· 6 years ago · Nov 14, 2019, 03:38 PM
1�a����xP " HELLO! BOOT0 is starting!
2boot0 commit : 045061a8bb2580cb3fa02e301f52a015040c158f
3
4boot0 version : 4.0.0
5set pll start
6set pll end
7rtc[0] value = 0x00000000
8rtc[1] value = 0x00000000
9rtc[2] value = 0x00000000
10rtc[3] value = 0x00000000
11rtc[4] value = 0x00000000
12rtc[5] value = 0x00000000
13DRAM driver version: V1.1
14rsb_send_initseq: rsb clk 400Khz -> 3Mhz
15PMU: AXP81X
16ddr voltage = 1500 mv
17DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
18DRAM clk = 672 MHz
19DRAM zq value: 003b3bdd
20DRAM single rank full DQ OK
21DRAM size = 1024 MB
22DRAM init ok
23dram size =1024
24card boot number = 0, boot0 copy = 0
25card no is 0
26sdcard 0 line count 4
27[mmc]: mmc driver ver 2015-05-08 20:06
28[mmc]: sdc0 spd mode error, 2
29[mmc]: Wrong media type 0x00000000
30[mmc]: ***Try SD card 0***
31[mmc]: HSSDR52/SDR25 4 bit
32[mmc]: 50000000 Hz
33[mmc]: 15193 MB
34[mmc]: ***SD/MMC 0 init OK!!!***
35sdcard 0 init ok
36The size of uboot is 000f8000.
37sum=f4287e29
38src_sum=f4287e29
39Succeed in loading uboot from sdmmc flash.
40boot0: start load other image
41boot0: Loading BL3-1
42Loading file 0 at address 0x40000000,size 0x0000a400 success
43boot0: Loading scp
44Loading file 2 at address 0x00040000,size 0x00019c00 success
45set arisc reset to de-assert state
46Ready to disable icache.
47 � Configuring SPC Controller
48NOTICE: BL3-1: v1.0(debug):864ef11
49NOTICE: BL3-1: Built : 21:59:22, May 8 2017
50INFO: BL3-1: Initializing runtime services
51INFO: BL3-1: Preparing for EL3 exit to normal world
52INFO: BL3-1: Next image address = 0x4a000000
53INFO: BL3-1: Next image spsr = 0x1d3
54
55
56U-Boot 2014.07-00014-gc616876 (May 30 2017 - 18:44:41) Allwinner Technology
57
58uboot commit : c616876a3e07117d9bf1a5fdadbc7e7c233c4f34
59
60rsb: secure monitor exist
61[ 0.406]pmbus: ready
62[ 0.409][ARISC] :arisc initialize
63[ 0.848][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table
64[SCP] :sunxi-arisc driver begin startup 2
65[SCP] :arisc_para size:1a8
66[SCP] :arisc version: [v0.1.76]
67[SCP] :sunxi-arisc driver v1.10 is starting
68[ 1.013][ARISC] :sunxi-arisc driver startup succeeded
69[ 1.058]PMU: AXP81X
70[ 1.060]PMU: AXP81X found
71bat_vol=123, ratio=100
72[ 1.067]PMU: dcdc2 1100
73[ 1.070]PMU: cpux 1008 Mhz,AXI=336 Mhz
74PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz
75device_type = 3253, onoff=1
76dcdc1_vol = 3300, onoff=1
77dcdc2_vol = 1100, onoff=1
78dcdc6_vol = 1100, onoff=1
79aldo1_vol = 2800, onoff=0
80aldo2_vol = 1800, onoff=1
81aldo3_vol = 3000, onoff=1
82dldo1_vol = 3300, onoff=0
83dldo2_vol = 3300, onoff=0
84dldo3_vol = 2800, onoff=0
85dldo4_vol = 3300, onoff=1
86eldo1_vol = 1800, onoff=1
87eldo2_vol = 1800, onoff=0
88eldo3_vol = 1800, onoff=0
89fldo1_vol = 1200, onoff=0
90fldo2_vol = 1100, onoff=1
91gpio0_vol = 3100, onoff=0
92vbus not exist
93no battery, limit to dc
94run key detect
95no key found
96no uart input
97DRAM: 1008 MiB
98fdt addr: 0x76eba000
99Relocation Offset is: 35f0c000
100In: serial
101Out: serial
102Err: serial
103gic: sec monitor mode
104[ 1.912]start
105drv_disp_init
106init_clocks: finish init_clocks.
107fdt_get_one_gpio lcd0.lcd_gpio_1 fail
108fdt_get_one_gpio lcd0.lcd_gpio_2 fail
109fdt_get_one_gpio lcd0.lcd_gpio_3 fail
110fdt_get_one_gpio lcd0.lcd_gpio_scl fail
111fdt_get_one_gpio lcd0.lcd_gpio_sda fail
112pwm_request:pwm number = 1
113pwm_request: reg = 0x1f03800.pchip->pwm = 16
114reg_busy_offset=0, reg_busy_shift = 0, reg_enable_offset = 0
115request pwm success, pwm = 16!
116sunxi_pwm_config: reg_shift = 0, reg_width = 4, prescale temp = f, pres=15
117PWM _TEST: duty_ns=3906, period_ns=20000, freq=50000, per_scal=0, period_reg=0x1df005e
118enable power vcc-hdmi-33, ret=0
119drv_disp_init finish
120boot_disp.output_disp=0
121boot_disp.output_type=3
122boot_disp.output_mode=5
123fetch script data boot_disp.auto_hpd fail
124disp0 device type(4) enable
125attched ok, mgr0<-->device1, type=4, mode=5
126[ 2.953]end
127workmode = 0,storage type = 1
128[ 2.957]MMC: 0
129[mmc]: mmc driver ver 2015-06-03 13:50:00
130SUNXI SD/MMC: 0
131[mmc]: start mmc_calibrate_delay_unit, don't access device...
132[mmc]: delay chain cal done, sample: 200(ps)
133[mmc]: media type 0x0
134[mmc]: Wrong media type 0x0
135[mmc]: ************Try SD card 0************
136[mmc]: host caps: 0x27
137[mmc]: MID 03 PSN 01132d3b
138[mmc]: PNM SL16G -- 0x53-4c-31-36-47
139[mmc]: PRV 8.0
140[mmc]: MDT m-3 y-2015
141[mmc]: speed mode : HSSDR52/SDR25
142[mmc]: clock : 50000000 Hz
143[mmc]: bus_width : 4 bit
144[mmc]: user capacity : 15193 MB
145[mmc]: ************SD/MMC 0 init OK!!!************
146[mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte
147[mmc]: secure_feature : 0x0
148[mmc]: secure_removal_type : 0x0
149[ 3.276]sunxi flash init ok
150[mmc]: Has init
151[ 3.345]---drivers/mmc/mmc.c 2733 mmc_init
152reading uboot.env
153
154** Unable to read "uboot.env" from mmc0:1 **
155Using default environment
156
157--------fastboot partitions--------
158mbr not exist
159base bootcmd=run mmcbootcmd
160bootcmd set setargs_mmc
161key 0
162recovery key high 12, low 10
163fastboot key high 6, low 4
164no misc partition is found
165to be run cmd=run mmcbootcmd
166update dtb dram start
167update dtb dram end
168serial is: 841051900800580804cb
169check for ANX9807
170get Pine64 model from DRAM size
171DRAM >512M
172Pine64 model: pine64-plus
173no battery exist
174sunxi_bmp_logo_display
175[mmc]: Has init
176[ 3.742]---drivers/mmc/mmc.c 2733 mmc_init
177reading bootlogo.bmp
178** Unable to read file bootlogo.bmp **
179sunxi bmp info error : unable to open logo file bootlogo.bmp
180[ 3.759]inter uboot shell
181autoboot in 1 seconds, Press s to abort
182[mmc]: Has init
183[ 4.940]---drivers/mmc/mmc.c 2733 mmc_init
184reading uEnv.txt
185** Unable to read file uEnv.txt **
186[mmc]: Has init
187[ 4.953]---drivers/mmc/mmc.c 2733 mmc_init
188reading boot.scr
1891063 bytes read in 3 ms (345.7 KiB/s)
190Booting with script ...
191## Executing script at 41000000
192[mmc]: Has init
193[ 4.978]---drivers/mmc/mmc.c 2733 mmc_init
19426153472 bytes read in 1386 ms (18 MiB/s)
195[mmc]: Has init
196[ 6.377]---drivers/mmc/mmc.c 2733 mmc_init
197690136 bytes read in 45 ms (14.6 MiB/s)
198[mmc]: Has init
199[ 6.434]---drivers/mmc/mmc.c 2733 mmc_init
20023466 bytes read in 61 ms (375 KiB/s)
201## Booting kernel from Legacy Image at 42000000 ...
202 Image Name:
203 Image Type: ARM Linux Kernel Image (uncompressed)
204 Data Size: 690072 Bytes = 673.9 KiB
205 Load Address: 40200000
206 Entry Point: 40200000
207 Verifying Checksum ... OK
208## Flattened Device Tree blob at 58000000
209 Booting using the fdt blob at 0x58000000
210 Loading Kernel Image ... OK
211 reserving fdt memory region: addr=58000000 size=6000
212 Loading Device Tree to 44ff6000, end 44ffefff ... OK
213
214Starting kernel ...
215
216[mmc]: MMC Device 2 not found
217[mmc]: mmc 2 not find, so not exit
218INFO: BL3-1: Next image address = 0x40200000
219INFO: BL3-1: Next image spsr = 0x3c9
220(XEN) Xen version 4.6.5 (Ubuntu 4.6.5-0ubuntu1.4) (stefan.bader@canonical.com) (gcc (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) 5.4.0 20160609) debug=n Fri Oct 13 15:45:11 UTC 2017
221(XEN) Processor: 410fd034: "ARM Limited", variant: 0x0, part 0xd03, rev 0x4
222(XEN) 64-bit Execution:
223(XEN) Processor Features: 0000000000002222 0000000000000000
224(XEN) Exception Levels: EL3:64+32 EL2:64+32 EL1:64+32 EL0:64+32
225(XEN) Extensions: FloatingPoint AdvancedSIMD
226(XEN) Debug Features: 0000000010305106 0000000000000000
227(XEN) Auxiliary Features: 0000000000000000 0000000000000000
228(XEN) Memory Model Features: 0000000000001122 0000000000000000
229(XEN) ISA Features: 0000000000011120 0000000000000000
230(XEN) 32-bit Execution:
231(XEN) Processor Features: 00000131:00011011
232(XEN) Instruction Sets: AArch32 A32 Thumb Thumb-2 Jazelle
233(XEN) Extensions: GenericTimer Security
234(XEN) Debug Features: 03010066
235(XEN) Auxiliary Features: 00000000
236(XEN) Memory Model Features: 10201105 40000000 01260000 02102211
237(XEN) ISA Features: 02101110 13112111 21232042 01112131 00011142 00011121
238(XEN) Generic Timer IRQ: phys=30 hyp=26 virt=27 Freq: 24000 KHz
239(XEN) GICv2 initialization:
240(XEN) gic_dist_addr=0000000001c81000
241(XEN) gic_cpu_addr=0000000001c82000
242(XEN) gic_hyp_addr=0000000001c84000
243(XEN) gic_vcpu_addr=0000000001c86000
244(XEN) gic_maintenance_irq=25
245(XEN) GICv2: 224 lines, 4 cpus, secure (IID 0200143b).
246(XEN) Using scheduler: SMP Credit Scheduler (credit)
247(XEN) Allocated console ring of 16 KiB.
248(XEN) Bringing up CPU1
249(XEN) Bringing up CPU2
250(XEN) Bringing up CPU3
251(XEN) Brought up 4 CPUs
252(XEN) P2M: 40-bit IPA with 40-bit PA
253(XEN) P2M: 3 levels with order-1 root, VTCR 0x80023558
254(XEN) I/O virtualisation disabled
255(XEN) *** LOADING DOMAIN 0 ***
256(XEN) Loading kernel from boot module @ 0000000052000000
257(XEN) Allocating 1:1 mappings totalling 256MB for dom0:
258(XEN) BANK[0] 0x00000060000000-0x00000070000000 (256MB)
259(XEN) Grant table range: 0x0000007fe00000-0x0000007fe51000
260(XEN) Loading zImage from 0000000052000000 to 0000000060080000-0000000061971200
261(XEN) Allocating PPI 16 for event channel interrupt
262(XEN) Loading dom0 DTB to 0x0000000068000000-0x0000000068005a67
263(XEN) Scrubbing Free RAM on 1 nodes using 4 CPUs
264(XEN) ..done.
265(XEN) Initial low memory virq threshold set at 0x4000 pages.
266(XEN) Std. Loglevel: Errors and warnings
267(XEN) Guest Loglevel: Nothing (Rate-limited: Errors and warnings)
268(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
269(XEN) Freed 276kB init memory.
270(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER4
271(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER8
272(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER12
273(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER16
274(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER20
275(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER24
276(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER0
277[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
278[ 0.000000] Linux version 5.4.0-rc3 (janani@janani-Vostro-2520) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #2 SMP PREEMPT Fri Nov 1 13:01:35 IST 2019
279[ 0.000000] Machine model: Pine64+
280[ 0.000000] printk: debug: ignoring loglevel setting.
281[ 0.000000] Xen 4.6 support found
282[ 0.000000] efi: Getting EFI parameters from FDT:
283[ 0.000000] efi: UEFI not found.
284[ 0.000000] cma: Reserved 32 MiB at 0x000000006e000000
285[ 0.000000] NUMA: No NUMA configuration found
286[ 0.000000] NUMA: Faking a node at [mem 0x0000000060000000-0x000000006fffffff]
287[ 0.000000] NUMA: NODE_DATA [mem 0x6df5e800-0x6df5ffff]
288[ 0.000000] Zone ranges:
289[ 0.000000] DMA32 [mem 0x0000000060000000-0x000000006fffffff]
290[ 0.000000] Normal empty
291[ 0.000000] Movable zone start for each node
292[ 0.000000] Early memory node ranges
293[ 0.000000] node 0: [mem 0x0000000060000000-0x000000006fffffff]
294[ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000006fffffff]
295[ 0.000000] On node 0 totalpages: 65536
296[ 0.000000] DMA32 zone: 1024 pages used for memmap
297[ 0.000000] DMA32 zone: 0 pages reserved
298[ 0.000000] DMA32 zone: 65536 pages, LIFO batch:15
299[ 0.000000] psci: probing for conduit method from DT.
300[ 0.000000] psci: PSCIv0.2 detected in firmware.
301[ 0.000000] psci: Using standard PSCI v0.2 function IDs
302[ 0.000000] psci: Trusted OS migration not required
303[ 0.000000] percpu: Embedded 22 pages/cpu s52952 r8192 d28968 u90112
304[ 0.000000] pcpu-alloc: s52952 r8192 d28968 u90112 alloc=22*4096
305[ 0.000000] pcpu-alloc: [0] 0 [0] 1
306[ 0.000000] Detected VIPT I-cache on CPU0
307[ 0.000000] CPU features: detected: ARM erratum 845719
308[ 0.000000] CPU features: detected: ARM erratum 843419
309[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64512
310[ 0.000000] Policy zone: DMA32
311[ 0.000000] Kernel command line: console=hvc0 earlyprintk=xen ignore_loglevel clk_ignore_unused root=/dev/mmcblk0p2 rw rootwait panic=10
312[ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
313[ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
314[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
315[ 0.000000] Memory: 185740K/262144K available (12156K kernel code, 1860K rwdata, 6420K rodata, 5056K init, 452K bss, 43636K reserved, 32768K cma-reserved)
316[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
317[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
318[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2.
319[ 0.000000] Tasks RCU enabled.
320[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
321[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
322[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
323[ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x458 with crng_init=0
324[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
325[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
326[ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
327[ 0.000675] Console: colour dummy device 80x25
328[ 0.001333] printk: console [hvc0] enabled
329[ 0.001411] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
330[ 0.001441] pid_max: default: 32768 minimum: 301
331[ 0.001535] LSM: Security Framework initializing
332[ 0.001605] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
333[ 0.001628] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
334[ 0.024078] ASID allocator initialised with 32768 entries
335[ 0.024464] xen:grant_table: Grant tables using version 1 layout
336[ 0.024500] Grant table initialized
337[ 0.024534] xen:events: Using FIFO-based ABI
338[ 0.024584] Xen: initializing cpu0
339[ 0.032090] rcu: Hierarchical SRCU implementation.
340[ 0.041674] EFI services will not be available.
341[ 0.048156] smp: Bringing up secondary CPUs ...
342(XEN) d0v1: vGICD: unhandled word write 0xffffffff to ICACTIVER0
343[ 0.080375] Detected VIPT I-cache on CPU1
344[ 0.080476] Xen: initializing cpu1
345[ 0.080500] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
346[ 0.080632] smp: Brought up 1 node, 2 CPUs
347[ 0.080679] SMP: Total of 2 processors activated.
348[ 0.080696] CPU features: detected: 32-bit EL0 Support
349[ 0.080713] CPU features: detected: CRC32 instructions
350[ 0.086597] CPU: All CPU(s) started at EL1
351[ 0.086641] alternatives: patching kernel code
352[ 0.087763] devtmpfs: initialized
353[ 0.093209] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
354[ 0.093254] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
355[ 0.094445] pinctrl core: initialized pinctrl subsystem
356[ 0.095708] DMI not present or invalid.
357[ 0.096097] NET: Registered protocol family 16
358[ 0.101358] DMA: preallocated 256 KiB pool for atomic allocations
359[ 0.101394] audit: initializing netlink subsys (disabled)
360[ 0.101563] audit: type=2000 audit(0.100:1): state=initialized audit_enabled=0 res=1
361[ 0.103304] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
362[ 0.103495] xen:swiotlb_xen: Warning: only able to allocate 4 MB for software IO TLB
363[ 0.104787] software IO TLB: mapped [mem 0x6c000000-0x6c400000] (4MB)
364[ 0.106041] Serial: AMBA PL011 UART driver
365[ 0.123539] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
366[ 0.123572] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
367[ 0.123590] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
368[ 0.123609] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
369[ 0.126364] cryptd: max_cpu_qlen set to 1000
370[ 0.131182] ACPI: Interpreter disabled.
371[ 0.131860] xen:balloon: Initialising balloon driver
372[ 0.132468] iommu: Default domain type: Translated
373[ 0.132743] vgaarb: loaded
374[ 0.133069] SCSI subsystem initialized
375[ 0.133277] libata version 3.00 loaded.
376[ 0.133514] usbcore: registered new interface driver usbfs
377[ 0.133569] usbcore: registered new interface driver hub
378[ 0.133620] usbcore: registered new device driver usb
379[ 0.134225] pps_core: LinuxPPS API ver. 1 registered
380[ 0.134242] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
381[ 0.134274] PTP clock support registered
382[ 0.134393] EDAC MC: Ver: 3.0.0
383[ 0.135437] FPGA manager framework
384[ 0.135529] Advanced Linux Sound Architecture Driver Initialized.
385[ 0.136360] clocksource: Switched to clocksource arch_sys_counter
386[ 0.136527] VFS: Disk quotas dquot_6.6.0
387[ 0.136592] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
388[ 0.136835] pnp: PnP ACPI: disabled
389[ 0.144251] thermal_sys: Registered thermal governor 'step_wise'
390[ 0.144255] thermal_sys: Registered thermal governor 'power_allocator'
391[ 0.144883] NET: Registered protocol family 2
392[ 0.145290] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
393[ 0.145325] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
394[ 0.145366] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)
395[ 0.145417] TCP: Hash tables configured (established 2048 bind 2048)
396[ 0.145500] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
397[ 0.145537] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
398[ 0.145656] NET: Registered protocol family 1
399[ 0.146197] RPC: Registered named UNIX socket transport module.
400[ 0.146218] RPC: Registered udp transport module.
401[ 0.146232] RPC: Registered tcp transport module.
402[ 0.146246] RPC: Registered tcp NFSv4.1 backchannel transport module.
403[ 0.146270] PCI: CLS 0 bytes, default 64
404[ 0.147002] hw perfevents: failed to parse interrupt-affinity[0] for pmu
405[ 0.147025] hw perfevents: /pmu: failed to register PMU devices!
406[ 0.147058] armv8-pmu: probe of pmu failed with error -22
407[ 0.147253] kvm [1]: HYP mode not available
408[ 0.155793] Initialise system trusted keyrings
409[ 0.155999] workingset: timestamp_bits=44 max_order=16 bucket_order=0
410[ 0.163002] squashfs: version 4.0 (2009/01/31) Phillip Lougher
411[ 0.163821] NFS: Registering the id_resolver key type
412[ 0.163859] Key type id_resolver registered
413[ 0.163872] Key type id_legacy registered
414[ 0.163892] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
415[ 0.164098] 9p: Installing v9fs 9p2000 file system support
416[ 0.179997] Key type asymmetric registered
417[ 0.180018] Asymmetric key parser 'x509' registered
418[ 0.180070] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
419[ 0.180093] io scheduler mq-deadline registered
420[ 0.180108] io scheduler kyber registered
421[ 0.181715] sun50i-de2-bus 1000000.bus: Error couldn't map SRAM to device
422[ 0.182453] sun4i-usb-phy 1c19400.phy: failed to get clock usb0_phy
423[ 0.188170] sun50i-a64-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
424[ 0.191707] EINJ: ACPI disabled.
425[ 0.200733] xen:xen_evtchn: Event-channel device installed
426[ 0.206985] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
427[ 0.209400] SuperH (H)SCI(F) driver initialized
428[ 0.209911] msm_serial: driver initialized
429[ 0.211124] cacheinfo: Unable to detect cache hierarchy for CPU 0
430[ 0.217821] loop: module loaded
431[ 0.217922] Invalid max_queues (4), will use default max: 2.
432[ 0.222131] libphy: Fixed MDIO Bus: probed
433[ 0.222443] tun: Universal TUN/TAP device driver, 1.6
434[ 0.223240] thunder_xcv, ver 1.0
435[ 0.223292] thunder_bgx, ver 1.0
436[ 0.223341] nicpf, ver 1.0
437[ 0.223886] hclge is initializing
438[ 0.223902] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
439[ 0.223921] hns3: Copyright (c) 2017 Huawei Corporation.
440[ 0.223984] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
441[ 0.224000] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
442[ 0.224050] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k
443[ 0.224068] igb: Copyright (c) 2007-2014 Intel Corporation.
444[ 0.224120] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
445[ 0.224140] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
446[ 0.224487] sky2: driver version 1.30
447[ 0.224985] xen_netfront: Initialising Xen virtual ethernet driver
448[ 0.225218] VFIO - User Level meta-driver version: 0.3
449[ 0.226750] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
450[ 0.226774] ehci-pci: EHCI PCI platform driver
451[ 0.226817] ehci-platform: EHCI generic platform driver
452[ 0.227049] ehci-platform 1c1a000.usb: EHCI Host Controller
453[ 0.227084] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
454[ 0.227228] ehci-platform 1c1a000.usb: irq 16, io mem 0x01c1a000
455[ 0.240379] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
456[ 0.240997] hub 1-0:1.0: USB hub found
457[ 0.241035] hub 1-0:1.0: 1 port detected
458[ 0.241582] ehci-orion: EHCI orion driver
459[ 0.241755] ehci-exynos: EHCI EXYNOS driver
460[ 0.241849] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
461[ 0.241886] ohci-pci: OHCI PCI platform driver
462[ 0.241955] ohci-platform: OHCI generic platform driver
463[ 0.242107] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
464[ 0.242139] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
465[ 0.242277] ohci-platform 1c1a400.usb: irq 17, io mem 0x01c1a400
466[ 0.304921] hub 2-0:1.0: USB hub found
467[ 0.304958] hub 2-0:1.0: 1 port detected
468[ 0.305474] ohci-exynos: OHCI EXYNOS driver
469[ 0.306061] usbcore: registered new interface driver usb-storage
470[ 0.309090] sun6i-rtc 1f00000.rtc: registered as rtc0
471[ 0.309115] sun6i-rtc 1f00000.rtc: RTC enabled
472[ 0.309381] i2c /dev entries driver
473[ 0.313792] sdhci: Secure Digital Host Controller Interface driver
474[ 0.313813] sdhci: Copyright(c) Pierre Ossman
475[ 0.314187] Synopsys Designware Multimedia Card Interface Driver
476[ 0.315090] sdhci-pltfm: SDHCI platform and OF driver helper
477[ 0.316489] ledtrig-cpu: registered to indicate activity on CPUs
478[ 0.317679] usbcore: registered new interface driver usbhid
479[ 0.317698] usbhid: USB HID core driver
480[ 0.323589] NET: Registered protocol family 17
481[ 0.323784] 9pnet: Installing 9P2000 support
482[ 0.323856] Key type dns_resolver registered
483[ 0.324317] registered taskstats version 1
484[ 0.324332] Loading compiled-in X.509 certificates
485[ 0.337774] sun50i-a64-r-pinctrl 1f02c00.pinctrl: 1f02c00.pinctrl supply vcc-pl not found, using dummy regulator
486[ 0.338005] sunxi-rsb 1f03400.rsb: RSB running at 3030303 Hz
487[ 0.338478] axp20x-rsb sunxi-rsb-3a3: AXP20x variant AXP803 found
488[ 0.348286] dcdc1: supplied by regulator-dummy
489[ 0.348763] dcdc2: supplied by regulator-dummy
490[ 0.349001] dcdc4: supplied by regulator-dummy
491[ 0.349249] dcdc5: supplied by regulator-dummy
492[ 0.349331] vcc-dram: Bringing 1500000uV into 1360000-1360000uV
493[ 0.349569] dcdc6: supplied by regulator-dummy
494[ 0.349798] dc1sw: supplied by regulator-dummy
495[ 0.349987] aldo1: supplied by regulator-dummy
496[ 0.350222] aldo2: supplied by regulator-dummy
497[ 0.350489] aldo3: supplied by regulator-dummy
498[ 0.350741] dldo1: supplied by regulator-dummy
499[ 0.350980] dldo2: supplied by regulator-dummy
500[ 0.351233] dldo3: supplied by regulator-dummy
501[ 0.351479] dldo4: supplied by regulator-dummy
502[ 0.351729] eldo1: supplied by regulator-dummy
503[ 0.351974] eldo2: supplied by regulator-dummy
504[ 0.352221] eldo3: supplied by regulator-dummy
505[ 0.352518] fldo1: supplied by regulator-dummy
506[ 0.352776] fldo2: supplied by regulator-dummy
507[ 0.353050] rtc-ldo: supplied by regulator-dummy
508[ 0.353246] ldo-io0: supplied by regulator-dummy
509[ 0.353494] ldo-io1: supplied by regulator-dummy
510[ 0.353718] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded
511[ 0.358562] sun50i-a64-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
512[ 0.359964] ehci-platform 1c1b000.usb: EHCI Host Controller
513[ 0.360005] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3
514[ 0.360141] ehci-platform 1c1b000.usb: irq 18, io mem 0x01c1b000
515[ 0.372432] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00
516[ 0.373089] hub 3-0:1.0: USB hub found
517[ 0.373127] hub 3-0:1.0: 1 port detected
518[ 0.374725] ohci-platform 1c1b400.usb: Generic Platform OHCI controller
519[ 0.374768] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 4
520[ 0.374923] ohci-platform 1c1b400.usb: irq 19, io mem 0x01c1b400
521[ 0.436946] hub 4-0:1.0: USB hub found
522[ 0.436983] hub 4-0:1.0: 1 port detected
523[ 0.438698] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
524[ 0.439388] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
525[ 0.439422] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 5
526[ 0.440042] hub 5-0:1.0: USB hub found
527[ 0.440080] hub 5-0:1.0: 1 port detected
528[ 0.441907] sun50i-a64-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-ph not found, using dummy regulator
529[ 0.444011] sun50i-a64-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pf not found, using dummy regulator
530[ 0.444745] sunxi-mmc 1c0f000.mmc: Got CD GPIO
531[ 0.470039] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
532[ 0.470504] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01T00:00:06 UTC (6)
533[ 0.470772] clk: Not disabling unused clocks
534[ 0.470793] ALSA device list:
535[ 0.470808] No soundcards found.
536[ 0.471126] Waiting for root device /dev/mmcblk0p2...
537[ 0.523320] mmc0: new high speed SDHC card at address aaaa
538[ 0.528093] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
539[ 0.534109] mmcblk0: p1 p2
540[ 0.614058] random: fast init done
541[ 0.674722] EXT4-fs (mmcblk0p2): recovery complete
542[ 0.676363] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
543[ 0.676446] VFS: Mounted root (ext4 filesystem) on device 179:2.
544[ 0.677465] devtmpfs: mounted
545[ 0.680217] Freeing unused kernel memory: 5056K
546[ 0.680328] Run /sbin/init as init process
547[ 0.931083] systemd[1]: System time before build time, advancing clock.
548[ 1.683281] NET: Registered protocol family 10
549[ 1.684172] Segment Routing with IPv6
550[ 1.710577] random: systemd: uninitialized urandom read (16 bytes read)
551[ 1.712594] random: systemd: uninitialized urandom read (16 bytes read)
552[ 1.732603] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
553[ 1.732833] systemd[1]: Detected virtualization xen.
554[ 1.732866] systemd[1]: Detected architecture arm64.
555
556Welcome to Ubuntu 16.04.6 LTS!
557
558[ 1.735085] systemd[1]: Set hostname to <LXC_NAME>.
559[ 1.751448] random: systemd: uninitialized urandom read (16 bytes read)
560[ 2.007795] systemd[1]: Listening on udev Kernel Socket.
561[ OK ] Listening on udev Kernel Socket.
562[ 2.008677] systemd[1]: Listening on udev Control Socket.
563[ OK ] Listening on udev Control Socket.
564[ 2.008959] systemd[1]: Reached target Encrypted Volumes.
565[ OK ] Reached target Encrypted Volumes.
566[ 2.009425] systemd[1]: Listening on Journal Audit Socket.
567[ OK ] Listening on Journal Audit Socket.
568[ 2.009754] systemd[1]: Listening on Syslog Socket.
569[ OK ] Listening on Syslog Socket.
570[ 2.010345] systemd[1]: Created slice User and Session Slice.
571[ OK ] Created slice User and Session Slice.
572[ OK ] Started Trigger resolvconf update for networkd DNS.
573[ OK ] Started Forward Password Requests to Wall Directory Watch.
574[ OK ] Created slice System Slice.
575[ OK ] Created slice system-serial\x2dgetty.slice.
576[ OK ] Reached target Slices.
577[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
578[ OK ] Reached target Remote File Systems (Pre).
579[ OK ] Reached target Remote File Systems.
580[ OK ] Started Dispatch Password Requests to Console Directory Watch.
581[ OK ] Reached target Paths.
582[ OK ] Reached target Swap.
583[ OK ] Listening on Journal Socket.
584 Starting Remount Root and Kernel File Systems...
585 Mounting Huge Pages File System...
586 Starting Create list of required st... nodes for the current kernel...
587 Mounting POSIX Message Queue File System...
588 Mounting Debug File System...
589 Starting Nameserver information manager...
590 Starting Set console keymap...
591 Starting Load Kernel Modules...
592[ OK ] Listening on Journal Socket (/dev/log).
593 Starting Journal Service...
594[ OK ] Started Remount Root and Kernel File Systems.
595[ OK ] Started Create list of required sta...ce nodes for the current kernel.
596[ OK ] Started Load Kernel Modules.
597[ OK ] Mounted Huge Pages File System.
598[ OK ] Mounted Debug File System.
599[ OK ] Mounted POSIX Message Queue File System.
600[ OK ] Started Nameserver information manager.
601[ OK ] Reached target Network (Pre).
602 Mounting Configuration File System...
603 Starting Apply Kernel Variables...
604 Starting Create Static Device Nodes in /dev...
605 Starting udev Coldplug all Devices...
606 Starting Load/Save Random Seed...
607[ OK ] Mounted Configuration File System.
608[ OK ] Started Journal Service.
609[ OK ] Started Apply Kernel Variables.
610[ OK ] Started Load/Save Random Seed.
611 Starting Flush Journal to Persistent Storage...
612[ OK ] Started Create Static Device Nodes in /dev.
613 Starting udev Kernel Device Manager...
614[ 2.441260] systemd-journald[188]: Received request to flush runtime journal from PID 1
615[ OK ] Started Set console keymap.
616[ OK ] Reached target Local File Systems (Pre).
617[ OK ] Reached target Local File Systems.
618 Starting Raise network interfaces...
619 Starting Set console font and keymap...
620[ OK ] Started Flush Journal to Persistent Storage.
621 Starting Create Volatile Files and Directories...
622[ OK ] Started udev Kernel Device Manager.
623 Starting LSB: QEMU KVM module loading script...
624[ OK ] Started Create Volatile Files and Directories.
625 Starting Update UTMP about System Boot/Shutdown...
626 Starting Network Time Synchronization...
627[ OK ] Started Update UTMP about System Boot/Shutdown.
628[ OK ] Started Network Time Synchronization.
629[ OK ] Started LSB: QEMU KVM module loading script.
630[ OK ] Reached target System Time Synchronized.
631[ OK ] Started udev Coldplug all Devices.
632[ OK ] Reached target System Initialization.
633[ OK ] Started Daily apt download activities.
634[ OK ] Started Daily apt upgrade and clean activities.
635[ OK ] Started Daily Cleanup of Temporary Directories.
636[ OK ] Started Message of the Day.
637[ OK ] Reached target Timers.
638[ OK ] Listening on D-Bus System Message Bus Socket.
639[ OK ] Reached target Sockets.
640[ OK ] Reached target Basic System.
641 Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"...
642 Starting System Logging Service...
643[ OK ] Started Regular background program processing daemon.
644 Starting Permit User Sessions...
645 Starting LSB: Xenstore daemon...
646[ OK ] Started D-Bus System Message Bus.
647[ 3.448251] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
648[ 3.743688] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
649[ 4.919062] sun50i-a64-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pd not found, using dummy regulator
650[ 4.919286] dwmac-sun8i 1c30000.ethernet: IRQ eth_wake_irq not found
651[ 4.919309] dwmac-sun8i 1c30000.ethernet: IRQ eth_lpi not found
652[ 4.919435] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
653[ 4.923953] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
654[ 4.923989] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
655[ 4.924010] dwmac-sun8i 1c30000.ethernet: COE Type 2
656[ 4.924027] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
657[ 4.924046] dwmac-sun8i 1c30000.ethernet: Normal descriptors
658[ 4.924065] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
659[ 4.924088] dwmac-sun8i 1c30000.ethernet: device MAC address ca:98:90:f1:b0:f6
660[ 4.924323] libphy: stmmac: probed
661[ 4.927377] mdio_bus stmmac-0: MDIO device at address 1 is missing.
662[ 5.434576] lima 1c40000.gpu: IRQ ppmmu2 not found
663[ 5.434615] lima 1c40000.gpu: IRQ ppmmu3 not found
664[ 5.434647] lima 1c40000.gpu: gp - mali400 version major 1 minor 1
665[ 5.434715] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1
666[ 5.434777] lima 1c40000.gpu: pp1 - mali400 version major 1 minor 1
667[ 5.434829] lima 1c40000.gpu: IRQ pp2 not found
668[ 5.434848] lima 1c40000.gpu: IRQ pp3 not found
669[ 5.434867] lima 1c40000.gpu: l2 cache 64K, 4-way, 64byte cache line, 64bit external bus
670[ 5.435433] lima 1c40000.gpu: bus rate = 200000000
671[ 5.435456] lima 1c40000.gpu: mod rate = 297000000
672[ 5.435899] [drm] Initialized lima 1.0.0 20190217 for 1c40000.gpu on minor 0
673 Starting Login Service...
674[ OK ] Started System Logging Service.
675[ OK ] Started Set console font and keymap.
676[ OK ] Started Permit User Sessions.
677[ 5.822995] sun4i-drm display-engine: bound 1100000.mixer (ops sun8i_mixer_ops [sun8i_mixer])
678[ 5.828992] sun4i-drm display-engine: bound 1200000.mixer (ops sun8i_mixer_ops [sun8i_mixer])
679[ 5.829646] sun4i-drm display-engine: No panel or bridge found... RGB output disabled
680[ 5.829698] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops sun4i_tcon_ops [sun4i_tcon])
681[ 5.830006] sun4i-drm display-engine: bound 1c0d000.lcd-controller (ops sun4i_tcon_ops [sun4i_tcon])
682[ 5.831747] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a with HDCP (sun8i_dw_hdmi_phy)
683[ 5.835836] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus driver
684[ 5.839358] sun4i-drm display-engine: bound 1ee0000.hdmi (ops sun8i_dw_hdmi_ops [sun8i_drm_hdmi])
685[ 5.839404] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
686[ 5.839421] [drm] No driver support for vblank timestamp query.
687[ 5.839865] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 1
688[ 5.840003] [drm] Cannot find any crtc or sizes
689[ OK ] Found device /dev/hvc0.
690[ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand".
691 Starting Set console scheme...
692[ OK ] Created slice system-getty.slice.
693[ OK ] Started Set console scheme.
694[ OK ] Started Login Service.
695[ OK ] Started LSB: Xenstore daemon.
696 Starting LSB: Xen daemons...
697[ 6.410368] xenbr0: port 1(eth0) entered blocking state
698[ 6.410406] xenbr0: port 1(eth0) entered disabled state
699[ 6.410676] device eth0 entered promiscuous mode
700[ 6.414801] dwmac-sun8i 1c30000.ethernet eth0: no phy at addr -1
701[ 6.414844] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
702[ OK ] Started ifup for xenbr0.
703[ OK ] Found device /sys/subsystem/net/devices/xenbr0.
704[FAILED] Failed to start LSB: Xen daemons.
705See 'systemctl status xen.service' for details.
706 Starting LSB: Start/stop secondary xen domains...
707[ OK ] Started LSB: Start/stop secondary xen domains.
708[ OK ] Started Raise network interfaces.
709[ OK ] Reached target Network.
710 Starting /etc/rc.local Compatibility...
711[ OK ] Started /etc/rc.local Compatibility.
712[ OK ] Started Getty on tty1.
713[ OK ] Started Serial Getty on hvc0.
714[ OK ] Reached target Login Prompts.
715[ OK ] Reached target Multi-User System.
716[ OK ] Reached target Graphical Interface.
717 Starting Update UTMP about System Runlevel Changes...
718[ OK ] Started Update UTMP about System Runlevel Changes.
719
720Ubuntu 16.04.6 LTS LXC_NAME hvc0