· 6 years ago · Oct 23, 2019, 06:44 AM
1U-Boot SPL 2018.03-34721-gb399abdade (Oct 21 2019 - 13:57:07 +0200)
2Normal Boot
3Trying to boot from MMC1
4
5
6U-Boot 2018.03-34721-gb399abdade (Oct 21 2019 - 13:57:07 +0200)
7
8CPU: Freescale i.MX8MMQ rev1.0 1800 MHz (running at 1200 MHz)
9CPU: Commercial temperature grade (0C to 95C) at 27C
10Reset cause: POR
11Model: Variscite DART-MX8MM board
12I2C: ready
13DRAM: 2 GiB
14MMC: FSL_SDHC: 0, FSL_SDHC: 1
15Loading Environment from MMC... *** Warning - bad CRC, using default environment
16
17In: serial
18Out: serial
19Err: serial
20
21 BuildInfo:
22 - ATF d6451cc
23 - U-Boot 2018.03-34721-gb399abdade
24
25
26Part number: VSM-DT8MM-102
27Assembly: AS1904144564
28Production date: 2019 Jun 02
29Serial Number: f8:dc:7a:2c:90:84
30switch to partitions #0, OK
31mmc0 is current device
32flash target is MMC:0
33Net:
34ethernet@30be0000 MAC address in ROM is 00:00:00:00:00:00
35eth0: ethernet@30be0000
36Fastboot: Normal
37Normal Boot
38Hit any key to stop autoboot: 0
39switch to partitions #0, OK
40mmc0 is current device
41** File not found /boot/boot.scr **
425250707 bytes read in 340 ms (14.7 MiB/s)
43Uncompressed size: 11816968 = 0xB45008
44Booting from mmc ...
4543286 bytes read in 124 ms (340.8 KiB/s)
46## Flattened Device Tree blob at 43000000
47 Booting using the fdt blob at 0x43000000
48 Using Device Tree in place at 0000000043000000, end 000000004300d915
49
50Starting kernel ...
51
52Booting Linux on physical CPU 0x0
53Linux version 4.14.78-g09a8b5955516 (root@titan) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #2 SMP PREEMPT Mon Oct 21 13:57:32 CEST 2019
54Boot CPU: AArch64 Processor [410fd034]
55Machine model: Variscite DART-MX8MM board
56earlycon: ec_imx6q0 at MMIO 0x0000000030860000 (options '115200')
57bootconsole [ec_imx6q0] enabled
58cma: Reserved 640 MiB at 0x0000000090000000
59psci: probing for conduit method from DT.
60psci: PSCIv1.1 detected in firmware.
61psci: Using standard PSCI v0.2 function IDs
62psci: MIGRATE_INFO_TYPE not supported.
63psci: SMC Calling Convention v1.1
64percpu: Embedded 20 pages/cpu @ffff80007ff6a000 s41752 r8192 d31976 u81920
65Detected VIPT I-cache on CPU0
66CPU features: enabling workaround for ARM erratum 845719
67Speculative Store Bypass Disable mitigation not required
68Built 1 zonelists, mobility grouping on. Total pages: 515072
69Kernel command line: console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200 root=/dev/mmcblk1p1 rootwait rw cma=640MB
70log_buf_len individual max cpu contribution: 4096 bytes
71log_buf_len total cpu_extra contributions: 12288 bytes
72log_buf_len min size: 16384 bytes
73log_buf_len: 32768 bytes
74early log buf free: 14560(88%)
75PID hash table entries: 4096 (order: 3, 32768 bytes)
76Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
77Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
78Memory: 1389312K/2093056K available (7358K kernel code, 852K rwdata, 2764K rodata, 512K init, 267K bss, 48384K reserved, 655360K cma-reserved)
79Virtual kernel memory layout:
80 modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB)
81 vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB)
82 .text : 0xffff000008080000 - 0xffff0000087b0000 ( 7360 KB)
83 .rodata : 0xffff0000087b0000 - 0xffff000008a70000 ( 2816 KB)
84 .init : 0xffff000008a70000 - 0xffff000008af0000 ( 512 KB)
85 .data : 0xffff000008af0000 - 0xffff000008bc5008 ( 853 KB)
86 .bss : 0xffff000008bc5008 - 0xffff000008c07ee0 ( 268 KB)
87 fixed : 0xffff7dfffe7fb000 - 0xffff7dfffec00000 ( 4116 KB)
88 PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB)
89 vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum)
90 0xffff7e0000000000 - 0xffff7e0002000000 ( 32 MB actual)
91 memory : 0xffff800000000000 - 0xffff800080000000 ( 2048 MB)
92SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
93Preemptible hierarchical RCU implementation.
94 RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
95 Tasks RCU enabled.
96RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
97NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
98GICv3: GIC: Using split EOI/Deactivate mode
99GICv3: no VLPI support, no direct LPI support
100ITS: No ITS available, not enabling LPIs
101GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000
102i.MX8MM clock driver init done
103arch_timer: cp15 timer(s) running at 8.00MHz (phys).
104clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns
105sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns
106system counter timer init
107sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns
108clocksource: imx sysctr: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns
109Console: colour dummy device 80x25
110Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000)
111pid_max: default: 32768 minimum: 301
112Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
113Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
114ASID allocator initialised with 32768 entries
115Hierarchical SRCU implementation.
116Cannot find MU entry in device tree
117CPU identified as i.MX8MM, silicon rev 1.0
118smp: Bringing up secondary CPUs ...
119Detected VIPT I-cache on CPU1
120GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000
121CPU1: Booted secondary processor [410fd034]
122Detected VIPT I-cache on CPU2
123GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000
124CPU2: Booted secondary processor [410fd034]
125Detected VIPT I-cache on CPU3
126GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000
127CPU3: Booted secondary processor [410fd034]
128smp: Brought up 1 node, 4 CPUs
129SMP: Total of 4 processors activated.
130CPU features: detected feature: GIC system register CPU interface
131CPU features: detected feature: 32-bit EL0 Support
132CPU features: detected feature: Kernel page table isolation (KPTI)
133CPU: All CPU(s) started at EL2
134alternatives: patching kernel code
135devtmpfs: initialized
136random: get_random_u32 called from bucket_table_alloc+0xf8/0x280 with crng_init=0
137clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
138futex hash table entries: 1024 (order: 5, 131072 bytes)
139pinctrl core: initialized pinctrl subsystem
140NET: Registered protocol family 16
141cpuidle: using governor menu
142vdso: 2 pages (1 code @ ffff0000087b6000, 1 data @ ffff000008af4000)
143hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
144DMA: preallocated 256 KiB pool for atomic allocations
145imx8mm-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver
146HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
147vgaarb: loaded
148bd71837 0-004b: Device ID=0xA0
149bd71837 0-004b: gpio_intr = 40
150bd71837 0-004b: chip_irq=104
151bd71837-pmic bd71837-pmic: regulator register name 'buck1'
152bd71837-pmic bd71837-pmic: regulator register name 'buck2'
153bd71837-pmic bd71837-pmic: regulator register name 'buck3'
154bd71837-pmic bd71837-pmic: regulator register name 'buck4'
155bd71837-pmic bd71837-pmic: regulator register name 'buck5'
156bd71837-pmic bd71837-pmic: regulator register name 'buck6'
157bd71837-pmic bd71837-pmic: regulator register name 'buck7'
158bd71837-pmic bd71837-pmic: regulator register name 'buck8'
159bd71837-pmic bd71837-pmic: regulator register name 'ldo1'
160bd71837-pmic bd71837-pmic: regulator register name 'ldo2'
161bd71837-pmic bd71837-pmic: regulator register name 'ldo3'
162bd71837-pmic bd71837-pmic: regulator register name 'ldo4'
163bd71837-pmic bd71837-pmic: regulator register name 'ldo5'
164ldo5: Bringing 3300000uV into 1800000-1800000uV
165bd71837-pmic bd71837-pmic: regulator register name 'ldo6'
166bd71837-pmic bd71837-pmic: regulator register name 'ldo7'
167random: fast init done
168i2c i2c-0: IMX I2C adapter registered
169i2c i2c-0: can't use DMA, using PIO instead.
170i2c i2c-1: IMX I2C adapter registered
171i2c i2c-1: can't use DMA, using PIO instead.
172i2c i2c-2: IMX I2C adapter registered
173i2c i2c-2: can't use DMA, using PIO instead.
174i2c i2c-3: IMX I2C adapter registered
175i2c i2c-3: can't use DMA, using PIO instead.
176media: Linux media interface: v0.10
177Linux video capture interface: v2.00
178pps_core: LinuxPPS API ver. 1 registered
179pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
180PTP clock support registered
181MU is ready for cross core communication!
182virtio_rpmsg_bus virtio0: rpmsg host is online
183imx rpmsg driver is registered.
184Advanced Linux Sound Architecture Driver Initialized.
185clocksource: Switched to clocksource arch_sys_counter
186NET: Registered protocol family 2
187TCP established hash table entries: 16384 (order: 5, 131072 bytes)
188TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
189TCP: Hash tables configured (established 16384 bind 16384)
190UDP hash table entries: 1024 (order: 3, 32768 bytes)
191UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
192NET: Registered protocol family 1
193RPC: Registered named UNIX socket transport module.
194RPC: Registered udp transport module.
195RPC: Registered tcp transport module.
196RPC: Registered tcp NFSv4.1 backchannel transport module.
197hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
198workingset: timestamp_bits=46 max_order=19 bucket_order=0
199NFS: Registering the id_resolver key type
200Key type id_resolver registered
201Key type id_legacy registered
202nfs4filelayout_init: NFSv4 File Layout Driver Registering...
203Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
204io scheduler noop registered
205io scheduler cfq registered (default)
206io scheduler mq-deadline registered
207io scheduler kyber registered
208mxs-dma 33000000.dma-apbh: initialized
209Bus freq driver module loaded
210Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
21130860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 28, base_baud = 1500000) is a IMX
212console [ttymxc0] enabled
213console [ttymxc0] enabled
214bootconsole [ec_imx6q0] disabled
215bootconsole [ec_imx6q0] disabled
21630880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 29, base_baud = 1500000) is a IMX
21730890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 30, base_baud = 1500000) is a IMX
21830a60000.serial: ttymxc3 at MMIO 0x30a60000 (irq = 35, base_baud = 5000000) is a IMX
219[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
220[drm] No driver support for vblank timestamp query.
221imx-drm display-subsystem: bound imx-lcdif-crtc.0 (ops lcdif_crtc_ops)
222imx_sec_dsim_drv 32e10000.mipi_dsi: version number is 0x1060200
223imx-drm display-subsystem: bound 32e10000.mipi_dsi (ops imx_sec_dsim_ops)
224imx-drm display-subsystem: sn65dsi83_connector_mode_valid: mode: 800*480@33000 is valid
225sn65dsi83 0-002c: DSI clock [ 396000000 ] Hz
226sn65dsi83 0-002c: GeoMetry [ 800 x 480 ] Hz
227Console: switching to colour frame buffer device 100x30
228imx-drm display-subsystem: fb0: frame buffer device
229[drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 0
230spi_imx 30820000.ecspi: dma setup error -19, use pio
231spi_imx 30820000.ecspi: probed
232libphy: Fixed MDIO Bus: probed
233CAN device driver interface
234mcp25xxfd spi0.1: CRC read error: computed: ec03 received: 0000 - data: be 00 04 00 00 00 00
235mcp25xxfd spi0.1: CRC read of clock register resulted in a bad CRC mismatch - hw not found
236mcp25xxfd spi0.1: Probe failed, err=84
237mcp25xxfd: probe of spi0.1 failed with error -84
238input: 30370000.snvs:snvs-powerkey as /devices/platform/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0
239edt_ft5x06 1-0038: touchscreen probe failed
240i2c /dev entries driver
241IR NEC protocol handler initialized
242IR RC5(x/sz) protocol handler initialized
243IR RC6 protocol handler initialized
244IR JVC protocol handler initialized
245IR Sony protocol handler initialized
246IR SANYO protocol handler initialized
247IR Sharp protocol handler initialized
248IR MCE Keyboard/mouse protocol handler initialized
249IR XMP protocol handler initialized
250mxc_mipi-csi 32e30000.mipi_csi: 32e30000.mipi_csi supply mipi-phy not found, using dummy regulator
251mxc_mipi-csi 32e30000.mipi_csi: mipi csi v4l2 device registered
252CSI: Registered sensor subdevice: mxc_mipi-csi.0
253mxc_mipi-csi 32e30000.mipi_csi: lanes: 2, hs_settle: 13, clk_settle: 2, wclk: 1, freq: 333000000
254imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0)
255sdhci: Secure Digital Host Controller Interface driver
256sdhci: Copyright(c) Pierre Ossman
257sdhci-pltfm: SDHCI platform and OF driver helper
258mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA
259sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO
260mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA
261mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA
262galcore: clk_get vg clock failed, disable vg!
263Galcore version 6.2.4.163672
264hantrodec 0 : module inserted. Major = 244
265hantrodec 1 : module inserted. Major = 244
266hx280enc: module inserted. Major <243>
267mmc2: new HS400 MMC card at address 0001
268ledtrig-cpu: registered to indicate activity on CPUs
269mmcblk2: mmc2:0001 AJTD4R 14.6 GiB
270mmcblk2boot0: mmc2:0001 AJTD4R partition 1 4.00 MiB
271mmcblk2boot1: mmc2:0001 AJTD4R partition 2 4.00 MiB
272mmcblk2rpmb: mmc2:0001 AJTD4R partition 3 4.00 MiB
273 mmcblk2: p1
274mmc1: host does not support reading read-only switch, assuming write-enable
275caam 30900000.caam: ERA source: CCBVID.
276caam 30900000.caam: device ID = 0x0a16040100000000 (Era 9)
277caam 30900000.caam: job rings = 3, qi = 0, dpaa2 = no
278caam_jr 30901000.jr0: Entropy delay = 3200
279caam_jr 30901000.jr0: Entropy delay = 3600
280caam_jr 30901000.jr0: Instantiated RNG4 SH0.
281mmc1: new ultra high speed SDR104 SDHC card at address 59b4
282mmcblk1: mmc1:59b4 USDU1 14.9 GiB
283 mmcblk1: p1
284caam_jr 30901000.jr0: Instantiated RNG4 SH1.
285caam algorithms registered in /proc/crypto
286caam_jr 30901000.jr0: registering rng-caam
287caam 30900000.caam: caam pkc algorithms registered in /proc/crypto
288wm8904 2-001a: revision A
289fsl-asoc-card sound-wm8904: wm8904-hifi <-> 30030000.sai mapping ok
290NET: Registered protocol family 17
291can: controller area network core (rev 20170425 abi 9)
292NET: Registered protocol family 29
2938021q: 802.1Q VLAN Support v1.8
294Key type dns_resolver registered
295cpu cpu0: registered imx8mq-cpufreq
296imx6q-pcie 33800000.pcie: 33800000.pcie supply epdev_on not found, using dummy regulator
297OF: PCI: host bridge /pcie@0x33800000 ranges:
298OF: PCI: No bus range found for /pcie@0x33800000, using [bus 00-ff]
299OF: PCI: IO 0x1ff80000..0x1ff8ffff -> 0x00000000
300OF: PCI: MEM 0x18000000..0x1fefffff -> 0x18000000
301imx6q-pcie 33800000.pcie: Initialize PHY with EXT REfCLK!.
302imx6q-pcie 33800000.pcie: PHY Initialization End!.
303imx6q-pcie 33800000.pcie: pcie phy pll can't be locked.
304imx6q-pcie 33800000.pcie: failed to initialize host
305imx6q-pcie 33800000.pcie: unable to add pcie port.
306hctosys: unable to open rtc device (rtc0)
307eth_phy_pwr: disabling
308WIFI_REG_ON: disabling
309ALSA device list:
310 #0: wm8904-audio
311EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null)
312VFS: Mounted root (ext4 filesystem) on device 179:129.
313devtmpfs: mounted
314Freeing unused kernel memory: 512K
315systemd[1]: System time before build time, advancing clock.
316systemd[1]: Inserted module 'autofs4'
317NET: Registered protocol family 10
318Segment Routing with IPv6
319ip_tables: (C) 2000-2006 Netfilter Core Team
320systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
321systemd[1]: Detected architecture arm64.
322
323Welcome to Debian GNU/Linux 10 (buster)!
324
325systemd[1]: Set hostname to <imx8mm-var-dart>.
326systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
327systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
328systemd[1]: /lib/systemd/system/pulseaudio.service:5: PIDFile= references path below legacy directory /var/run/, updating /var/run/pulse/pid → /run/pulse/pid; please update the unit file accordingly.
329random: systemd: uninitialized urandom read (16 bytes read)
330random: systemd: uninitialized urandom read (16 bytes read)
331systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
332[ OK ] Started Dispatch Password …ts to Console Directory Watch.
333random: systemd: uninitialized urandom read (16 bytes read)
334systemd[1]: Listening on Syslog Socket.
335[ OK ] Listening on Syslog Socket.
336systemd[1]: Listening on Journal Socket.
337[ OK ] Listening on Journal Socket.
338systemd[1]: Starting Load Kernel Modules...
339 Starting Load Kernel Modules...
340 Mounting POSIX Message Queue File System...
341 Starting Set the console keyboard layout...
342 Mounting Huge Pages Filgpio_bb: loading out-of-tree module taints kernel.
343e System...
344gpio-bb: gpio bit-bang driver version 1.3 ready.
345 Mounting RPC Pipe File System...
346[ OK ] Reached target System Time Synchronized.
347[ OK ] Listening on Journal Socket (/dev/log).
348[ OK ] Created slice User and Session Slice.
349[ OK ] Reached target Slices.
350[ OK ] Created slice system-getty.slice.
351[ OK ] Created slice system-serial\x2dgetty.slice.
352[ OK ] Listening on initctl Compatibility Named Pipe.
353 Starting Remount Root and Kernel File Systems...
354 Mounting Kernel Debug File System...
355[ OK ] Listening on udev Control Socket.
356 Starting Create list of re…odes for the current kernel...
357[ OK ] Listening on RPCbind Server Activation Socket.
358[ OK ] Reached target Swap.
359 Starting Journal Service...
360[ OK ] Started Forward Password R…uests to Wall Directory Watch.
361[ OK ] Reached target Local Encrypted Volumes.
362[ OK ] Listening on udev Kernel Socket.
363 Starting udev Coldplug all Devices...
364[ OK ] Started Journal Service.
365[ OK ] Started Load Kernel Modules.
366[ OK ] Mounted POSIX Message Queue File System.
367[ OK ] Started Set the console keyboard layout.
368[ OK ] Mounted Huge Pages File System.
369[ OK ] Mounted RPC Pipe File System.
370[ OK ] Started Remount Root and Kernel File Systems.
371[ OK ] Mounted Kernel Debug File System.
372[ OK ] Started Create list of req… nodes for the current kernel.
373 Starting Load/Save Random Seed...
374 Starting Create System Users...
375 Mounting Kernel Configuration File System...
376 Starting Apply Kernel Variables...
377 Starting Flush Journal to Persistent Storage...
378[ OK ] Started udev Coldplug all Devices.
379[ OK ] Started Load/Save Random Seed.
380[ OK ] Started Create System Users.
381[ OK ] Mounted Kernel Configuration File System.
382[ OK ] Started Apply Kernel Variables.
383 Starting Create Static Device Nodes in /dev...
384 Starting Helper to synchronize boot up for ifupdown...
385systemd-journald[210]: Received request to flush runtime journal from PID 1
386[ OK ] Started Flush Journal to Persistent Storage.
387[ OK ] Started Create Static Device Nodes in /dev.
388[ OK ] Reached target Local File Systems (Pre).
389[ OK ] Reached target Local File Systems.
390 Starting Set console font and keymap...
391 Starting Create Volatile Files and Directories...
392 Starting Preprocess NFS configuration...
393 Starting udev Kernel Device Manager...
394[ OK ] Started Set console font and keymap.
395[ OK ] Started Preprocess NFS configuration.
396[ OK ] Reached target NFS client services.
397[ OK ] Started Create Volatile Files and Directories.
398 Starting Update UTMP about System Boot/Shutdown...
399 Starting RPC bind portmap service...
400[ OK ] Started Update UTMP about System Boot/Shutdown.
401[ OK ] Started RPC bind portmap service.
402[ OK ] Reached target RPC Port Mapper.
403[ OK ] Reached target Remote File Systems (Pre).
404[ OK ] Reached target Remote File Systems.
405[ OK ] Started udev Kernel Device Manager.
406[ OK ] Reached target System Initialization.
407[ OK ] Listening on D-Bus System Message Bus Socket.
408[ OK ] Reached target Sockets.
409[ OK ] Started Daily apt download activities.
410[ OK ] Started Daily rotation of log files.
411[ OK ] Started local-apt-repository.pathimx-sdma 30bd0000.dma-controller: no iram assigned, using external mem
412.
413imx-sdma 302c0000.dma-controller: no iram assigned, using external mem
414[ OK ] Reached targetimx-sdma 302b0000.dma-controller: no iram assigned, using external mem
415 Paths.
416[ OK ] Started Daily Cleanup of Temporary Directories.
417[ OK ] Started Daily apt upgrade and clean activities.
418[ OK ] Reached target Timers.
419[ OK ] Reached target Basic System.
420imx-sdma 30bd0000.dma-controller: loaded firmware 4.4
421imx-sdma 302c0000.dma-controller: loaded firmware 4.4
422imx-sdma 302b0000.dma-controller: loaded firmware 4.4
423 Starting Bluetooth OBEX service...
424 Starting Login Service...
425 Starting Restore /etc/reso… the ppp link was shut down...
426 Starting PulseAudio system server...
427usbmisc_imx 32e40200.usbmisc: 32e40200.usbmisc supply vbus-wakeup not found, using dummy regulator
428usbmisc_imx 32e50200.usbmisc: 32e50200.usbmisc supply vbus-wakeup not found, using dummy regulator
429input: gpio-keys as /devices/platform/gpio-keys/input/input2
430usb_phy_generic usbphynop1: usbphynop1 supply vcc not found, using dummy regulator
431usb_phy_generic usbphynop2: usbphynop2 supply vcc not found, using dummy regulator
432 Starting Modem Manager...
433 Starting LSB: Start busybox udhcpd at boot time...
434ov5640_mipi 1-003c: 1-003c supply DOVDD not found, using dummy regulator
435pps pps0: new PPS source ptp0
436[ OK ] ov5640_mipi 1-003c: 1-003c supply DVDD not found, using dummy regulator
437Started D-Bus System Mesov5640_mipi 1-003c: 1-003c supply AVDD not found, using dummy regulator
438sage Bus.
439libphy: fec_enet_mii_bus: probed
440fec 30be0000.ethernet eth0: registered PHC device 0
441 Starting Network Manager...
442 Starting System Logging Service...
443ov5640_mipi 1-003c: Read reg error: reg=300a
444ov5640_mipi 1-003c: Camera is not found
445usbcore: registered new interface driver usbfs
446usbcore: registered new interface driver hub
447usbcore: registered new device driver usb
448[ OK ] Started Regular background program processing daemon.
449 Starting rng-tools.service...
450 Starting WPA supplicant...
451 Starting Variscite WIFI setup service...
452ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
453[ OK ] Started Restore /etc/resol…re the ppp link was shut down.
454[ OK ] Found device /dev/ttymxc0.
455random: crng init done
456random: 7 urandom warning(s) missed due to ratelimiting
457[ OK ] Started rng-tools.service.
458imx_usb 32e40000.usb: 32e40000.usb supply vbus not found, using dummy regulator
459imx_usb 32e50000.usb: 32e50000.usb supply vbus not found, using dummy regulator
460ci_hdrc ci_hdrc.1: EHCI Host Controller
461ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
462ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
463hub 1-0:1.0: USB hub found
464hub 1-0:1.0: 1 port detected
465EXT4-fs (mmcblk2p1): mounted filesystem with ordered data mode. Opts: errors=remount-ro
466[ OK ] Started System Logging Service.
467[ OK ] Started LSB: Start busybox udhcpd at boot time.
468[ OK ] Started Manage Sound Card State (restore and store).
469 Starting Save/Restore Sound Card State...
470mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA
471mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
472mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
473mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
474mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
475[ OK ] Started Login Service.
476[ OK ] Started Bluetooth OBEX service.
477[ OK ] Started WPA supplicant.
478mmc0: new ultra high speed SDR104 SDIO card at address 0001
479brcmfmac: brcmf_fw_map_chip_to_name: using brcm/brcmfmac4339-sdio.bin for chip 0x004339(17209) rev 0x000002
480[ OK ] Started Save/Restore Sound Card State.
481 Starting Authorization Manager...
482[ OK ] Reached target Sound Card.
483[ OK ] Started Helper to synchronize boot up for ifupdown.
484 Starting Raise network interfaces...
485[ OK ] Started Authorization Manager.
486[ OK ] Started Network Manager.
487 Starting Hostname Service...
488[ OK ] Started Modem Manager.
489brcmfmac mmc0:0001:1: Falling back to user helper
490brcmfmac: brcmf_c_process_clm_blob: no clm_blob available(err=-11), device may have limited channels available
491brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Jun 26 2018 01:58:05 version 6.37.39.94 (r692107 CY)
492Atheros 8031 ethernet 30be0000.ethernet-1:00: attached PHY driver [Atheros 8031 ethernet] (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
493IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
494[ OK ] Started Raise network interfaces.
495[ OK ] Started Hostname Service.
496 Starting Network Manager Script Dispatcher Service...
497[ OK ] Started Network Manager Script Dispatcher Service.
498IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
499IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
500[ OK ] Started PulseAudio system server.
501[ OK ] Started Variscite WIFI setup service.
502[ OK ] Reached target Network.
503 Starting Network Time Service...
504 Starting OpenBSD Secure Shell server...
505 Starting /etc/rc.local Compatibility...
506 Starting Permit User Sessions...
507 Starting Variscite Bluetooth setup service...
508[ OK ] Started Network Time Service.
509[ OK ] Started /etc/rc.local Compatibility.
510[ OK ] Started Permit User Sessions.
511 Starting Weston Wayland Compositor (on tty7)...
512[ OK ] Started Pv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
513;39mSerial Getty on ttymxc0.
514[ OK ] Started Getty on tty1.
515[ OK ] Reached target Login Prompts.
516[ OK ] Started Weston Wayland Compositor (on tty7).
517[ OK ] Started OpenBSD Secure Shell server.
518[ OK ] Created slice User Slice of UID 0.
519 Starting User Runtime Directory /run/user/0...
520IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
521[ OK ] Started User Runtime Directory /run/user/0.
522 Starting User Manager for UID 0...
523[ OK ] Started User Manager for UID 0.
524[ OK ] Started Session c1 of user root.
525imx-drm display-subsystem: sn65dsi83_connector_mode_valid: mode: 800*480@33000 is valid
526[ OK ] Started Variscite Bluetooth setup service.
527[ OK ] Reached target Multi-User System.
528[ OK ] Reached target Graphical Interface.
529 Starting Update UTMP about System Runlevel Changes...
530[ OK ] Started Update UTMP about System Runlevel Changes.
531
532__ __ _ _ _
533\ \ / / (_) (_) |
534 \ \ / /_ _ _ __ _ ___ ___ _| |_ ___
535 \ \/ / _` | '__| / __|/ __| | __/ _ \
536 \ / (_| | | | \__ \ (__| | || __/
537 \/ \__,_|_| |_|___/\___|_|\__\___|
538
539 2019 Variscite, Ltd.
540
541imx8mm-var-dart login: fec 30be0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
542IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
543Bluetooth: Core ver 2.22
544NET: Registered protocol family 31
545Bluetooth: HCI device and connection manager initialized
546Bluetooth: HCI socket layer initialized
547Bluetooth: L2CAP socket layer initialized
548Bluetooth: SCO socket layer initialized
549Bluetooth: HCI UART driver ver 2.3
550Bluetooth: HCI UART protocol H4 registered
551Bluetooth: BNEP (Ethernet Emulation) ver 1.3
552Bluetooth: BNEP filters: protocol multicast
553Bluetooth: BNEP socket layer initialized
554Bluetooth: RFCOMM TTY layer initialized
555Bluetooth: RFCOMM socket layer initialized
556Bluetooth: RFCOMM ver 1.11