· 6 years ago · Mar 25, 2020, 01:52 PM
1lava-dispatcher, installed at version: 2019.12
2start: 0 validate
3Start time: 2020-03-24 19:12:33.677943+00:00 (UTC)
4validate duration: 0.00
5case: validate
6case_id: 844
7definition: lava
8result: pass
9start: 1 minimal-boot (timeout 00:15:00) [common]
10start: 1.1 connect-device (timeout 00:15:00) [common]
11[common] connect-device Connecting to device using 'telnet ser2net 5001'
12end: 1.1 connect-device (duration 00:00:01) [common]
13start: 1.2 reset-device (timeout 00:14:59) [common]
14start: 1.2.1 send-reboot-commands (timeout 00:14:59) [common]
15reset
16reset
17send-reboot-commands: Wait for prompt The system is going down for reboot NOW (timeout 00:15:00)
18Trying 192.168.128.4...
19Connected to ser2net.
20Escape character is '^]'.
21reset
22#
23root@dragon�[ 242.419809] EXT4-fs (mmcblk0p10): re-mounted. Opts: data=ordered
24[ 244.970336] usb 1-1: USB disconnect, device number 2
25[ 245.387625] mmc0: Reset 0x1 never completed.
26[ 245.403826] reboot: Restarting system
27Format: Log Type - Time(microsec) - Message - Optional Info
28Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
29S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.0-00286
30S - IMAGE_VARIANT_STRING=HAAAANAZA
31S - OEM_IMAGE_VERSION_STRING=CRM
32S - Boot Config, 0x000002e1
33S - Core 0 Frequency, 0 MHz
34B - 1544 - PBL, Start
35B - 3489 - bootable_media_detect_entry, Start
36B - 126299 - bootable_media_detect_success, Start
37B - 126304 - elf_loader_entry, Start
38B - 128943 - auth_hash_seg_entry, Start
39B - 129153 - auth_hash_seg_exit, Start
40B - 144644 - elf_segs_hash_verify_entry, Start
41B - 205215 - PBL, End
42B - 211304 - SBL1, Start
43B - 273829 - pm_device_init, Start
44D - 14670 - pm_device_init, Delta
45B - 288957 - boot_flash_init, Start
46D - 30 - boot_flash_init, Delta
47B - 292952 - boot_config_data_table_init, Start
48D - 57645 - boot_config_data_table_init, Delta - (452 Bytes)
49B - 355172 - CDT version:3,Platform ID:24,Major ID:1,Minor ID:0,Subtype:0
50B - 361394 - sbl1_ddr_set_params, Start
51B - 365207 - cpr_init, Start
52D - 0 - cpr_init, Delta
53B - 370819 - Pre_DDR_clock_init, Start
54D - 213 - Pre_DDR_clock_init, Delta
55D - 0 - sbl1_ddr_set_params, Delta
56B - 383446 - pm_driver_init, Start
57D - 3507 - pm_driver_init, Delta
58B - 395554 - SBC platform detected: XO_ADJ_FINE = 0x20
59B - 395585 - clock_init, Start
60D - 30 - clock_init, Delta
61B - 410499 - Image Load, Start
62D - 32818 - QSEE Image Loaded, Delta - (567468 Bytes)
63B - 443317 - Image Load, Start
64D - 396 - SEC Image Loaded, Delta - (2048 Bytes)
65B - 450546 - sbl1_efs_handle_cookies, Start
66D - 91 - sbl1_efs_handle_cookies, Delta
67B - 458323 - Image Load, Start
68D - 20222 - QHEE Image Loaded, Delta - (56048 Bytes)
69B - 478575 - Image Load, Start
70D - 14152 - RPM Image Loaded, Delta - (149316 Bytes)
71B - 492758 - Image Load, Start
72D - 30957 - APPSBL Image Loaded, Delta - (519376 Bytes)
73B - 523715 - QSEE Execution, Start
74D - 61 - QSEE Execution, Delta
75B - 529419 - SBL1, End
76D - 320463 - SBL1, Delta
77S - Flash Throughput, 90000 KB/s (1294708 Bytes, 14304 us)
78S - DDR Frequency, 400 MHz
79Android Bootloader - UART_DM Initialized!!!
80[0] [0] BUILD_VERSION=
81[0] [0] BUILD_DATE=17:49:16 - May 5 2017
82[0] [0] welcome to lk
83[10] [10] platform_init()
84[10] [10] target_init()
85[50] [50] SDHC Running in HS200 mode
86[70] [70] Done initialization of the card
87[80] [80] pm8x41_get_is_cold_boot: cold boot
88[90] [90] Neither 'config' nor 'frp' partition found
89[90] [90] Not able to search the panel:
90[100] [100] Display not enabled for 24 HW type
91[100] [100] Target panel init not found!
92[100] [100] pm8x41_get_is_cold_boot: cold boot
93[110] [110] partition misc doesn't exist
94[110] [110] error in emmc_recovery_init
95[110] [110] Unable to locate /bootselect partition
96[120] [120] No 'misc' partition found
97[120] [120] Error reading MISC partition
98[130] [130] failed to get ffbm cookie[130] [130] Loading boot image (14034944): start
99[230] [230] Loading boot image (14034944): done
100[240] [240] use_signed_kernel=0, is_unlocked=0, is_tampered=0.
101[250] [250] DTB Total entry: 5, DTB version: 2
102[260] [260] Using DTB entry 0x000000f7/00000000/0x00010018/0 for device 0x000000f7/00010000/0x00010018/0
103[270] [270] Using pmic info 0x2000b/0x0/0x0/0x0 for device 0x2000b/0x0/0x0/0x0
104[270] [270] target_display_panel_node:510: hw_id=24 panel_name=\"\"
105[280] [280] cmdline: root=/dev/mmcblk0p10 rw rootwait console=ttyMSM0,115200n8 androidboot.emmc=true androidboot.serialno=25e12e08 androidboot.baseband=apq mdss_mdp.panel=0:dsi:0:
106[290] [290] Updating device tree: start
107[390] [390] Updating device tree: done
108[400] [400] booting linux @ 0x80080000, ramdisk @ 0x82000000 (22), tags/device tree @ 0x81e00000
109[400] [400] Jumping to kernel via monitor
110[ 0.000000] Booting Linux on physical CPU 0x0
111[ 0.000000] Initializing cgroup subsys cpu
112[ 0.000000] Initializing cgroup subsys cpuacct
113Using line separator: #'\n'#
114Waiting for the login prompt
115Parsing kernel messages
116['-+\\[ cut here \\]-+\\s+(.*\\s+-+\\[ end trace (\\w*) \\]-+)', '(Unhandled fault.*)\\r\\n', 'Kernel panic - (.*) end Kernel panic', 'Stack:\\s+(.*\\s+-+\\[ end trace (\\w*) \\]-+)', 'root@dragonboard-410c:~#', '.* login:', 'Login incorrect']
117[auto-login-action] Waiting for messages, (timeout 00:14:41)
118[ 0.000000] Linux version 4.2.0+linaro (maciej@lab) (gcc version 5.2.0 (GCC) ) #1 SMP PREEMPT Mon Jun 19 12:14:02 CEST 2017
119[ 0.000000] CPU: AArch64 Processor [410fd030] revision 0
120[ 0.000000] Detected VIPT I-cache on CPU0
121[ 0.000000] alternatives: enabling workaround for ARM errata 826319, 827319, 824069
122[ 0.000000] alternatives: enabling workaround for ARM erratum 845719
123[ 0.000000] efi: Getting EFI parameters from FDT:
124[ 0.000000] efi: UEFI not found.
125[ 0.000000] cma: Reserved 64 MiB at 0x00000000bc000000
126[ 0.000000] PERCPU: Embedded 16 pages/cpu @ffffffc03bf5a000 s26880 r8192 d30464 u65536
127[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 252416
128[ 0.000000] Kernel command line: root=/dev/mmcblk0p10 rw rootwait console=ttyMSM0,115200n8 androidboot.emmc=true androidboot.serialno=25e12e08 androidboot.baseband=apq mdss_mdp.panel=0:dsi:0:
129[ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes
130[ 0.000000] log_buf_len total cpu_extra contributions: 12288 bytes
131[ 0.000000] log_buf_len min size: 16384 bytes
132[ 0.000000] log_buf_len: 32768 bytes
133[ 0.000000] early log buf free: 14788(90%)
134[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
135[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
136[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
137[ 0.000000] software IO TLB [mem 0xb6c00000-0xbac00000] (64MB) mapped at [ffffffc036c00000-ffffffc03abfffff]
138[ 0.000000] Memory: 848872K/1026048K available (8763K kernel code, 779K rwdata, 3596K rodata, 480K init, 13307K bss, 111640K reserved, 65536K cma-reserved)
139[ 0.000000] Virtual kernel memory layout:
140[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB)
141[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
142[ 0.000000] 0xffffffbdc2000000 - 0xffffffbdc3000000 ( 16 MB actual)
143[ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB)
144[ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB)
145[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
146[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc040000000 ( 1024 MB)
147[ 0.000000] .init : 0xffffffc000c94000 - 0xffffffc000d0c000 ( 480 KB)
148[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc000c93fd4 ( 12368 KB)
149[ 0.000000] .data : 0xffffffc000d13000 - 0xffffffc000dd5e00 ( 780 KB)
150[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
151[ 0.000000] Running RCU self tests
152[ 0.000000] Preemptible hierarchical RCU implementation.
153[ 0.000000] RCU lockdep checking is enabled.
154[ 0.000000] Additional per-CPU info printed with stalls.
155[ 0.000000] Build-time adjustment of leaf fanout to 64.
156[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
157[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
158[ 0.000000] NR_IRQS:64 nr_irqs:64 0
159[ 0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
160[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
161[ 0.000004] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
162[ 0.000341] Console: colour dummy device 80x25
163[ 0.000364] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
164[ 0.000372] ... MAX_LOCKDEP_SUBCLASSES: 8
165[ 0.000379] ... MAX_LOCK_DEPTH: 48
166[ 0.000386] ... MAX_LOCKDEP_KEYS: 8191
167[ 0.000393] ... CLASSHASH_SIZE: 4096
168[ 0.000401] ... MAX_LOCKDEP_ENTRIES: 32768
169[ 0.000407] ... MAX_LOCKDEP_CHAINS: 65536
170[ 0.000414] ... CHAINHASH_SIZE: 32768
171[ 0.000421] memory used by lock dependency info: 8159 kB
172[ 0.000429] per task-struct memory footprint: 1920 bytes
173[ 0.000451] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
174[ 0.000465] pid_max: default: 32768 minimum: 301
175[ 0.000706] Security Framework initialized
176[ 0.000803] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
177[ 0.000815] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
178[ 0.002317] Initializing cgroup subsys blkio
179[ 0.002360] Initializing cgroup subsys memory
180[ 0.002425] Initializing cgroup subsys devices
181[ 0.002467] Initializing cgroup subsys hugetlb
182[ 0.003228] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
183[ 0.003286] EFI services will not be available.
184[ 0.040779] CPU1: Booted secondary processor
185[ 0.040795] Detected VIPT I-cache on CPU1
186[ 0.050577] CPU2: Booted secondary processor
187[ 0.050592] Detected VIPT I-cache on CPU2
188[ 0.060622] CPU3: Booted secondary processor
189[ 0.060638] Detected VIPT I-cache on CPU3
190[ 0.060839] Brought up 4 CPUs
191[ 0.060868] SMP: Total of 4 processors activated.
192[ 0.060876] CPU: All CPU(s) started at EL1
193[ 0.061037] alternatives: patching kernel code
194[ 0.062988] devtmpfs: initialized
195[ 0.101029] DMI not present or invalid.
196[ 0.102149] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
197[ 0.104994] pinctrl core: initialized pinctrl subsystem
198[ 0.108860] NET: Registered protocol family 16
199[ 0.150096] cpuidle: using governor ladder
200[ 0.180094] cpuidle: using governor menu
201[ 0.180401] vdso: 2 pages (1 code @ ffffffc000d19000, 1 data @ ffffffc000d18000)
202[ 0.180500] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
203[ 0.183320] DMA: preallocated 256 KiB pool for atomic allocations
204[ 0.183953] Serial: AMBA PL011 UART driver
205[ 0.193518] qcom-smd soc:smd: new channel 'rpm_requests' info-size: 88 fifo-size: 1024
206[ 0.222120] irq: no irq domain found for /soc/wcnss-smp2p/slave-kernel !
207[ 0.226252] irq: no irq domain found for /soc/qcom,mdss_mdp@1a00000 !
208[ 0.305535] msm_iommu 1f00000.qcom,iommu: invalid resource
209[ 0.305692] msm_iommu 1f00000.qcom,iommu: iface: 0, core: 0
210[ 0.305771] msm_iommu 1f00000.qcom,iommu: device gfx_iommu (model: 500) mapped at ffffff80003a0000, with 2 ctx banks
211[ 0.306022] genirq: Setting trigger mode 1 for irq 155 failed (gic_set_type+0x0/0x48)
212[ 0.306299] msm_iommu 1f00000.qcom,iommu: Request Global CFG IRQ 155 failed with ret=-22
213[ 0.307805] msm_iommu 1e00000.qcom,iommu: iface: 0, core: 0
214[ 0.307877] msm_iommu 1e00000.qcom,iommu: device apps_iommu (model: 500) mapped at ffffff8000680000, with 20 ctx banks
215[ 0.308124] genirq: Setting trigger mode 1 for irq 155 failed (gic_set_type+0x0/0x48)
216[ 0.308227] msm_iommu 1e00000.qcom,iommu: Request Global CFG IRQ 155 failed with ret=-22
217[ 0.320237] msm_iommu_ctx 1f09000.qcom,iommu-ctx: context gfx3d_user using bank 1
218[ 0.320697] msm_iommu_ctx 1f0a000.qcom,iommu-ctx: context gfx3d_priv using bank 2
219[ 0.321133] msm_iommu_ctx 1e22000.qcom,iommu-ctx: context jpeg_enc0 using bank 2
220[ 0.321758] msm_iommu_ctx 1e23000.qcom,iommu-ctx: context vfe using bank 3
221[ 0.322120] msm_iommu_ctx 1e24000.qcom,iommu-ctx: context mdp_0 using bank 4
222[ 0.322468] msm_iommu_ctx 1e25000.venus_ns: context venus_ns using bank 5
223[ 0.322818] msm_iommu_ctx 1e26000.qcom,iommu-ctx: context cpp using bank 6
224[ 0.323161] msm_iommu_ctx 1e27000.qcom,iommu-ctx: context mDSP using bank 7
225[ 0.323504] msm_iommu_ctx 1e28000.qcom,iommu-ctx: context gss using bank 8
226[ 0.323852] msm_iommu_ctx 1e29000.qcom,iommu-ctx: context a2 using bank 9
227[ 0.324219] msm_iommu_ctx 1e32000.qcom,iommu-ctx: context mdp_1 using bank 18
228[ 0.324567] msm_iommu_ctx 1e33000.venus_sec_pixel: context venus_sec_pixel using bank 19
229[ 0.324911] msm_iommu_ctx 1e34000.venus_sec_bitstream: context venus_sec_bitstream using bank 20
230[ 0.325255] msm_iommu_ctx 1e35000.venus_sec_non_pixel: context venus_sec_non_pixel using bank 21
231[ 0.325601] msm_iommu_ctx 1e36000.qcom,iommu-ctx: context venus_fw using bank 22
232[ 0.325959] msm_iommu_ctx 1e37000.qcom,iommu-ctx: context periph_rpm using bank 23
233[ 0.326303] msm_iommu_ctx 1e38000.qcom,iommu-ctx: context periph_CE using bank 24
234[ 0.326650] msm_iommu_ctx 1e39000.qcom,iommu-ctx: context periph_BLSP using bank 25
235[ 0.326991] msm_iommu_ctx 1e3a000.qcom,iommu-ctx: context periph_SDC1 using bank 26
236[ 0.327334] msm_iommu_ctx 1e3b000.qcom,iommu-ctx: context periph_SDC2 using bank 27
237[ 0.327675] msm_iommu_ctx 1e3c000.qcom,iommu-ctx: context periph_audio using bank 28
238[ 0.328021] msm_iommu_ctx 1e3d000.qcom,iommu-ctx: context periph_USB_HS1 using bank 29
239[ 0.328638] qcom_iommu: iommu sec: psize[0]: 94208, psize[1]: 0
240[ 0.329997] vgaarb: loaded
241[ 0.330568] SCSI subsystem initialized
242[ 0.332152] usbcore: registered new interface driver usbfs
243[ 0.332292] usbcore: registered new interface driver hub
244[ 0.332512] usbcore: registered new device driver usb
245[ 0.332823] Linux video capture interface: v2.00
246[ 0.333247] dmi: Firmware registration failed.
247[ 0.334049] Advanced Linux Sound Architecture Driver Initialized.
248[ 0.335993] Bluetooth: Core ver 2.20
249[ 0.336089] NET: Registered protocol family 31
250[ 0.336099] Bluetooth: HCI device and connection manager initialized
251[ 0.336158] Bluetooth: HCI socket layer initialized
252[ 0.336178] Bluetooth: L2CAP socket layer initialized
253[ 0.336303] Bluetooth: SCO socket layer initialized
254[ 0.338468] clocksource: Switched to clocksource arch_sys_counter
255[ 0.362869] NET: Registered protocol family 2
256[ 0.364302] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
257[ 0.364421] TCP bind hash table entries: 8192 (order: 7, 524288 bytes)
258[ 0.366731] TCP: Hash tables configured (established 8192 bind 8192)
259[ 0.366894] UDP hash table entries: 512 (order: 4, 81920 bytes)
260[ 0.367215] UDP-Lite hash table entries: 512 (order: 4, 81920 bytes)
261[ 0.368177] NET: Registered protocol family 1
262[ 0.369053] RPC: Registered named UNIX socket transport module.
263[ 0.369065] RPC: Registered udp transport module.
264[ 0.369074] RPC: Registered tcp transport module.
265[ 0.369082] RPC: Registered tcp NFSv4.1 backchannel transport module.
266[ 0.369752] Unpacking initramfs...
267[ 0.369771] Initramfs unpacking failed: junk in compressed archive
268[ 0.370577] kvm [1]: HYP mode not available
269[ 0.374850] futex hash table entries: 1024 (order: 5, 131072 bytes)
270[ 0.375256] audit: initializing netlink subsys (disabled)
271[ 0.375430] audit: type=2000 audit(0.359:1): initialized
272[ 0.376956] HugeTLB registered 2 MB page size, pre-allocated 0 pages
273[ 0.410899] VFS: Disk quotas dquot_6.6.0
274[ 0.411492] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
275[ 0.423910] NFS: Registering the id_resolver key type
276[ 0.424148] Key type id_resolver registered
277[ 0.424159] Key type id_legacy registered
278[ 0.424663] fuse init (API version 7.23)
279[ 0.425914] 9p: Installing v9fs 9p2000 file system support
280[ 0.432218] io scheduler noop registered
281[ 0.433301] io scheduler cfq registered (default)
282[ 0.453898] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
283[ 0.458705] msm_serial 78af000.serial: msm_serial: detected port #1
284[ 0.458888] msm_serial 78af000.serial: uartclk = 3686400
285[ 0.459017] 78af000.serial: ttyMSM1 at MMIO 0x78af000 (irq = 132, base_baud = 230400) is a MSM
286[ 0.460525] msm_serial 78b0000.serial: msm_serial: detected port #0
287[ 0.460659] msm_serial 78b0000.serial: uartclk = 3686400
288[ 0.460743] 78b0000.serial: ttyMSM0 at MMIO 0x78b0000 (irq = 133, base_baud = 230400) is a MSM
289[ 0.460782] msm_serial: console setup on port #0
290[ 1.508800] console [ttyMSM0] enabled
291[ 1.514310] msm_serial: driver initialized
292[ 1.519460] [drm] Initialized drm 1.1.0 20060810
293[ 1.521479] msm_dsi_phy 1a98300.qcom,mdss_dsi_phy: Failed to get supply 'vddio': -517
294[ 1.525555] msm_dsi_phy 1a98300.qcom,mdss_dsi_phy: dsi_phy_regulator_init: failed to init regulator, ret=-517
295[ 1.533310] msm_dsi_phy 1a98300.qcom,mdss_dsi_phy: dsi_phy_driver_probe: failed to init regulator
296[ 1.550702] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
297[ 1.552719] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
298[ 1.559400] msm_dsi 1a98000.qcom,mdss_dsi: Failed to get supply 'vdd': -517
299[ 1.566504] dsi_regulator_init: failed to init regulator, ret=-517
300[ 1.573226] msm_dsi_host_init: regulator init failed
301[ 1.579547] msm 1a00000.qcom,mdss_mdp: failed to bind 1a98000.qcom,mdss_dsi (ops dsi_ops): -517
302[ 1.588419] msm 1a00000.qcom,mdss_mdp: master bind failed: -517
303[ 1.612951] loop: module loaded
304[ 1.630604] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
305[ 1.653441] tun: Universal TUN/TAP device driver, 1.6
306[ 1.653467] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
307[ 1.658683] sky2: driver version 1.30
308[ 1.664524] usbcore: registered new interface driver asix
309[ 1.667396] usbcore: registered new interface driver ax88179_178a
310[ 1.672816] usbcore: registered new interface driver cdc_ether
311[ 1.678868] usbcore: registered new interface driver dm9601
312[ 1.684576] usbcore: registered new interface driver net1080
313[ 1.690057] usbcore: registered new interface driver plusb
314[ 1.695940] usbcore: registered new interface driver cdc_subset
315[ 1.701259] usbcore: registered new interface driver zaurus
316[ 1.707114] usbcore: registered new interface driver cdc_ncm
317[ 1.716063] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
318[ 1.718484] ehci-pci: EHCI PCI platform driver
319[ 1.724870] ehci-platform: EHCI generic platform driver
320[ 1.729651] ehci-msm: Qualcomm On-Chip EHCI Host Controller
321[ 1.734724] msm_hsusb_host 78d9000.ehci: unable to find transceiver
322[ 1.740237] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
323[ 1.746134] ohci-pci: OHCI PCI platform driver
324[ 1.752492] ohci-platform: OHCI generic platform driver
325[ 1.757293] usbcore: registered new interface driver cdc_acm
326[ 1.761917] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
327[ 1.767958] usbcore: registered new interface driver usblp
328[ 1.775649] usbcore: registered new interface driver cdc_wdm
329[ 1.781206] usbcore: registered new interface driver uas
330[ 1.787045] usbcore: registered new interface driver usb-storage
331[ 1.792446] usbcore: registered new interface driver usbserial
332[ 1.798260] usbcore: registered new interface driver usbserial_generic
333[ 1.804256] usbserial: USB Serial support registered for generic
334[ 1.821155] usb3503 usb2513: switched to HUB mode
335[ 1.821180] usb3503 usb2513: usb3503_probe: probed in hub mode
336[ 1.827389] usbip_core: USB/IP Core v1.0.0
337[ 1.830711] usbcore: registered new device driver usbip-host
338[ 1.834661] usbip_host: USB/IP Host Driver v1.0.0
339[ 1.841661] mousedev: PS/2 mouse device common for all mice
340[ 1.847603] input: pm8941_pwrkey as /devices/platform/soc/200f000.spmi/spmi-0/0-00/200f000.spmi:pm8916@0:pwrkey@800/input/input0
341[ 1.852428] i2c /dev entries driver
342[ 1.863137] i2c_qup 78b6000.i2c:
343[ 1.863137] tx channel not available
344[ 1.867932] i2c_qup 78b8000.i2c:
345[ 1.867932] tx channel not available
346[ 1.873877] i2c_qup 78ba000.i2c:
347[ 1.873877] tx channel not available
348[ 1.882638] l3: supplied by s3
349[ 1.889863] qcom-tsens 4a8000.thermal-sensor: tsens calibration failed
350[ 1.890519] Bluetooth: HCI UART driver ver 2.3
351[ 1.895925] Bluetooth: HCI UART protocol H4 registered
352[ 1.900383] Bluetooth: HCI UART protocol BCSP registered
353[ 1.905470] Bluetooth: HCI UART protocol Three-wire (H5) registered
354[ 1.911147] usbcore: registered new interface driver btusb
355[ 1.917507] sdhci: Secure Digital Host Controller Interface driver
356[ 1.922515] sdhci: Copyright(c) Pierre Ossman
357[ 1.928768] sdhci-pltfm: SDHCI platform and OF driver helper
358[ 1.940921] l5: supplied by s4
359[ 1.941233] sdhci_msm 7824900.sdhci: Failed getting OCR mask: 0
360[ 1.988510] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
361[ 1.989743] sdhci_msm 7864900.sdhci: Got CD GPIO
362[ 2.002632] sdhci_msm 7864900.sdhci: Failed getting OCR mask: 0
363[ 2.055889] mmc0: MAN_BKOPS_EN bit is not set
364[ 2.058789] mmc1: SDHCI controller on 7864900.sdhci [7864900.sdhci] using ADMA 64-bit
365[ 2.063943] ledtrig-cpu: registered to indicate activity on CPUs
366[ 2.067279] mmc0: new high speed MMC card at address 0001
367[ 2.068561] usbcore: registered new interface driver usbhid
368[ 2.068565] usbhid: USB HID core driver
369[ 2.074315] l7: supplied by s4
370[ 2.075855] qcom-tz-pil soc:pronto_rproc: Found relocation area 6291456@0x000000008b600000
371[ 2.075975] remoteproc0: soc:pronto_rproc is available
372[ 2.075979] remoteproc0: Note: remoteproc is still under development and considered experimental.
373[ 2.075984] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
374[ 2.076535] remoteproc0: Direct firmware load for wcnss.mdt failed with error -2
375[ 2.076547] remoteproc0: failed to load soc:pronto_rproc
376[ 2.076782] qcom-tz-pil soc:vidc_tzpil@0: no crash reason id
377[ 2.077032] soc:vidc_tzpil@0 supply qcom,pll not found, using dummy regulator
378[ 2.077171] qcom-tz-pil soc:vidc_tzpil@0: failed to read qcom,pll_uV, skipping
379[ 2.077178] qcom-tz-pil soc:vidc_tzpil@0: failed to read qcom,pll_uA, skipping
380[ 2.077187] qcom-tz-pil soc:vidc_tzpil@0: no wdog IRQ defined
381[ 2.077194] qcom-tz-pil soc:vidc_tzpil@0: no fatal IRQ defined
382[ 2.077201] qcom-tz-pil soc:vidc_tzpil@0: no ready IRQ defined
383[ 2.077208] qcom-tz-pil soc:vidc_tzpil@0: no handover IRQ defined
384[ 2.077216] qcom-tz-pil soc:vidc_tzpil@0: no stop-ack IRQ defined
385[ 2.077277] qcom-tz-pil soc:vidc_tzpil@0: Found relocation area 8388608@0x000000008f800000
386[ 2.077396] remoteproc1: soc:vidc_tzpil@0 is available
387[ 2.077401] remoteproc1: Note: remoteproc is still under development and considered experimental.
388[ 2.077405] remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
389[ 2.077702] remoteproc1: Direct firmware load for venus.mdt failed with error -2
390[ 2.077712] remoteproc1: failed to load soc:vidc_tzpil@0
391[ 2.084559] usbcore: registered new interface driver snd-usb-audio
392[ 2.086387] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
393[ 2.086467] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
394[ 2.086557] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
395[ 2.086656] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
396[ 2.088860] qcom-apq8016-sbc 7702000.sound: error getting codec dai name
397[ 2.088867] qcom-apq8016-sbc 7702000.sound: Error resolving dai links: -517
398[ 2.091968] NET: Registered protocol family 10
399[ 2.095061] sit: IPv6 over IPv4 tunneling driver
400[ 2.096626] NET: Registered protocol family 17
401[ 2.096814] Bluetooth: RFCOMM TTY layer initialized
402[ 2.096832] Bluetooth: RFCOMM socket layer initialized
403[ 2.096868] Bluetooth: RFCOMM ver 1.11
404[ 2.096903] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
405[ 2.097029] Bluetooth: HIDP socket layer initialized
406[ 2.097341] 9pnet: Installing 9P2000 support
407[ 2.097543] Key type dns_resolver registered
408[ 2.099490] registered taskstats version 1
409[ 2.101270] l6: supplied by s4
410[ 2.108113] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
411[ 2.109035] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
412[ 2.109420] l2: supplied by s3
413[ 2.139529] msm 1a00000.qcom,mdss_mdp: bound 1a98000.qcom,mdss_dsi (ops dsi_ops)
414[ 2.139575] msm 1a00000.qcom,mdss_mdp: bound 1c00000.qcom,adreno-3xx (ops a3xx_ops)
415[ 2.139670] 1a00000.qcom,mdss_mdp supply vdd not found, using dummy regulator
416[ 2.158621] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
417[ 2.158625] [drm] No driver support for vblank timestamp query.
418[ 2.160669] msm 1a00000.qcom,mdss_mdp: No connectors reported connected with modes
419[ 2.160686] [drm] Cannot find any crtc or sizes - going 1024x768
420[ 2.417117] mmcblk0: mmc0:0001 DS1008 7.28 GiB
421[ 2.417410] mmcblk0boot0: mmc0:0001 DS1008 partition 1 4.00 MiB
422[ 2.417667] mmcblk0boot1: mmc0:0001 DS1008 partition 2 4.00 MiB
423[ 2.417928] mmcblk0rpmb: mmc0:0001 DS1008 partition 3 4.00 MiB
424[ 2.429944] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10
425[ 2.432157] Console: switching to colour frame buffer device 128x48
426[ 2.472617] msm 1a00000.qcom,mdss_mdp: fb0: msm frame buffer device
427[ 2.478569] msm 1a00000.qcom,mdss_mdp: registered panic notifier
428[ 2.518576] [drm] Initialized msm 1.0.0 20130625 on minor 0
429[ 2.519761] msm_otg 78d9000.phy: OTG regs = ffffff800050a000
430[ 2.523385] msm_otg 78d9000.phy: no vddcx
431[ 2.639511] msm_hsusb_host 78d9000.ehci: EHCI Host Controller
432[ 2.641581] msm_hsusb_host 78d9000.ehci: new USB bus registered, assigned bus number 1
433[ 2.645465] msm_hsusb_host 78d9000.ehci: irq 144, io mem 0x078d9000
434[ 2.664456] CPR closed loop is enabled
435[ 2.665240] CPR is enabled!
436[ 2.668527] msm_hsusb_host 78d9000.ehci: USB 2.0 started, EHCI 1.00
437[ 2.671263] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
438[ 2.676035] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
439[ 2.683014] usb usb1: Product: EHCI Host Controller
440[ 2.683186] qcom-apq8016-sbc 7702000.sound: adv7511 <-> Quatenary MI2S mapping ok
441[ 2.688537] input: gpio_keys as /devices/platform/gpio_keys/input/input1
442[ 2.689188] hctosys: unable to open rtc device (rtc0)
443[ 2.709292] usb usb1: Manufacturer: Linux 4.2.0+linaro ehci_hcd
444[ 2.713733] ALSA device list:
445[ 2.713737] #0: DB410c
446[ 2.7230[ 2.727799] hub 1-0:1.0: USB hub found
447[ 2.728003] hub 1-0:1.0: 1 port detected
448[ 2.737225] EXT3-fs (mmcblk0p10): error: couldn't mount because of unsupported optional features (240)
449[ 2.738627] EXT2-fs (mmcblk0p10): error: couldn't mount because of unsupported optional features (240)
450[ 2.759957] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: (null)
451[ 2.760040] VFS: Mounted root (ext4 filesystem) on device 179:10.
452[ 2.777596] devtmpfs: mounted
453[ 2.777953] Freeing unused kernel memory: 480K (ffffffc000c94000 - ffffffc000d0c000)
454[ 2.779578] Freeing alternatives memory: 16K (ffffffc000d0c000 - ffffffc000d10000)
455INIT: version 2.88 booting
456[ 3.048587] usb 1-1: new high-speed USB device number 2 using msm_hsusb_host
457Starting udev
458[ 3.199668] usb 1-1: New USB device found, idVendor=0424, idProduct=2513
459[ 3.199708] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
460[ 3.211993] hub 1-1:1.0: USB hub found
461[ 3.212678] hub 1-1:1.0: 3 ports detected
462[ 3.489611] udevd[1159]: starting version 182
463[ 3.765527] EXT4-fs (mmcblk0p10): re-mounted. Opts: data=ordered
464[ 3.868486] iris_read_v: 0x0
465[ 3.868518] wcnss: IRIS Reg: 0x51120004
466[ 3.871414] random: dd urandom read with 12 bits of entropy available
467[ 4.078896] remoteproc0: powering up soc:pronto_rproc
468[ 4.083948] remoteproc0: Booting fw image wcnss.mdt, size 7260
469hwclock: can't open '/dev/misc/rtc': No such file or directory
470Mon Jun 19 14:02:10 UTC 2017
471hwclock: can't open '/dev/misc/rtc': No such file or directory or directory
472Mon Jun 19 14:02:10 UTC 2017
473hwclock: can't open '/dev/misc/rtc': No such file or directory
474[ 4.479278] qcom-smd soc:smd: new channel 'IPCRTR' info-size: 40 fifo-size: 8192
475INIT: Entering runlevel: 5[ 4.693194] qcom-tz-pil soc:pronto_rproc: start successful
476[ 4.709977] qcom-smd soc:smd: new channel 'APPS_RIVA_CTRL' info-size: 40 fifo-size: 8192
477[ 4.710082] qcom-smd soc:smd: new channel 'APPS_RIVA_DATA' info-size: 40 fifo-size: 8192
478[ 4.735635] qcom-smd soc:smd: new channel 'WCNSS_CTRL' info-size: 40 fifo-size: 8192
479[ 4.735742] qcom-smd soc:smd: new channel 'WLAN_CTRL' info-size: 40 fifo-size: 8192
480[ 4.746397] qcom_smd_wlan_ctrl_probe: enter
481Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device
482Starting system message bus: dbus.
483Starting Connection Manager
484Starting Xserver
485Starting Dropbear SSH server:
486dropbear.
487hwclock: can't open '/dev/misc/rtc': No such file or directory
488Starting syslogd/klogd: done
489Starting Telephony daemon
490X.Org X Server 1.17.2
491Release Date: 2015-06-16
492X Protocol Version 11, Revision 0
493Build Operating System: Linux 3.16.0-30-generic x86_64
494Current Operating System: Linux dragonboard-410c 4.2.0+linaro #1 SMP PREEMPT Mon Jun 19 12:14:02 CEST 2017 aarch64
495Kernel command line: root=/dev/mmcblk0p10 rw rootwait console=ttyMSM0,115200n8 androidboot.emmc=true androidboot.serialno=25e12e08 androidboot.baseband=apq mdss_mdp.panel=0:dsi:0:
496Build Date: 19 June 2017 12:01:01PM
497
498Current version of pixman: 0.32.6
499 Before reporting problems, check http://wiki.x.org
500 to make sure that you have the latest version.[ 5.469334] 1c00000.qcom,adreno-3xx supply vdd not found, using dummy regulator
501Markers: (--) probed, (**) from config file, (==) default setting,
502 (++) from command line, (!!) notice, (II) informational,
503 (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
504(==) Log file: \"/var/log/Xorg.0.log\", Time: Mon Jun 19 14:02:11 2017
505(==) Using system config directory \"/usr/share/X11/xorg.conf.d\"[ 5.508059] msm 1a00000.qcom,mdss_mdp: A306: using IOMMU
506[ 5.543104] adreno 1c00000.qcom,adreno-3xx: couldn't get gfx3d1_user context
507[ 5.543198] adreno 1c00000.qcom,adreno-3xx: couldn't get gfx3d1_priv context
508Poky (Yocto Project Reference Distro) 2.0 dragonboard-410c /dev/ttyMSM0
509dragonboard-410c login: [ 6.047473] fw_status: 2
510[ 6.096893] qcom-smd soc:smd: new channel 'APPS_RIVA_BT_CMD' info-size: 40 fifo-size: 8192
511[ 6.097024] qcom-smd soc:smd: new channel 'APPS_RIVA_BT_ACL' info-size: 40 fifo-size: 8192
512[ 6.104252] qcom-smd soc:smd: new channel 'APPS_RIVA_ANT_CMD' info-size: 40 fifo-size: 1024
513[ 6.113010] qcom-smd soc:smd: new channel 'APPS_RIVA_ANT_DATA' info-size: 40 fifo-size: 2048
514[ 6.122839] qcom-smd soc:smd: new channel 'APPS_FM' info-size: 40 fifo-size: 8192
515D-BUS per-session daemon address is: unix:abstract=/tmp/dbus-2uGZ3FxSNx,guid=e90e2ca8f88e12d5e6f74ce05947d964
516Connection closed by foreign host.
517wait for prompt timed out
518end: 1.2.1 send-reboot-commands (duration 09:31:36) [common]
519case: send-reboot-commands
520case_id: 845
521definition: lava
522duration: 34296.26
523extra: ...
524level: 1.2.1
525namespace: common
526result: fail
527wait for prompt timed out
528end: 1.2 reset-device (duration 09:31:36) [common]
529case: reset-device
530case_id: 846
531definition: lava
532duration: 34296.26
533extra: ...
534level: 1.2
535namespace: common
536result: fail
537minimal-boot failed: 1 of 1 attempts. 'wait for prompt timed out'
538wait for prompt timed out
539end: 1 minimal-boot (duration 00:00:00) [common]
540case: minimal-boot
541case_id: 847
542definition: lava
543duration: 0.00
544extra: ...
545level: 1
546namespace: common
547result: fail
548Cleaning after the job
549start: 3.1 power-off (timeout 00:00:10) [common]
550end: 3.1 power-off (duration 00:00:00) [common]
551case: power-off
552case_id: 848
553definition: lava
554duration: 0.00
555extra: ...
556level: 3.1
557namespace: common
558result: pass
559start: 3.2 read-feedback (timeout 00:15:00) [common]
560Finalising connection for namespace 'common'
561Disconnecting ShellSession
562Disconnecting from telnet: Finalise
563]
564quit
565 quit
566end: 3.2 read-feedback (duration 00:00:00) [common]
567JobError: Your job cannot terminate cleanly.
568case: job
569case_id: 849
570definition: lava
571error_msg: wait for prompt timed out
572error_type: Job
573result: fail
574
575Top of page
576
577Please read the triage guidelines for help on debugging failures in the test job, test definitions or in individual test cases.