· 5 years ago · Feb 20, 2020, 01:46 AM
1BUFFALO CFE Version 1.00 [DDRCLK:533]
2Memory Test start(0x07E00000) end(0x08000000) size(2097152)
3Data line test start:0x07e00000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
4Address line test start:0x07e00000 len:0x200000 pattern 0xAAAAAAAA 0x55555555
5Fill test patnum:2
6fill Pattern 5555AAAA Writing... Reading...
7fill Pattern AAAA5555 Writing... Reading...
8decompressing
9Decompressing...done
10Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
11
12
13CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
14Build Date: Fri Jan 18 16:22:36 JST 2013 (root@fc17.localdomain)
15Copyright (C) 2000-2008 Broadcom Corporation.
16
17Memory Test start(0x00000000) end(0x07E00000) size(132120576)
18Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
19Address line test start:0x00000000 len:0x7e00000 pattern 0xAAAAAAAA 0x55555555
20Fill test patnum:2
21fill Pattern 5555AAAA Writing... Reading...
22fill Pattern AAAA5555 Writing... Reading...
23Memory Test start(0x88000000) end(0xA0000000) size(402653184)
24Data line test start:0x88000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
25Address line test start:0x88000000 len:0x18000000 pattern 0xAAAAAAAA 0x55555555
26Fill test patnum:2
27fill Pattern 5555AAAA Writing... Reading...
28fill Pattern AAAA5555 Writing... Reading...
29Init Arena
30Init Devs.
31Boot partition size = 262144(0x40000)
32Found a Esmt NAND flash:
33Total size: 128MB
34Block size: 128KB
35Page Size: 2048B
36OOB Size: 64B
37Sector size: 512B
38Spare size: 16B
39ECC level: 8-bit
40Device ID: 0x92 0xf1 0x80 0x95 0x40
41DDR Clock: 533 MHz
42Warning: using legacy sdram_ncdl parameter to set DDR frequency. Equivalent setting in clkfreq=800,*0* will be ignored.
43et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
44CPU type 0x0: 800MHz
45Tot mem: 524288 KBytes
46
47CFE mem: 0x07E00000 - 0x07F9A984 (1681796)
48Data: 0x07E53480 - 0x07E53948 (1224)
49BSS: 0x07E53958 - 0x07E98984 (282668)
50Heap: 0x07E98984 - 0x07F98984 (1048576)
51Stack: 0x07F98984 - 0x07F9A984 (8192)
52Text: 0x07E00000 - 0x07E488F0 (297200)
53Boot: 0x07F9B000 - 0x07FDB000
54Reloc: I:00000000 - D:00000000
55
56Device eth0: hwaddr B2-C7-45-XX-XX-XX, ipaddr 192.168.11.1, mask 255.255.255.0
57 gateway not set, nameserver not set
58Startup canceled
59CFE> flash -noheader 192.168.11.2:buffalo-wzr-1750dhp-webflash.bin nflash1.trx
60Reading 192.168.11.2:buffalo-wzr-1750dhp-webflash.bin: Done. 24285184 bytes read
61Programming...done. 24285184 bytes written
62*** command status = 0
63CFE> flash -noheader 192.168.11.2:buffalo-wzr-1750dhp-webflash.bin nflash1.trx
64Reading 192.168.11.2:buffalo-wzr-1750dhp-webflash.bin: Done. 24285184 bytes read
65Programming...done. 24285184 bytes written
66*** command status = 0
67CFE> nvram erase
68*** command status = 0
69CFE> reboot
70
71
72BUFFALO CFE Version 1.00 [DDRCLK:333]
73decompressing
74Decompressing...done
75Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
76Corrupt NVRAM found, trying embedded NVRAM next.
77
78
79CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
80Build Date: Fri Jan 18 16:22:36 JST 2013 (root@fc17.localdomain)
81Copyright (C) 2000-2008 Broadcom Corporation.
82
83Memory Test start(0x00000000) end(0x07E00000) size(132120576)
84Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
85Address line test start:0x00000000 len:0x7e00000 pattern 0xAAAAAAAA 0x55555555
86Fill test patnum:2
87fill Pattern 5555AAAA Writing... Reading...
88fill Pattern AAAA5555 Writing... Reading...
89Memory Test start(0x88000000) end(0xA0000000) size(402653184)
90Data line test start:0x88000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
91Address line test start:0x88000000 len:0x18000000 pattern 0xAAAAAAAA 0x55555555
92Fill test patnum:2
93fill Pattern 5555AAAA Writing... Reading...
94fill Pattern AAAA5555 Writing... Reading...
95Init Arena
96Init Devs.
97Boot partition size = 262144(0x40000)
98Found a Esmt NAND flash:
99Total size: 128MB
100Block size: 128KB
101Page Size: 2048B
102OOB Size: 64B
103Sector size: 512B
104Spare size: 16B
105ECC level: 8-bit
106Device ID: 0x92 0xf1 0x80 0x95 0x40
107DDR Clock: 333 MHz
108Warning: using legacy sdram_ncdl parameter to set DDR frequency. Equivalent setting in clkfreq=800,*0* will be ignored.
109Warning: invalid DDR setting of 533 MHz ignored. DDR frequency will be set to 333 MHz.
110et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
111CPU type 0x0: 800MHz
112Tot mem: 524288 KBytes
113
114CFE mem: 0x07E00000 - 0x07F9A984 (1681796)
115Data: 0x07E53480 - 0x07E53948 (1224)
116BSS: 0x07E53958 - 0x07E98984 (282668)
117Heap: 0x07E98984 - 0x07F98984 (1048576)
118Stack: 0x07F98984 - 0x07F9A984 (8192)
119Text: 0x07E00000 - 0x07E488F0 (297200)
120Boot: 0x07F9B000 - 0x07FDB000
121Reloc: I:00000000 - D:00000000
122
123initializing nvram...Corrupt NVRAM found, trying embedded NVRAM next.
124done
125commiting nvram...done
126now rebooting
127
128BUFFALO CFE Version 1.00 [DDRCLK:333]
129decompressing
130Decompressing...done
131Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
132et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
133
134DDR clock change and Calibrate... [333->533]
135
136
137BUFFALO CFE Version 1.00 [DDRCLK:533]
138Memory Test start(0x07E00000) end(0x08000000) size(2097152)
139Data line test start:0x07e00000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
140Address line test start:0x07e00000 len:0x200000 pattern 0xAAAAAAAA 0x55555555
141Fill test patnum:2
142fill Pattern 5555AAAA Writing... Reading...
143fill Pattern AAAA5555 Writing... Reading...
144decompressing
145Decompressing...done
146Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
147
148
149CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
150Build Date: Fri Jan 18 16:22:36 JST 2013 (root@fc17.localdomain)
151Copyright (C) 2000-2008 Broadcom Corporation.
152
153Memory Test start(0x00000000) end(0x07E00000) size(132120576)
154Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
155Address line test start:0x00000000 len:0x7e00000 pattern 0xAAAAAAAA 0x55555555
156Fill test patnum:2
157fill Pattern 5555AAAA Writing... Reading...
158fill Pattern AAAA5555 Writing... Reading...
159Memory Test start(0x88000000) end(0xA0000000) size(402653184)
160Data line test start:0x88000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
161Address line test start:0x88000000 len:0x18000000 pattern 0xAAAAAAAA 0x55555555
162Fill test patnum:2
163fill Pattern 5555AAAA Writing... Reading...
164fill Pattern AAAA5555 Writing... Reading...
165Init Arena
166Init Devs.
167Boot partition size = 262144(0x40000)
168Found a Esmt NAND flash:
169Total size: 128MB
170Block size: 128KB
171Page Size: 2048B
172OOB Size: 64B
173Sector size: 512B
174Spare size: 16B
175ECC level: 8-bit
176Device ID: 0x92 0xf1 0x80 0x95 0x40
177DDR Clock: 533 MHz
178Warning: using legacy sdram_ncdl parameter to set DDR frequency. Equivalent setting in clkfreq=800,*0* will be ignored.
179et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
180CPU type 0x0: 800MHz
181Tot mem: 524288 KBytes
182
183CFE mem: 0x07E00000 - 0x07F9A984 (1681796)
184Data: 0x07E53480 - 0x07E53948 (1224)
185BSS: 0x07E53958 - 0x07E98984 (282668)
186Heap: 0x07E98984 - 0x07F98984 (1048576)
187Stack: 0x07F98984 - 0x07F9A984 (8192)
188Text: 0x07E00000 - 0x07E488F0 (297200)
189Boot: 0x07F9B000 - 0x07FDB000
190Reloc: I:00000000 - D:00000000
191
192Committing NVRAM...done
193Device eth0: hwaddr B2-C7-45-XX-XX-XX, ipaddr 192.168.11.1, mask 255.255.255.0
194 gateway not set, nameserver not set
195check_trx: start nflash1.trx
196check_trx: exit nflash1.trx
197Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
198Loading: .. 1286104 bytes read
199Entry at 0x00008000
200Closing network.
201Starting program at 0x00008000
202Uncompressing Linux... done, booting the kernel.
203Booting Linux on physical CPU 0x0
204Linux version 3.10.30 (root@dd-wrt.buildserver) (gcc version 4.8.2 (OpenWrt/Linaro GCC 4.8-2013.10 r38451) ) #1533 SMP Wed Feb 19 05:53:26 CET 2014
205CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
206CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
207Machine: Northstar Prototype
208Ignoring unrecognised tag 0x00000000
209Memory policy: ECC disabled, Data cache writealloc
210map io
211MPCORE found at 19020000 (VIRT d9020000) 18000000 d8000000
212PERCPU: Embedded 7 pages/cpu @c1808000 s7040 r8192 d13440 u32768
213Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130816
214Kernel command line: console=ttyS0,115200 panic=10 root=/dev/mtdblock3 earlyprintk=1 rootfstype=squashfs,jffs2 noinitrd init=/bin/sh
215PID hash table entries: 512 (order: -1, 2048 bytes)
216Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
217Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
218Memory: 128MB 384MB = 512MB total
219Memory: 515892k/515892k available, 8396k reserved, 393216K highmem
220Virtual kernel memory layout:
221 vector : 0xffff0000 - 0xffff1000 ( 4 kB)
222 fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
223 vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
224 lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
225 pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
226 modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
227 .text : 0xc0008000 - 0xc0320da4 (3172 kB)
228 .init : 0xc0321000 - 0xc035ab80 ( 231 kB)
229 .data : 0xc035c000 - 0xc03987fc ( 242 kB)
230 .bss : 0xc03987fc - 0xc03f8e18 ( 386 kB)
231Hierarchical RCU implementation.
232 CONFIG_RCU_FANOUT set to non-default value of 2
233NR_IRQS:256
234MPCORE GIC init
235External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored.
236MPCORE Global Timer Clock 400000000Hz on IRQ 27
237sched_clock: 32 bits at 400MHz, resolution 2ns, wraps every 10737ms
238register local timer
239smp_twd: clock not found -2
240Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
241pid_max: default: 32768 minimum: 301
242Mount-cache hash table entries: 512
243CPU: Testing write buffer coherency: ok
244CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
245Calibrating local timer... 399.68MHz.
2462 cores has been found
247Setting up static identity map for 0xc0012440 - 0xc0012474
248L310: cache controller enabled 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7a130000
249CPU1: Booted secondary processor
250CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
251Brought up 2 CPUs
252SMP: Total of 2 processors activated (3188.32 BogoMIPS).
253NET: Registered protocol family 16
254DMA: preallocated 256 KiB pool for atomic coherent allocations
255Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
256found remapped nvram on sflash
257CCA UART Clock Config: Sel=1 Ovr=1 Div=48
258CCA UART Clock rate 100000000Hz
259bio: create slab <bio-0> at 0
260Switching to clocksource mpcore_gtimer
261NET: Registered protocol family 2
262TCP established hash table entries: 1024 (order: 1, 8192 bytes)
263TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
264TCP: Hash tables configured (established 1024 bind 1024)
265TCP: reno registered
266UDP hash table entries: 256 (order: 1, 8192 bytes)
267UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
268NET: Registered protocol family 1
269init gpio code
270Buffalo WZR-1750DHP
271PCI: no core
272PCI: no core
273PCI: scanning bus 0
274PCI host bridge to bus 0000:00
275pci_bus 0000:00: root bus resource [io 0x0000-0xffffffff]
276pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
277pci_bus 0000:00: root bus resource [bus 00-ff]
278PCI: Fixing up bus 0
279PCIE1 link=1
280PCIE1 switching to GEN2
281PCIE1 link=1
282PCI host bridge to bus 0001:00
283pci_bus 0001:00: root bus resource [mem 0x08000000-0x0fffffff]
284pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff]
285PCI: Fixing up bus 0
286PCI: bus0: Fast back to back transfers disabled
287PCI: Fixing up bus 1
288PCI: bus1: Fast back to back transfers disabled
289pci 0001:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
290pci 0001:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
291pci 0001:00:00.0: PCI bridge to [bus 01]
292pci 0001:00:00.0: bridge window [mem 0x08000000-0x080fffff]
293PCIE2 link=1
294PCIE2 switching to GEN2
295PCIE2 link=1
296PCI host bridge to bus 0002:00
297pci_bus 0002:00: root bus resource [mem 0x40000000-0x47ffffff]
298pci_bus 0002:00: No busn resource found for root bus, will use [bus 00-ff]
299PCI: Fixing up bus 0
300PCI: bus0: Fast back to back transfers disabled
301PCI: Fixing up bus 2
302PCI: bus2: Fast back to back transfers disabled
303pci 0002:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff]
304pci 0002:02:00.0: BAR 0: assigned [mem 0x40000000-0x40003fff 64bit]
305pci 0002:00:00.0: PCI bridge to [bus 02]
306pci 0002:00:00.0: bridge window [mem 0x40000000-0x400fffff]
307PCIE3 link=0
308Error creating gpio class
309squashfs: version 3.0 (2006/03/15) Phillip Lougher
310msgmni has been set to 239
311alg: No test for stdrng (krng)
312io scheduler noop registered (default)
313io scheduler cfq registered
314Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
315serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117) is a 16550
316console [ttyS0] enabled
317serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
318brd: module loaded
319loop: module loaded
320Creating 5 MTD partitions on "bcmsflash":
3210x000000000000-0x000000100000 : "boot"
3220x000000000000-0x0000000f0000 : "linux"
3230x000000100000-0x000000100000 : "rootfs"
324mtd: partition "rootfs" is out of reach -- disabled
3250x0000000f0000-0x000000100000 : "nvram_cfe"
3260x0000000e0000-0x0000000f0000 : "nvram"
327Found a Esmt NAND flash:
328Total size: 128MB
329Block size: 128KB
330Page Size: 2048B
331OOB Size: 64B
332Sector size: 512B
333Spare size: 16B
334ECC level: 8 (8-bit)
335Device ID: 0x92 0xf1 0x80 0x95 0x40 0x7f
336Creating 1 MTD partitions on "nflash":
3370x000000000000-0x000008000000 : "nand"
338tun: Universal TUN/TAP device driver, 1.6
339tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
340PPP generic driver version 2.4.2
341PPP BSD Compression module registered
342PPP Deflate Compression module registered
343PPP MPPE Compression module registered
344NET: Registered protocol family 24
345GACT probability NOT on
346Mirror/redirect action on
347Failed to load ipt action
348Simple TC action Loaded
349netem: version 1.3
350u32 classifier
351 Performance counters on
352 input device check on
353 Actions configured
354Netfilter messages via NETLINK v0.30.
355nf_conntrack version 0.5.0 (8060 buckets, 32240 max)
356nf_conntrack_rtsp v0.6.21 loading
357xt_time: kernel timezone is -0000
358ip_set: protocol 6
359gre: GRE over IPv4 demultiplexor driver
360nf_nat_rtsp v0.6.21 loading
361ip_tables: (C) 2000-2006 Netfilter Core Team
362TCP: bic registered
363TCP: cubic registered
364TCP: westwood registered
365TCP: highspeed registered
366TCP: hybla registered
367TCP: htcp registered
368TCP: vegas registered
369TCP: veno registered
370TCP: scalable registered
371TCP: lp registered
372TCP: yeah registered
373TCP: illinois registered
374NET: Registered protocol family 17
375Bridge firewalling registered
3768021q: 802.1Q VLAN Support v1.8
377found cfe nvram
378Key type encrypted registered
379Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
380NAND device: Manufacturer ID: 0x92, Chip ID: 0xf1 (Eon NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
381Spare area=64 eccbytes 56, ecc bytes located at:
382 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
383Available 7 bytes at (off,len):
384(1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0)
385Driver must set ecc.strength when using hardware ECC
386Scanning device for bad blocks
387Options: NO_SUBPAGE_WRITE,
388Creating 1 MTD partitions on "brcmnand":
3890x000000000000-0x000008000000 : "ddwrt"
390end_request: I/O error, dev mtdblock2, sector 0
391SQUASHFS error: sb_bread failed reading block 0x0
392VFS: Cannot open root device "1f02" or unknown-block(31,2): error -19
393Please append a correct "root=" boot option; here are the available partitions:
3941f00 1024 mtdblock0 (driver?)
3951f01 960 mtdblock1 (driver?)
3961f03 64 mtdblock3 (driver?)
3971f04 64 mtdblock4 (driver?)
3981f05 131072 mtdblock5 (driver?)
3991f06 131072 mtdblock6 (driver?)
400Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
401CPU1: stopping
402CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.10.30 #1533
403Backtrace:
404Function entered at [<c00157d8>] from [<c0015994>]
405 r6:00000000 r5:00000001 r4:c0359b60 r3:00000000
406Function entered at [<c001597c>] from [<c0126e08>]
407Function entered at [<c0126de4>] from [<c001725c>]
408Function entered at [<c001717c>] from [<c00086d8>]
409 r6:c7857f70 r5:c0370640 r4:f010010c r3:c001355c
410Function entered at [<c0008678>] from [<c0008860>]
411Exception stack(0xc7857f70 to 0xc7857fb8)
4127f60: c1810778 00000000 00000ba2 00000000
4137f80: c7856000 c7856000 c0370470 c02d5be0 c7856000 c0377b67 c0377b67 c7857fc4
4147fa0: c7857fc8 c7857fb8 c001355c c0013560 60000113 ffffffff
415 r7:c7857fa4 r6:ffffffff r5:60000113 r4:c0013560
416Function entered at [<c0013530>] from [<c005cc18>]
417Function entered at [<c005cb40>] from [<c033d1f8>]
418 r7:c03991a8 r3:00000002
419Function entered at [<c033d0bc>] from [<0033c860>]
420 r4:0783806a r3:c033c848
421Rebooting in 10 seconds..