· 6 years ago · Nov 10, 2019, 09:12 PM
1U-Boot SPL 2019.01-1-00035-g64abfc9b6b (Jan 11 2019 - 19:47:34 +0000)
2DRAM: 2048 MiB
3Trying to boot from MMC1
4NOTICE: BL31: v2.0(debug):v2.0-517-g63b9b542-dirty
5NOTICE: BL31: Built : 19:47:34, Jan 11 2019
6NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689)
7NOTICE: BL31: Found U-Boot DTB at 0x4080108, model: Pine64+
8INFO: ARM GICv2 driver initialized
9INFO: Configuring SPC Controller
10NOTICE: BL31: PMIC: Detected AXP803 on RSB.
11INFO: PMIC: AXP803: dcdc1 voltage: 3.300V
12INFO: PMIC: AXP803: dcdc5 voltage: 1.360V
13INFO: PMIC: AXP803: dcdc6 voltage: 1.100V
14INFO: PMIC: AXP803: dldo1 voltage: 3.300V
15INFO: PMIC: AXP803: Enabling DC1SW
16INFO: BL31: Platform setup done
17INFO: BL31: Initializing runtime services
18INFO: BL31: cortex_a53: CPU workaround for 843419 was applied
19INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
20INFO: BL31: Preparing for EL3 exit to normal world
21INFO: Entry point address = 0x4a000000
22INFO: SPSR = 0x3c9
23
24
25U-Boot 2019.01-1-00035-g64abfc9b6b (Jan 11 2019 - 19:47:34 +0000) Arch Linux
26ARM
27
28CPU: Allwinner A64 (SUN50I)
29Model: Pine64+
30DRAM: 2 GiB
31MMC: SUNXI SD/MMC: 0
32Loading Environment from FAT... Unable to use mmc 0:1... In: serial
33Out: vidconsole
34Err: vidconsole
35Net: phy interface7
36eth0: ethernet@1c30000
37starting USB...
38USB0: USB EHCI 1.00
39USB1: USB OHCI 1.0
40USB2: USB EHCI 1.00
41USB3: USB OHCI 1.0
42scanning bus 0 for devices... 1 USB Device(s) found
43scanning bus 2 for devices... 2 USB Device(s) found
44 scanning usb for storage devices... 0 Storage Device(s) found
45Hit any key to stop autoboot: 0
46switch to partitions #0, OK
47mmc0 is current device
48Scanning mmc 0:1...
49Found U-Boot script /boot.scr
50963 bytes read in 5 ms (187.5 KiB/s)
51## Executing script at 4fc00000
5223923200 bytes read in 9877 ms (2.3 MiB/s)
53** File not found initrd.img **
5426814 bytes read in 4 ms (6.4 MiB/s)
55## Flattened Device Tree blob at 4fa00000
56 Booting using the fdt blob at 0x4fa00000
57EHCI failed to shut down host controller.
58EHCI failed to shut down host controller.
59 Loading Ramdisk to 4892f000, end 49fffa00 ... OK
60 Loading Device Tree to 0000000048925000, end 000000004892e8bd ... OK
61
62Starting kernel ...
63
64[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
65[ 0.000000] Linux version 5.3.0-3-MANJARO-ARM (root@aarch64) (gcc version
669.1.0 (GCC)) #1 SMP Sat Oct 12 11:05:00 UTC 2019
67[ 0.000000] Machine model: BananaPi-M64
68[ 0.000000] efi: Getting EFI parameters from FDT:
69[ 0.000000] efi: UEFI not found.
70[ 0.000000] cma: Reserved 64 MiB at 0x00000000ba000000
71[ 0.000000] psci: probing for conduit method from DT.
72[ 0.000000] psci: PSCIv1.1 detected in firmware.
73[ 0.000000] psci: Using standard PSCI v0.2 function IDs
74[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
75[ 0.000000] psci: SMC Calling Convention v1.1
76[ 0.000000] percpu: Embedded 43 pages/cpu s138264 r8192 d29672 u176128
77[ 0.000000] Detected VIPT I-cache on CPU0
78[ 0.000000] CPU features: detected: ARM erratum 843419
79[ 0.000000] Speculative Store Bypass Disable mitigation not required
80[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 508032
81[ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk root=/de
82v/mmcblk0p2 rw rootfstype=ext4 rootwait fsck.repair=yes panic=10
83[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 byt
84es, linear)
85[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 byte
86s, linear)
87[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
88[ 0.000000] Memory: 1894528K/2064384K available (14076K kernel code, 1858K
89 rwdata, 5748K rodata, 1600K init, 16715K bss, 104320K reserved, 65536K cma-r
90eserved)
91[ 0.000000] random: get_random_u64 called from cache_random_seq_create+0x8
928/0x158 with crng_init=0
93[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
94[ 0.000000] ftrace: allocating 48808 entries in 191 pages
95[ 0.000000] rcu: Hierarchical RCU implementation.
96[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
97[ 0.000000] Tasks RCU enabled.
98[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10
99jiffies.
100[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
101[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
102[ 0.000000] GIC: Using split EOI/Deactivate mode
103[ 0.000000] arch_timer: Enabling global workaround for Allwinner erratum U
104NKNOWN1
105[ 0.000000] arch_timer: CPU0: Trapping CNTVCT access
106[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
107[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycl
108es: 0x588fe9dc0, max_idle_ns: 440795202592 ns
109[ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43
11098046511097ns
111[ 0.000385] Console: colour dummy device 80x25
112[ 0.000430] Calibrating delay loop (skipped), value calculated using timer
113 frequency.. 48.00 BogoMIPS (lpj=240000)
114[ 0.000442] pid_max: default: 32768 minimum: 301
115[ 0.000639] LSM: Security Framework initializing
116[ 0.000658] Yama: becoming mindful.
117[ 0.000752] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, l
118inear)
119[ 0.000774] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 byt
120es, linear)
121[ 0.002532] ASID allocator initialised with 32768 entries
122[ 0.002632] rcu: Hierarchical SRCU implementation.
123[ 0.005055] EFI services will not be available.
124[ 0.005360] smp: Bringing up secondary CPUs ...
125[ 0.006812] Detected VIPT I-cache on CPU1
126[ 0.006870] arch_timer: CPU1: Trapping CNTVCT access
127[ 0.006881] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
128[ 0.008025] Detected VIPT I-cache on CPU2
129[ 0.008056] arch_timer: CPU2: Trapping CNTVCT access
130[ 0.008064] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
131[ 0.009038] Detected VIPT I-cache on CPU3
132[ 0.009064] arch_timer: CPU3: Trapping CNTVCT access
133[ 0.009072] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
134[ 0.009157] smp: Brought up 1 node, 4 CPUs
135[ 0.009183] SMP: Total of 4 processors activated.
136[ 0.009191] CPU features: detected: 32-bit EL0 Support
137[ 0.009199] CPU features: detected: CRC32 instructions
138[ 0.009740] CPU: All CPU(s) started at EL2
139[ 0.009763] alternatives: patching kernel code
140[ 0.011944] devtmpfs: initialized
141[ 0.019219] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
142 max_idle_ns: 19112604462750000 ns
143[ 0.019245] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
144[ 0.022141] pinctrl core: initialized pinctrl subsystem
145[ 0.023017] DMI not present or invalid.
146[ 0.023400] NET: Registered protocol family 16
147[ 0.024891] cpuidle: using governor ladder
148[ 0.025009] cpuidle: using governor menu
149[ 0.025302] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
150[ 0.027012] DMA: preallocated 256 KiB pool for atomic allocations
151[ 0.027239] Serial: AMBA PL011 UART driver
152[ 0.047188] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
153[ 0.047203] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
154[ 0.047211] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
155[ 0.047218] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
156[ 1.654812] cryptd: max_cpu_qlen set to 1000
157[ 1.666387] alg: No test for lzo-rle (lzo-rle-generic)
158[ 1.666604] alg: No test for lzo-rle (lzo-rle-scomp)
159[ 1.682421] ACPI: Interpreter disabled.
160[ 1.682756] vgaarb: loaded
161[ 1.683676] SCSI subsystem initialized
162[ 1.684092] usbcore: registered new interface driver usbfs
163[ 1.684145] usbcore: registered new interface driver hub
164[ 1.684203] usbcore: registered new device driver usb
165[ 1.684479] mc: Linux media interface: v0.10
166[ 1.684519] videodev: Linux video capture interface: v2.00
167[ 1.684566] pps_core: LinuxPPS API ver. 1 registered
168[ 1.684572] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Gi
169ometti <giometti@linux.it>
170[ 1.684589] PTP clock support registered
171[ 1.684772] EDAC MC: Ver: 3.0.0
172[ 1.685369] Advanced Linux Sound Architecture Driver Initialized.
173[ 1.685925] NetLabel: Initializing
174[ 1.685932] NetLabel: domain hash size = 128
175[ 1.685937] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
176[ 1.686006] NetLabel: unlabeled traffic allowed by default
177[ 1.686487] clocksource: Switched to clocksource arch_sys_counter
178[ 2.730451] VFS: Disk quotas dquot_6.6.0
179[ 2.730537] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
180[ 2.731442] pnp: PnP ACPI: disabled
181[ 2.738371] thermal_sys: Registered thermal governor 'fair_share'
182[ 2.738376] thermal_sys: Registered thermal governor 'bang_bang'
183[ 2.738387] thermal_sys: Registered thermal governor 'step_wise'
184[ 2.738393] thermal_sys: Registered thermal governor 'user_space'
185[ 2.738399] thermal_sys: Registered thermal governor 'power_allocator'
186[ 2.739198] NET: Registered protocol family 2
187[ 2.739792] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 1
1886384 bytes, linear)
189[ 2.739844] TCP established hash table entries: 16384 (order: 5, 131072 by
190tes, linear)
191[ 2.740007] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, li
192near)
193[ 2.740329] TCP: Hash tables configured (established 16384 bind 16384)
194[ 2.740469] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
195[ 2.740532] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, line
196ar)
197[ 2.740773] NET: Registered protocol family 1
198[ 2.741393] RPC: Registered named UNIX socket transport module.
199[ 2.741401] RPC: Registered udp transport module.
200[ 2.741407] RPC: Registered tcp transport module.
201[ 2.741412] RPC: Registered tcp NFSv4.1 backchannel transport module.
202[ 2.741426] PCI: CLS 0 bytes, default 64
203[ 2.741608] Trying to unpack rootfs image as initramfs...
204[ 2.741622] Initramfs unpacking failed: invalid magic at start of compress
205ed archive
206[ 2.758953] Freeing initrd memory: 23360K
207[ 2.759834] kvm [1]: IPA Size Limit: 40bits
208[ 2.762615] kvm [1]: vgic interrupt IRQ1
209[ 2.762760] kvm [1]: Hyp mode initialized successfully
210[ 2.819061] Initialise system trusted keyrings
211[ 2.819214] workingset: timestamp_bits=46 max_order=19 bucket_order=0
212[ 2.826196] zbud: loaded
213[ 2.828822] NFS: Registering the id_resolver key type
214[ 2.828854] Key type id_resolver registered
215[ 2.828860] Key type id_legacy registered
216[ 2.828875] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
217[ 2.828909] ntfs: driver 2.1.32 [Flags: R/W].
218[ 2.829417] fuse: init (API version 7.31)
219[ 2.829826] SGI XFS with ACLs, security attributes, no debug enabled
220[ 2.852166] NET: Registered protocol family 38
221[ 2.852189] Key type asymmetric registered
222[ 2.852197] Asymmetric key parser 'x509' registered
223[ 2.852249] Block layer SCSI generic (bsg) driver version 0.4 loaded (majo
224r 244)
225[ 2.852395] io scheduler mq-deadline registered
226[ 2.852404] io scheduler kyber registered
227[ 2.852705] atomic64_test: passed
228[ 2.852939] sun50i-de2-bus 1000000.bus: Error couldn't map SRAM to device
229[ 2.853542] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO
230[ 2.857042] sun50i-a64-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO dr
231iver
232[ 2.858519] IPMI message handler: version 39.2
233[ 2.867386] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
234[ 2.876767] libphy: Fixed MDIO Bus: probed
235[ 2.877404] usbcore: registered new interface driver asix
236[ 2.877451] usbcore: registered new interface driver ax88179_178a
237[ 2.878719] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
238[ 2.878735] ehci-pci: EHCI PCI platform driver
239[ 2.878781] ehci-platform: EHCI generic platform driver
240[ 2.879001] ehci-platform 1c1a000.usb: EHCI Host Controller
241[ 2.879156] ehci-platform 1c1a000.usb: new USB bus registered, assigned bu
242s number 1
243[ 2.879300] ehci-platform 1c1a000.usb: irq 15, io mem 0x01c1a000
244[ 2.906500] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
245[ 2.906720] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002,
246 bcdDevice= 5.03
247[ 2.906731] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumb
248er=1
249[ 2.906740] usb usb1: Product: EHCI Host Controller
250[ 2.906749] usb usb1: Manufacturer: Linux 5.3.0-3-MANJARO-ARM ehci_hcd
251[ 2.906757] usb usb1: SerialNumber: 1c1a000.usb
252[ 2.907239] hub 1-0:1.0: USB hub found
253[ 2.907275] hub 1-0:1.0: 1 port detected
254[ 2.907934] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
255[ 2.907953] ohci-pci: OHCI PCI platform driver
256[ 2.908027] ohci-platform: OHCI generic platform driver
257[ 2.908203] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
258[ 2.908366] ohci-platform 1c1a400.usb: new USB bus registered, assigned bu
259s number 2
260[ 2.908470] ohci-platform 1c1a400.usb: irq 16, io mem 0x01c1a400
261[ 2.980707] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001,
262 bcdDevice= 5.03
263[ 2.980718] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumb
264er=1
265[ 2.980727] usb usb2: Product: Generic Platform OHCI controller
266[ 2.980736] usb usb2: Manufacturer: Linux 5.3.0-3-MANJARO-ARM ohci_hcd
267[ 2.980744] usb usb2: SerialNumber: 1c1a400.usb
268[ 2.981199] hub 2-0:1.0: USB hub found
269[ 2.981245] hub 2-0:1.0: 1 port detected
270[ 2.981883] uhci_hcd: USB Universal Host Controller Interface driver
271[ 2.982443] usbcore: registered new interface driver uas
272[ 2.982534] usbcore: registered new interface driver usb-storage
273[ 2.982571] usbcore: registered new interface driver ums-alauda
274[ 2.982607] usbcore: registered new interface driver ums-cypress
275[ 2.982649] usbcore: registered new interface driver ums-datafab
276[ 2.982686] usbcore: registered new interface driver ums_eneub6250
277[ 2.982730] usbcore: registered new interface driver ums-freecom
278[ 2.982768] usbcore: registered new interface driver ums-isd200
279[ 2.982803] usbcore: registered new interface driver ums-jumpshot
280[ 2.982838] usbcore: registered new interface driver ums-karma
281[ 2.982874] usbcore: registered new interface driver ums-onetouch
282[ 2.982928] usbcore: registered new interface driver ums-realtek
283[ 2.982965] usbcore: registered new interface driver ums-sddr09
284[ 2.983002] usbcore: registered new interface driver ums-sddr55
285[ 2.983039] usbcore: registered new interface driver ums-usbat
286[ 2.983138] usbcore: registered new interface driver usbserial_generic
287[ 2.983170] usbserial: USB Serial support registered for generic
288[ 2.983501] musb-sunxi 1c19000.usb: Invalid or missing 'dr_mode' property
289[ 2.983518] musb-sunxi: probe of 1c19000.usb failed with error -22
290[ 2.984711] mousedev: PS/2 mouse device common for all mice
291[ 2.985472] sun6i-rtc 1f00000.rtc: registered as rtc0
292[ 2.985482] sun6i-rtc 1f00000.rtc: RTC enabled
293[ 2.987460] device-mapper: uevent: version 1.0.3
294[ 2.987767] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: d
295m-devel@redhat.com
296[ 2.988676] sun50i-a64-r-pinctrl 1f02c00.pinctrl: 1f02c00.pinctrl supply v
297cc-pl not found, using dummy regulator
298[ 2.988997] sdhci: Secure Digital Host Controller Interface driver
299[ 2.989003] sdhci: Copyright(c) Pierre Ossman
300[ 2.989562] Synopsys Designware Multimedia Card Interface Driver
301[ 2.990398] sdhci-pltfm: SDHCI platform and OF driver helper
302[ 2.991012] ledtrig-cpu: registered to indicate activity on CPUs
303[ 2.991279] hidraw: raw HID events driver (C) Jiri Kosina
304[ 2.991403] usbcore: registered new interface driver usbhid
305[ 2.991408] usbhid: USB HID core driver
306[ 2.995329] drop_monitor: Initializing network drop monitor service
307[ 2.995579] Initializing XFRM netlink socket
308[ 2.996310] NET: Registered protocol family 10
309[ 3.000728] Segment Routing with IPv6
310[ 3.000821] mip6: Mobile IPv6
311[ 3.000833] NET: Registered protocol family 17
312[ 3.000923] Key type dns_resolver registered
313[ 3.001853] registered taskstats version 1
314[ 3.001861] Loading compiled-in X.509 certificates
315[ 3.001983] zswap: loaded using pool lzo/zbud
316[ 3.002239] Key type big_key registered
317[ 3.003637] Key type encrypted registered
318[ 3.047614] sun4i-drm display-engine: bound 1100000.mixer (ops sun8i_mixer
319_ops)
320[ 3.049543] sun4i-drm display-engine: bound 1200000.mixer (ops sun8i_mixer
321_ops)
322[ 3.049997] sun4i-drm display-engine: No panel or bridge found... RGB outp
323ut disabled
324[ 3.050017] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops su
325n4i_tcon_ops)
326[ 3.050223] sun4i-drm display-engine: bound 1c0d000.lcd-controller (ops su
327n4i_tcon_ops)
328[ 3.050286] sun8i-dw-hdmi 1ee0000.hdmi: Couldn't get regulator
329[ 3.050308] sun4i-drm display-engine: failed to bind 1ee0000.hdmi (ops sun
3308i_dw_hdmi_ops): -517
331[ 3.050601] sun4i-drm display-engine: Couldn't bind all pipelines componen
332ts
333[ 3.050732] sun4i-drm display-engine: master bind failed: -517
334[ 3.051335] sunxi-rsb 1f03400.rsb: RSB running at 3000000 Hz
335[ 3.051731] axp20x-rsb sunxi-rsb-3a3: AXP20x variant AXP803 found
336[ 3.054797] axp20x-adc axp813-adc: DMA mask not set
337[ 3.055630] axp20x-battery-power-supply axp20x-battery-power-supply: DMA m
338ask not set
339[ 3.055856] power_supply axp20x-battery: hwmon: 'axp20x-battery' is not a
340valid name attribute, please fix
341[ 3.056407] axp20x-ac-power-supply axp20x-ac-power-supply: DMA mask not se
342t
343[ 3.056607] power_supply axp813-ac: hwmon: 'axp813-ac' is not a valid name
344 attribute, please fix
345[ 3.057896] axp20x-usb-power-supply axp20x-usb-power-supply: DMA mask not
346set
347[ 3.058051] power_supply axp20x-usb: hwmon: 'axp20x-usb' is not a valid na
348me attribute, please fix
349[ 3.059346] dcdc1: supplied by regulator-dummy
350[ 3.059748] dcdc2: supplied by regulator-dummy
351[ 3.060009] dcdc4: supplied by regulator-dummy
352[ 3.060258] dcdc5: supplied by regulator-dummy
353[ 3.060353] vcc-dram: Bringing 1360000uV into 1500000-1500000uV
354[ 3.060603] dcdc6: supplied by regulator-dummy
355[ 3.060869] dc1sw: supplied by regulator-dummy
356[ 3.061101] aldo1: supplied by regulator-dummy
357[ 3.061196] afvcc-csi: Bringing 3300000uV into 2800000-2800000uV
358[ 3.061474] aldo2: supplied by regulator-dummy
359[ 3.061724] aldo3: supplied by regulator-dummy
360[ 3.061992] dldo1: supplied by regulator-dummy
361[ 3.062266] dldo2: supplied by regulator-dummy
362[ 3.062332] vcc-wifi: Bringing 2900000uV into 3300000-3300000uV
363[ 3.062568] dldo3: supplied by regulator-dummy
364[ 3.062831] dldo4: supplied by regulator-dummy
365[ 3.063127] eldo1: supplied by regulator-dummy
366[ 3.063384] eldo2: supplied by regulator-dummy
367[ 3.063651] eldo3: supplied by regulator-dummy
368[ 3.063939] fldo1: supplied by regulator-dummy
369[ 3.064209] fldo2: supplied by regulator-dummy
370[ 3.064484] rtc-ldo: supplied by regulator-dummy
371[ 3.064727] ldo-io0: supplied by regulator-dummy
372[ 3.064980] ldo-io1: supplied by regulator-dummy
373[ 3.065280] drivevbus: supplied by regulator-dummy
374[ 3.065484] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded
375[ 3.065723] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO
376[ 3.070594] sun50i-a64-pinctrl 1c20800.pinctrl: initialized sunXi PIO driv
377er
378[ 3.070933] sun50i-a64-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc
379-pb not found, using dummy regulator
380[ 3.071402] printk: console [ttyS0] disabled
381[ 3.092069] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 25, base_baud =
382 1500000) is a U6_16550A
383[ 4.628075] printk: console [ttyS0] enabled
384[ 4.633162] sun50i-a64-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc
385-pg not found, using dummy regulator
386[ 4.664219] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 26, base_baud =
387 1500000) is a U6_16550A
388[ 4.673324] serial serial0: tty port ttyS1 registered
389[ 4.679112] sun50i-a64-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc
390-pd not found, using dummy regulator
391[ 4.689387] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
392[ 4.695432] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the
393default 6 (expect 0)
394[ 4.704063] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register suppo
395rted
396[ 4.711287] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine suppo
397rted
398[ 4.718510] dwmac-sun8i 1c30000.ethernet: COE Type 2
399[ 4.723468] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
400[ 4.730259] dwmac-sun8i 1c30000.ethernet: Normal descriptors
401[ 4.735911] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
402[ 4.741710] libphy: stmmac: probed
403[ 4.748414] sun50i-a64-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc
404-ph not found, using dummy regulator
405[ 4.759588] thermal thermal_zone0: failed to read out thermal zone (-16)
406[ 4.766323] thermal thermal_zone1: failed to read out thermal zone (-16)
407[ 4.773069] thermal thermal_zone2: failed to read out thermal zone (-16)
408[ 4.781455] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 79200
4090 KHz
410[ 4.791788] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency chan
411ged to: 816000 KHz
412[ 4.800481] thermal thermal_zone0: failed to read out thermal zone (-16)
413[ 4.809668] sun50i-a64-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc
414-pf not found, using dummy regulator
415[ 4.820206] sunxi-mmc 1c0f000.mmc: Got CD GPIO
416[ 4.851658] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 K
417B, uses new timings mode
418[ 4.862215] sunxi-mmc 1c10000.mmc: allocated mmc-pwrseq
419[ 4.893128] sunxi-mmc 1c10000.mmc: initialized, max. request size: 16384 K
420B, uses new timings mode
421[ 4.903208] sun50i-a64-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc
422-pc not found, using dummy regulator
423[ 4.930416] mmc0: new high speed SDHC card at address aaaa
424[ 4.942083] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
425[ 4.959114] mmcblk0: mmc0:aaaa SS16G 14.8 GiB
426[ 4.963561] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
427[ 4.969082] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB
428, uses new timings mode
429[ 4.978958] sun50i-a64-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc
430-pe not found, using dummy regulator
431[ 4.989859] simple-framebuffer be000000.framebuffer: framebuffer at 0xbe00
4320000, 0x7e9000 bytes, mapped to 0x(____ptrval____)
433[ 5.001080] simple-framebuffer be000000.framebuffer: format=x8r8g8b8, mode
434=1920x1080x32, linelength=7680
435[ 5.010621] mmcblk0: p1 p2
436[ 5.014635] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
437[ 5.049952] Console: switching to colour frame buffer device 240x67
438[ 5.081268] simple-framebuffer be000000.framebuffer: fb0: simplefb registe
439red!
440[ 5.089099] random: fast init done
441[ 5.090421] sun4i-drm display-engine: bound 1100000.mixer (ops sun8i_mixer
442_ops)
443[ 5.101247] sun4i-drm display-engine: bound 1200000.mixer (ops sun8i_mixer
444_ops)
445[ 5.108866] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
446[ 5.114419] sun4i-drm display-engine: No panel or bridge found... RGB outp
447ut disabled
448[ 5.122269] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops su
449n4i_tcon_ops)
450[ 5.130423] sun4i-drm display-engine: bound 1c0d000.lcd-controller (ops su
451n4i_tcon_ops)
452[ 5.144509] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a
453 with HDCP (sun8i_dw_hdmi_phy)
454[ 5.154369] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus
455 driver
456[ 5.162265] sun4i-drm display-engine: bound 1ee0000.hdmi (ops sun8i_dw_hdm
457i_ops)
458[ 5.169683] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
459[ 5.176286] [drm] No driver support for vblank timestamp query.
460[ 5.182223] fb0: switching to sun4i-drm-fb from simple
461[ 5.190589] Console: switching to colour dummy device 80x25
462[ 5.196633] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine
463on minor 0
464[ 5.234928] mmc2: new DDR MMC card at address 0001
465[ 5.241216] mmcblk2: mmc2:0001 8GTF4R 7.28 GiB
466[ 5.246765] mmcblk2boot0: mmc2:0001 8GTF4R partition 1 4.00 MiB
467[ 5.253661] mmcblk2boot1: mmc2:0001 8GTF4R partition 2 4.00 MiB
468[ 5.311301] mmc1: new high speed SDIO card at address 0001
469[ 5.758720] Console: switching to colour frame buffer device 240x67
470[ 5.806057] sun4i-drm display-engine: fb0: sun4i-drmdrmfb frame buffer dev
471ice
472[ 5.814522] ehci-platform 1c1b000.usb: EHCI Host Controller
473[ 5.820323] ehci-platform 1c1b000.usb: new USB bus registered, assigned bu
474s number 3
475[ 5.828160] ehci-platform 1c1b000.usb: irq 17, io mem 0x01c1b000
476[ 5.859157] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00
477[ 5.865548] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002,
478 bcdDevice= 5.03
479[ 5.873833] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumb
480er=1
481[ 5.881068] usb usb3: Product: EHCI Host Controller
482[ 5.885943] usb usb3: Manufacturer: Linux 5.3.0-3-MANJARO-ARM ehci_hcd
483[ 5.892478] usb usb3: SerialNumber: 1c1b000.usb
484[ 5.900539] hub 3-0:1.0: USB hub found
485[ 5.904306] hub 3-0:1.0: 1 port detected
486[ 5.908953] ohci-platform 1c1b400.usb: Generic Platform OHCI controller
487[ 5.915697] ohci-platform 1c1b400.usb: new USB bus registered, assigned bu
488s number 4
489[ 5.923548] ohci-platform 1c1b400.usb: irq 18, io mem 0x01c1b400
490[ 6.000851] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001,
491 bcdDevice= 5.03
492[ 6.009130] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumb
493er=1
494[ 6.016345] usb usb4: Product: Generic Platform OHCI controller
495[ 6.022280] usb usb4: Manufacturer: Linux 5.3.0-3-MANJARO-ARM ohci_hcd
496[ 6.028815] usb usb4: SerialNumber: 1c1b400.usb
497[ 6.037306] hub 4-0:1.0: USB hub found
498[ 6.041070] hub 4-0:1.0: 1 port detected
499[ 6.045316] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01T00:0
5000:20 UTC (20)
501[ 6.053578] cpvdd: disabling
502[ 6.056498] ALSA device list:
503[ 6.059462] No soundcards found.
504[ 6.063122] md: Waiting for all devices to be available before autodetect
505[ 6.069914] md: If you don't use raid, use raid=noautodetect
506[ 6.076059] md: Autodetecting RAID arrays.
507[ 6.080278] md: autorun ...
508[ 6.083065] md: ... autorun DONE.
509[ 6.111130] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode
510. Opts: (null)
511[ 6.119331] VFS: Mounted root (ext4 filesystem) on device 179:2.
512[ 6.137182] devtmpfs: mounted
513[ 6.143266] Freeing unused kernel memory: 1600K
514[ 6.149935] Run /sbin/init as init process
515[ 6.286562] usb 3-1: new high-speed USB device number 2 using ehci-platfor
516m
517[ 6.487205] usb 3-1: New USB device found, idVendor=1a40, idProduct=0101,
518bcdDevice= 1.11
519[ 6.495384] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumbe
520r=0
521[ 6.502556] usb 3-1: Product: USB 2.0 Hub
522[ 6.507326] hub 3-1:1.0: USB hub found
523[ 6.511189] hub 3-1:1.0: 4 ports detected
524[ 6.724111] systemd[1]: System time before build time, advancing clock.
525[ 6.760249] systemd[1]: systemd 243.78-2-arch running in system mode. (+PA
526M +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYP
527T +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 def
528ault-hierarchy=hybrid)
529[ 6.782927] systemd[1]: Detected architecture arm64.
530
531Welcome to Manjaro ARM!
532
533[ 6.850174] systemd[1]: Set hostname to <Manjaro-BPI-M64>.
534[ 7.537242] random: systemd: uninitialized urandom read (16 bytes read)
535[ 7.546718] systemd[1]: Created slice system-getty.slice.
536[ OK ] Created slice system-getty.slice.
537[ 7.576634] random: systemd: uninitialized urandom read (16 bytes read)
538[ 7.584896] systemd[1]: Created slice system-serial\x2dgetty.slice.
539[ OK ] Created slice system-serial\x2dgetty.slice.
540[ 7.619707] random: systemd: uninitialized urandom read (16 bytes read)
541[ 7.627928] systemd[1]: Created slice User and Session Slice.
542[ OK ] Created slice User and Session Slice.
543[ 7.656923] systemd[1]: Started Dispatch Password Requests to Console Dire
544ctory Watch.
545[ OK ] Started Dispatch Password …ts to Console Directory Watch.
546[ 7.697065] systemd[1]: Started Forward Password Requests to Wall Director
547y Watch.
548[ OK ] Started Forward Password R…uests to Wall Directory Watch.
549[ 7.740135] systemd[1]: Set up automount Arbitrary Executable File Formats
550 File System Automount Point.
551[ OK ] Set up automount Arbitrary…s File System Automount Point.
552[ 7.788079] systemd[1]: Reached target Local Encrypted Volumes.
553[ OK ] Reached target Local Encrypted Volumes.
554[ OK ] Reached target Paths.
555[ OK ] Reached target Remote Encrypted Volumes.
556[ OK ] Reached target Remote File Systems.
557[ OK ] Reached target Slices.
558[ OK ] Reached target Swap.
559[ OK ] Listening on Device-mapper event daemon FIFOs.
560[ OK ] Listening on Process Core Dump Socket.
561[ OK ] Listening on initctl Compatibility Named Pipe.
562[ OK ] Listening on Journal Socket (/dev/log).
563[ OK ] Listening on Journal Socket.
564[ OK ] Listening on Network Service Netlink Socket.
565[ OK ] Listening on udev Control Socket.
566[ OK ] Listening on udev Kernel Socket.
567 Mounting Huge Pages File System...
568 Mounting POSIX Message Queue File System...
569 Mounting Kernel Debug File System...
570 Mounting Temporary Directory (/tmp)...
571 Starting Create list of st…odes for the current kernel...
572 Mounting FUSE Control File System...
573 Mounting Kernel Configuration File System...
574 Starting Remount Root and Kernel File Systems...
575 Starting Apply Kernel Variables...
576 Starting udev Coldplug all Devices...
577[ OK ] Mounted Huge Pages File System.
578[ OK ] Mounted POSIX Message Queue File System.
579[ OK ] Mounted Kernel Debug File System.
580[ OK ] Mounted Temporary Directory (/tmp).
581[ OK ] Started Create list of sta… nodes for the current kernel.
582[ OK ] Mounted FUSE Control File System.
583[ OK ] Mounted Kernel Configuration File System.
584[ OK ] Started Remount Root and Kernel File Systems.
585[ OK ] Started Apply Kernel Variables.
586 Starting Load/Save Random Seed...
587 Starting Create Static Device Nodes in /dev...
588[ OK ] Started Create Static Device Nodes in /dev.
589[ OK ] Reached target Local File Systems (Pre).
590[ OK ] Reached target Local File Systems.
591[ OK ] Reached target Containers.
592[ OK ] Started Entropy Daemon based on the HAVEGE algorithm.
593 Starting Journal Service...
594 Starting udev Kernel Device Manager...
595[ OK ] Started udev Coldplug all Devices.
596[ OK ] Started Journal Service.
597[ OK ] Started udev Kernel Device Manager.
598 Starting Flush Journal to Persistent Storage...
599 Starting Network Service...
600[ 10.059415] systemd-journald[421]: Received client request to flush runtim
601e journal.
602[ OK ] Started Flush Journal to Persistent Storage.
603 Starting Create Volatile Files and Directories...
604[ OK ] Started Create Volatile Files and Directories.
605 Starting Network Time Synchronization...
606 Starting Update UTMP about System Boot/Shutdown...
607[ OK ] Started Update UTMP about System Boot/Shutdown.
608[ OK ] Found device /dev/ttyS0.
609[ 10.730027] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec,
610nowayout=0)
611[ 10.827912] sunxi_cedrus: module is from the staging directory, the qualit
612y is unknown, you have been warned.
613[ 10.840788] cedrus 1c0e000.video-codec: Device registered as /dev/video0
614[ 10.890023] lima 1c40000.gpu: bus rate = 200000000
615[ 10.894908] lima 1c40000.gpu: mod rate = 297000000
616[ OK [ 10.958710] input: axp20x-pek as /devices/platform/soc/1f03400.rsb/
617sunxi-rsb-3a3/axp221-pek/input/input0
618] Started Network Service.
619[ 10.958938] lima 1c40000.gpu: gp - mali400 version major 1 minor 1
620[ OK ] Reached target Network.
621[ 11.051905] cfg80211: Loading compiled-in X.509 certificates for regulator
622y database
623[ 11.065132] asoc-simple-card sound: sun8i <-> 1c22c00.dai mapping ok
624[ 11.078357] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1
625[ 11.091407] asoc-simple-card sound: ASoC: no DMI vendor name!
626[ 11.104454] lima 1c40000.gpu: pp1 - mali400 version major 1 minor 1
627[ 11.120477] lima 1c40000.gpu: l2 cache 64K, 4-way, 64byte cache line, 64bi
628t external bus
629[ 11.160978] [drm] Initialized lima 1.0.0 20190217 for 1c40000.gpu on minor
630 1
631[ 11.185227] random: crng init done
632[ 11.188690] random: 7 urandom warning(s) missed due to ratelimiting
633[ 11.283374] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
634[ 11.514798] platform regulatory.0: Direct firmware load for regulatory.db
635failed with error -2
636[ 11.523608] cfg80211: failed to load regulatory.db
637[ OK ] Reached target Sound Card.
638[ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
639[ 11.568702] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdi
640o for chip BCM43430/1
641[ 11.577640] usbcore: registered new interface driver brcmfmac
642[ OK ] Started Network Time Synchronization.
643[ 11.613874] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43
644430-sdio.sinovoip,bananapi-m64.txt failed with error -2
645[ 11.625737] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43
646430-sdio.txt failed with error -2
647[ OK ] Started Load/Save Random Seed.
648[ OK ] Reached target System Initialization.
649[ OK ] Started Daily Cleanup of Temporary Directories.
650[ OK ] Reached target System Time Set.
651[ OK ] Reached target System Time Synchronized.
652[ OK ] Started Daily verification of password and group files.
653[ OK ] Reached target Timers.
654[ OK ] Listening on D-Bus System Message Bus Socket.
655[ OK ] Reached target Sockets.
656[ OK ] Reached target Basic System.
657[ OK ] Started D-Bus System Message Bus.
658[ OK ] Started Pinebook Post Install..
659 Starting Login Service...
660 Starting Permit User Sessions...
661[ OK ] Started Permit User Sessions.
662[ OK ] Started Getty on tty1.
663[ OK ] Started Serial Getty on ttyS0.
664[ OK ] Reached target Login Prompts.
665[ 12.637051] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl
666 0x50
667[ OK ] Started Login Service.
668[ OK ] Reached target Multi-User System.
669[ OK ] Reached target Graphical Interface.
670
671Manjaro Linux 5.3.0-3-MANJARO-ARM (ttyS0)
672
673Manjaro-BPI-M64 login:
674Manjaro-BPI-M64 login:
675Manjaro-BPI-M64 login:
676Manjaro-BPI-M64 login: spiker
677Password:
678Welcome to Manjaro-ARM
679~~Website: https://manjaro.org
680~~Forum: https://forum.manjaro.org/c/manjaro-arm
681~~IRC: #manjaro-arm on irc.freenode.net
682~~Matrix: #manjaro-arm-public:matrix.org
683Last login: Wed Nov 6 16:56:00 on ttyS0
684[spiker@Manjaro-BPI-M64 ~]$
685[spiker@Manjaro-BPI-M64 ~]$
686[spiker@Manjaro-BPI-M64 ~]$ sudo shutdown now
687[sudo] password for spiker:
688 Stopping Session c1 of user spiker.
689[ OK ] Stopped target Graphical Interface.
690[ OK ] Stopped target Multi-User System.
691[ OK ] Stopped target Login Prompts.
692[ OK ] Stopped target Containers.
693[ OK ] Stopped target Remote Encrypted Volumes.
694[ OK ] Stopped target Sound Card.
695[ OK ] Stopped target Timers.
696[ OK ] Stopped [ OK ] Removed slice system-getty.slice.
697[ OK ] Stopped Serial Getty on ttyS0.
698[ OK ] Stopped Load/Save Random Seed.
699[ OK ] Stopped Session c1 of user spiker.
700[ OK ] Removed slice system-serial\x2dgetty.slice.
701 Stopping Login Service...
702 Stopping User Manager for UID 1000...
703[ OK ] Stopped User Manager for UID 1000.
704 Stopping User Runtime Directory /run/user/1000...
705[ OK ] Unmounted /run/user/1000.
706[ OK ] Stopped User Runtime Directory /run/user/1000.
707[ OK ] Removed slice User Slice of UID 1000.
708 Stopping D-Bus System Message Bus...
709 Stopping Permit User Sessions...
710[ OK ] Stopped D-Bus System Message Bus.
711[ OK ] Stopped Permit User Sessions.
712[ OK ] Stopped Login Service.
713[ OK ] Stopped target Basic System.
714[ OK ] Stopped target Network.
715[ OK ] Stopped target Paths.
716[ OK ] Stopped target Remote File Systems.
717[ OK ] Stopped target Slices.
718[ OK ] Removed slice User and Session Slice.
719[ OK ] Stopped target Sockets.
720[ OK ] Closed D-Bus System Message Bus Socket.
721[ OK ] Stopped target System Initialization.
722[ OK ] Stopped target Local Encrypted Volumes.
723[ OK ] Stopped Dispatch Password …ts to Console Directory Watch.
724[ OK ] Stopped Forward Password R…uests to Wall Directory Watch.
725 Stopping Network Service...
726 Stopping Network Time Synchronization...
727 Stopping Update UTMP about System Boot/Shutdown...
728[ OK ] Stopped Network Service.
729[ OK ] Stopped Network Time Synchronization.
730[ OK ] Started Generate shutdown-ramfs.
731[ OK ] Stopped Apply Kernel Variables.
732[ OK ] Stopped Update UTMP about System Boot/Shutdown.
733[ OK ] Stopped Create Volatile Files and Directories.
734[ OK ] Stopped target Local File Systems.
735[ OK ] Stopped target Local File Systems (Pre).
736 Unmounting Temporary Directory (/tmp)...
737[ OK ] Stopped Remount Root and Kernel File Systems.
738[ OK ] Stopped Create Static Device Nodes in /dev.
739[ OK ] Unmounted Temporary Directory (/tmp).
740[ OK ] Stopped target Swap.
741[ OK ] Reached target Shutdown.
742[ OK ] Reached target Unmount All Filesystems.
743[ OK ] Reached target Final Step.
744[ OK ] Started Power-Off.
745[ OK ] Reached target Power-Off.
746[ 502.444049] printk: systemd-shutdow: 51 output lines suppressed due to rat
747elimiting
748[ 502.484209] systemd-shutdown[1]: Syncing filesystems and block devices.
749[ 502.528972] systemd-shutdown[1]: Sending SIGTERM to remaining processes...
750[ 502.550075] systemd-journald[421]: Received SIGTERM from PID 1 (systemd-sh
751utdow).
752[ 502.561152] systemd-shutdown[1]: Sending SIGKILL to remaining processes...
753[ 502.578003] systemd-shutdown[1]: Unmounting file systems.
754[ 502.586137] [608]: Remounting '/' read-only in with options '(null)'.
755[ 502.604161] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
756[ 502.622414] systemd-shutdown[1]: All filesystems unmounted.
757[ 502.629064] systemd-shutdown[1]: Deactivating swaps.
758[ 502.634220] systemd-shutdown[1]: All swaps deactivated.
759[ 502.639510] systemd-shutdown[1]: Detaching loop devices.
760[ 502.645286] systemd-shutdown[1]: All loop devices detached.
761[ 502.651169] systemd-shutdown[1]: Detaching DM devices.
762[ 502.679534] printk: shutdown: 4 output lines suppressed due to ratelimitin
763g
764[ 502.723733] shutdown[1]: Syncing filesystems and block devices.
765[ 502.730109] shutdown[1]: Sending SIGTERM to remaining processes...
766[ 502.742363] shutdown[1]: Sending SIGKILL to remaining processes...
767[ 502.754275] shutdown[1]: Unmounting file systems.
768[ 502.761668] sd-umoun[611]: Unmounting '/oldroot/sys/kernel/config'.
769[ 502.771927] sd-umoun[612]: Unmounting '/oldroot/sys/fs/fuse/connections'.
770[ 502.781239] sd-umoun[613]: Unmounting '/oldroot/sys/kernel/debug'.
771[ 502.791369] sd-umoun[614]: Unmounting '/oldroot/dev/mqueue'.
772[ 502.799281] sd-umoun[615]: Unmounting '/oldroot/dev/hugepages'.
773[ 502.810836] sd-umoun[616]: Unmounting '/oldroot/sys/fs/cgroup/rdma'.
774[ 502.819882] sd-umoun[617]: Unmounting '/oldroot/sys/fs/cgroup/cpuset'.
775[ 502.832467] sd-umoun[618]: Unmounting '/oldroot/sys/fs/cgroup/freezer'.
776[ 502.842047] sd-umoun[619]: Unmounting '/oldroot/sys/fs/cgroup/memory'.
777[ 502.854279] sd-umoun[620]: Unmounting '/oldroot/sys/fs/cgroup/cpu,cpuacct'
778.
779[ 502.863772] sd-umoun[621]: Unmounting '/oldroot/sys/fs/cgroup/pids'.
780[ 502.875679] sd-umoun[622]: Unmounting '/oldroot/sys/fs/cgroup/hugetlb'.
781[ 502.884663] sd-umoun[623]: Unmounting '/oldroot/sys/fs/cgroup/perf_event'.
782[ 502.896939] sd-umoun[624]: Unmounting '/oldroot/sys/fs/cgroup/devices'.
783[ 502.906237] sd-umoun[625]: Unmounting '/oldroot/sys/fs/cgroup/blkio'.
784[ 502.918272] sd-umoun[626]: Unmounting '/oldroot/sys/fs/cgroup/net_cls,net_
785prio'.
786[ 502.928358] sd-umoun[627]: Unmounting '/oldroot/sys/fs/bpf'.
787[ 502.936463] sd-umoun[628]: Unmounting '/oldroot/sys/fs/pstore'.
788[ 502.945055] sd-umoun[629]: Unmounting '/oldroot/sys/fs/cgroup/systemd'.
789[ 502.954220] sd-umoun[630]: Unmounting '/oldroot/sys/fs/cgroup/unified'.
790[ 502.963606] sd-umoun[631]: Unmounting '/oldroot/sys/fs/cgroup'.
791[ 502.972138] sd-umoun[632]: Unmounting '/oldroot/run'.
792[ 502.982628] sd-umoun[633]: Unmounting '/oldroot/dev/pts'.
793[ 502.990734] sd-umoun[634]: Unmounting '/oldroot/dev/shm'.
794[ 503.000849] sd-umoun[635]: Unmounting '/oldroot/sys/kernel/security'.
795[ 503.009954] sd-umoun[636]: Unmounting '/oldroot/proc'.
796[ 503.017452] sd-umoun[637]: Unmounting '/oldroot/sys'.
797[ 503.027890] sd-umoun[638]: Unmounting '/oldroot/dev'.
798[ 503.035141] sd-umoun[639]: Unmounting '/oldroot'.
799[ 503.078156] shutdown[1]: All filesystems unmounted.
800[ 503.083040] shutdown[1]: Deactivating swaps.
801[ 503.089313] shutdown[1]: All swaps deactivated.
802[ 503.093844] shutdown[1]: Detaching loop devices.
803[ 503.098883] shutdown[1]: All loop devices detached.
804[ 503.103761] shutdown[1]: Detaching DM devices.
805[ 504.139142] kvm: exiting hardware virtualization
806[ 504.226490] reboot: Power down