· 6 years ago · Oct 02, 2019, 11:42 AM
1U-Boot 2017.09-rockchip-ayufan-1065-g95f6152134 (Aug 26 2019 - 12:41:34 +0000)
2
3Model: Pine64 RockPro64
4DRAM: 2 GiB
5DCDC_REG1@vdd_center: ; enabling
6DCDC_REG2@vdd_cpu_l: ; enabling
7DCDC_REG3@vcc_ddr: ; enabling (ret: -38)
8DCDC_REG4@vcc_1v8: set 1800000 uV; enabling
9LDO_REG1@vcc1v8_dvp: set 1800000 uV; enabling
10LDO_REG2@vcc3v0_touch: set 3000000 uV; enabling
11LDO_REG3@vcc1v8_pmu: set 1800000 uV; enabling
12LDO_REG4@vcc_sd: set 3300000 uV; enabling
13LDO_REG5@vcca3v0_codec: set 3000000 uV; enabling
14LDO_REG6@vcc_1v5: set 1500000 uV; enabling
15LDO_REG7@vcca1v8_codec: set 1800000 uV; enabling
16LDO_REG8@vcc_3v0: set 3000000 uV; enabling
17SWITCH_REG1@vcc3v3_s3: ; enabling (ret: -38)
18SWITCH_REG2@vcc3v3_s0: ; enabling (ret: -38)
19vcc1v8-s0@vcc1v8_s0: set 1800000 uV; enabling (ret: -38)
20dc-12v@dc_12v: set 12000000 uV; enabling (ret: -38)
21vcc-sys@vcc_sys: set 5000000 uV; enabling (ret: -38)
22vcc3v3-sys@vcc3v3_sys: set 3300000 uV; enabling (ret: -38)
23vcc-phy-regulator@vcc_phy: ; enabling (ret: -38)
24vdd-log@vdd_log: ; enabling (ret: -38)
25MMC: sdhci@fe330000: 0, dwmmc@fe320000: 1
26SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
27*** Warning - bad CRC, using default environment
28
29In: serial@ff1a0000
30Out: serial@ff1a0000
31Err: serial@ff1a0000
32Model: Pine64 RockPro64
33normal boot
34Net: eth0: ethernet@fe300000
35Hit any key to stop autoboot: 0
36Card did not respond to voltage select!
37mmc_init: -95, time 20
38switch to partitions #0, OK
39mmc1 is current device
40Scanning mmc 1:7...
41Found /boot/extlinux/extlinux.conf
42Retrieving file: /boot/extlinux/extlinux.conf
432017 bytes read in 20 ms (97.7 KiB/s)
44select kernel
451: kernel-5.4.0-rc1-1120-ayufan-gf8639cacc398
462: kernel-5.4.0-rc1-1120-ayufan-gf8639cacc398-memtest
473: kernel-4.4.190-1233-rockchip-ayufan-gd3f1be0ed310
484: kernel-4.4.190-1233-rockchip-ayufan-gd3f1be0ed310-memtest
49Enter choice: 1: kernel-5.4.0-rc1-1120-ayufan-gf8639cacc398
50Retrieving file: /boot/initrd.img-5.4.0-rc1-1120-ayufan-gf8639cacc398
514550650 bytes read in 506 ms (8.6 MiB/s)
52Retrieving file: /boot/vmlinuz-5.4.0-rc1-1120-ayufan-gf8639cacc398
5331166976 bytes read in 3324 ms (8.9 MiB/s)
54append: rw panic=10 init=/sbin/init coherent_pool=1M ethaddr=62:03:b0:d6:dc:b3 4
55Retrieving file: /boot/dtbs/5.4.0-rc1-1120-ayufan-gf8639cacc398/rockchip/rk3399b
5656621 bytes read in 92 ms (600.6 KiB/s)
57## Flattened Device Tree blob at 01f00000
58 Booting using the fdt blob at 0x1f00000
59 Loading Ramdisk to 7daa9000, end 7deffffa ... OK
60 Loading Device Tree to 000000007da98000, end 000000007daa8d2c ... OK
61
62Starting kernel ...
63
64[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
65[ 0.000000] Linux version 5.4.0-rc1-1120-ayufan-gf8639cacc398 (root@runner-f9
66[ 0.000000] Machine model: Pine64 RockPro64
67[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000ff1a0000 (options '')
68[ 0.000000] printk: bootconsole [uart8250] enabled
69[ 0.000000] efi: Getting EFI parameters from FDT:
70[ 0.000000] efi: UEFI not found.
71[ 0.000000] cma: Reserved 16 MiB at 0x000000007f000000
72[ 0.000000] NUMA: No NUMA configuration found
73[ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x000000007ffffff]
74[ 0.000000] NUMA: NODE_DATA [mem 0x7ebb1800-0x7ebb2fff]
75[ 0.000000] Zone ranges:
76[ 0.000000] DMA32 [mem 0x0000000000200000-0x000000007fffffff]
77[ 0.000000] Normal empty
78[ 0.000000] Movable zone start for each node
79[ 0.000000] Early memory node ranges
80[ 0.000000] node 0: [mem 0x0000000000200000-0x000000007fffffff]
81[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x000000007fffffff]
82[ 0.000000] psci: probing for conduit method from DT.
83[ 0.000000] psci: PSCIv1.0 detected in firmware.
84[ 0.000000] psci: Using standard PSCI v0.2 function IDs
85[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
86[ 0.000000] psci: SMC Calling Convention v1.0
87[ 0.000000] percpu: Embedded 22 pages/cpu s53144 r8192 d28776 u90112
88[ 0.000000] Detected VIPT I-cache on CPU0
89[ 0.000000] CPU features: detected: ARM erratum 845719
90[ 0.000000] CPU features: detected: GIC system register CPU interface
91[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 515592
92[ 0.000000] Policy zone: DMA32
93[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 rw pani4
94[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
95[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes,)
96[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
97[ 0.000000] Memory: 2002436K/2095104K available (18684K kernel code, 2020K r)
98[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
99[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
100[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
101[ 0.000000] Tasks RCU enabled.
102[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 ji.
103[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
104[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
105[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
106[ 0.000000] GICv3: 988 SPIs implemented
107[ 0.000000] GICv3: 0 Extended SPIs implemented
108[ 0.000000] GICv3: Distributor has no Range Selector support
109[ 0.000000] GICv3: 16 PPIs implemented
110[ 0.000000] GICv3: no VLPI support, no direct LPI support
111[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
112[ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
113[ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @7e080000 (flat,)
114[ 0.000000] ITS: using cache flushing for cmd queue
115[ 0.000000] GICv3: using LPI property table @0x000000007e040000
116[ 0.000000] GIC: using cache flushing for LPI property table
117[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x000000007e05000
118[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0}
119[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@1}
120[ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x458 wi0
121[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
122[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless
123[ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398s
124[ 0.003309] Console: colour dummy device 80x25
125[ 0.003739] printk: console [tty0] enabled
126[ 0.004140] printk: bootconsole [uart8250] disabled
127[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
128[ 0.000000] Linux version 5.4.0-rc1-1120-ayufan-gf8639cacc398 (root@runner-f9
129[ 0.000000] Machine model: Pine64 RockPro64
130[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000ff1a0000 (options '')
131[ 0.000000] printk: bootconsole [uart8250] enabled
132[ 0.000000] efi: Getting EFI parameters from FDT:
133[ 0.000000] efi: UEFI not found.
134[ 0.000000] cma: Reserved 16 MiB at 0x000000007f000000
135[ 0.000000] NUMA: No NUMA configuration found
136[ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x000000007ffffff]
137[ 0.000000] NUMA: NODE_DATA [mem 0x7ebb1800-0x7ebb2fff]
138[ 0.000000] Zone ranges:
139[ 0.000000] DMA32 [mem 0x0000000000200000-0x000000007fffffff]
140[ 0.000000] Normal empty
141[ 0.000000] Movable zone start for each node
142[ 0.000000] Early memory node ranges
143[ 0.000000] node 0: [mem 0x0000000000200000-0x000000007fffffff]
144[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x000000007fffffff]
145[ 0.000000] psci: probing for conduit method from DT.
146[ 0.000000] psci: PSCIv1.0 detected in firmware.
147[ 0.000000] psci: Using standard PSCI v0.2 function IDs
148[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
149[ 0.000000] psci: SMC Calling Convention v1.0
150[ 0.000000] percpu: Embedded 22 pages/cpu s53144 r8192 d28776 u90112
151[ 0.000000] Detected VIPT I-cache on CPU0
152[ 0.000000] CPU features: detected: ARM erratum 845719
153[ 0.000000] CPU features: detected: GIC system register CPU interface
154[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 515592
155[ 0.000000] Policy zone: DMA32
156[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 rw pani4
157[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
158[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes,)
159[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
160[ 0.000000] Memory: 2002436K/2095104K available (18684K kernel code, 2020K r)
161[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
162[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
163[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
164[ 0.000000] Tasks RCU enabled.
165[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 ji.
166[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
167[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
168[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
169[ 0.000000] GICv3: 988 SPIs implemented
170[ 0.000000] GICv3: 0 Extended SPIs implemented
171[ 0.000000] GICv3: Distributor has no Range Selector support
172[ 0.000000] GICv3: 16 PPIs implemented
173[ 0.000000] GICv3: no VLPI support, no direct LPI support
174[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
175[ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
176[ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @7e080000 (flat,)
177[ 0.000000] ITS: using cache flushing for cmd queue
178[ 0.000000] GICv3: using LPI property table @0x000000007e040000
179[ 0.000000] GIC: using cache flushing for LPI property table
180[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x000000007e05000
181[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0}
182[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@1}
183[ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x458 wi0
184[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
185[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless
186[ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398s
187[ 0.003309] Console: colour dummy device 80x25
188[ 0.003739] printk: console [tty0] enabled
189[ 0.004140] printk: bootconsole [uart8250] disabled
190[ 0.004720] Calibrating delay loop (skipped), value calculated using timer f)
191[ 0.004756] pid_max: default: 32768 minimum: 301
192[ 0.004901] LSM: Security Framework initializing
193[ 0.005008] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, lin)
194[ 0.005044] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
195[ 0.027363] ASID allocator initialised with 32768 entries
196[ 0.035356] rcu: Hierarchical SRCU implementation.
197[ 0.043501] Platform MSI: interrupt-controller@fee20000 domain created
198[ 0.043930] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@feed
199[ 0.048391] EFI services will not be available.
200[ 0.056411] smp: Bringing up secondary CPUs ...
201[ 0.088634] Detected VIPT I-cache on CPU1
202[ 0.088675] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
203[ 0.088692] GICv3: CPU1: using allocated LPI pending table @0x000000007e06000
204[ 0.088743] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
205[ 0.120704] Detected VIPT I-cache on CPU2
206[ 0.120735] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
207[ 0.120749] GICv3: CPU2: using allocated LPI pending table @0x000000007e07000
208[ 0.120782] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
209[ 0.152802] Detected VIPT I-cache on CPU3
210[ 0.152831] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
211[ 0.152844] GICv3: CPU3: using allocated LPI pending table @0x000000007e10000
212[ 0.152875] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
213[ 0.187607] CPU features: detected: EL2 vector hardening
214[ 0.187948] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware
215[ 0.188327] Detected PIPT I-cache on CPU4
216[ 0.189561] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
217[ 0.190028] GICv3: CPU4: using allocated LPI pending table @0x000000007e11000
218[ 0.191262] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
219[ 0.231299] Detected PIPT I-cache on CPU5
220[ 0.232494] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
221[ 0.232918] GICv3: CPU5: using allocated LPI pending table @0x000000007e12000
222[ 0.234013] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
223[ 0.239105] smp: Brought up 1 node, 6 CPUs
224[ 0.239497] SMP: Total of 6 processors activated.
225[ 0.239530] CPU features: detected: 32-bit EL0 Support
226[ 0.239562] CPU features: detected: CRC32 instructions
227[ 0.464306] CPU: All CPU(s) started at EL2
228[ 0.465162] alternatives: patching kernel code
229[ 0.470388] devtmpfs: initialized
230[ 0.492862] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
231[ 0.493100] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
232[ 0.494779] xor: measuring software checksum speed
233[ 0.532324] 8regs : 1152.000 MB/sec
234[ 0.571911] 32regs : 52.000 MB/sec
235[ 0.612045] arm64_neon: 48.000 MB/sec
236[ 0.612724] xor: using function: 8regs (1152.000 MB/sec)
237[ 0.613674] pinctrl core: initialized pinctrl subsystem
238[ 0.674820] DMI not present or invalid.
239[ 0.695390] NET: Registered protocol family 16
240[ 0.807999] DMA: preallocated 1024 KiB pool for atomic allocations
241[ 0.809875] audit: initializing netlink subsys (disabled)
242[ 0.815431] audit: type=2000 audit(0.808:1): state=initialized audit_enabled1
243[ 0.880872] cpuidle: using governor menu
244[ 0.906472] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
245[ 0.980478] Serial: AMBA PL011 UART driver
246[ 3.611293] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
247[ 3.612391] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
248[ 3.613199] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
249[ 3.613960] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
250[ 3.925178] cryptd: max_cpu_qlen set to 1000
251[ 4.550691] raid6: neonx8 gen() 26 MB/s
252[ 4.617591] raid6: neonx8 xor() 22 MB/s
253[ 4.685675] raid6: neonx4 gen() 23 MB/s
254[ 4.754598] raid6: neonx4 xor() 20 MB/s
255[ 4.826152] raid6: neonx2 gen() 17 MB/s
256[ 4.895692] raid6: neonx2 xor() 19 MB/s
257[ 4.963297] raid6: neonx1 gen() 340 MB/s
258[ 5.033011] raid6: neonx1 xor() 15 MB/s
259[ 5.101006] raid6: int64x8 gen() 12 MB/s
260[ 5.169066] raid6: int64x8 xor() 9 MB/s
261[ 5.241141] raid6: int64x4 gen() 12 MB/s
262[ 5.309776] raid6: int64x4 xor() 10 MB/s
263[ 5.383384] raid6: int64x2 gen() 9 MB/s
264[ 5.449913] raid6: int64x2 xor() 8 MB/s
265[ 5.522853] raid6: int64x1 gen() 6 MB/s
266[ 5.593309] raid6: int64x1 xor() 6 MB/s
267[ 5.593954] raid6: using algorithm neonx1 gen() 340 MB/s
268[ 5.594565] raid6: .... xor() 15 MB/s, rmw enabled
269[ 5.595174] raid6: using neon recovery algorithm
270[ 5.623919] ACPI: Interpreter disabled.
271[ 5.660218] iommu: Default domain type: Translated
272[ 5.683474] rk_iommu ff650800.iommu: IRQ index 1 not found
273[ 5.700960] rk_iommu ff8f3f00.iommu: IRQ index 1 not found
274[ 5.717310] rk_iommu ff903f00.iommu: IRQ index 1 not found
275[ 5.734099] rk_iommu ff914000.iommu: IRQ index 1 not found
276[ 5.749358] rk_iommu ff924000.iommu: IRQ index 1 not found
277[ 5.760303] vgaarb: loaded
278[ 5.775751] SCSI subsystem initialized
279[ 5.794557] usbcore: registered new interface driver usbfs
280[ 5.797129] usbcore: registered new interface driver hub
281[ 5.803752] usbcore: registered new device driver usb
282[ 5.862209] mc: Linux media interface: v0.10
283[ 5.864206] videodev: Linux video capture interface: v2.00
284[ 5.868349] pps_core: LinuxPPS API ver. 1 registered
285[ 5.869084] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giom>
286[ 5.870932] PTP clock support registered
287[ 5.919922] Advanced Linux Sound Architecture Driver Initialized.
288[ 5.941429] Bluetooth: Core ver 2.22
289[ 5.944186] NET: Registered protocol family 31
290[ 5.944891] Bluetooth: HCI device and connection manager initialized
291[ 5.945789] Bluetooth: HCI socket layer initialized
292[ 5.946749] Bluetooth: L2CAP socket layer initialized
293[ 5.949137] Bluetooth: SCO socket layer initialized
294[ 5.950794] NetLabel: Initializing
295[ 5.951389] NetLabel: domain hash size = 128
296[ 5.951932] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
297[ 5.955331] NetLabel: unlabeled traffic allowed by default
298[ 5.989531] clocksource: Switched to clocksource arch_sys_counter
299[ 5.999744] VFS: Disk quotas dquot_6.6.0
300[ 6.003746] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
301[ 6.019932] pnp: PnP ACPI: disabled
302[ 6.349617] thermal_sys: Registered thermal governor 'step_wise'
303[ 6.349821] thermal_sys: Registered thermal governor 'power_allocator'
304[ 6.378397] NET: Registered protocol family 2
305[ 6.411564] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 163)
306[ 6.415594] TCP established hash table entries: 16384 (order: 5, 131072 byte)
307[ 6.427269] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, line)
308[ 6.447147] TCP: Hash tables configured (established 16384 bind 16384)
309[ 6.454135] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
310[ 6.458844] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
311[ 6.470530] NET: Registered protocol family 1
312[ 6.486089] RPC: Registered named UNIX socket transport module.
313[ 6.486937] RPC: Registered udp transport module.
314[ 6.487560] RPC: Registered tcp transport module.
315[ 6.488162] RPC: Registered tcp NFSv4.1 backchannel transport module.
316[ 6.508191] PCI: CLS 0 bytes, default 64
317[ 6.517751] Trying to unpack rootfs image as initramfs...
318[ 22.690707] Freeing initrd memory: 4440K
319[ 22.742504] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counte
320[ 22.759633] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counte
321[ 22.779685] kvm [1]: IPA Size Limit: 40bits
322[ 22.832669] kvm [1]: vgic-v2@fff20000
323[ 22.835122] kvm [1]: GIC system register CPU interface enabled
324[ 22.843587] kvm [1]: vgic interrupt IRQ10
325[ 22.854268] kvm [1]: Hyp mode initialized successfully
326[ 33.851592] workingset: timestamp_bits=44 max_order=19 bucket_order=0
327[ 34.275774] squashfs: version 4.0 (2009/01/31) Phillip Lougher
328[ 34.313701] NFS: Registering the id_resolver key type
329[ 34.315116] Key type id_resolver registered
330[ 34.315767] Key type id_legacy registered
331[ 34.316753] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
332[ 34.318025] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
333[ 34.374490] fuse: init (API version 7.31)
334[ 34.401804] 9p: Installing v9fs 9p2000 file system support
335[ 36.139067] NET: Registered protocol family 38
336[ 36.140297] Key type asymmetric registered
337[ 36.140982] Asymmetric key parser 'x509' registered
338[ 36.143986] Block layer SCSI generic (bsg) driver version 0.4 loaded (major )
339[ 36.151302] io scheduler mq-deadline registered
340[ 36.152106] io scheduler kyber registered
341[ 37.807504] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-0
342[ 37.808878] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Cha2
343[ 37.880748] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-0
344[ 37.882652] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Ch6
345[ 38.384818] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
346[ 38.479133] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 38, base_baud =A
347[ 38.513903] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 39, base_baud =A
348[ 38.835455] printk: console [ttyS2] enabled
349[ 38.916019] SuperH (H)SCI(F) driver initialized
350[ 38.962821] msm_serial: driver initialized
351[ 39.696938] cacheinfo: Unable to detect cache hierarchy for CPU 0
352[ 40.142551] brd: module loaded
353[ 40.603190] loop: module loaded
354[ 41.930887] spi-nor spi0.0: gd25q128 (16384 Kbytes)
355[ 42.399983] rockchip-spi ff1d0000.spi: chipselect 0 already in use
356[ 42.402725] spi_master spi0: spi_device register error /spi@ff1d0000/spi-fla0
357[ 42.404945] spi_master spi0: Failed to create SPI device for /spi@ff1d0000/s0
358[ 42.528918] libphy: Fixed MDIO Bus: probed
359[ 42.574109] tun: Universal TUN/TAP device driver, 1.6
360[ 42.677002] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
361[ 42.679142] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
362[ 42.683076] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k
363[ 42.684838] igb: Copyright (c) 2007-2014 Intel Corporation.
364[ 42.688880] igbvf: Intel(R) Gigabit Virtual Function Network Driver - versiok
365[ 42.691445] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
366[ 42.727820] sky2: driver version 1.30
367[ 42.843387] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
368[ 42.846066] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
369[ 42.852104] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
370[ 42.854943] rk_gmac-dwmac fe300000.ethernet: no regulator found
371[ 42.856721] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
372[ 42.859190] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
373[ 42.860856] rk_gmac-dwmac fe300000.ethernet: RX delay(0x20).
374[ 42.863409] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
375[ 42.868241] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
376[ 42.870649] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
377[ 42.877634] rk_gmac-dwmac fe300000.ethernet: init for RGMII
378[ 42.884817] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
379[ 42.889963] rk_gmac-dwmac fe300000.ethernet: DWMAC1000
380[ 42.891652] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register suppd
381[ 42.894180] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine suppd
382[ 42.896174] rk_gmac-dwmac fe300000.ethernet: COE Type 2
383[ 42.898160] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
384[ 42.899982] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
385[ 42.903305] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
386[ 42.904957] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
387[ 42.907099] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watr
388[ 43.806843] libphy: stmmac: probed
389[ 43.808605] RTL8211F Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8)
390[ 43.814495] RTL8211F Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8)
391[ 43.936245] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet drr
392[ 43.942111] usbcore: registered new interface driver pegasus
393[ 43.945889] usbcore: registered new interface driver rtl8150
394[ 43.949695] usbcore: registered new interface driver r8152
395[ 43.953776] usbcore: registered new interface driver asix
396[ 43.956929] usbcore: registered new interface driver ax88179_178a
397[ 43.960944] usbcore: registered new interface driver cdc_ether
398[ 43.964786] usbcore: registered new interface driver dm9601
399[ 43.968493] usbcore: registered new interface driver CoreChips
400[ 43.972885] usbcore: registered new interface driver smsc75xx
401[ 43.976901] usbcore: registered new interface driver smsc95xx
402[ 43.980616] usbcore: registered new interface driver net1080
403[ 43.984275] usbcore: registered new interface driver plusb
404[ 43.988217] usbcore: registered new interface driver cdc_subset
405[ 43.992125] usbcore: registered new interface driver MOSCHIP usb-ethernet drr
406[ 43.996670] usbcore: registered new interface driver cdc_ncm
407[ 44.004627] VFIO - User Level meta-driver version: 0.3
408[ 44.130823] OF: graph: no port node found in /syscon@ff770000/usb2-phy@e450/t
409[ 44.133846] dwc3 fe800000.dwc3: IRQ otg not found
410[ 44.135415] dwc3 fe800000.dwc3: IRQ dwc_usb3 not found
411[ 44.145056] dwc3 fe800000.dwc3: IRQ host not found
412[ 44.147513] dwc3 fe800000.dwc3: IRQ dwc_usb3 not found
413[ 44.227206] dwc3 fe900000.dwc3: IRQ host not found
414[ 44.229658] dwc3 fe900000.dwc3: IRQ dwc_usb3 not found
415[ 44.332845] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
416[ 44.335310] ehci-pci: EHCI PCI platform driver
417[ 44.339592] ehci-platform: EHCI generic platform driver
418[ 44.354675] ehci-platform fe380000.usb: EHCI Host Controller
419[ 44.358190] ehci-platform fe380000.usb: new USB bus registered, assigned bus1
420[ 44.364756] ehci-platform fe380000.usb: irq 31, io mem 0xfe380000
421[ 44.382784] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
422[ 44.415761] hub 1-0:1.0: USB hub found
423[ 44.419149] hub 1-0:1.0: 1 port detected
424[ 44.450558] ehci-platform fe3c0000.usb: EHCI Host Controller
425[ 44.453026] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus2
426[ 44.460588] ehci-platform fe3c0000.usb: irq 33, io mem 0xfe3c0000
427[ 44.478668] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
428[ 44.508566] hub 2-0:1.0: USB hub found
429[ 44.511868] hub 2-0:1.0: 1 port detected
430[ 44.548342] ehci-orion: EHCI orion driver
431[ 44.562135] ehci-exynos: EHCI EXYNOS driver
432[ 44.573787] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
433[ 44.576055] ohci-pci: OHCI PCI platform driver
434[ 44.580452] ohci-platform: OHCI generic platform driver
435[ 44.591987] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
436[ 44.595119] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus3
437[ 44.602371] ohci-platform fe3a0000.usb: irq 32, io mem 0xfe3a0000
438[ 44.695173] hub 3-0:1.0: USB hub found
439[ 44.698649] hub 3-0:1.0: 1 port detected
440[ 44.724520] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
441[ 44.727626] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus4
442[ 44.735064] ohci-platform fe3e0000.usb: irq 34, io mem 0xfe3e0000
443[ 44.838546] hub 4-0:1.0: USB hub found
444[ 44.841971] hub 4-0:1.0: 1 port detected
445[ 44.870616] ohci-exynos: OHCI EXYNOS driver
446[ 44.914829] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
447[ 44.917760] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus n5
448[ 44.926012] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110
449[ 44.929080] xhci-hcd xhci-hcd.0.auto: irq 228, io mem 0xfe800000
450[ 44.976474] hub 5-0:1.0: USB hub found
451[ 44.980073] hub 5-0:1.0: 1 port detected
452[ 44.998615] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
453[ 45.000685] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus n6
454[ 45.003683] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
455[ 45.008566] usb usb6: We don't know the algorithms for LPM for this host, di.
456[ 45.040376] hub 6-0:1.0: USB hub found
457[ 45.043623] hub 6-0:1.0: 1 port detected
458[ 45.069915] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
459[ 45.072179] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus n7
460[ 45.079835] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110
461[ 45.084463] xhci-hcd xhci-hcd.1.auto: irq 229, io mem 0xfe900000
462[ 45.131489] hub 7-0:1.0: USB hub found
463[ 45.134841] hub 7-0:1.0: 1 port detected
464[ 45.152982] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
465[ 45.155695] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus n8
466[ 45.158606] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
467[ 45.163606] usb usb8: We don't know the algorithms for LPM for this host, di.
468[ 45.195957] hub 8-0:1.0: USB hub found
469[ 45.199230] hub 8-0:1.0: 1 port detected
470[ 45.242336] usbcore: registered new interface driver usb-storage
471[ 45.556189] i2c /dev entries driver
472[ 45.743623] rk808 0-001b: chip id: 0x0
473[ 45.908414] rk808-rtc rk808-rtc: registered as rtc0
474[ 46.145913] rockchip-rga ff680000.rga: HW Version: 0x03.02
475[ 46.159949] rockchip-rga ff680000.rga: Registered rockchip-rga as /dev/video0
476[ 46.478747] Bluetooth: HCI UART driver ver 2.3
477[ 46.566143] sdhci: Secure Digital Host Controller Interface driver
478[ 46.567892] sdhci: Copyright(c) Pierre Ossman
479[ 46.592013] Synopsys Designware Multimedia Card Interface Driver
480[ 46.657676] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mod.
481[ 46.660399] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
482[ 46.662890] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
483[ 46.666990] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 28,32 bio
484[ 46.674347] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
485[ 46.676140] mmc_host mmc0: card is non-removable.
486[ 46.706156] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz,)
487[ 46.752653] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mod.
488[ 46.756019] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
489[ 46.758542] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
490[ 46.762896] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 29,32 bio
491[ 46.768725] dwmmc_rockchip fe320000.dwmmc: Got CD GPIO
492[ 46.788667] mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
493[ 46.796868] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
494[ 46.799222] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz,)
495[ 46.807039] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
496[ 46.817950] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
497[ 46.882497] random: fast init done
498[ 46.908877] sdhci-pltfm: SDHCI platform and OF driver helper
499[ 46.919669] mmc_host mmc1: Bus speed (slot 0) = 148500000Hz (slot req 150000)
500[ 47.020926] mmc2: CQHCI version 5.10
501[ 47.033205] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 5000000)
502[ 47.073110] mmc2: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using A
503[ 47.260620] ledtrig-cpu: registered to indicate activity on CPUs
504[ 47.358162] usbcore: registered new interface driver usbhid
505[ 47.359830] usbhid: USB HID core driver
506[ 47.436229] xt_time: kernel timezone is -0000
507[ 47.437584] IPVS: Registered protocols (TCP, UDP, SCTP, AH, ESP)
508[ 47.438258] IPVS: Connection hash table configured (size=4096, memory=64Kbyt)
509[ 47.439948] IPVS: ipvs loaded.
510[ 47.440242] IPVS: [rr] scheduler registered.
511[ 47.440633] IPVS: [wrr] scheduler registered.
512[ 47.441097] IPVS: [lc] scheduler registered.
513[ 47.441489] IPVS: [wlc] scheduler registered.
514[ 47.441885] IPVS: [fo] scheduler registered.
515[ 47.442274] IPVS: [ovf] scheduler registered.
516[ 47.442683] IPVS: [lblc] scheduler registered.
517[ 47.443099] IPVS: [lblcr] scheduler registered.
518[ 47.443512] IPVS: [dh] scheduler registered.
519[ 47.443903] IPVS: [sh] scheduler registered.
520[ 47.444297] IPVS: [sed] scheduler registered.
521[ 47.444694] IPVS: [nq] scheduler registered.
522[ 47.446158] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
523[ 47.446914] Initializing XFRM netlink socket
524[ 47.448278] NET: Registered protocol family 10
525[ 47.451718] Segment Routing with IPv6
526[ 47.452871] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
527[ 47.454818] NET: Registered protocol family 17
528[ 47.455296] bridge: filtering via arp/ip/ip6tables is no longer available by.
529[ 47.456765] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
530[ 47.457363] Bluetooth: HIDP socket layer initialized
531[ 47.457890] 8021q: 802.1Q VLAN Support v1.8
532[ 47.458469] 9pnet: Installing 9P2000 support
533[ 47.459168] Key type dns_resolver registered
534[ 47.460637] dwmmc_rockchip fe310000.dwmmc: All phases work, using default ph.
535[ 47.462560] registered taskstats version 1
536[ 47.466932] Btrfs loaded, crc32c=crc32c-generic
537[ 47.542870] input: gpio-keys as /devices/platform/gpio-keys/input/input0
538[ 47.558326] rk808-rtc rk808-rtc: setting system clock to 2013-01-18T08:57:16)
539[ 47.559470] of_cfs_init
540[ 47.560370] of_cfs_init: OK
541[ 47.562571] platform regulatory.0: Direct firmware load for regulatory.db fa2
542[ 47.563406] cfg80211: failed to load regulatory.db
543[ 47.563775] ALSA device list:
544[ 47.564371] No soundcards found.
545[ 47.566371] ttyS2 - failed to request DMA
546[ 47.569631] Freeing unused kernel memory: 1408K
547[ 47.593734] Run /init as init process
548[ 47.625932] dwmmc_rockchip fe320000.dwmmc: Successfully tuned phase to 255
549Loading, please wait...
550[ 47.628725] mmc1: new ultra high speed SDR104 SDHC card at address 0001
551[ 47.634035] mmc0: new ultra high speed SDR104 SDIO card at address 0001
552[ 47.654145] tmpfs: Unknown parameter 'size'
553mount: Invalid argument
554[ 47.666955] mmcblk1: mmc1:0001 EB1QT 29.8 GiB
555[ 47.780447] mmcblk1: p1 p2 p3 p4 p5 p6 p7
556Starting version 241
557Begin: Loading essential drivers ... done.
558Begin: Running /scripts/init-premount ... done.
559Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
560Begin: Running /scripts/local-premount ... done.
561Warning: fsck not present, so skipping root file system
562[ 85.716492] EXT4-fs (mmcblk1p7): mounted filesystem with writeback data mode)
563done.
564Begin: Running /scripts/local-bottom ... done.
565Begin: Running /scripts/init-bottom ... done.
566mount: Invalid argument
567[ 88.667683] random: crng init done
568[ 93.540340] systemd[1]: System time before build time, advancing clock.
569[ 93.627361] tmpfs: Unknown parameter 'mode'
570[ 93.630913] systemd[1]: Failed to mount tmpfs at /dev/shm: Invalid argument
571[ 93.654613] tmpfs: Unknown parameter 'mode'
572[ 93.657013] systemd[1]: Failed to mount tmpfs at /run: Invalid argument
573[ 93.682554] tmpfs: Unknown parameter 'mode'
574[ 93.686129] systemd[1]: Failed to mount tmpfs at /run/lock: Invalid argument
575[ 93.722560] tmpfs: Unknown parameter 'mode'
576[ 93.725005] systemd[1]: Failed to mount tmpfs at /sys/fs/cgroup: Invalid argt
577[ 93.776292] systemd[1]: Failed to mount cgroup at /sys/fs/cgroup/systemd: Noy
578[!!!!!!] Failed to mount API filesystems.
579[ 93.862654] systemd[1]: Freezing execution.