739] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xac
337[ 2.547091] nand: Micron MT29F4G08ABBDAH4
338[ 2.551098] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
339[ 2.558936] Bad block table found at page 262080, version 0x01
340[ 2.565243] Bad block table found at page 262016, version 0x01
341[ 2.571841] fsl,ifc-nand 7e800000.nand: IFC NAND device at 0x7e800000, bank 1
342[ 2.580868] m25p80 spi0.0: n25q128a13 (16384 Kbytes)
343[ 2.588196] libphy: Fixed MDIO Bus: probed
344[ 2.592732] tun: Universal TUN/TAP device driver, 1.6
345[ 2.598610] thunder_xcv, ver 1.0
346[ 2.601858] thunder_bgx, ver 1.0
347[ 2.605104] nicpf, ver 1.0
348[ 2.607990] libphy: Freescale XGMAC MDIO Bus: probed
349[ 2.614716] libphy: Freescale XGMAC MDIO Bus: probed
350[ 2.621307] libphy: Freescale XGMAC MDIO Bus: probed
351[ 2.626499] libphy: Freescale XGMAC MDIO Bus: probed
352[ 2.631686] libphy: Freescale XGMAC MDIO Bus: probed
353[ 2.636875] libphy: Freescale XGMAC MDIO Bus: probed
354[ 2.642085] libphy: Freescale XGMAC MDIO Bus: probed
355[ 2.647282] libphy: Freescale XGMAC MDIO Bus: probed
356[ 2.652477] libphy: Freescale XGMAC MDIO Bus: probed
357[ 2.669303] Freescale FM module, FMD API version 21.1.0
358[ 2.677234] Freescale FM Ports module
359[ 2.680897] fsl_mac: fsl_mac: FSL FMan MAC API based driver
360[ 2.686918] fsl_mac 1ae0000.ethernet: FMan MEMAC
361[ 2.691538] fsl_mac 1ae0000.ethernet: FMan MAC address: 00:04:9f:03:da:01
362[ 2.698664] fsl_mac 1ae2000.ethernet: FMan MEMAC
363[ 2.703284] fsl_mac 1ae2000.ethernet: FMan MAC address: 00:04:9f:03:da:02
364[ 2.710162] fsl_mac 1ae4000.ethernet: FMan MEMAC
365[ 2.714781] fsl_mac 1ae4000.ethernet: FMan MAC address: 00:1f:7b:63:35:e9
366[ 2.721660] fsl_mac 1ae6000.ethernet: FMan MEMAC
367[ 2.726277] fsl_mac 1ae6000.ethernet: FMan MAC address: 00:04:9f:03:da:04
368[ 2.733404] fsl_mac 1ae8000.ethernet: FMan MEMAC
369[ 2.738021] fsl_mac 1ae8000.ethernet: FMan MAC address: 00:04:9f:03:da:05
370[ 2.745150] fsl_mac 1aea000.ethernet: FMan MEMAC
371[ 2.749765] fsl_mac 1aea000.ethernet: FMan MAC address: 00:04:9f:03:da:06
372[ 2.756645] fsl_mac 1af0000.ethernet: FMan MEMAC
373[ 2.761262] fsl_mac 1af0000.ethernet: FMan MAC address: 00:04:9f:03:da:07
374[ 2.768077] fsl_dpa: FSL DPAA Ethernet driver
375[ 2.773318] fsl_dpa soc:fsl,dpaa:ethernet@0: Skip RX PCD High Priority FQs initialization
376[ 2.784477] fsl_dpa: fsl_dpa: Probed interface eth0
377[ 2.789832] fsl_dpa soc:fsl,dpaa:ethernet@1: Skip RX PCD High Priority FQs initialization
378[ 2.801106] fsl_dpa: fsl_dpa: Probed interface eth1
379[ 2.806563] fsl_dpa soc:fsl,dpaa:ethernet@2: Skip RX PCD High Priority FQs initialization
380[ 2.818029] fsl_dpa: fsl_dpa: Probed interface eth2
381[ 2.823605] fsl_dpa soc:fsl,dpaa:ethernet@3: Skip RX PCD High Priority FQs initialization
382[ 2.829128] ata1: SATA link down (SStatus 0 SControl 300)
383[ 2.835301] fsl_dpa: fsl_dpa: Probed interface eth3
384[ 2.842841] fsl_dpa soc:fsl,dpaa:ethernet@4: Skip RX PCD High Priority FQs initialization
385[ 2.854726] fsl_dpa: fsl_dpa: Probed interface eth4
386[ 2.860506] fsl_dpa soc:fsl,dpaa:ethernet@5: Skip RX PCD High Priority FQs initialization
387[ 2.872611] fsl_dpa: fsl_dpa: Probed interface eth5
388[ 2.878502] fsl_dpa soc:fsl,dpaa:ethernet@8: Skip RX PCD High Priority FQs initialization
389[ 2.890820] fsl_dpa: fsl_dpa: Probed interface eth6
390[ 2.895728] fsl_advanced: FSL DPAA Advanced drivers:
391[ 2.900688] fsl_proxy: FSL DPAA Proxy initialization driver
392[ 2.906443] fsl_oh: FSL FMan Offline Parsing port driver
393[ 2.912503] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
394[ 2.919546] e1000: Copyright (c) 1999-2006 Intel Corporation.
395[ 2.925310] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
396[ 2.931137] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
397[ 2.937074] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
398[ 2.944030] igb: Copyright (c) 2007-2014 Intel Corporation.
399[ 2.949620] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
400[ 2.957444] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
401[ 2.963719] sky2: driver version 1.30
402[ 2.968391] VFIO - User Level meta-driver version: 0.3
403[ 2.973833] dwc3 2f00000.usb3: Failed to get clk 'ref': -2
404[ 2.979908] dwc3 3000000.usb3: Failed to get clk 'ref': -2
405[ 2.985720] dwc3 3100000.usb3: Failed to get clk 'ref': -2
406[ 2.992537] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
407[ 2.999063] ehci-pci: EHCI PCI platform driver
408[ 3.003523] ehci-platform: EHCI generic platform driver
409[ 3.008890] ehci-orion: EHCI orion driver
410[ 3.013004] ehci-exynos: EHCI EXYNOS driver
411[ 3.017272] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
412[ 3.023461] ohci-pci: OHCI PCI platform driver
413[ 3.027920] ohci-platform: OHCI generic platform driver
414[ 3.033269] ohci-exynos: OHCI EXYNOS driver
415[ 3.037869] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
416[ 3.043362] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
417[ 3.051346] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000202010810
418[ 3.060768] xhci-hcd xhci-hcd.0.auto: irq 46, io mem 0x02f00000
419[ 3.067110] hub 1-0:1.0: USB hub found
420[ 3.070862] hub 1-0:1.0: 1 port detected
421[ 3.074954] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
422[ 3.080439] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
423[ 3.088098] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
424[ 3.094920] hub 2-0:1.0: USB hub found
425[ 3.098671] hub 2-0:1.0: 1 port detected
426[ 3.102795] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
427[ 3.108288] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
428[ 3.116266] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000202010810
429[ 3.125674] xhci-hcd xhci-hcd.1.auto: irq 47, io mem 0x03000000
430[ 3.131936] hub 3-0:1.0: USB hub found
431[ 3.135694] hub 3-0:1.0: 1 port detected
432[ 3.139757] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
433[ 3.145242] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
434[ 3.152900] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
435[ 3.159708] hub 4-0:1.0: USB hub found
436[ 3.163465] hub 4-0:1.0: 1 port detected
437[ 3.167579] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
438[ 3.173069] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 5
439[ 3.181039] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000202010810
440[ 3.190443] xhci-hcd xhci-hcd.2.auto: irq 48, io mem 0x03100000
441[ 3.196698] hub 5-0:1.0: USB hub found
442[ 3.200457] hub 5-0:1.0: 1 port detected
443[ 3.204525] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
444[ 3.210010] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 6
445[ 3.217669] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
446[ 3.224471] hub 6-0:1.0: USB hub found
447[ 3.228227] hub 6-0:1.0: 1 port detected
448[ 3.232591] usbcore: registered new interface driver usb-storage
449[ 3.243513] rtc-ds1307 0-0068: registered as rtc0
450[ 3.248689] ftm-alarm 29d0000.timer: registered as rtc1
451[ 3.254481] pcf85363 0-0051: pcf85363_rtc_read_time: error -6
452[ 3.260286] pcf85363 0-0051: registered as rtc2
453[ 3.265382] i2c /dev entries driver
454[ 3.270806] ptp_qoriq: device tree node missing required elements, try automatic configuration
455[ 3.279558] pps pps0: new PPS source ptp0
456[ 3.286035] imx2-wdt 2ad0000.wdog: timeout 60 sec (nowayout=0)
457[ 3.292916] qoriq_cpufreq: Freescale QorIQ CPU frequency scaling driver
458[ 3.299930] sdhci: Secure Digital Host Controller Interface driver
459[ 3.306106] sdhci: Copyright(c) Pierre Ossman
460[ 3.310746] Synopsys Designware Multimedia Card Interface Driver
461[ 3.317843] sdhci-pltfm: SDHCI platform and OF driver helper
462[ 3.349784] mmc0: SDHCI controller on 1560000.esdhc [1560000.esdhc] using ADMA 64-bit
463[ 3.358952] ledtrig-cpu: registered to indicate activity on CPUs
464[ 3.365604] caam 1700000.crypto: Linux CAAM Queue I/F driver initialised
465[ 3.374769] caam 1700000.crypto: device ID = 0x0a12060000000000 (Era 8)
466[ 3.381508] caam 1700000.crypto: job rings = 3, qi = 1
467[ 3.390306] caam algorithms registered in /proc/crypto
468[ 3.396094] caam 1700000.crypto: caam pkc algorithms registered in /proc/crypto
469[ 3.403775] caam_jr 1710000.jr: registering rng-caam
470[ 3.411040] caam 1700000.crypto: algorithms registered in /proc/crypto
471[ 3.418843] usbcore: registered new interface driver usbhid
472[ 3.424424] usbhid: USB HID core driver
473[ 3.426377] mmc0: new high speed SDHC card at address aaaa
474[ 3.429081] Freescale USDPAA process driver
475[ 3.434395] mmcblk0: mmc0:aaaa SL08G 7.40 GiB
476[ 3.437927] fsl-usdpaa: no region found
477[ 3.443390] mmcblk0: p1 p2
478[ 3.446195] Freescale USDPAA process IRQ driver
479[ 3.455509] optee: probing for conduit method from DT.
480[ 3.460648] optee: api uid mismatch
481[ 3.465089] u32 classifier
482[ 3.467795] Actions configured
483[ 3.471642] Initializing XFRM netlink socket
484[ 3.475966] NET: Registered protocol family 10
485[ 3.481097] Segment Routing with IPv6
486[ 3.484801] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
487[ 3.491002] NET: Registered protocol family 17
488[ 3.495453] NET: Registered protocol family 15
489[ 3.499916] Bridge firewalling registered
490[ 3.503986] 8021q: 802.1Q VLAN Support v1.8
491[ 3.508199] 9pnet: Installing 9P2000 support
492[ 3.512483] tsn generic netlink module v1 init...
493[ 3.517219] Key type dns_resolver registered
494[ 3.521844] registered taskstats version 1
495[ 3.525975] usb usb5-port1: over-current condition
496[ 3.526924] Loading compiled-in X.509 certificates
497[ 3.535881] Btrfs loaded, crc32c=crc32c-generic
498[ 3.542932] rtc-ds1307 0-0068: setting system clock to 2019-11-05 10:17:02 UTC (1572949022)
499[ 3.551309] usb usb6-port1: over-current condition
500[ 3.555154] ALSA device list:
501[ 3.559054] No soundcards found.
502[ 3.611076] random: fast init done
503[ 3.665419] EXT4-fs (mmcblk0p2): recovery complete
504[ 3.785302] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
505[ 3.793412] VFS: Mounted root (ext4 filesystem) on device 179:2.
506[ 3.807288] devtmpfs: mounted
507[ 3.810718] Freeing unused kernel memory: 1536K
508[ 3.815301] Run /sbin/init as init process
509[ 4.367518] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
510[ 4.389068] systemd[1]: Detected architecture arm64.
511
512Welcome to Mentor Embedded Linux Omni OS 2.0 (buster)!
513
514[ 4.414979] systemd[1]: No hostname configured.
515[ 4.419520] systemd[1]: Set hostname to <localhost>.
516[ 4.425667] systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument
517[ 4.432953] systemd[1]: Hardware watchdog 'imx2+ watchdog', version 0
518[ 4.439404] systemd[1]: Set hardware watchdog to 15s.
519[ 4.603837] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
520[ 4.620886] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
521[ 4.641803] systemd[1]: /lib/systemd/system/auditd.service:11: PIDFile= references path below legacy directory /var/run/, updating /var/run/auditd.pid → /run/auditd.pid; please update the unit file accordingly.
522[ 4.793471] random: systemd: uninitialized urandom read (16 bytes read)
523[ 4.802410] random: systemd: uninitialized urandom read (16 bytes read)
524[ OK ] Started Forward Password R…uests to Wall Directory Watch.
525[ 4.826985] random: systemd: uninitialized urandom read (16 bytes read)
526[ OK ] Listening on Journal Socket (/dev/log).
527[ OK ] Created slice system-serial\x2dgetty.slice.
528[ OK ] Created slice User and Session Slice.
529[ OK ] Listening on Journal Audit Socket.
530[ OK ] Listening on udev Kernel Socket.
531[ OK ] Started Dispatch Password …ts to Console Directory Watch.
532[ OK ] Reached target Paths.
533[ OK ] Reached target Local Encrypted Volumes.
534[ OK ] Listening on initctl Compatibility Named Pipe.
535[ OK ] Created slice system-getty.slice.
536[ OK ] Reached target Remote File Systems.
537[ OK ] Listening on udev Control Socket.
538[ OK ] Reached target Swap.
539[ OK ] Listening on Journal Socket.
540 Starting Journal Service...
541 Mounting POSIX Message Queue File System...
542 Starting Create list of re…odes for the current kernel...
543 Mounting Kernel Debug File System...
544 Starting udev Coldplug all Devices...
545 Mounting Huge Pages File System...
546 Starting Load Kernel Modules...
547 Starting Uncomplicated firewall...
548[ OK ] Reached target Slices.
549[ OK ] Reached target System Time Synchronized.
550 Starting Set the console keyboard layout...
551 Starting Remount Root and Kernel File Systems...
552[ OK ] Started Journal Service.
553[ 5.301569] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
554[ OK ] Mounted POSIX Message Queue File System.
555[ OK ] Started Create list of req… nodes for the current kernel.
556[ OK ] Mounted Kernel Debug File System.
557[ OK ] Mounted Huge Pages File System.
558[ OK ] Started Load Kernel Modules.
559[ OK ] Started Uncomplicated firewall.
560[ OK ] Started Remount Root and Kernel File Systems.
561 Starting Create System Users...
562 Starting Load/Save Random Seed...
563 Starting Apply Kernel Variables...
564 Mounting Kernel Configuration File System...
565 Mounting FUSE Control File System...
566 Starting Flush Journal to Persistent Storage...
567[ OK ] Started Set the console keyboard layout.
568[ OK ] Started udev Coldplug all Devices.
569[ OK ] Started Create System Users.
570[ OK ] Started Load/Save Random Seed.
571[ OK ] Started Apply Kernel Variables.
572[ OK ] Mounted Kernel Configuration File System.
573[ OK ] Mounted FUSE Control File System.
574 Starting Create Static Device Nodes in /dev...
575 Starting Helper to synchronize boot up for ifupdown...
576[ OK ] Started Create Static Device Nodes in /dev.
577[ OK ] Started Helper to synchronize boot up for ifupdown.
578[ 5.755419] systemd-journald[283]: Received request to flush runtime journal from PID 1
579 Starting udev Kernel Device Manager...
580[ OK ] Reached target Local File Systems (Pre).
581[ OK ] Reached target Local File Systems.
582 Starting Raise network interfaces...
583 Starting Set console font and keymap...
584[ OK ] Started udev Kernel Device Manager.
585[ OK ] Started Flush Journal to Persistent Storage.
586[ OK ] Started Set console font and keymap.
587 Starting Create Volatile Files and Directories...
588[ OK ] Started Raise network interfaces.
589[ OK ] Started Create Volatile Files and Directories.
590 Starting Security Auditing Service...
591[ OK ] Found device /dev/ttyS0.
592[ 6.153462] ina2xx 0-0040: power monitor ina220 (Rshunt = 1000 uOhm)
593[ 6.155067] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator
594[ 6.168767] lm90 0-004c: Linked as a consumer to regulator.0
595[ OK ] Started Security Auditing Service.
596 Starting Update UTMP about System Boot/Shutdown...
597[ OK ] Started Update UTMP about System Boot/Shutdown.
598[ OK ] Reached target System Initialization.
599[ OK ] Started Daily rotation of log files.
600[ OK ] Started Daily apt download activities.
601[ OK ] Listening on D-Bus System Message Bus Socket.
602[ OK ] Reached target Sockets.
603[ OK ] Reached target Basic System.
604[ OK ] Started Regular background program processing daemon.
605 Starting Clam AntiVirus userspace daemon...
606 Starting Tuptime service...
607[ OK ] Started Daily Cleanup of Temporary Directories.
608[ OK ] Started MEL Setup USB Monitor.
609 Starting Login Service...
610[ OK ] Started Daily apt upgrade and clean activities.
611[ OK ] Reached target Timers.
612[ OK ] Started D-Bus System Message Bus.
613 Starting WPA supplicant...
614 Starting Network Manager...
615[ OK ] Started ClamAV virus database updater.
616[ OK ] Started Clam AntiVirus userspace daemon.
617[ OK ] Started Login Service.
618[ OK ] Started WPA supplicant.
619[ OK ] Started Network Manager.
620[ OK ] Reached target Network.
621 Starting Network Time Service...
622 Starting OpenBSD Secure Shell server...
623 Starting Permit User Sessions...
624[ OK ] Started Permit User Sessions.
625[ OK ] Started Getty on tty1.
626[ OK ] Started Serial Getty on ttyS0.
627[ OK ] Reached target Login Prompts.
628 Starting Hostname Service...
629[ OK ] Started Network Time Service.
630[ OK ] Started Tuptime service.
631[ OK ] Started Hostname Service.
632 Starting Network Manager Script Dispatcher Service...
633[ OK ] Started Network Manager Script Dispatcher Service.
634[ 9.506403] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
635[ 9.583945] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
636[ 9.607801] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
637[ 9.683980] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
638[ 9.707100] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
639[ 9.784534] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
640[ 9.807710] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
641[ 9.884515] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
642[ 9.907074] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready
643[ 9.983933] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready
644[ 10.006850] IPv6: ADDRCONF(NETDEV_UP): eth5: link is not ready
645[ 10.087960] IPv6: ADDRCONF(NETDEV_UP): eth5: link is not ready
646[ 10.111003] IPv6: ADDRCONF(NETDEV_UP): eth6: link is not ready
647[ 10.118653] IPv6: ADDRCONF(NETDEV_UP): eth6: link is not ready
648 Starting Authorization Manager...
649[ OK ] Started Authorization Manager.
650[ 14.991572] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
651[ 15.194947] random: crng init done
652[ 15.198350] random: 7 urandom warning(s) missed due to ratelimiting
653
654Mentor Embedded Linux Omni OS 2.0 (based on Debian 10) localhost.localdomain ttyS0
655
656localhost login: