· 6 years ago · Sep 04, 2019, 09:50 AM
1U-Boot SPL 2018.11-stm32mp-r2 (Nov 14 2018 - 16:10:06 +0000)
2Model: STMicroelectronics STM32MP157C-DK2 Discovery Board
3RAM: DDR3-1066/888 bin G 1x4Gb 533MHz v1.41
4Trying to boot from MMC1
5
6
7U-Boot 2018.11-stm32mp-r2 (Nov 14 2018 - 16:10:06 +0000)
8
9CPU: STM32MP157CAC Rev.B
10Model: STMicroelectronics STM32MP157C-DK2 Discovery Board
11Board: stm32mp1 in basic mode (st,stm32mp157c-dk2)
12Board: MB1272 Var2 Rev.C-01
13 Watchdog enabled
14DRAM: 512 MiB
15Clocks:
16- MPU : 650 MHz
17- MCU : 208.878 MHz
18- AXI : 266.500 MHz
19- PER : 24 MHz
20- DDR : 533 MHz
21
22*******************************************
23* WARNING 500mA power supply detected *
24* Current too low, use a 3A power supply! *
25*******************************************
26
27NAND: 0 MiB
28MMC: STM32 SDMMC2: 0, STM32 SDMMC2: 1
29In: serial
30Out: serial
31Err: serial
32Net: eth0: ethernet@5800a000
33Boot over mmc0!
34Hit any key to stop autoboot: 1 0
35switch to partitions #0, OK
36mmc0 is current device
37Scanning mmc 0:4...
38Found U-Boot script /boot.scr.uimg
391553 bytes read in 1 ms (1.5 MiB/s)
40## Executing script at c4100000
41Scanning mmc 0:4...
42Found /mmc0_stm32mp157c-dk2_extlinux/extlinux.conf
43Retrieving file: /mmc0_stm32mp157c-dk2_extlinux/extlinux.conf
44616 bytes read in 1 ms (601.6 KiB/s)
45Retrieving file: /mmc0_stm32mp157c-dk2_extlinux/../splash.bmp
4646180 bytes read in 3 ms (14.7 MiB/s)
47Select the boot mode
481: stm32mp157c-dk2-sdcard
492: stm32mp157c-dk2-a7-examples-sdcard
503: stm32mp157c-dk2-m4-examples-sdcard
51Enter choice: 1: stm32mp157c-dk2-sdcard
52Retrieving file: /uImage
536569464 bytes read in 288 ms (21.8 MiB/s)
54append: root=/dev/mmcblk0p6 rootwait rw console=ttySTM0,115200
55Retrieving file: /stm32mp157c-dk2.dtb
5669510 bytes read in 4 ms (16.6 MiB/s)
57## Booting kernel from Legacy Image at c2000000 ...
58 Image Name: Linux-4.19.9
59 Image Type: ARM Linux Kernel Image (uncompressed)
60 Data Size: 6569400 Bytes = 6.3 MiB
61 Load Address: c2000040
62 Entry Point: c2000040
63 Verifying Checksum ... OK
64## Flattened Device Tree blob at c4000000
65 Booting using the fdt blob at 0xc4000000
66 XIP Kernel Image ... OK
67 Using Device Tree in place at c4000000, end c4013f85
68
69Starting kernel ...
70
71[ 0.000000] Booting Linux on physical CPU 0x0
72[ 0.000000] Linux version 4.19.9 (oe-user@oe-host) (gcc version 8.2.0 (GCC)) #1 SMP PREEMPT Thu Dec 13 08:16:23 UTC 2018
73[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
74[ 0.000000] CPU: div instructions available: patching division code
75[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
76[ 0.000000] OF: fdt: Machine model: STMicroelectronics STM32MP157C-DK2 Discovery Board
77[ 0.000000] Memory policy: Data cache writealloc
78[ 0.000000] Reserved memory: created DMA memory pool at 0x10000000, size 0 MiB
79[ 0.000000] OF: reserved mem: initialized node mcuram2@0x10000000, compatible id shared-dma-pool
80[ 0.000000] Reserved memory: created DMA memory pool at 0x10040000, size 0 MiB
81[ 0.000000] OF: reserved mem: initialized node vdev0vring0@10040000, compatible id shared-dma-pool
82[ 0.000000] Reserved memory: created DMA memory pool at 0x10042000, size 0 MiB
83[ 0.000000] OF: reserved mem: initialized node vdev0vring1@10042000, compatible id shared-dma-pool
84[ 0.000000] Reserved memory: created DMA memory pool at 0x10044000, size 0 MiB
85[ 0.000000] OF: reserved mem: initialized node vdev0buffer@10044000, compatible id shared-dma-pool
86[ 0.000000] Reserved memory: created DMA memory pool at 0x30000000, size 0 MiB
87[ 0.000000] OF: reserved mem: initialized node mcuram@0x30000000, compatible id shared-dma-pool
88[ 0.000000] Reserved memory: created DMA memory pool at 0x38000000, size 0 MiB
89[ 0.000000] OF: reserved mem: initialized node retram@0x38000000, compatible id shared-dma-pool
90[ 0.000000] cma: Reserved 128 MiB at 0xd4000000
91[ 0.000000] psci: probing for conduit method from DT.
92[ 0.000000] psci: PSCIv1.0 detected in firmware.
93[ 0.000000] psci: Using standard PSCI v0.2 function IDs
94[ 0.000000] psci: Trusted OS migration not required
95[ 0.000000] psci: SMC Calling Convention v1.0
96[ 0.000000] random: get_random_bytes called from start_kernel+0xa0/0x494 with crng_init=0
97[ 0.000000] percpu: Embedded 17 pages/cpu @(ptrval) s40204 r8192 d21236 u69632
98[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 113680
99[ 0.000000] Kernel command line: root=/dev/mmcblk0p6 rootwait rw console=ttySTM0,115200
100[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
101[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
102[ 0.000000] Memory: 306144K/458752K available (10240K kernel code, 816K rwdata, 2860K rodata, 1024K init, 208K bss, 21536K reserved, 131072K cma-reserved, 0K highmem)
103[ 0.000000] Virtual kernel memory layout:
104[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
105[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
106[ 0.000000] vmalloc : 0xdc800000 - 0xff800000 ( 560 MB)
107[ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
108[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
109[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
110[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (11232 kB)
111[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
112[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 817 kB)
113[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 209 kB)
114[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
115[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
116[ 0.000000] rcu: RCU event tracing is enabled.
117[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
118[ 0.000000] Tasks RCU enabled.
119[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
120[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
121[ 0.000000] /soc/interrupt-controller@5000d000: bank0
122[ 0.000000] /soc/interrupt-controller@5000d000: bank1
123[ 0.000000] /soc/interrupt-controller@5000d000: bank2
124[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
125[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
126[ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
127[ 0.000026] Switching to timer-based delay loop, resolution 41ns
128[ 0.001916] Console: colour dummy device 80x30
129[ 0.001968] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
130[ 0.001992] pid_max: default: 32768 minimum: 301
131[ 0.002228] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
132[ 0.002250] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
133[ 0.003262] CPU: Testing write buffer coherency: ok
134[ 0.003760] CPU0: update cpu_capacity 1024
135[ 0.003782] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
136[ 0.059784] Setting up static identity map for 0xc0100000 - 0xc0100060
137[ 0.079775] rcu: Hierarchical SRCU implementation.
138[ 0.119922] smp: Bringing up secondary CPUs ...
139[ 0.200283] CPU1: update cpu_capacity 1024
140[ 0.200295] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
141[ 0.200500] smp: Brought up 1 node, 2 CPUs
142[ 0.200529] SMP: Total of 2 processors activated (96.00 BogoMIPS).
143[ 0.200539] CPU: All CPU(s) started in SVC mode.
144[ 0.201679] devtmpfs: initialized
145[ 0.226978] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
146[ 0.227503] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
147[ 0.227535] futex hash table entries: 512 (order: 3, 32768 bytes)
148[ 0.233618] pinctrl core: initialized pinctrl subsystem
149[ 0.235745] NET: Registered protocol family 16
150[ 0.242971] DMA: preallocated 256 KiB pool for atomic coherent allocations
151[ 0.245449] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
152[ 0.245471] hw-breakpoint: maximum watchpoint size is 8 bytes.
153[ 0.245766] Serial: AMBA PL011 UART driver
154[ 0.247936] stm32-pm-domain pm_domain: domain core-ret-power-domain registered
155[ 0.247974] stm32-pm-domain pm_domain: subdomain core-power-domain registered
156[ 0.247989] stm32-pm-domain pm_domain: domains probed
157[ 0.263461] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOA bank added
158[ 0.263822] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOB bank added
159[ 0.264115] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOC bank added
160[ 0.264381] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOD bank added
161[ 0.264657] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOE bank added
162[ 0.264930] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOF bank added
163[ 0.265191] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOG bank added
164[ 0.265470] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOH bank added
165[ 0.265729] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOI bank added
166[ 0.265935] stm32mp157-pinctrl soc:pin-controller@50002000: Pinctrl STM32 initialized
167[ 0.266787] stm32mp157-pinctrl soc:pin-controller-z@54004000: GPIOZ bank added
168[ 0.266815] stm32mp157-pinctrl soc:pin-controller-z@54004000: Pinctrl STM32 initialized
169[ 0.286596] stm32-mdma 58000000.dma: STM32 MDMA driver registered
170[ 0.291804] SCSI subsystem initialized
171[ 0.292572] usbcore: registered new interface driver usbfs
172[ 0.292663] usbcore: registered new interface driver hub
173[ 0.292805] usbcore: registered new device driver usb
174[ 0.293122] pps_core: LinuxPPS API ver. 1 registered
175[ 0.293135] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
176[ 0.293168] PTP clock support registered
177[ 0.293450] EDAC MC: Ver: 3.0.0
178[ 0.294368] Advanced Linux Sound Architecture Driver Initialized.
179[ 0.296009] clocksource: Switched to clocksource arch_sys_counter
180[ 0.389876] NET: Registered protocol family 2
181[ 0.390941] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
182[ 0.390992] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
183[ 0.391059] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
184[ 0.391156] TCP: Hash tables configured (established 4096 bind 4096)
185[ 0.391303] UDP hash table entries: 256 (order: 1, 8192 bytes)
186[ 0.391349] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
187[ 0.391833] NET: Registered protocol family 1
188[ 0.392779] RPC: Registered named UNIX socket transport module.
189[ 0.392802] RPC: Registered udp transport module.
190[ 0.392812] RPC: Registered tcp transport module.
191[ 0.392822] RPC: Registered tcp NFSv4.1 backchannel transport module.
192[ 0.393903] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
193[ 0.396176] Initialise system trusted keyrings
194[ 0.396543] workingset: timestamp_bits=14 max_order=17 bucket_order=3
195[ 0.407370] squashfs: version 4.0 (2009/01/31) Phillip Lougher
196[ 0.408470] NFS: Registering the id_resolver key type
197[ 0.408536] Key type id_resolver registered
198[ 0.408549] Key type id_legacy registered
199[ 0.408768] ntfs: driver 2.1.32 [Flags: R/O].
200[ 0.409263] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
201[ 0.410192] fuse init (API version 7.27)
202[ 0.410883] pstore: using deflate compression
203[ 0.413791] NET: Registered protocol family 38
204[ 0.413820] Key type asymmetric registered
205[ 0.413834] Asymmetric key parser 'x509' registered
206[ 0.413929] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
207[ 0.413947] io scheduler noop registered
208[ 0.413959] io scheduler deadline registered
209[ 0.414222] io scheduler cfq registered (default)
210[ 0.414238] io scheduler mq-deadline registered
211[ 0.414250] io scheduler kyber registered
212[ 0.415557] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.1
213[ 0.415700] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.2
214[ 0.415827] stm32-usbphyc 5a006000.usbphyc: Dropping the link to regulator.2
215[ 0.415939] stm32-usbphyc 5a006000.usbphyc: Dropping the link to regulator.1
216[ 0.420769] stm32-dma 48000000.dma: STM32 DMA driver registered
217[ 0.422559] stm32-dma 48001000.dma: STM32 DMA driver registered
218[ 0.502464] STM32 USART driver initialized
219[ 0.503813] 4000e000.serial: ttySTM3 at MMIO 0x4000e000 (irq = 25, base_baud = 4000000) is a stm32-usart
220[ 0.504116] serial serial0: tty port ttySTM3 registered
221[ 0.504176] stm32-usart 4000e000.serial: interrupt mode used for rx (no dma)
222[ 0.504193] stm32-usart 4000e000.serial: interrupt mode used for tx (no dma)
223[ 0.505394] 40010000.serial: ttySTM0 at MMIO 0x40010000 (irq = 27, base_baud = 4000000) is a stm32-usart
224[ 1.454135] console [ttySTM0] enabled
225[ 1.458368] stm32-usart 40010000.serial: interrupt mode used for rx (no dma)
226[ 1.464834] stm32-usart 40010000.serial: interrupt mode used for tx (no dma)
227[ 1.479780] stm32-display-dsi 5a000000.dsi: Linked as a consumer to regulator.2
228[ 1.489069] panel-orisetech-otm8009a 5a000000.dsi.0: 5a000000.dsi.0 supply power not found, using dummy regulator
229[ 1.498136] panel-orisetech-otm8009a 5a000000.dsi.0: Linked as a consumer to regulator.0
230[ 1.521395] brd: module loaded
231[ 1.535859] loop: module loaded
232[ 1.543734] libphy: Fixed MDIO Bus: probed
233[ 1.547936] CAN device driver interface
234[ 1.552711] stm32-dwmac 5800a000.ethernet: PTP uses main clock
235[ 1.557183] stm32-dwmac 5800a000.ethernet: no reset control found
236[ 1.563274] stm32-dwmac 5800a000.ethernet: No phy clock provided...
237[ 1.570655] stm32-dwmac 5800a000.ethernet: User ID: 0x40, Synopsys ID: 0x42
238[ 1.576580] stm32-dwmac 5800a000.ethernet: DWMAC4/5
239[ 1.581509] stm32-dwmac 5800a000.ethernet: DMA HW capability register supported
240[ 1.588954] stm32-dwmac 5800a000.ethernet: RX Checksum Offload Engine supported
241[ 1.596229] stm32-dwmac 5800a000.ethernet: TX Checksum insertion supported
242[ 1.603105] stm32-dwmac 5800a000.ethernet: Wake-Up On Lan supported
243[ 1.609439] stm32-dwmac 5800a000.ethernet: TSO supported
244[ 1.614739] stm32-dwmac 5800a000.ethernet: TSO feature enabled
245[ 1.620624] stm32-dwmac 5800a000.ethernet: Enable RX Mitigation via HW Watchdog Timer
246[ 1.628733] libphy: stmmac: probed
247[ 1.634641] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
248[ 1.640872] usbcore: registered new interface driver pegasus
249[ 1.646492] usbcore: registered new interface driver asix
250[ 1.651770] usbcore: registered new interface driver ax88179_178a
251[ 1.657935] usbcore: registered new interface driver cdc_ether
252[ 1.663762] usbcore: registered new interface driver smsc75xx
253[ 1.669612] usbcore: registered new interface driver smsc95xx
254[ 1.675286] usbcore: registered new interface driver net1080
255[ 1.681024] usbcore: registered new interface driver cdc_subset
256[ 1.686958] usbcore: registered new interface driver zaurus
257[ 1.692539] usbcore: registered new interface driver cdc_ncm
258[ 1.699404] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
259[ 1.704744] ehci-platform: EHCI generic platform driver
260[ 1.710541] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
261[ 1.716280] ohci-platform: OHCI generic platform driver
262[ 1.722133] usbcore: registered new interface driver usb-storage
263[ 1.732362] stm32_rtc 5c004000.rtc: rtc core: registered 5c004000.rtc as rtc0
264[ 1.738595] stm32_rtc 5c004000.rtc: Date/Time must be initialized
265[ 1.744195] stm32_rtc 5c004000.rtc: registered rev:1.2
266[ 1.750030] i2c /dev entries driver
267[ 1.773570] stm32f7-i2c 40012000.i2c: can't use DMA
268[ 1.780693] sii902x 0-0039: Failed to get supply 'iovcc': -517
269[ 1.786174] stm32f7-i2c 40012000.i2c: STM32F7 I2C-0 bus adapter
270[ 1.811909] stm32f7-i2c 5c002000.i2c: can't use DMA
271[ 1.817609] typec_stusb 1-0028: STUSB driver registered
272[ 1.823206] stpmic1 1-0033: PMIC Chip Version: 0x10
273[ 1.832458] BUCK1: supplied by regulator-dummy
274[ 1.839463] BUCK2: supplied by regulator-dummy
275[ 1.845896] BUCK3: supplied by regulator-dummy
276[ 1.852875] BUCK4: supplied by regulator-dummy
277[ 1.859406] LDO1: supplied by v3v3
278[ 1.867018] LDO2: supplied by regulator-dummy
279[ 1.873753] LDO3: supplied by vdd_ddr
280[ 1.879974] LDO4: supplied by regulator-dummy
281[ 1.884510] LDO5: supplied by regulator-dummy
282[ 1.891376] LDO6: supplied by v3v3
283[ 1.897225] VREF_DDR: supplied by regulator-dummy
284[ 1.903676] BOOST: supplied by regulator-dummy
285[ 1.907907] VBUS_OTG: supplied by bst_out
286[ 1.911825] SW_OUT: supplied by bst_out
287[ 1.917447] random: fast init done
288[ 1.921106] input: pmic_onkey as /devices/platform/soc/5c002000.i2c/i2c-1/1-0033/5c002000.i2c:stpmic@33:onkey/input/input0
289[ 1.931407] stm32f7-i2c 5c002000.i2c: STM32F7 I2C-1 bus adapter
290[ 1.940500] stm_thermal 50028000.thermal: stm_thermal_probe: Driver initialized successfully
291[ 1.951077] mmci-pl18x 58005000.sdmmc: Linked as a consumer to regulator.8
292[ 1.956852] mmci-pl18x 58005000.sdmmc: mmc0: PL180 manf 53 rev2 at 0x58005000 irq 58,0 (pio)
293[ 1.994027] mmci-pl18x 58007000.sdmmc: allocated mmc-pwrseq
294[ 1.998596] mmci-pl18x 58007000.sdmmc: Linked as a consumer to regulator.8
295[ 2.006365] mmci-pl18x 58007000.sdmmc: mmc1: PL180 manf 53 rev1 at 0x58007000 irq 59,0 (pio)
296[ 2.040526] sdhci: Secure Digital Host Controller Interface driver
297[ 2.046467] sdhci: Copyright(c) Pierre Ossman
298[ 2.049698] mmc0: host does not support reading read-only switch, assuming write-enable
299[ 2.057757] Synopsys Designware Multimedia Card Interface Driver
300[ 2.065460] sdhci-pltfm: SDHCI platform and OF driver helper
301[ 2.072986] mmc0: new high speed SDHC card at address aaaa
302[ 2.079421] ledtrig-cpu: registered to indicate activity on CPUs
303[ 2.079591] mmcblk0: mmc0:aaaa SU04G 3.69 GiB
304[ 2.085055] usbcore: registered new interface driver usbhid
305[ 2.094105] usbhid: USB HID core driver
306[ 2.094588] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
307[ 2.104750] stm32-ipcc 4c001000.mailbox: ipcc rev:1.0 enabled, 6 chans, proc 0
308[ 2.105842] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
309[ 2.111846] stm32-rproc m4@0: wdg irq registered
310[ 2.118463] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
311[ 2.121066] remoteproc remoteproc0: m4 is available
312[ 2.129586] GPT:Primary header thinks Alt. header is not at the end of the disk.
313[ 2.132033] vref: supplied by vdd
314[ 2.138788] GPT:3145727 != 7744511
315[ 2.142227] stm32-adc-core 48003000.adc: Linked as a consumer to regulator.4
316[ 2.145414] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
317[ 2.152697] stm32-adc-core 48003000.adc: Linked as a consumer to regulator.7
318[ 2.158026] GPT:Alternate GPT header not at the end of the disk.
319[ 2.158032] GPT:3145727 != 7744511
320[ 2.158036] GPT: Use GNU Parted to correct GPT errors.
321[ 2.158123] mmcblk0: p1 p2 p3 p4 p5 p6 p7
322[ 2.185408] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
323[ 2.191970] mmc1: queuing unknown CIS tuple 0x80 (6 bytes)
324[ 2.209098] iio iio:device2: Can't get offset/scale: -517
325[ 2.216445] optee: probing for conduit method from DT.
326[ 2.220148] optee: api uid mismatch
327[ 2.233235] NET: Registered protocol family 17
328[ 2.236396] can: controller area network core (rev 20170425 abi 9)
329[ 2.242567] NET: Registered protocol family 29
330[ 2.246998] can: raw protocol (rev 20170425)
331[ 2.251189] can: broadcast manager protocol (rev 20170425 t)
332[ 2.256946] can: netlink gateway (rev 20170425) max_hops=1
333[ 2.262972] Key type dns_resolver registered
334[ 2.266910] ThumbEE CPU extension supported.
335[ 2.270966] Registering SWP/SWPB emulation handler
336[ 2.278362] registered taskstats version 1
337[ 2.280979] mmc1: new high speed SDIO card at address 0001
338[ 2.281008] Loading compiled-in X.509 certificates
339[ 2.316969] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.1
340[ 2.322952] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.2
341[ 2.330443] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.12
342[ 2.338489] stm32-usbphyc 5a006000.usbphyc: registered rev:1.0
343[ 2.345509] dwc2 49000000.usb-otg: 49000000.usb-otg supply vusb_d not found, using dummy regulator
344[ 2.353354] dwc2 49000000.usb-otg: Linked as a consumer to regulator.0
345[ 2.359694] dwc2 49000000.usb-otg: 49000000.usb-otg supply vusb_a not found, using dummy regulator
346[ 2.381252] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM
347[ 2.388939] ehci-platform 5800d000.usbh-ehci: EHCI Host Controller
348[ 2.393725] ehci-platform 5800d000.usbh-ehci: new USB bus registered, assigned bus number 1
349[ 2.402660] ehci-platform 5800d000.usbh-ehci: irq 63, io mem 0x5800d000
350[ 2.436061] ehci-platform 5800d000.usbh-ehci: USB 2.0 started, EHCI 1.00
351[ 2.442650] hub 1-0:1.0: USB hub found
352[ 2.445150] hub 1-0:1.0: 2 ports detected
353[ 2.452233] sii902x 0-0039: Linked as a consumer to regulator.10
354[ 2.456959] sii902x 0-0039: Linked as a consumer to regulator.14
355[ 2.467035] i2c i2c-0: Added multiplexed i2c bus 2
356[ 2.472956] cs42l51 0-004a: Linked as a consumer to regulator.8
357[ 2.477605] cs42l51 0-004a: Linked as a consumer to regulator.9
358[ 2.486134] cs42l51 0-004a: Cirrus Logic CS42L51, Revision: 01
359[ 2.494212] asoc-audio-graph-card sound: cs42l51-hifi0 <-> 4400b004.audio-controller mapping ok
360[ 2.502457] asoc-audio-graph-card sound: cs42l51-hifi1 <-> 4400b024.audio-controller mapping ok
361[ 2.510750] asoc-audio-graph-card sound: i2s-hifi <-> 4000b000.audio-controller mapping ok
362[ 2.519838] cs42l51 0-004a: ASoC: mux DAC Mux has no paths
363[ 2.759393] [drm] ltdc hw version 0x00010300 - ready
364[ 2.763009] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
365[ 2.769627] [drm] Driver supports precise vblank timestamp query.
366[ 2.776575] [drm] Initialized stm 1.0.0 20170330 for 5a001000.display-controller on minor 0
367[ 2.785135] stm32_rtc 5c004000.rtc: setting system clock to 2000-01-01 00:02:02 UTC (946684922)
368[ 2.793916] vdda: disabling
369[ 2.796065] ALSA device list:
370[ 2.798591] #0: STM32MP[ 2.816126] usb 1-1: new high-speed USB device number 2 using ehci-platform
371[ 2.916771] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
372[ 2.923508] VFS: Mounted root (ext4 filesystem) on device 179:6.
373[ 2.935711] devtmpfs: mounted
374[ 2.939148] Freeing unused kernel memory: 1024K
375[ 2.942553] Run /sbin/init as init process
376[ 3.017647] hub 1-1:1.0: USB hub found
377[ 3.020108] hub 1-1:1.0: 4 ports detected
378[ 3.283210] systemd[1]: System time before build time, advancing clock.
379[ 3.336140] usb 1-1.2: new high-speed USB device number 3 using ehci-platform
380[ 3.389577] NET: Registered protocol family 10
381[ 3.426774] Segment Routing with IPv6
382[ 3.447871] systemd[1]: systemd 239 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
383[ 3.468657] systemd[1]: Detected architecture arm.
384
385Welcome to ST OpenSTLinux - Weston - (A Yocto Project Based Distro) 2.6-snapshot-20190903 (thud)!
386
387[ 3.527427] systemd[1]: Set hostname to <stm32mp1>.
388[ 3.540188] systemd[1]: Hardware watchdog 'STM32 Independent Watchdog', version 0
389[ 3.547451] systemd[1]: Set hardware watchdog to 30s.
390[ 3.876250] usb 1-1.3: new low-speed USB device number 4 using ehci-platform
391[ 4.058754] input: USB Keyboard as /devices/platform/soc/5800d000.usbh-ehci/usb1/1-1/1-1.3/1-1.3:1.0/0003:04D9:1603.0001/input/input1
392[ 4.136955] hid-generic 0003:04D9:1603.0001: input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-5800d000.usbh-ehci-1.3/input0
393[ 4.166591] input: USB Keyboard System Control as /devices/platform/soc/5800d000.usbh-ehci/usb1/1-1/1-1.3/1-1.3:1.1/0003:04D9:1603.0002/input/input2
394[ 4.246797] input: USB Keyboard Consumer Control as /devices/platform/soc/5800d000.usbh-ehci/usb1/1-1/1-1.3/1-1.3:1.1/0003:04D9:1603.0002/input/input3
395[ 4.259621] hid-generic 0003:04D9:1603.0002: input: USB HID v1.10 Device [ USB Keyboard] on usb-5800d000.usbh-ehci-1.3/input1
396[ 4.278101] systemd[1]: Unnecessary job for dev-ttySTM0.device was removed.
397[ 4.285825] random: systemd: uninitialized urandom read (16 bytes read)
398[ 4.294382] systemd[1]: Created slice User and Session Slice.
399[ OK ] Created slice User and Session Slice.
400[ 4.326327] random: systemd: uninitialized urandom read (16 bytes read)
401[ 4.332022] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
402[ OK ] Started Forward Password Requests to Wall Directory Watch.
403[ 4.376048] usb 1-1.4: new full-speed USB device number 5 using ehci-platform
404[ 4.376633] random: systemd: uninitialized urandom read (16 bytes read)
405[ 4.389276] systemd[1]: Listening on Network Service Netlink Socket.
406[ OK ] Listening on Network Service Netlink Socket.
407[ 4.429883] systemd[1]: Created slice system-getty.slice.
408[ OK ] Created slice system-getty.slice.
409[ OK ] Started Dispatch Password Requests to Console Directory Watch.
410[ OK ] Listening on udev Kernel Socket.
411[ OK ] Listening on initctl Compatibility Named Pipe.
412[ 4.551159] input: Fujitsu Mouse Fujitsu Mouse Mouse as /devices/platform/soc/5800d000.usbh-ehci/usb1/1-1/1-1.4/1-1.4:1.0/0003:1A81:2205.0003/input/input4
413[ 4.564303] input: Fujitsu Mouse Fujitsu Mouse as /devices/platform/soc/5800d000.usbh-ehci/usb1/1-1/1-1.4/1-1.4:1.0/0003:1A81:2205.0003/input/input5
414[ 4.577696] input: Fujitsu Mouse Fujitsu Mouse Consumer Control as /devices/platform/soc/5800d000.usbh-ehci/usb1/1-1/1-1.4/1-1.4:1.0/0003:1A81:2205.0003/input/input6
415[ OK ] Created slice system-serial\x2dgetty.slice.
416[ 4.656782] input: Fujitsu Mouse Fujitsu Mouse System Control as /devices/platform/soc/5800d000.usbh-ehci/usb1/1-1/1-1.4/1-1.4:1.0/0003:1A81:2205.0003/input/input7
417[ 4.670582] hid-generic 0003:1A81:2205.0003: input: USB HID v1.11 Mouse [Fujitsu Mouse Fujitsu Mouse] on usb-5800d000.usbh-ehci-1.4/input0
418[ OK ] Listening on Process Core Dump Socket.
419[ OK ] Listening on Journal Socket (/dev/log).
420[ OK ] Listening on udev Control Socket.
421[ OK ] Listening on Journal Socket.
422 Starting udev Coldplug all Devices...
423 Starting Mount partitions...
424 Starting Remount Root and Kernel File Systems...
425 Mounting Kernel Debug File System...
426[ OK ] Reached target Swap.
427 Mounting Temporary Directory (/tmp)...
428[ OK ] Reached target Slices.
429[ 5.019294] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
430[ OK ] Listening on Syslog Socket.
431[ OK ] Started Hardware RNG Entropy Gatherer Daemon.
432[ 5.075369] random: crng init done
433[ 5.079832] random: 7 urandom warning(s) missed due to ratelimiting
434 Starting Load Kernel Modules...
435 Starting Create list of required st…ce nodes for the current kernel...
436 Starting Journal Service...
437[ OK ] Reached target Remote File Systems.
438 Mounting POSIX Message Queue File System...
439[ OK ] Reached target Paths.
440[ 5.384426] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
441[ OK ] Started Remount Root and Kernel File Systems.
442[ OK ] Mounted Kernel Debug File System.
443[ OK ] Mounted Temporary Directory (/tmp).
444[ OK ] Started Load Kernel Modules.
445[ OK ] Started Create list of required sta…vice nodes for the current kernel.
446[ OK ] Mounted POSIX Message Queue File System.
447 Mounting FUSE Control File System...
448 Starting Apply Kernel Variables...
449 Mounting Kernel Configuration File System...
450 Starting Create Static Device Nodes in /dev...
451[ OK ] Started Starts Psplash Boot screen.
452[ OK ] Mounted FUSE Control File System.
453[ OK ] Started Journal Service.
454[ OK ] Started Apply Kernel Variables.
455[ OK ] Mounted Kernel Configuration File System.
456[ OK ] Started Create Static Device Nodes in /dev.
457[ OK ] Reached target Local File Systems (Pre).
458[ 6.005783] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null)
459 Mounting /var/volatile...
460[ OK ] Reached target Containers.
461 Starting udev Kernel Device Manager...
462 Starting Flush Journal to Persistent Storage...
463[ OK ] Mounted /var/volatile.
464 Starting Load/Save Random Seed...
465[ OK ] Started udev Kernel Device Manager.
466[ 6.438580] systemd-journald[157]: Received request to flush runtime journal from PID 1
467[ 6.535874] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
468[ OK ] Started Flush Journal to Persistent Storage.
469[ OK ] Started Mount partitions.
470[ OK ] Started Load/Save Random Seed.
471[ OK ] Reached target Local File Systems.
472 Starting Create Volatile Files and Directories...
473[ OK ] Started Create Volatile Files and Directories.
474 Starting Update UTMP about System Boot/Shutdown...
475 Starting Network Time Synchronization...
476[ OK ] Started Update UTMP about System Boot/Shutdown.
477[ OK ] Started Network Time Synchronization.
478[ OK ] Reached target System Time Synchronized.
479[ 7.882880] input: generic ft5x06 (11) as /devices/platform/soc/40012000.i2c/i2c-0/0-0038/input/input10
480[ OK ] Started udev Coldplug all Devices.
481[ OK ] Reached target System Initialization.
482[ OK ] Listening on D-Bus System Message B[ 7.963677] Bluetooth: Core ver 2.22
483us[ 7.967461] NET: Registered protocol family 31
484[ 7.971885] Bluetooth: HCI device and connection manager initialized
485 Socket.
486[ 7.996257] Bluetooth: HCI socket layer initialized
487[ 7.999715] Bluetooth: L2CAP socket layer initialized
488[ 8.019297] Bluetooth: SCO socket layer initialized
489[ OK ] Started Daily Cleanup of Temporary Directories.
490[ OK ] Listening on RPCbind Server Activatio[ 8.047635] Bluetooth: HCI UART driver ver 2.3
491n Socket.
492[ 8.055949] Bluetooth: HCI UART protocol H4 registered
493[ 8.065136] Bluetooth: HCI UART protocol Broadcom registered
494[ 8.065954] hci_uart_bcm serial0-0: No reset resource, using default baud rate
495 Starting Console System Startup Logging...
496[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
497[ 8.261980] galcore: loading out-of-tree module taints kernel.
498[ 8.334637] Galcore version 6.2.4.174315
499[ OK ] Listening on dropbear.socket.
500[ OK ] Reached target Sockets.
501[ OK ] Reached target Basic System.
502[ 8.467405] cfg80211: Loading compiled-in X.509 certificates for regulatory database
503[ 8.549498] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
504[ OK ] Started System Logging Service.
505[ OK ] Started Kernel Logging Service.
506 Starting Login Service...
507 Starting Netdata, Real-time performance monitoring...
508[ 9.180390] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1
509 Starting Weston Wayland Compositor...
510[ OK ] Started ST Verify if eth0 network interface are already configured.
511 Starting Network Service...
512[ 9.412393] media: Linux media interface: v0.10
513[ 9.447846] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1
514[ OK ] Started TEE Supplicant.
515[ 9.552654] videodev: Linux video capture interface: v2.00
516 Starting Enable USB Ethernet gadget...
517[ 9.596641] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43430/1 wl0: Sep 11 2018 09:22:09 version 7.45.98.65 (r707797 CY) FWID 01-b54727f
518[ 9.627276] usbcore: registered new interface driver snd-usb-audio
519[ OK ] Started D-Bus System Message Bus.
520[ 9.744864] uvcvideo: Found UVC 1.00 device <unnamed> (046d:0823)
521[ 9.822933] uvcvideo 1-1.2:1.2: Entity type for entity Extension 4 was not initialized!
522[ 9.860561] uvcvideo 1-1.2:1.2: Entity type for entity Processing 2 was not initialized!
523[ 9.928378] uvcvideo 1-1.2:1.2: Entity type for entity Camera 1 was not initialized!
524[ 9.934718] uvcvideo 1-1.2:1.2: Entity type for entity Extension 5 was not initialized!
525 Starting Sound Service...
526[ 10.013382] uvcvideo 1-1.2:1.2: Entity type for entity Extension 6 was not initialized!
527[ 10.048625] uvcvideo 1-1.2:1.2: Entity type for entity Extension 7 was not initialized!
528[ 10.085931] uvcvideo 1-1.2:1.2: Entity type for entity Extension 8 was not initialized!
529[ 10.092450] input: UVC Camera (046d:0823) as /devices/platform/soc/5800d000.usbh-ehci/usb1/1-1/1-1.2/1-1.2:1.2/input/input11
530[ 10.098403] usbcore: registered new interface driver uvcvideo
531[ 10.098413] USB Video Class driver (1.1.1)
532[[ 10.120793] using random self ethernet address
533[ 10.120808] using random host ethernet address
534[ 10.156216] Bluetooth: hci0: command 0xfc18 tx timeout
535 OK ] Started Console System Startup Logging.
536[ 10.460545] usb0: HOST MAC da:7b:f1:0c:99:3c
537[ 10.467234] usb0: MAC 42:ab:ea:e7:04:f0
538[ 10.474387] dwc2 49000000.usb-otg: bound driver configfs-gadget
539[ 10.710474] dwc2 49000000.usb-otg: new device is high-speed
540[ 10.800671] dwc2 49000000.usb-otg: new device is high-speed
541[ 10.887964] dwc2 49000000.usb-otg: new address 13
542[ 10.913580] configfs-gadget gadget: high-speed config #1: c
543[ 11.212707] Generic PHY stmmac-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
544[ OK ] Started Network Service.
545[ 11.308879] dwmac4: Master AXI performs any burst length
546[ 11.312842] stm32-dwmac 5800a000.ethernet eth0: No Safety Features support found
547[ 11.344754] stm32-dwmac 5800a000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
548[ 11.387420] stm32-dwmac 5800a000.ethernet eth0: registered PTP clock
549[ 11.411450] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
550[ 11.446568] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
551[ 11.476156] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready
552[ OK ] Started Enable USB Ethernet gadget.
553[ 11.903009] Gcnano is present and activated
554[ OK ] Started Netdata, Real-time performance monitoring.
555[ OK ] Started Weston Wayland Compositor.
556[ 12.397182] stm32-dwmac 5800a000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
557[ 12.404313] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
558[ OK ] Started Sound Service.
559[* ] A start job is running for Login Service (13s / 1min 34s)[ 18.396152] Bluetooth: hci0: BCM: failed to write update baudrate (-110)
560[ 18.401459] Bluetooth: hci0: Failed to set baudrate
561[** ] A start job is running for Login Service (14s / 1min 34s)[*** ] A start job is running for Login Service (14s / 1min 34s)[ *** ] A start job is running for Login Service (15s / 1min 34s)[ *** ] A start job is running for Login Service (15s / 1min 34s) Starting Bluetooth service...
562[ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
563 Stopping Network Service...
564 Starting Save/Restore Sound Card State...
565[ OK ] Created slice system-systemd\x2dbacklight.slice.
566 Starting Load/Save Screen Backlight…ess of backlight:5a000000.dsi.0...
567[ OK ] Stopped Network Service.
568[ OK ] Started Save/Restore Sound Card State.
569[ OK ] Started Load/Save Screen Backlight …tness of backlight:5a000000.dsi.0.
570[ OK ] Started Bluetooth service.
571 Starting Hostname Service...
572[ OK ] Reached target Bluetooth.
573 Starting Load/Save RF Kill Switch Status...
574[ OK ] Reached target Sound Card.
575[ 20.476147] Bluetooth: hci0: command 0x0c03 tx timeout
576 Starting Network Service...
577[ OK ] Started Load/Save RF Kill Switch Status.
578[ OK ] Started Login Service.
579[ OK ] Started Network Service.
580 Starting Network Name Resolution...
581 Starting Wait for Network to be Configured...
582[ OK ] Started Hostname Service.
583[ OK ] Started Network Name Resolution.
584 Starting Avahi mDNS/DNS-SD Stack...
585[ OK ] Reached target Host and Network Name Lookups.
586[ OK ] Reached target Network.
587 Starting Target Communication Framework agent...
588 Starting Permit User Sessions...
589[ OK ] Started IIO Daemon.
590[ OK ] Started Permit User Sessions.
591[ OK ] Started Avahi mDNS/DNS-SD Stack.
592[ OK ] Started Serial Getty on ttySTM0.
593[ OK ] Started Getty on tty1.
594[ OK ] Reached target Login Prompts.
595[ OK ] Started Target Communication Framework agent.
596[ OK ] Reached target Multi-User System.
597 Starting Update UTMP about System Runlevel Changes...
598[ OK ] Started Update UTMP about System Runlevel Changes.
599[ 26.166266] usb 1-1.2: reset high-speed USB device number 3 using ehci-platform
600
601ST OpenSTLinux - Weston - (A Yocto Project Based Distro) 2.6-snapshot stm32mp1 ttySTM0
602
603stm32mp1 login: root (automatic login)
604
605[ 28.636181] Bluetooth: hci0: BCM: Reset failed (-110)
606root@stm32mp1:~#