· 9 years ago · Oct 04, 2016, 07:46 AM
1#
2# boot
3#
4
5** MARVELL BOARD: DB-88F6702A-BP LE
6
7U-Boot 1.1.4 (Apr 19 2012 - 11:21:19) Marvell version: 3.6.0.DNS-320B.01
8
9U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
10
11Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
12SysClock = 400Mhz , TClock = 166Mhz
13
14DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
15DRAM CS[0] base 0x00000000 size 128MB
16DRAM Total size 128MB 16bit width
17Addresses 8M - 0M are saved for the U-Boot usage.
18Mem malloc Initialization (8M - 7M): Done
19NAND:128 MB
20Flash: 0 kB
21
22CPU : Marvell Feroceon (Rev 1)
23
24Streaming disabled
25Write allocate disabled
26
27
28USB 0: host mode
29PEX 0: interface detected no Link.
30Net: egiga0 [PRIME]
31Hit any key to stop autoboot: 0
32
33NAND read: device 0 offset 0x100000, size 0x300000
34load addr .... =a00000
35
36 3145728 bytes read: OK
37
38NAND read: device 0 offset 0x600000, size 0x300000
39load addr .... =f00000
40
41 3145728 bytes read: OK
42## Booting image at 00a00000 ...
43 Image Name: Linux-2.6.31.8
44 Created: 2012-01-17 10:46:18 UTC
45 Image Type: ARM Linux Kernel Image (uncompressed)
46 Data Size: 2610908 Bytes = 2.5 MB
47 Load Address: 00008000
48 Entry Point: 00008000
49 Verifying Checksum ... OK
50OK
51## Loading Ramdisk Image at 00f00000 ...
52 Image Name: Ramdisk
53 Created: 2012-07-06 11:53:44 UTC
54 Image Type: ARM Linux RAMDisk Image (gzip compressed)
55 Data Size: 1750186 Bytes = 1.7 MB
56 Load Address: 00e00000
57 Entry Point: 00e00000
58 Verifying Checksum ... OK
59
60Starting kernel ...
61
62Uncompressing Linux... done, booting the kernel.
63Linux version 2.6.31.8 (jack@swtest5) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #3 Tue Jan 17 18:46:16 CST 2012
64CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
65CPU: VIVT data cache, VIVT instruction cache
66Machine: Feroceon-KW
67Using UBoot passing parameters structure
68Memory policy: ECC disabled, Data cache writeback
69Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32512
70Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none
71PID hash table entries: 512 (order: 9, 2048 bytes)
72Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
73Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
74Memory: 128MB = 128MB total
75Memory: 115468KB available (4924K code, 334K data, 136K init, 0K highmem)
76Hierarchical RCU implementation.
77NR_IRQS:128
78Console: colour dummy device 80x30
79Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
80Mount-cache hash table entries: 512
81CPU: Testing write buffer coherency: ok
82NET: Registered protocol family 16
83Feroceon L2: Enabling L2
84Feroceon L2: Cache support initialised.
85
86CPU Interface
87-------------
88SDRAM_CS0 ....base 00000000, size 128MB
89SDRAM_CS1 ....disable
90SDRAM_CS2 ....disable
91SDRAM_CS3 ....disable
92PEX0_MEM ....base e0000000, size 128MB
93PEX0_IO ....base f2000000, size 1MB
94PEX1_MEM ....no such
95PEX1_IO ....no such
96INTER_REGS ....base f1000000, size 1MB
97NFLASH_CS ....base fa000000, size 2MB
98SPI_CS ....base f4000000, size 16MB
99BOOT_ROM_CS ....no such
100DEV_BOOTCS ....no such
101CRYPT_ENG ....base f0000000, size 2MB
102
103 Marvell Development Board (LSP Version KW_LSP_5.1.3_patch29)-- DB-88F6702A-BP Soc: 88F6702 A1 LE
104
105 Detected Tclk 166666667 and SysClk 400000000
106MV Buttons Device Load
107Marvell USB EHCI Host controller #0: c403e740
108PEX0 interface detected no Link.
109PCI: bus0: Fast back to back transfers enabled
110mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
111bio: create slab <bio-0> at 0
112SCSI subsystem initialized
113usbcore: registered new interface driver usbfs
114usbcore: registered new interface driver hub
115usbcore: registered new device driver usb
116NET: Registered protocol family 2
117IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
118TCP established hash table entries: 4096 (order: 3, 32768 bytes)
119TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
120TCP: Hash tables configured (established 4096 bind 4096)
121TCP reno registered
122NET: Registered protocol family 1
123Trying to unpack rootfs image as initramfs...
124rootfs image is not initramfs (no cpio magic); looks like an initrd
125Freeing initrd memory: 1708K
126RTC has been updated!!!
127rtc mv_rtc: rtc core: registered kw-rtc as rtc0
128RTC registered
129cpufreq: Init kirkwood cpufreq driver
130XOR registered 4 channels
131XOR 2nd invalidate WA enabled
132cesadev_init(c000ed5c)
133mvCesaInit: sessions=640, queue=64, pSram=f0000000
134MV Buttons Driver Load
135VFS: Disk quotas dquot_6.5.2
136Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
137squashfs: version 4.0 (2009/01/31) Phillip Lougher
138Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
139NTFS driver 2.1.29 [Flags: R/O].
140JFFS2 version 2.2. (NAND) ?? 2001-2006 Red Hat, Inc.
141fuse init (API version 7.12)
142msgmni has been set to 229
143alg: No test for cipher_null (cipher_null-generic)
144alg: No test for ecb(cipher_null) (ecb-cipher_null)
145alg: No test for digest_null (digest_null-generic)
146alg: No test for compress_null (compress_null-generic)
147alg: No test for lzma (lzma-generic)
148alg: No test for stdrng (krng)
149alg: No test for hmac(digest_null) (hmac(digest_null-generic))
150Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
151io scheduler noop registered
152io scheduler anticipatory registered (default)
153Initializing ths8200_init
154Initializing dove_adi9889_init
155Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
156serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
157console [ttyS0] enabled
158serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
159brd: module loaded
160loop: module loaded
161Integrated Sata device found
162IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
163scsi0 : Marvell SCSI to SATA adapter
164scsi1 : Marvell SCSI to SATA adapter
165Loading Marvell Ethernet Driver:
166 o Cached descriptors in DRAM
167 o DRAM SW cache-coherency
168 o 2 Giga ports supported
169 o Single RX Queue support - ETH_DEF_RXQ=0
170 o Single TX Queue support - ETH_DEF_TXQ=0
171 o TCP segmentation offload (TSO) supported
172 o Large Receive offload (LRO) supported
173 o Receive checksum offload supported
174 o Transmit checksum offload supported
175 o Network Fast Processing (Routing) supported - (Disabled)
176 o Driver ERROR statistics enabled
177 o Proc tool API enabled
178 o SKB Reuse supported - (Disabled)
179 o SKB Recycle supported - (Disabled)
180 o Rx descripors: q0=128
181 o Tx descripors: q0=532
182 o Loading network interface(s):
183 o register under mv88fx_eth platform
184 o egiga0, ifindex = 2, GbE port = 0
185
186Warning: Giga 1 is Powered Off
187
188mvFpRuleDb (c4569000): 1024 entries, 4096 bytes
189Counter=0, opIdx=6, overhead=16
190Counter=1, opIdx=2, overhead=0
191Counter=2, opIdx=1, overhead=18
192Counter=3, opIdx=2, overhead=0
193NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
194Scanning device for bad blocks
195Bad eraseblock 739 at 0x000005c60000
196Using static partition definition
197Creating 7 MTD partitions on "nand_mtd":
1980x000000000000-0x000000100000 : "u-boot"
1990x000000100000-0x000000600000 : "uImage"
2000x000000600000-0x000000b00000 : "ramdisk"
2010x000000b00000-0x000006f00000 : "image"
2020x000006f00000-0x000007900000 : "rescue firmware"
2030x000007900000-0x000007e00000 : "config"
2040x000007e00000-0x000008000000 : "my-dlink"
205ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
206ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
207ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
208ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
209ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
210usb usb1: configuration #1 chosen from 1 choice
211hub 1-0:1.0: USB hub found
212hub 1-0:1.0: 1 port detected
213ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
214uhci_hcd: USB Universal Host Controller Interface driver
215Initializing USB Mass Storage driver...
216usbcore: registered new interface driver usb-storage
217USB Mass Storage support registered.
218mice: PS/2 mouse device common for all mice
219i2c /dev entries driver
220md: linear personality registered for level -1
221md: raid0 personality registered for level 0
222md: raid1 personality registered for level 1
223device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
224usbcore: registered new interface driver usbhid
225usbhid: v2.6:USB HID core driver
226TCP cubic registered
227NET: Registered protocol family 17
228RPC: Registered udp transport module.
229RPC: Registered tcp transport module.
230rtc mv_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
231md: Waiting for all devices to be available before autodetect
232md: If you don't use raid, use raid=noautodetect
233md: Autodetecting RAID arrays.
234md: Scanned 0 and added 0 devices.
235md: autorun ...
236md: ... autorun DONE.
237RAMDISK: gzip image found at block 0
238EXT4-fs (ram0): no journal
239EXT4-fs (ram0): delayed allocation enabled
240EXT4-fs: mballoc enabled
241EXT4-fs (ram0): mounted filesystem without journal
242VFS: Mounted root (ext4 filesystem) on device 1:0.
243Freeing init memory: 136K
244init started: BusyBox v1.11.2 (2012-06-28 16:57:05 CST)
245starting pid 538, tty '': '/etc/rc.sh'
246** Mounting /etc/fstab
247umount: proc: not mounted
248umount: proc: not mounted
249umount: /usr/local/modules: not mounted
250sh: can't open /usr/sbin/pre_usb.sh
251insmod: applet not found
252umount: /usr/local/tmp/image.cfs: not found
253umount: /usr/local/tmp: not mounted
254first good block is 0
255image len = 25034752 , image checksum = 8b73f1e3
256dump image checksum=8b73f1e3
257rmmod: applet not found
258ln: /lib/./libnss_dns-2.8.so: File exists
259ln: /lib/./libnss_dns.so.2: File exists
260ln: /usr/sbin/./system_init: File exists
261mknod: /dev/REG: File exists
262hardware init
263GbE port 0: TxEnable WA - Enabled, deep=1, tx_en_bk=1
264
265mtd check v1.01.05292012
266/usr/local/config free size is 4747264
267** copy config files
268cp: cannot stat '/usr/local/config/user.log.old': No such file or directory
269usbcore: registered new interface driver usblp
270** set loopback interface
271old ver:20120712
272new ver:20120712
273first good block is 0
274ECC failed: 0
275ECC corrected: 0
276Number of bad blocks: 0
277Number of bbt blocks: 0
278Block size 131072, page size 2048, OOB sizegiga0: mac address changed
279e 64
280Dumping data starting at 0x00000000 and ending at 0x00000800...
281mac1 = 11:22:33:44:55:66
282lan0:ifconfig egiga0 hw ether 11:22:33:44:55:66
283egiga0: link up, full duplex, speed 100 Mbps
284egiga0: started
285DNS-320B function
286NET: Registered protocol family 10
287lo: Disabled Privacy Extensions
288IPv6 over IPv4 tunneling driver
289sit0: Disabled Privacy Extensions
290ip6tnl0: Disabled Privacy Extensions
291IPv4 over IPv4 tunneling driver
292tunl0: Disabled Privacy Extensions
293net.ipv6.conf.default.accept_dad = 2
294net.ipv6.conf.egiga0.accept_dad = 2
295net.ipv6.conf.default.dad_transmits = 1
296net.ipv6.conf.egiga0.dad_transmits = 1
297net.ipv6.conf.default.forwarding = 0
298net.ipv6.conf.default.accept_redirects = 1
299*** execute rc.init.sh
300awk: /var/run/udhcpc0.pid: No such file or directory
301udhcpc (v1.11.2) started
302Sending discover...
303Sending select for 192.168.6.167...
304Lease of 192.168.6.167 obtained, lease time 21600
305sh: you need to specify whom to kill
306crond[1313]: crond (busybox 1.11.2) started, log level 8
307
308deleting routers
309route: SIOCDELRT: No such process
310call load_module network
311ip: RTNETLINK answers: Operation not supported
312ip: RTNETLINK answers: Operation not supported
313crond[1355]: crond (busybox 1.11.2) started, log level 8
314
315*** get Time from rtc and set it into system ****
316rtc: RTC time = 2014/1/18 Sat 3:4:26
317Sat Jan 18 03:04:26 UTC 2014
318*** set Time Zone ****
319Sat Jan 18 11:04:26 CST 2014
320*** Do not adjust RTC time ***
321
322Module IPC SERVER Version:(1.00.20090706)
323
324ads=0
325created mail daemon thread 0
326ifconfig: egiga1: error fetching interface information: Device not found
327Generating RSA private key, 1024 bit long modulus
328............................++++++
329.............................................++++++
330e is 65537 (0x10001)
331killall: chk_blockip: no process killed
332Command: wget -T5 -t3 -q http://cfaj.freeshell.org/ipaddr.cgi -O /tmp/exip.0
3332014-01-18 11:04:33: (../../src/log.c.166) server started
3342014-01-18 11:04:41: (../../src/server.c.1396) [note] graceful shutdown started
3352014-01-18 11:04:41: (../../src/log.c.166) server started
3362014-01-18 11:04:41: (../../src/server.c.1512) server stopped by UID = 0 PID = 1445
337system daemon v1.03.0529212
338chk_io v1.02.20120118
339cp: cannot stat '/usr/local/config/ups_slave.dat': No such file or directory
340
341mfg_start version 1.00(2012-07-12)
342
343Sat Jan 18 11:04:43 2014
344
345
346Please press Enter to activate this console. 2014-01-18 11:04:44: (../../src/server.c.1
3472014-01-18 11:04:44: (../../src/log.c.166) server started
3482014-01-18 11:04:44: (../../src/server.c.1512) server stopped by UID = 0 PID = 1445
349LED_POWER_ON