· 6 years ago · Oct 02, 2019, 11:16 AM
1U-Boot 2017.09-rockchip-ayufan-1065-g95f6152134 (Aug 26 2019 - 12:41:34 +0000)
2
3Model: Pine64 RockPro64
4DRAM: 2 GiB
5DCDC_REG1@vdd_center: ; enabling
6DCDC_REG2@vdd_cpu_l: ; enabling
7DCDC_REG3@vcc_ddr: ; enabling (ret: -38)
8DCDC_REG4@vcc_1v8: set 1800000 uV; enabling
9LDO_REG1@vcc1v8_dvp: set 1800000 uV; enabling
10LDO_REG2@vcc3v0_touch: set 3000000 uV; enabling
11LDO_REG3@vcc1v8_pmu: set 1800000 uV; enabling
12LDO_REG4@vcc_sd: set 3300000 uV; enabling
13LDO_REG5@vcca3v0_codec: set 3000000 uV; enabling
14LDO_REG6@vcc_1v5: set 1500000 uV; enabling
15LDO_REG7@vcca1v8_codec: set 1800000 uV; enabling
16LDO_REG8@vcc_3v0: set 3000000 uV; enabling
17SWITCH_REG1@vcc3v3_s3: ; enabling (ret: -38)
18SWITCH_REG2@vcc3v3_s0: ; enabling (ret: -38)
19vcc1v8-s0@vcc1v8_s0: set 1800000 uV; enabling (ret: -38)
20dc-12v@dc_12v: set 12000000 uV; enabling (ret: -38)
21vcc-sys@vcc_sys: set 5000000 uV; enabling (ret: -38)
22vcc3v3-sys@vcc3v3_sys: set 3300000 uV; enabling (ret: -38)
23vcc-phy-regulator@vcc_phy: ; enabling (ret: -38)
24vdd-log@vdd_log: ; enabling (ret: -38)
25MMC: sdhci@fe330000: 0, dwmmc@fe320000: 1
26SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
27*** Warning - bad CRC, using default environment
28
29In: serial@ff1a0000
30Out: serial@ff1a0000
31Err: serial@ff1a0000
32Model: Pine64 RockPro64
33normal boot
34Net: eth0: ethernet@fe300000
35Hit any key to stop autoboot: 0
36Card did not respond to voltage select!
37mmc_init: -95, time 20
38Card did not respond to voltage select!
39mmc_init: -95, time 9
40starting USB...
41USB0: USB EHCI 1.00
42USB1: USB EHCI 1.00
43USB2: Register 2000140 NbrPorts 2
44Starting the controller
45USB XHCI 1.10
46USB3: Register 2000140 NbrPorts 2
47Starting the controller
48USB XHCI 1.10
49scanning bus 0 for devices... 1 USB Device(s) found
50scanning bus 1 for devices... 1 USB Device(s) found
51scanning bus 2 for devices... 1 USB Device(s) found
52scanning bus 3 for devices... 2 USB Device(s) found
53 scanning usb for storage devices... 1 Storage Device(s) found
54
55Device 0: Vendor: Samsung Rev: 0 Prod: Portable SSD T5
56 Type: Hard Disk
57 Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
58... is now current device
59Scanning usb 0:7...
60Found /boot/extlinux/extlinux.conf
61Retrieving file: /boot/extlinux/extlinux.conf
622017 bytes read in 192 ms (9.8 KiB/s)
63select kernel
641: kernel-5.4.0-rc1-1120-ayufan-gf8639cacc398
652: kernel-5.4.0-rc1-1120-ayufan-gf8639cacc398-memtest
663: kernel-4.4.190-1233-rockchip-ayufan-gd3f1be0ed310
674: kernel-4.4.190-1233-rockchip-ayufan-gd3f1be0ed310-memtest
68Enter choice: 1: kernel-5.4.0-rc1-1120-ayufan-gf8639cacc398
69Retrieving file: /boot/initrd.img-5.4.0-rc1-1120-ayufan-gf8639cacc398
704551282 bytes read in 417 ms (10.4 MiB/s)
71Retrieving file: /boot/vmlinuz-5.4.0-rc1-1120-ayufan-gf8639cacc398
7231166976 bytes read in 1511 ms (19.7 MiB/s)
73append: rw panic=10 init=/sbin/init coherent_pool=1M ethaddr=62:03:b0:d6:dc:b3 4
74Retrieving file: /boot/dtbs/5.4.0-rc1-1120-ayufan-gf8639cacc398/rockchip/rk3399b
7556621 bytes read in 794 ms (69.3 KiB/s)
76## Flattened Device Tree blob at 01f00000
77 Booting using the fdt blob at 0x1f00000
78 Loading Ramdisk to 7daa9000, end 7df00272 ... OK
79 Loading Device Tree to 000000007da98000, end 000000007daa8d2c ... OK
80
81Starting kernel ...
82
83[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
84[ 0.000000] Linux version 5.4.0-rc1-1120-ayufan-gf8639cacc398 (root@runner-f9
85[ 0.000000] Machine model: Pine64 RockPro64
86[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000ff1a0000 (options '')
87[ 0.000000] printk: bootconsole [uart8250] enabled
88[ 0.000000] efi: Getting EFI parameters from FDT:
89[ 0.000000] efi: UEFI not found.
90[ 0.000000] cma: Reserved 16 MiB at 0x000000007f000000
91[ 0.000000] NUMA: No NUMA configuration found
92[ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x000000007ffffff]
93[ 0.000000] NUMA: NODE_DATA [mem 0x7ebb1800-0x7ebb2fff]
94[ 0.000000] Zone ranges:
95[ 0.000000] DMA32 [mem 0x0000000000200000-0x000000007fffffff]
96[ 0.000000] Normal empty
97[ 0.000000] Movable zone start for each node
98[ 0.000000] Early memory node ranges
99[ 0.000000] node 0: [mem 0x0000000000200000-0x000000007fffffff]
100[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x000000007fffffff]
101[ 0.000000] psci: probing for conduit method from DT.
102[ 0.000000] psci: PSCIv1.0 detected in firmware.
103[ 0.000000] psci: Using standard PSCI v0.2 function IDs
104[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
105[ 0.000000] psci: SMC Calling Convention v1.0
106[ 0.000000] percpu: Embedded 22 pages/cpu s53144 r8192 d28776 u90112
107[ 0.000000] Detected VIPT I-cache on CPU0
108[ 0.000000] CPU features: detected: ARM erratum 845719
109[ 0.000000] CPU features: detected: GIC system register CPU interface
110[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 515592
111[ 0.000000] Policy zone: DMA32
112[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 rw pani4
113[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
114[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes,)
115[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
116[ 0.000000] Memory: 2002432K/2095104K available (18684K kernel code, 2020K r)
117[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
118[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
119[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
120[ 0.000000] Tasks RCU enabled.
121[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 ji.
122[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
123[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
124[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
125[ 0.000000] GICv3: 988 SPIs implemented
126[ 0.000000] GICv3: 0 Extended SPIs implemented
127[ 0.000000] GICv3: Distributor has no Range Selector support
128[ 0.000000] GICv3: 16 PPIs implemented
129[ 0.000000] GICv3: no VLPI support, no direct LPI support
130[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
131[ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
132[ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @7e080000 (flat,)
133[ 0.000000] ITS: using cache flushing for cmd queue
134[ 0.000000] GICv3: using LPI property table @0x000000007e040000
135[ 0.000000] GIC: using cache flushing for LPI property table
136[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x000000007e05000
137[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0}
138[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@1}
139[ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x458 wi0
140[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
141[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless
142[ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398s
143[ 0.003319] Console: colour dummy device 80x25
144[ 0.003750] printk: console [tty0] enabled
145[ 0.004154] printk: bootconsole [uart8250] disabled
146[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
147[ 0.000000] Linux version 5.4.0-rc1-1120-ayufan-gf8639cacc398 (root@runner-f9
148[ 0.000000] Machine model: Pine64 RockPro64
149[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000ff1a0000 (options '')
150[ 0.000000] printk: bootconsole [uart8250] enabled
151[ 0.000000] efi: Getting EFI parameters from FDT:
152[ 0.000000] efi: UEFI not found.
153[ 0.000000] cma: Reserved 16 MiB at 0x000000007f000000
154[ 0.000000] NUMA: No NUMA configuration found
155[ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x000000007ffffff]
156[ 0.000000] NUMA: NODE_DATA [mem 0x7ebb1800-0x7ebb2fff]
157[ 0.000000] Zone ranges:
158[ 0.000000] DMA32 [mem 0x0000000000200000-0x000000007fffffff]
159[ 0.000000] Normal empty
160[ 0.000000] Movable zone start for each node
161[ 0.000000] Early memory node ranges
162[ 0.000000] node 0: [mem 0x0000000000200000-0x000000007fffffff]
163[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x000000007fffffff]
164[ 0.000000] psci: probing for conduit method from DT.
165[ 0.000000] psci: PSCIv1.0 detected in firmware.
166[ 0.000000] psci: Using standard PSCI v0.2 function IDs
167[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
168[ 0.000000] psci: SMC Calling Convention v1.0
169[ 0.000000] percpu: Embedded 22 pages/cpu s53144 r8192 d28776 u90112
170[ 0.000000] Detected VIPT I-cache on CPU0
171[ 0.000000] CPU features: detected: ARM erratum 845719
172[ 0.000000] CPU features: detected: GIC system register CPU interface
173[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 515592
174[ 0.000000] Policy zone: DMA32
175[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 rw pani4
176[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
177[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes,)
178[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
179[ 0.000000] Memory: 2002432K/2095104K available (18684K kernel code, 2020K r)
180[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
181[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
182[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
183[ 0.000000] Tasks RCU enabled.
184[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 ji.
185[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
186[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
187[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
188[ 0.000000] GICv3: 988 SPIs implemented
189[ 0.000000] GICv3: 0 Extended SPIs implemented
190[ 0.000000] GICv3: Distributor has no Range Selector support
191[ 0.000000] GICv3: 16 PPIs implemented
192[ 0.000000] GICv3: no VLPI support, no direct LPI support
193[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
194[ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
195[ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @7e080000 (flat,)
196[ 0.000000] ITS: using cache flushing for cmd queue
197[ 0.000000] GICv3: using LPI property table @0x000000007e040000
198[ 0.000000] GIC: using cache flushing for LPI property table
199[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x000000007e05000
200[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0}
201[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@1}
202[ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x458 wi0
203[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
204[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless
205[ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398s
206[ 0.003319] Console: colour dummy device 80x25
207[ 0.003750] printk: console [tty0] enabled
208[ 0.004154] printk: bootconsole [uart8250] disabled
209[ 0.004736] Calibrating delay loop (skipped), value calculated using timer f)
210[ 0.004772] pid_max: default: 32768 minimum: 301
211[ 0.004914] LSM: Security Framework initializing
212[ 0.005021] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, lin)
213[ 0.005056] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
214[ 0.027377] ASID allocator initialised with 32768 entries
215[ 0.035370] rcu: Hierarchical SRCU implementation.
216[ 0.043516] Platform MSI: interrupt-controller@fee20000 domain created
217[ 0.043956] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@feed
218[ 0.048413] EFI services will not be available.
219[ 0.056435] smp: Bringing up secondary CPUs ...
220[ 0.088659] Detected VIPT I-cache on CPU1
221[ 0.088700] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
222[ 0.088717] GICv3: CPU1: using allocated LPI pending table @0x000000007e06000
223[ 0.088767] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
224[ 0.120728] Detected VIPT I-cache on CPU2
225[ 0.120758] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
226[ 0.120772] GICv3: CPU2: using allocated LPI pending table @0x000000007e07000
227[ 0.120805] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
228[ 0.152826] Detected VIPT I-cache on CPU3
229[ 0.152854] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
230[ 0.152868] GICv3: CPU3: using allocated LPI pending table @0x000000007e10000
231[ 0.152899] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
232[ 0.187628] CPU features: detected: EL2 vector hardening
233[ 0.187968] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware
234[ 0.188347] Detected PIPT I-cache on CPU4
235[ 0.189588] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
236[ 0.190047] GICv3: CPU4: using allocated LPI pending table @0x000000007e11000
237[ 0.191274] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
238[ 0.231304] Detected PIPT I-cache on CPU5
239[ 0.232499] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
240[ 0.232925] GICv3: CPU5: using allocated LPI pending table @0x000000007e12000
241[ 0.234011] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
242[ 0.239071] smp: Brought up 1 node, 6 CPUs
243[ 0.239476] SMP: Total of 6 processors activated.
244[ 0.239508] CPU features: detected: 32-bit EL0 Support
245[ 0.239541] CPU features: detected: CRC32 instructions
246[ 0.464270] CPU: All CPU(s) started at EL2
247[ 0.465124] alternatives: patching kernel code
248[ 0.470350] devtmpfs: initialized
249[ 0.492972] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
250[ 0.493242] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
251[ 0.494956] xor: measuring software checksum speed
252[ 0.536299] 8regs : 1152.000 MB/sec
253[ 0.575952] 32regs : 52.000 MB/sec
254[ 0.616087] arm64_neon: 48.000 MB/sec
255[ 0.616771] xor: using function: 8regs (1152.000 MB/sec)
256[ 0.617729] pinctrl core: initialized pinctrl subsystem
257[ 0.678969] DMI not present or invalid.
258[ 0.699765] NET: Registered protocol family 16
259[ 0.819939] DMA: preallocated 1024 KiB pool for atomic allocations
260[ 0.821100] audit: initializing netlink subsys (disabled)
261[ 0.830569] audit: type=2000 audit(0.824:1): state=initialized audit_enabled1
262[ 0.893904] cpuidle: using governor menu
263[ 0.919761] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
264[ 0.992640] Serial: AMBA PL011 UART driver
265[ 3.626217] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
266[ 3.627344] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
267[ 3.628190] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
268[ 3.629397] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
269[ 3.995666] cryptd: max_cpu_qlen set to 1000
270[ 4.740030] raid6: neonx8 gen() 26 MB/s
271[ 4.806941] raid6: neonx8 xor() 21 MB/s
272[ 4.877000] raid6: neonx4 gen() 23 MB/s
273[ 4.945072] raid6: neonx4 xor() 20 MB/s
274[ 5.015329] raid6: neonx2 gen() 17 MB/s
275[ 5.085071] raid6: neonx2 xor() 20 MB/s
276[ 5.156976] raid6: neonx1 gen() 13 MB/s
277[ 5.224860] raid6: neonx1 xor() 15 MB/s
278[ 5.294649] raid6: int64x8 gen() 12 MB/s
279[ 5.361921] raid6: int64x8 xor() 9 MB/s
280[ 5.433898] raid6: int64x4 gen() 12 MB/s
281[ 5.502898] raid6: int64x4 xor() 10 MB/s
282[ 5.576671] raid6: int64x2 gen() 9 MB/s
283[ 5.643479] raid6: int64x2 xor() 8 MB/s
284[ 5.715955] raid6: int64x1 gen() 6 MB/s
285[ 5.786628] raid6: int64x1 xor() 6 MB/s
286[ 5.787281] raid6: using algorithm neonx8 gen() 26 MB/s
287[ 5.787909] raid6: .... xor() 21 MB/s, rmw enabled
288[ 5.788525] raid6: using neon recovery algorithm
289[ 5.819757] ACPI: Interpreter disabled.
290[ 5.856537] iommu: Default domain type: Translated
291[ 5.879727] rk_iommu ff650800.iommu: IRQ index 1 not found
292[ 5.896331] rk_iommu ff8f3f00.iommu: IRQ index 1 not found
293[ 5.912210] rk_iommu ff903f00.iommu: IRQ index 1 not found
294[ 5.927894] rk_iommu ff914000.iommu: IRQ index 1 not found
295[ 5.943281] rk_iommu ff924000.iommu: IRQ index 1 not found
296[ 5.954814] vgaarb: loaded
297[ 5.970353] SCSI subsystem initialized
298[ 5.992063] usbcore: registered new interface driver usbfs
299[ 5.995168] usbcore: registered new interface driver hub
300[ 5.999976] usbcore: registered new device driver usb
301[ 6.059683] mc: Linux media interface: v0.10
302[ 6.061838] videodev: Linux video capture interface: v2.00
303[ 6.066066] pps_core: LinuxPPS API ver. 1 registered
304[ 6.066784] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giom>
305[ 6.068135] PTP clock support registered
306[ 6.118458] Advanced Linux Sound Architecture Driver Initialized.
307[ 6.141480] Bluetooth: Core ver 2.22
308[ 6.143531] NET: Registered protocol family 31
309[ 6.144210] Bluetooth: HCI device and connection manager initialized
310[ 6.145074] Bluetooth: HCI socket layer initialized
311[ 6.146280] Bluetooth: L2CAP socket layer initialized
312[ 6.147404] Bluetooth: SCO socket layer initialized
313[ 6.148945] NetLabel: Initializing
314[ 6.149947] NetLabel: domain hash size = 128
315[ 6.150517] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
316[ 6.153792] NetLabel: unlabeled traffic allowed by default
317[ 6.191490] clocksource: Switched to clocksource arch_sys_counter
318[ 6.201613] VFS: Disk quotas dquot_6.6.0
319[ 6.205622] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
320[ 6.221984] pnp: PnP ACPI: disabled
321[ 6.551669] thermal_sys: Registered thermal governor 'step_wise'
322[ 6.551861] thermal_sys: Registered thermal governor 'power_allocator'
323[ 6.580892] NET: Registered protocol family 2
324[ 6.612214] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 163)
325[ 6.616101] TCP established hash table entries: 16384 (order: 5, 131072 byte)
326[ 6.627998] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, line)
327[ 6.647829] TCP: Hash tables configured (established 16384 bind 16384)
328[ 6.653925] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
329[ 6.658646] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
330[ 6.669981] NET: Registered protocol family 1
331[ 6.698868] RPC: Registered named UNIX socket transport module.
332[ 6.700492] RPC: Registered udp transport module.
333[ 6.701111] RPC: Registered tcp transport module.
334[ 6.701712] RPC: Registered tcp NFSv4.1 backchannel transport module.
335[ 6.723040] PCI: CLS 0 bytes, default 64
336[ 6.733810] Trying to unpack rootfs image as initramfs...
337[ 22.741905] Freeing initrd memory: 4444K
338[ 22.793331] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counte
339[ 22.809339] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counte
340[ 22.830909] kvm [1]: IPA Size Limit: 40bits
341[ 22.882810] kvm [1]: vgic-v2@fff20000
342[ 22.885235] kvm [1]: GIC system register CPU interface enabled
343[ 22.893587] kvm [1]: vgic interrupt IRQ10
344[ 22.904120] kvm [1]: Hyp mode initialized successfully
345[ 34.025711] workingset: timestamp_bits=44 max_order=19 bucket_order=0
346[ 34.459914] squashfs: version 4.0 (2009/01/31) Phillip Lougher
347[ 34.496857] NFS: Registering the id_resolver key type
348[ 34.498318] Key type id_resolver registered
349[ 34.499614] Key type id_legacy registered
350[ 34.500685] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
351[ 34.501423] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
352[ 34.558520] fuse: init (API version 7.31)
353[ 34.585567] 9p: Installing v9fs 9p2000 file system support
354[ 36.604884] NET: Registered protocol family 38
355[ 36.606030] Key type asymmetric registered
356[ 36.606715] Asymmetric key parser 'x509' registered
357[ 36.609850] Block layer SCSI generic (bsg) driver version 0.4 loaded (major )
358[ 36.616968] io scheduler mq-deadline registered
359[ 36.617851] io scheduler kyber registered
360[ 38.274422] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-0
361[ 38.276454] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Cha2
362[ 38.350274] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-0
363[ 38.352154] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Ch6
364[ 38.859976] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
365[ 38.953072] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 38, base_baud =A
366[ 38.988040] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 39, base_baud =A
367[ 39.308186] printk: console [ttyS2] enabled
368[ 39.393969] SuperH (H)SCI(F) driver initialized
369[ 39.440204] msm_serial: driver initialized
370[ 40.172065] cacheinfo: Unable to detect cache hierarchy for CPU 0
371[ 40.610748] brd: module loaded
372[ 41.064539] loop: module loaded
373[ 42.392380] spi-nor spi0.0: gd25q128 (16384 Kbytes)
374[ 42.861683] rockchip-spi ff1d0000.spi: chipselect 0 already in use
375[ 42.864404] spi_master spi0: spi_device register error /spi@ff1d0000/spi-fla0
376[ 42.866625] spi_master spi0: Failed to create SPI device for /spi@ff1d0000/s0
377[ 42.991871] libphy: Fixed MDIO Bus: probed
378[ 43.036728] tun: Universal TUN/TAP device driver, 1.6
379[ 43.140427] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
380[ 43.142062] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
381[ 43.145981] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k
382[ 43.148344] igb: Copyright (c) 2007-2014 Intel Corporation.
383[ 43.152140] igbvf: Intel(R) Gigabit Virtual Function Network Driver - versiok
384[ 43.154107] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
385[ 43.190403] sky2: driver version 1.30
386[ 43.303926] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
387[ 43.305942] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
388[ 43.312373] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
389[ 43.314614] rk_gmac-dwmac fe300000.ethernet: no regulator found
390[ 43.316893] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
391[ 43.318826] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
392[ 43.321016] rk_gmac-dwmac fe300000.ethernet: RX delay(0x20).
393[ 43.322751] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
394[ 43.328355] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
395[ 43.330178] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
396[ 43.337653] rk_gmac-dwmac fe300000.ethernet: init for RGMII
397[ 43.345164] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
398[ 43.348114] rk_gmac-dwmac fe300000.ethernet: DWMAC1000
399[ 43.349747] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register suppd
400[ 43.352287] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine suppd
401[ 43.354285] rk_gmac-dwmac fe300000.ethernet: COE Type 2
402[ 43.356275] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
403[ 43.358094] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
404[ 43.361415] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
405[ 43.363600] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
406[ 43.365217] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watr
407[ 44.264209] libphy: stmmac: probed
408[ 44.265952] RTL8211F Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8)
409[ 44.269491] RTL8211F Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8)
410[ 44.392283] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet drr
411[ 44.397571] usbcore: registered new interface driver pegasus
412[ 44.401566] usbcore: registered new interface driver rtl8150
413[ 44.405433] usbcore: registered new interface driver r8152
414[ 44.409181] usbcore: registered new interface driver asix
415[ 44.412844] usbcore: registered new interface driver ax88179_178a
416[ 44.416807] usbcore: registered new interface driver cdc_ether
417[ 44.420581] usbcore: registered new interface driver dm9601
418[ 44.424325] usbcore: registered new interface driver CoreChips
419[ 44.428302] usbcore: registered new interface driver smsc75xx
420[ 44.432544] usbcore: registered new interface driver smsc95xx
421[ 44.436279] usbcore: registered new interface driver net1080
422[ 44.439941] usbcore: registered new interface driver plusb
423[ 44.443591] usbcore: registered new interface driver cdc_subset
424[ 44.446869] usbcore: registered new interface driver MOSCHIP usb-ethernet drr
425[ 44.452283] usbcore: registered new interface driver cdc_ncm
426[ 44.460637] VFIO - User Level meta-driver version: 0.3
427[ 44.585098] OF: graph: no port node found in /syscon@ff770000/usb2-phy@e450/t
428[ 44.588156] dwc3 fe800000.dwc3: IRQ otg not found
429[ 44.589735] dwc3 fe800000.dwc3: IRQ dwc_usb3 not found
430[ 44.600085] dwc3 fe800000.dwc3: IRQ host not found
431[ 44.601824] dwc3 fe800000.dwc3: IRQ dwc_usb3 not found
432[ 44.684732] dwc3 fe900000.dwc3: IRQ host not found
433[ 44.686612] dwc3 fe900000.dwc3: IRQ dwc_usb3 not found
434[ 44.791908] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
435[ 44.793811] ehci-pci: EHCI PCI platform driver
436[ 44.797439] ehci-platform: EHCI generic platform driver
437[ 44.813615] ehci-platform fe380000.usb: EHCI Host Controller
438[ 44.816795] ehci-platform fe380000.usb: new USB bus registered, assigned bus1
439[ 44.824029] ehci-platform fe380000.usb: irq 31, io mem 0xfe380000
440[ 44.840749] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
441[ 44.873665] hub 1-0:1.0: USB hub found
442[ 44.876892] hub 1-0:1.0: 1 port detected
443[ 44.907678] ehci-platform fe3c0000.usb: EHCI Host Controller
444[ 44.910362] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus2
445[ 44.917691] ehci-platform fe3c0000.usb: irq 33, io mem 0xfe3c0000
446[ 44.936596] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
447[ 44.966039] hub 2-0:1.0: USB hub found
448[ 44.969520] hub 2-0:1.0: 1 port detected
449[ 45.005026] ehci-orion: EHCI orion driver
450[ 45.018316] ehci-exynos: EHCI EXYNOS driver
451[ 45.030237] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
452[ 45.033059] ohci-pci: OHCI PCI platform driver
453[ 45.037555] ohci-platform: OHCI generic platform driver
454[ 45.049287] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
455[ 45.052381] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus3
456[ 45.060157] ohci-platform fe3a0000.usb: irq 32, io mem 0xfe3a0000
457[ 45.152731] hub 3-0:1.0: USB hub found
458[ 45.156294] hub 3-0:1.0: 1 port detected
459[ 45.181744] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
460[ 45.184858] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus4
461[ 45.191699] ohci-platform fe3e0000.usb: irq 34, io mem 0xfe3e0000
462[ 45.289565] hub 4-0:1.0: USB hub found
463[ 45.292780] hub 4-0:1.0: 1 port detected
464[ 45.322704] ohci-exynos: OHCI EXYNOS driver
465[ 45.366982] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
466[ 45.370234] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus n5
467[ 45.377686] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110
468[ 45.381297] xhci-hcd xhci-hcd.0.auto: irq 228, io mem 0xfe800000
469[ 45.418023] hub 5-0:1.0: USB hub found
470[ 45.421246] hub 5-0:1.0: 1 port detected
471[ 45.441555] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
472[ 45.444335] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus n6
473[ 45.446746] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
474[ 45.452295] usb usb6: We don't know the algorithms for LPM for this host, di.
475[ 45.482723] hub 6-0:1.0: USB hub found
476[ 45.485808] hub 6-0:1.0: 1 port detected
477[ 45.510614] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
478[ 45.513534] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus n7
479[ 45.521273] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110
480[ 45.526217] xhci-hcd xhci-hcd.1.auto: irq 229, io mem 0xfe900000
481[ 45.570820] hub 7-0:1.0: USB hub found
482[ 45.574341] hub 7-0:1.0: 1 port detected
483[ 45.592558] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
484[ 45.594584] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus n8
485[ 45.597540] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
486[ 45.602880] usb usb8: We don't know the algorithms for LPM for this host, di.
487[ 45.633223] hub 8-0:1.0: USB hub found
488[ 45.636508] hub 8-0:1.0: 1 port detected
489[ 45.678507] usbcore: registered new interface driver usb-storage
490[ 45.996544] i2c /dev entries driver
491[ 46.190286] rk808 0-001b: chip id: 0x0
492[ 46.348035] rk808-rtc rk808-rtc: registered as rtc0
493[ 46.584975] rockchip-rga ff680000.rga: HW Version: 0x03.02
494[ 46.599868] rockchip-rga ff680000.rga: Registered rockchip-rga as /dev/video0
495[ 46.915584] Bluetooth: HCI UART driver ver 2.3
496[ 47.002668] sdhci: Secure Digital Host Controller Interface driver
497[ 47.005037] sdhci: Copyright(c) Pierre Ossman
498[ 47.029394] Synopsys Designware Multimedia Card Interface Driver
499[ 47.094293] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mod.
500[ 47.097592] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
501[ 47.100112] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
502[ 47.103960] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 28,32 bio
503[ 47.110484] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
504[ 47.112833] mmc_host mmc0: card is non-removable.
505[ 47.141851] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz,)
506[ 47.186138] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mod.
507[ 47.189451] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
508[ 47.192003] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
509[ 47.195800] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 29,32 bio
510[ 47.201579] dwmmc_rockchip fe320000.dwmmc: Got CD GPIO
511[ 47.223678] mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
512[ 47.230593] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
513[ 47.232284] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz,)
514[ 47.239613] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
515[ 47.250608] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
516[ 47.313825] sdhci-pltfm: SDHCI platform and OF driver helper
517[ 47.325629] random: fast init done
518[ 47.387662] mmc2: CQHCI version 5.10
519[ 47.432627] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 5000000)
520[ 47.434941] mmc2: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using A
521[ 47.637048] ledtrig-cpu: registered to indicate activity on CPUs
522[ 47.731746] usbcore: registered new interface driver usbhid
523[ 47.733427] usbhid: USB HID core driver
524[ 47.841578] dwmmc_rockchip fe310000.dwmmc: All phases work, using default ph.
525[ 48.002650] mmc0: new ultra high speed SDR104 SDIO card at address 0001
526[ 48.346378] xt_time: kernel timezone is -0000
527[ 48.350002] IPVS: Registered protocols (TCP, UDP, SCTP, AH, ESP)
528[ 48.353603] IPVS: Connection hash table configured (size=4096, memory=64Kbyt)
529[ 48.365176] IPVS: ipvs loaded.
530[ 48.366415] IPVS: [rr] scheduler registered.
531[ 48.368207] IPVS: [wrr] scheduler registered.
532[ 48.369503] IPVS: [lc] scheduler registered.
533[ 48.370696] IPVS: [wlc] scheduler registered.
534[ 48.372476] IPVS: [fo] scheduler registered.
535[ 48.373729] IPVS: [ovf] scheduler registered.
536[ 48.376052] IPVS: [lblc] scheduler registered.
537[ 48.377664] IPVS: [lblcr] scheduler registered.
538[ 48.379670] IPVS: [dh] scheduler registered.
539[ 48.380942] IPVS: [sh] scheduler registered.
540[ 48.382140] IPVS: [sed] scheduler registered.
541[ 48.383831] IPVS: [nq] scheduler registered.
542[ 48.406904] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
543[ 48.415678] Initializing XFRM netlink socket
544[ 48.450062] NET: Registered protocol family 10
545[ 48.509819] Segment Routing with IPv6
546[ 48.533069] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
547[ 48.563979] NET: Registered protocol family 17
548[ 48.567982] bridge: filtering via arp/ip/ip6tables is no longer available by.
549[ 48.576086] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
550[ 48.577981] Bluetooth: HIDP socket layer initialized
551[ 48.581605] 8021q: 802.1Q VLAN Support v1.8
552[ 48.590874] 9pnet: Installing 9P2000 support
553[ 48.594666] Key type dns_resolver registered
554[ 48.631914] registered taskstats version 1
555[ 48.697696] Btrfs loaded, crc32c=crc32c-generic
556[ 50.721934] input: gpio-keys as /devices/platform/gpio-keys/input/input0
557[ 50.757314] rk808-rtc rk808-rtc: setting system clock to 2013-01-18T09:04:32)
558[ 50.760368] of_cfs_init
559[ 50.763728] of_cfs_init: OK
560[ 50.780448] ALSA device list:
561[ 50.781250] No soundcards found.
562[ 50.782977] platform regulatory.0: Direct firmware load for regulatory.db fa2
563[ 50.783018] ttyS2 - failed to request DMA
564[ 50.785012] cfg80211: failed to load regulatory.db
565[ 50.785850] Freeing unused kernel memory: 1408K
566[ 50.818922] Run /init as init process
567Loading, please wait...
568[ 52.034365] tmpfs: Unknown parameter 'size'
569mount: Invalid argument
570Starting version 241
571Begin: Loading essential drivers ... done.
572Begin: Running /scripts/init-premount ... done.
573Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
574Begin: Running /scripts/local-premount ... done.
575Begin: Waiting for root file system ... Begin: Running /scripts/local-block ....
576Begin: Running /scripts/local-block ... done.
577[ 97.825873] random: crng init done
578Begin: Running /scripts/local-block ... done.
579Begin: Running /scripts/local-block ... done.
580Begin: Running /scripts/local-block ... done.
581done.