· 6 years ago · Mar 02, 2020, 09:52 AM
1
2
3U-Boot 2009.08-dirty (1月 29 2019 - 11:48:08)
4
5CPU: Freescale i.MX53 family 2.1V at 800 MHz
6mx53 pll1: 800MHz
7mx53 pll2: 400MHz
8mx53 pll3: 432MHz
9mx53 pll4: 455MHz
10ipg clock : 66666666Hz
11ipg per clock : 33333333Hz
12uart clock : 66666666Hz
13cspi clock : 108000000Hz
14ahb clock : 133333333Hz
15axi_a clock : 400000000Hz
16axi_b clock : 200000000Hz
17emi_slow clock: 133333333Hz
18ddr clock : 400000000Hz
19esdhc1 clock : 80000000Hz
20esdhc2 clock : 80000000Hz
21esdhc3 clock : 80000000Hz
22esdhc4 clock : 80000000Hz
23nfc clock : 26666666Hz
24Board: MX53-LOCO 1.0 Rev. A
25Boot Reason: [POR]
26Boot Device: SPI NOR
27I2C: ready
28DRAM: 512 MB
29MMC: FSL_ESDHC: 0,FSL_ESDHC: 1
30SF: Detected S25FL128 - 16MB with block size 65536, block count 256, total 16777216 bytes
31In: serial
32Out: serial
33Err: serial
34Serial reinitilized!
35Disable the CPLD watchdog.
36Power up the fan to max speed.
37E2prom read boot flags: 0x05 0x01
38 bootdev = 5..
39setup env for recovery..
40Net: got MAC address from IIM: 00:00:00:00:00:00
41FEC0 [PRIME]
42Press Ctrl+C to stop autoboot: 0
43SF: Detected S25FL128 - 16MB with block size 65536, block count 256, total 16777216 bytes
4416384 KiB S25FL128 - 16MB at 0:1 is now current device
45## Booting kernel from Legacy Image at 70800000 ...
46 Image Name: Linux-2.6.35.3-VeEX+
47 Image Type: ARM Linux Kernel Image (uncompressed)
48 Data Size: 2701568 Bytes = 2.6 MB
49 Load Address: 70008000
50 Entry Point: 70008000
51 Verifying Checksum ... OK
52 Loading Kernel Image ... OK
53OK
54
55Starting kernel ...
56
57Linux version 2.6.35.3-VeEX+ (luo@yanjun-ThinkPad) (gcc version 4.4.4 (4.4.4_09.06.2010) ) #633 PREEMPT Mon Nov 9 14:58:09 CST 2015
58CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
59CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
60Machine: Freescale MX53 LOCO Board
61Memory policy: ECC disabled, Data cache writeback
62Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920
63Kernel command line: console=ttymxc0,115200 root=/dev/mtdblock2 rootwait rw video=mxcdi0fb:RGB666,CLAA-WVGA di0_primary mtdparts=physmap-flash.0:8M(KERNEL),-(CRAMFS)
64PID hash table entries: 2048 (order: 1, 8192 bytes)
65Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
66Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
67Memory: 480MB = 480MB total
68Memory: 481800k/481800k available, 9720k reserved, 0K highmem
69Virtual kernel memory layout:
70 vector : 0xffff0000 - 0xffff1000 ( 4 kB)
71 fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
72 DMA : 0xf8e00000 - 0xffe00000 ( 112 MB)
73 vmalloc : 0x9e800000 - 0xf4000000 (1368 MB)
74 lowmem : 0x80000000 - 0x9e000000 ( 480 MB)
75 pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
76 modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
77 .init : 0x80008000 - 0x80033000 ( 172 kB)
78 .text : 0x80033000 - 0x804d4000 (4740 kB)
79 .data : 0x804ec000 - 0x805279c0 ( 239 kB)
80SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
81Hierarchical RCU implementation.
82 RCU-based detection of stalled CPUs is disabled.
83 Verbose stalled-CPUs detection is disabled.
84NR_IRQS:368
85MXC GPIO hardware
86MXC IRQ initialized
87MXC_Early serial console at MMIO 0x53fbc000 (options '115200')
88bootconsole [ttymxc0] enabled
89Console: colour dummy device 80x30
90Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
91pid_max: default: 32768 minimum: 301
92Mount-cache hash table entries: 512
93CPU: Testing write buffer coherency: ok
94regulator: core version 0.5
95NET: Registered protocol family 16
96i.MX IRAM pool: 128 KB@0x9e840000
97IRAM READY
98CPU is i.MX53 Revision 2.1
99WEIM registers:
100CS0:
1010x00: 0x004100b9
1020x04: 0x00001002
1030x08: 0x3f110101
1040x0C: 0x00000000
1050x10: 0x3f04a2aa
1060x14: 0x00000000
107
108CS1:
1090x00: 0x00c100b9
1100x04: 0x00001002
1110x08: 0x3f777000
1120x0C: 0x00000000
1130x10: 0x3f04a240
1140x14: 0x00000000
115
116CS2:
1170x00: 0x00c100b9
1180x04: 0x00001002
1190x08: 0x3f777000
1200x0C: 0x00000000
1210x10: 0x3f04a240
1220x14: 0x00000000
123USB on!
124Clear the key status: 0x7ff
125Hardware version: 0x1, LCD ID: 0x0
126Using SDMA I.API
127MXC DMA API initialized
128IMX usb wakeup probe
129IMX usb wakeup probe
130bio: create slab <bio-0> at 0
131SCSI subsystem initialized
132CSPI: mxc_spi-0 probed
133usbcore: registered new interface driver usbfs
134usbcore: registered new interface driver hub
135usbcore: registered new device driver usb
136LinuxPPS API ver. 1 registered
137Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
138IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
139Advanced Linux Sound Architecture Driver Version 1.0.23.
140mc34708 Rev 1.2 FinVer 0 detected
141pmic_irq: 279
142PMIC IRQ success!
143PMIC MC34708 ID:0xa
144regulator: SW1: 650 <--> 1437 mV at 1250 mV
145regulator: SW1B: 650 <--> 1437 mV at 1100 mV
146regulator: SW2: 650 <--> 1437 mV at 1300 mV
147regulator: SW3: 650 <--> 1425 mV at 1200 mV
148regulator: SW4A: 1200 <--> 3300 mV at 1500 mV
149regulator: SW4B: 1200 <--> 3300 mV at 1500 mV
150regulator: SW5: 1200 <--> 1975 mV at 1800 mV
151regulator: SWBST:
152regulator: VPLL: 1200 <--> 1800 mV at 1800 mV
153regulator: VREFDDR:
154regulator: VDAC: 2500 <--> 2775 mV at 2775 mV
155regulator: VUSB:
156regulator: VUSB2: 2500 <--> 3000 mV at 2500 mV
157regulator: VGEN1: 1200 <--> 1550 mV at 1300 mV
158regulator: VGEN2: 2500 <--> 3300 mV at 2500 mV
159pmic 0-0008: Loaded
160Switching to clocksource mxc_timer1
161NET: Registered protocol family 2
162IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
163TCP established hash table entries: 16384 (order: 5, 131072 bytes)
164TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
165TCP: Hash tables configured (established 16384 bind 16384)
166TCP reno registered
167UDP hash table entries: 256 (order: 0, 4096 bytes)
168UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
169NET: Registered protocol family 1
170RPC: Registered udp transport module.
171RPC: Registered tcp transport module.
172RPC: Registered tcp NFSv4.1 backchannel transport module.
173LPMode driver module loaded
174Static Power Management for Freescale i.MX5
175PM driver module loaded
176sdram autogating driver module loaded
177Bus freq driver module loaded
178DI0 is primary
179mxc_dvfs_core_probe
180DVFS driver module loaded
181i.MXC CPU frequency driver
182DVFS PER driver module loaded
183NetWinder Floating Point Emulator V0.97 (double precision)
184JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
185msgmni has been set to 941
186alg: No test for stdrng (krng)
187cryptodev: driver loaded.
188io scheduler noop registered
189io scheduler deadline registered
190io scheduler cfq registered (default)
191By setting, LDB driver will not be enabled
192mxc_ipu mxc_ipu: Channel already disabled 9
193mxc_ipu mxc_ipu: Channel already uninitialized 9
194Read eeprom logo_option: 0x0
195EEPROM logo_option: 0x0
196logooption:0x0
197Console: switching to colour frame buffer device 100x30
198Read eeprom logo_option: 0x0
199EEPROM logo_option: 0x0
200logooption:0x0
201mxc_ipu mxc_ipu: Channel already disabled 7
202mxc_ipu mxc_ipu: Channel already uninitialized 7
203Read eeprom logo_option: 0x0
204EEPROM logo_option: 0x0
205logooption:0x0
206mxc_ipu mxc_ipu: Channel already disabled 10
207mxc_ipu mxc_ipu: Channel already uninitialized 10
208Read eeprom logo_option: 0x0
209EEPROM logo_option: 0x0
210logooption:0x0
211Serial: MXC Internal UART driver
212mxcintuart.0: ttymxc0 at MMIO 0x53fbc000 (irq = 31) is a Freescale i.MX
213console [ttymxc0] enabled, bootconsole disabled
214console [ttymxc0] enabled, bootconsole disabled
215mxcintuart.1: ttymxc1 at MMIO 0x53fc0000 (irq = 32) is a Freescale i.MX
216mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 33) is a Freescale i.MX
217mxcintuart.3: ttymxc3 at MMIO 0x53ff0000 (irq = 13) is a Freescale i.MX
218mxcintuart.4: ttymxc4 at MMIO 0x63f90000 (irq = 86) is a Freescale i.MX
219brd: module loaded
220loop: module loaded
221data->name = s25fl128s
222s25fl128s (16384 Kbytes)
223mtd .name = s25fl128s, .size = 0x1000000 (16MiB) .erasesize = 0x00010000 (64KiB) .numeraseregions = 1
224mtd.eraseregions[0] = { .offset = 0x0, .erasesize = 0x00010000 (64KiB), .numblocks = 256 }
225partitions[0] = {.name = bootloader, .offset = 0x0, .size = 0x80000 (512KiB) }
226partitions[1] = {.name = kernel, .offset = 0x80000, .size = 0x400000 (4096KiB) }
227partitions[2] = {.name = rootfs, .offset = 0x480000, .size = 0x780000 (7680KiB) }
228partitions[3] = {.name = usr, .offset = 0xc00000, .size = 0x300000 (3072KiB) }
229partitions[4] = {.name = config, .offset = 0xf00000, .size = 0x100000 (1024KiB) }
230Creating 5 MTD partitions on "s25fl128s":
2310x000000000000-0x000000080000 : "bootloader"
2320x000000080000-0x000000480000 : "kernel"
2330x000000480000-0x000000c00000 : "rootfs"
2340x000000c00000-0x000000f00000 : "usr"
2350x000000f00000-0x000001000000 : "config"
236physmap platform flash device: 04000000 at f0000000
237physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
238Amd/Fujitsu Extended Query Table at 0x0040
239Enabling Spansion 65nm mode, writesize = 512 bytes
240number of CFI chips: 1
2412 cmdlinepart partitions found on MTD device physmap-flash.0
242Creating 2 MTD partitions on "physmap-flash.0":
2430x000000000000-0x000000800000 : "KERNEL"
2440x000000800000-0x000004000000 : "CRAMFS"
245FEC Ethernet Driver
246fec_enet_mii_bus: probed
247ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
248fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
249fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
250fsl-ehci fsl-ehci.0: irq 18, io base 0x53f80000
251fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
252usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
253usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
254usb usb1: Product: Freescale On-Chip EHCI Host Controller
255usb usb1: Manufacturer: Linux 2.6.35.3-VeEX+ ehci_hcd
256usb usb1: SerialNumber: fsl-ehci.0
257hub 1-0:1.0: USB hub found
258hub 1-0:1.0: 1 port detected
259fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
260fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
261fsl-ehci fsl-ehci.1: irq 14, io base 0x53f80200
262fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
263usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
264usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
265usb usb2: Product: Freescale On-Chip EHCI Host Controller
266usb usb2: Manufacturer: Linux 2.6.35.3-VeEX+ ehci_hcd
267usb usb2: SerialNumber: fsl-ehci.1
268hub 2-0:1.0: USB hub found
269hub 2-0:1.0: 1 port detected
270usbcore: registered new interface driver cdc_acm
271cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
272usbcore: registered new interface driver cdc_wdm
273Initializing USB Mass Storage driver...
274usbcore: registered new interface driver usb-storage
275USB Mass Storage support registered.
276mice: PS/2 mouse device common for all mice
277CPLD keypad loaded
278input: cpldkpd as /devices/virtual/input/input0
279reg: 0x00004b33
280LCD BACKLIGHT ON!
281i2c /dev entries driver
282VPU initialized
283mxc_asrc registered
284gpu mmu enabled
285mxsdhci: MXC Secure Digital Host Controller Interface driver
286mxsdhci: MXC SDHCI Controller Driver.
287mmc0: SDHCI detect irq 169 irq 1 INTERNAL DMA
288sgtl5000_hw_read: read reg error : Reg 0x00
289Device with ID register 0 is not a SGTL5000
290No device for DAI imx-ssi-1-0
291No device for DAI imx-ssi-1-1
292No device for DAI imx-ssi-2-0
293No device for DAI imx-ssi-2-1
294ALSA device list:
295 No soundcards found.
296Netfilter messages via NETLINK v0.30.
297nf_conntrack version 0.5.0 (7528 buckets, 30112 max)
298usb 2-1: new high speed USB device using fsl-ehci and address 2
299CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
300nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
301sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
302ctnetlink v0.93: registering with nfnetlink.
303TCP cubic registered
304NET: Registered protocol family 17
305lib80211: common routines for IEEE802.11 drivers
306drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
307VFS: Mounted root (cramfs filesystem) readonly on device 31:2.
308Freeing init memory: 172K
309usb 2-1: New USB device found, idVendor=04b4, idProduct=6572
310usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
311usb 2-1: Product: USB2.0 Hub
312mmc0: new high speed SD card at address 59b4
313mmcblk0: mmc0:59b4 AF SD 1.77 GiB
314 mmcblk0:
315hub 2-1:1.0: USB hub found
316hub 2-1:1.0: 4 ports detected
317 p1 p2 p3
318usb 2-1.2: new high speed USB device using fsl-ehci and address 3
319usb 2-1.2: config 1 interface 0 altsetting 0 endpoint 0x83 has an invalid bInterval 255, changing to 11
320usb 2-1.2: New USB device found, idVendor=0a46, idProduct=9621
321usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
322usb 2-1.4: new high speed USB device using fsl-ehci and address 4
323usb 2-1.4: config 1 interface 0 altsetting 0 endpoint 0x83 has an invalid bInterval 255, changing to 11
324usb 2-1.4: New USB device found, idVendor=0a46, idProduct=9621
325usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
326Mounting /proc and /sys
327Starting the hotplug events dispatcher udevd
328cramfs: bad compressed blocksize 4287703991
329cramfs: bad compressed blocksize 4287703991
330cramfs: bad compressed blocksize 4287703991
331/etc/rc.d/init.d/udev: line 41: udevd: cramfs: bad compressed blocksize 4287704087
332Input/output error
333Synthesizingcramfs: bad compressed blocksize 4287704087
334 initial hotplug events
335cramfs: bad compressed blocksize 4287704087
336/etc/rc.d/init.d/udev: cramfs: bad compressed blocksize 4287704087
337line 41: udevtrigger: Input/outpcramfs: bad compressed blocksize 4287704087
338ut error
339/etc/rc.d/init.d/udev: line 41: udevsettle: Input/output error
340Setting the hostname to freescale
341Running depmod
342depmod: can't change directory to 'lib/modules/2.6.35.3-VeEX+': No such file or directory
343Mounting filesystems
344rm: can't remove '/etc/mtab': Read-only file system
345ln: /etc/mtab: File exists
346mount: mounting /dev/mtdblock3 on /usr/ failed: No such file or directory
347cramfs: bad compressed blocksize 4287636987
348cramfs: bad compressed blocksize 4287636987
349mkdir: can't create directory '/var/dev': Input/output error
350cramfs: bad compressed blocksize 4287636987
351touch: /var/dev/p-event0: Input/output error
352chown: /home/user/.rhosts: Read-only file system
353chown: /home/user: Read-only file system
354chown: /home/user: Read-only file system
355mount: mounting /dev/mmcblk0p1 on /tmp/p1/ failed: No such file or directory
356umount: can't umount /tmp/p1/: Invalid argument
357Done!
358Unable to open i2c control file: No such file or directory
359Unable to open i2c control file: No such file or directory
360Unable to open i2c control file: No such file or directory
361CPLD upgraded, unit will power down...
362cramfs: bad compressed blocksize 4287636987
363Unable to open i2c control file:cramfs: bad compressed blocksize 4287636987
364 No such file or directory
365The system is going down NOW!
366Sent SIGTERM to all processes
367Sent SIGKILL to all processes
368Requesting system halt
369mxc_dvfs_core mxc_dvfs_core.0: disable dvfs during shutdown
370System halted.
371VeEX power off!