· 5 years ago · Feb 19, 2021, 11:02 AM
1feta40i/root:~ # dmesg 10:54:26 21-02-19
2[ 0.000000] Booting Linux on physical CPU 0x0
3[ 0.000000] Linux version 5.10.16-sunxi (root@NervousEnergy) (arm-linux-gnueabihf-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #trunk SMP Tue Feb 16 18:32:59 MSK 2021
4[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d
5[ 0.000000] CPU: div instructions available: patching division code
6[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
7[ 0.000000] OF: fdt: Machine model: Forlinx OKA40i-C
8[ 0.000000] earlycon: uart0 at MMIO32 0x01c28000 (options '115200n8')
9[ 0.000000] printk: bootconsole [uart0] enabled
10[ 0.000000] Memory policy: Data cache writealloc
11[ 0.000000] cma: Reserved 128 MiB at 0x77c00000
12[ 0.000000] Zone ranges:
13[ 0.000000] Normal [mem 0x0000000040000000-0x000000006fffffff]
14[ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff]
15[ 0.000000] Movable zone start for each node
16[ 0.000000] Early memory node ranges
17[ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff]
18[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
19[ 0.000000] On node 0 totalpages: 262144
20[ 0.000000] Normal zone: 1728 pages used for memmap
21[ 0.000000] Normal zone: 0 pages reserved
22[ 0.000000] Normal zone: 196608 pages, LIFO batch:63
23[ 0.000000] HighMem zone: 65536 pages, LIFO batch:15
24[ 0.000000] psci: probing for conduit method from DT.
25[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
26[ 0.000000] percpu: Embedded 21 pages/cpu s53324 r8192 d24500 u86016
27[ 0.000000] pcpu-alloc: s53324 r8192 d24500 u86016 alloc=21*4096
28[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
29[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416
30[ 0.000000] Kernel command line: root=UUID=e160f13e-036d-4f47-96dc-84739247d832 rootwait rootfstype=ext4 earlycon console=ttyS0,115200n hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 consoleblank=0 loglevel=7 ubootpart=e5ad4b56-01 ubootsource=mmc usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16 cgroup_enable=memory swapaccount=1 console=ttyS0,115200n8
31[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
32[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
33[ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
34[ 0.000000] Memory: 880560K/1048576K available (9216K kernel code, 1489K rwdata, 3252K rodata, 1024K init, 356K bss, 36944K reserved, 131072K cma-reserved, 131060K highmem)
35[ 0.000000] random: get_random_u32 called from __kmem_cache_create+0x1d/0x29c with crng_init=0
36[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
37[ 0.000000] ftrace: allocating 42261 entries in 83 pages
38[ 0.000000] ftrace: allocated 83 pages with 4 groups
39[ 0.000000] rcu: Hierarchical RCU implementation.
40[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
41[ 0.000000] Rude variant of Tasks RCU enabled.
42[ 0.000000] Tracing variant of Tasks RCU enabled.
43[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
44[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
45[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
46[ 0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set
47[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
48[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
49[ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
50[ 0.008002] Switching to timer-based delay loop, resolution 41ns
51[ 0.014208] Console: colour dummy device 80x30
52[ 0.018710] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
53[ 0.028986] pid_max: default: 32768 minimum: 301
54[ 0.033802] LSM: Security Framework initializing
55[ 0.038479] Yama: becoming mindful.
56[ 0.042135] AppArmor: AppArmor initialized
57[ 0.046316] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
58[ 0.053632] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
59[ 0.062402] CPU: Testing write buffer coherency: ok
60[ 0.067676] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
61[ 0.074052] Setting up static identity map for 0x40100000 - 0x40100054
62[ 0.080712] rcu: Hierarchical SRCU implementation.
63[ 0.086695] smp: Bringing up secondary CPUs ...
64[ 0.102097] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
65[ 0.112979] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
66[ 0.123786] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
67[ 0.123899] smp: Brought up 1 node, 4 CPUs
68[ 0.144996] SMP: Total of 4 processors activated (192.00 BogoMIPS).
69[ 0.151260] CPU: All CPU(s) started in HYP mode.
70[ 0.155877] CPU: Virtualization extensions available.
71[ 0.161674] allocated 1048576 bytes of page_ext
72[ 0.166804] devtmpfs: initialized
73[ 0.175418] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
74[ 0.183296] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
75[ 0.193072] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
76[ 0.203159] pinctrl core: initialized pinctrl subsystem
77[ 0.209484] NET: Registered protocol family 16
78[ 0.215535] DMA: preallocated 256 KiB pool for atomic coherent allocations
79[ 0.223007] audit: initializing netlink subsys (disabled)
80[ 0.228702] audit: type=2000 audit(0.136:1): state=initialized audit_enabled=0 res=1
81[ 0.229214] thermal_sys: Registered thermal governor 'fair_share'
82[ 0.236458] thermal_sys: Registered thermal governor 'bang_bang'
83[ 0.242551] thermal_sys: Registered thermal governor 'step_wise'
84[ 0.248850] cpuidle: using governor ladder
85[ 0.259082] cpuidle: using governor menu
86[ 0.263562] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
87[ 0.271565] hw-breakpoint: maximum watchpoint size is 8 bytes.
88[ 0.299190] cryptd: max_cpu_qlen set to 1000
89[ 0.374322] raid6: neonx8 gen() 780 MB/s
90[ 0.446388] raid6: neonx8 xor() 578 MB/s
91[ 0.518483] raid6: neonx4 gen() 830 MB/s
92[ 0.590573] raid6: neonx4 xor() 631 MB/s
93[ 0.662660] raid6: neonx2 gen() 915 MB/s
94[ 0.734747] raid6: neonx2 xor() 652 MB/s
95[ 0.806858] raid6: neonx1 gen() 815 MB/s
96[ 0.878929] raid6: neonx1 xor() 565 MB/s
97[ 0.951086] raid6: int32x8 gen() 303 MB/s
98[ 1.023163] raid6: int32x8 xor() 180 MB/s
99[ 1.095281] raid6: int32x4 gen() 354 MB/s
100[ 1.167343] raid6: int32x4 xor() 205 MB/s
101[ 1.239431] raid6: int32x2 gen() 399 MB/s
102[ 1.311558] raid6: int32x2 xor() 213 MB/s
103[ 1.383654] raid6: int32x1 gen() 401 MB/s
104[ 1.455722] raid6: int32x1 xor() 192 MB/s
105[ 1.459992] raid6: using algorithm neonx2 gen() 915 MB/s
106[ 1.465301] raid6: .... xor() 652 MB/s, rmw enabled
107[ 1.470176] raid6: using neon recovery algorithm
108[ 1.475520] iommu: Default domain type: Translated
109[ 1.480766] SCSI subsystem initialized
110[ 1.484732] libata version 3.00 loaded.
111[ 1.484950] usbcore: registered new interface driver usbfs
112[ 1.490496] usbcore: registered new interface driver hub
113[ 1.495882] usbcore: registered new device driver usb
114[ 1.501029] mc: Linux media interface: v0.10
115[ 1.505329] videodev: Linux video capture interface: v2.00
116[ 1.510939] pps_core: LinuxPPS API ver. 1 registered
117[ 1.515907] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
118[ 1.525045] PTP clock support registered
119[ 1.529366] Advanced Linux Sound Architecture Driver Initialized.
120[ 1.536235] NetLabel: Initializing
121[ 1.539663] NetLabel: domain hash size = 128
122[ 1.544020] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
123[ 1.549772] NetLabel: unlabeled traffic allowed by default
124[ 1.556034] clocksource: Switched to clocksource arch_sys_counter
125[ 1.674780] VFS: Disk quotas dquot_6.6.0
126[ 1.678823] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
127[ 1.686356] AppArmor: AppArmor Filesystem Enabled
128[ 1.698727] NET: Registered protocol family 2
129[ 1.703913] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
130[ 1.712359] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
131[ 1.720203] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
132[ 1.727456] TCP: Hash tables configured (established 8192 bind 8192)
133[ 1.733952] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
134[ 1.740623] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
135[ 1.747901] NET: Registered protocol family 1
136[ 1.752640] Trying to unpack rootfs image as initramfs...
137[ 2.428246] Freeing initrd memory: 10300K
138[ 2.434025] Initialise system trusted keyrings
139[ 2.438542] Key type blacklist registered
140[ 2.442804] workingset: timestamp_bits=14 max_order=18 bucket_order=4
141[ 2.454474] zbud: loaded
142[ 2.458442] squashfs: version 4.0 (2009/01/31) Phillip Lougher
143[ 2.465221] fuse: init (API version 7.32)
144[ 2.471713] integrity: Platform Keyring initialized
145[ 2.582205] xor: measuring software checksum speed
146[ 2.594580] arm4regs : 1303 MB/sec
147[ 2.609849] 8regs : 901 MB/sec
148[ 2.625745] 32regs : 851 MB/sec
149[ 2.637544] neon : 1323 MB/sec
150[ 2.641899] xor: using function: neon (1323 MB/sec)
151[ 2.646786] Key type asymmetric registered
152[ 2.650883] Asymmetric key parser 'x509' registered
153[ 2.655923] bounce: pool size: 64 pages
154[ 2.659844] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
155[ 2.667413] io scheduler mq-deadline registered
156[ 2.671964] io scheduler kyber registered
157[ 2.676237] io scheduler bfq registered
158[ 2.683145] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pi not found, using dummy regulator
159[ 2.698086] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
160[ 2.710838] sun8i-mixer 1100000.mixer: Couldn't get our reset line
161[ 2.717167] sun4i-drm display-engine: Couldn't bind all pipelines components
162[ 2.727169] brd: module loaded
163[ 2.736675] loop: module loaded
164[ 2.741598] libphy: Fixed MDIO Bus: probed
165[ 2.746778] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
166[ 2.753351] ehci-platform: EHCI generic platform driver
167[ 2.758958] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
168[ 2.765173] ohci-platform: OHCI generic platform driver
169[ 2.771007] usbcore: registered new interface driver usb-storage
170[ 2.777964] sun6i-rtc 1c20400.rtc: registered as rtc0
171[ 2.783066] sun6i-rtc 1c20400.rtc: setting system clock to 1970-01-01T00:00:11 UTC (11)
172[ 2.791084] sun6i-rtc 1c20400.rtc: RTC enabled
173[ 2.795768] i2c /dev entries driver
174[ 2.800798] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
175[ 2.809814] ledtrig-cpu: registered to indicate activity on CPUs
176[ 2.816299] hid: raw HID events driver (C) Jiri Kosina
177[ 2.821577] usbcore: registered new interface driver usbhid
178[ 2.827156] usbhid: USB HID core driver
179[ 2.833018] Initializing XFRM netlink socket
180[ 2.837850] NET: Registered protocol family 10
181[ 2.878180] Segment Routing with IPv6
182[ 2.882002] NET: Registered protocol family 17
183[ 2.886496] NET: Registered protocol family 15
184[ 2.891026] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
185[ 2.904105] 8021q: 802.1Q VLAN Support v1.8
186[ 2.908356] Key type dns_resolver registered
187[ 2.913110] Registering SWP/SWPB emulation handler
188[ 2.918258] registered taskstats version 1
189[ 2.922390] Loading compiled-in X.509 certificates
190[ 2.933842] Loaded X.509 cert 'Build time autogenerated kernel key: 6d9f5eb36a1104c26251119ff955939bb576470c'
191[ 2.948450] zswap: loaded using pool zstd/z3fold
192[ 2.953920] Key type ._fscrypt registered
193[ 2.957968] Key type .fscrypt registered
194[ 2.961903] Key type fscrypt-provisioning registered
195[ 2.971653] Btrfs loaded, crc32c=crc32c-generic
196[ 2.993315] Key type encrypted registered
197[ 2.997373] AppArmor: AppArmor sha1 policy hashing enabled
198[ 3.018009] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pi not found, using dummy regulator
199[ 3.027861] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
200[ 3.036701] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dummy regulator
201[ 3.045407] printk: console [ttyS0] disabled
202[ 3.049787] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 39, base_baud = 1500000) is a 16550A
203[ 3.058540] printk: console [ttyS0] enabled
204[ 3.066905] printk: bootconsole [uart0] disabled
205[ 3.076929] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator
206[ 3.083740] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 198
207[ 3.090369] sun4i-pinctrl 1c20800.pinctrl: pin-198 (1c28c00.serial) status -517
208[ 3.097685] sun4i-pinctrl 1c20800.pinctrl: could not request pin 198 (PG6) from group PG6 on device 1c20800.pinctrl
209[ 3.108208] dw-apb-uart 1c28c00.serial: Error applying setting, reverse things back
210[ 3.128256] sun4i-drm display-engine: bound 1100000.mixer (ops 0xc0aa092c)
211[ 3.137278] sun4i-drm display-engine: bound 1200000.mixer (ops 0xc0aa092c)
212[ 3.144584] sun4i-drm display-engine: bound 1c70000.tcon-top (ops 0xc0aa4d1c)
213[ 3.152058] sun4i-drm display-engine: bound 1c73000.lcd-controller (ops 0xc0a9c868)
214[ 3.159785] sun8i-dw-hdmi 1ee0000.hdmi: supply hvcc not found, using dummy regulator
215[ 3.184140] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a with HDCP (sun8i_dw_hdmi_phy)
216[ 3.194176] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus driver
217[ 3.202028] sun4i-drm display-engine: bound 1ee0000.hdmi (ops 0xc0a9fe84)
218[ 3.209355] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
219[ 3.217180] sun4i-drm display-engine: [drm] Cannot find any crtc or sizes
220[ 3.225097] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator
221[ 3.231911] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0
222[ 3.238379] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -517
223[ 3.245698] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl
224[ 3.256049] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse things back
225[ 3.264503] ehci-platform 1c19000.usb: EHCI Host Controller
226[ 3.270122] ehci-platform 1c19000.usb: new USB bus registered, assigned bus number 1
227[ 3.278021] sun4i-drm display-engine: [drm] Cannot find any crtc or sizes
228[ 3.285076] ehci-platform 1c19000.usb: irq 33, io mem 0x01c19000
229[ 3.304033] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00
230[ 3.310400] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
231[ 3.318674] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
232[ 3.325901] usb usb1: Product: EHCI Host Controller
233[ 3.330783] usb usb1: Manufacturer: Linux 5.10.16-sunxi ehci_hcd
234[ 3.336794] usb usb1: SerialNumber: 1c19000.usb
235[ 3.341886] hub 1-0:1.0: USB hub found
236[ 3.345696] hub 1-0:1.0: 1 port detected
237[ 3.350662] ehci-platform 1c1c000.usb: EHCI Host Controller
238[ 3.356283] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
239[ 3.364229] ehci-platform 1c1c000.usb: irq 35, io mem 0x01c1c000
240[ 3.384032] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
241[ 3.390359] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
242[ 3.398632] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
243[ 3.405859] usb usb2: Product: EHCI Host Controller
244[ 3.410741] usb usb2: Manufacturer: Linux 5.10.16-sunxi ehci_hcd
245[ 3.416752] usb usb2: SerialNumber: 1c1c000.usb
246[ 3.421758] hub 2-0:1.0: USB hub found
247[ 3.425567] hub 2-0:1.0: 1 port detected
248[ 3.430483] ohci-platform 1c19400.usb: Generic Platform OHCI controller
249[ 3.437141] ohci-platform 1c19400.usb: new USB bus registered, assigned bus number 3
250[ 3.445058] ohci-platform 1c19400.usb: irq 34, io mem 0x01c19400
251[ 3.512218] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
252[ 3.520495] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
253[ 3.527719] usb usb3: Product: Generic Platform OHCI controller
254[ 3.533648] usb usb3: Manufacturer: Linux 5.10.16-sunxi ohci_hcd
255[ 3.539656] usb usb3: SerialNumber: 1c19400.usb
256[ 3.545500] hub 3-0:1.0: USB hub found
257[ 3.549299] hub 3-0:1.0: 1 port detected
258[ 3.554232] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
259[ 3.560902] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
260[ 3.568804] ohci-platform 1c1c400.usb: irq 36, io mem 0x01c1c400
261[ 3.636211] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
262[ 3.644495] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
263[ 3.651720] usb usb4: Product: Generic Platform OHCI controller
264[ 3.657651] usb usb4: Manufacturer: Linux 5.10.16-sunxi ohci_hcd
265[ 3.663659] usb usb4: SerialNumber: 1c1c400.usb
266[ 3.668799] hub 4-0:1.0: USB hub found
267[ 3.672607] hub 4-0:1.0: 1 port detected
268[ 3.679058] axp20x-i2c 2-0034: AXP20x variant AXP221 found
269[ 3.691992] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-2/2-0034/axp221-pek/input/input0
270[ 3.711441] vcc-3v3: supplied by regulator-dummy
271[ 3.716609] vdd-cpu: Bringing 1100000uV into 1160000-1160000uV
272[ 3.722936] vdd-cpu: supplied by regulator-dummy
273[ 3.728055] usb 1-1: new high-speed USB device number 2 using ehci-platform
274[ 3.735080] vdd-sys: Bringing 1100000uV into 1200000-1200000uV
275[ 3.741406] vdd-sys: supplied by regulator-dummy
276[ 3.746352] random: fast init done
277[ 3.750039] dcdc4: supplied by regulator-dummy
278[ 3.755149] vcc-dram: supplied by regulator-dummy
279[ 3.759960] vcc-lcd: failed to get the current voltage: -EPROBE_DEFER
280[ 3.766442] vcc-lcd: supplied by vcc-3v3
281[ 3.771558] dc5ldo: supplied by vcc-dram
282[ 3.776180] aldo1: supplied by regulator-dummy
283[ 3.781136] vcc-pa: Bringing 2500000uV into 1800000-1800000uV
284[ 3.787386] vcc-pa: supplied by regulator-dummy
285[ 3.793047] avcc: supplied by regulator-dummy
286[ 3.798090] eldo1: supplied by regulator-dummy
287[ 3.803258] vdd1v2-sata: supplied by regulator-dummy
288[ 3.808743] vcc-pe: Bringing 700000uV into 2800000-2800000uV
289[ 3.815200] vcc-pe: supplied by regulator-dummy
290[ 3.820258] vcc-wifi-io: Bringing 700000uV into 3300000-3300000uV
291[ 3.827169] vcc-wifi-io: supplied by regulator-dummy
292[ 3.832650] vcc-wifi: Bringing 700000uV into 3300000-3300000uV
293[ 3.838986] vcc-wifi: supplied by regulator-dummy
294[ 3.844195] vcc-wifi-2: Bringing 700000uV into 3300000-3300000uV
295[ 3.850692] vcc-wifi-2: supplied by regulator-dummy
296[ 3.856249] vdd2v5-sata: supplied by regulator-dummy
297[ 3.861449] rtc_ldo: supplied by regulator-dummy
298[ 3.867136] ldo_io0: supplied by regulator-dummy
299[ 3.872801] ldo_io1: supplied by regulator-dummy
300[ 3.878247] axp22x-adc: Failed to locate of_node [id: -1]
301[ 3.883866] axp20x-led: Failed to locate of_node [id: -1]
302[ 3.889394] axp20x-i2c 2-0034: AXP20X driver loaded
303[ 3.897402] 1c28c00.serial: ttyS1 at MMIO 0x1c28c00 (irq = 40, base_baud = 1500000) is a 16550A
304[ 3.897856] sunxi-mmc 1c0f000.mmc: Got CD GPIO
305[ 3.906335] serial serial0: tty port ttyS1 registered
306[ 3.916669] ahci-sunxi 1c18000.sata: supply target not found, using dummy regulator
307[ 3.924048] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, uses new timings mode
308[ 3.936260] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
309[ 3.980066] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
310[ 3.987574] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
311[ 3.993473] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
312[ 4.002458] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
313[ 4.011303] scsi host0: ahci-sunxi
314[ 4.015086] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 43
315[ 4.024046] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found
316[ 4.030440] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found
317[ 4.036589] dwmac-sun8i 1c50000.ethernet: supply phy-io not found, using dummy regulator
318[ 4.044922] dwmac-sun8i 1c50000.ethernet: PTP uses main clock
319[ 4.050719] dwmac-sun8i 1c50000.ethernet: Current syscon value is not the default 6 (expect 0)
320[ 4.059543] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supported
321[ 4.066801] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supported
322[ 4.074045] dwmac-sun8i 1c50000.ethernet: COE Type 2
323[ 4.079030] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported
324[ 4.085834] mmc0: host does not support reading read-only switch, assuming write-enable
325[ 4.093856] dwmac-sun8i 1c50000.ethernet: Normal descriptors
326[ 4.099539] dwmac-sun8i 1c50000.ethernet: Chain mode enabled
327[ 4.099568] mmc0: new high speed SDHC card at address 0001
328[ 4.105735] libphy: stmmac: probed
329[ 4.111892] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
330[ 4.121730] mmcblk0: p1
331[ 4.146657] of_cfs_init
332[ 4.149260] of_cfs_init: OK
333[ 4.152306] ALSA device list:
334[ 4.155279] No soundcards found.
335[ 4.184062] mmc1: new DDR MMC card at address 0001
336[ 4.190170] mmcblk1: mmc1:0001 Q2J55L 7.09 GiB
337[ 4.192085] usb 1-1: device descriptor read/64, error -71
338[ 4.195632] mmcblk1boot0: mmc1:0001 Q2J55L partition 1 16.0 MiB
339[ 4.206984] mmcblk1boot1: mmc1:0001 Q2J55L partition 2 16.0 MiB
340[ 4.215989] mmcblk1: p1
341[ 4.336048] ata1: SATA link down (SStatus 0 SControl 300)
342[ 4.344907] Freeing unused kernel memory: 1024K
343[ 4.349680] Run /init as init process
344[ 4.353357] with arguments:
345[ 4.353363] /init
346[ 4.353369] with environment:
347[ 4.353374] HOME=/
348[ 4.353378] TERM=linux
349[ 4.353384] ubootpart=e5ad4b56-01
350[ 4.353389] ubootsource=mmc
351[ 4.353394] sunxi_ve_mem_reserve=0
352[ 4.353400] sunxi_g2d_mem_reserve=0
353[ 4.353404] sunxi_fb_mem_reserve=16
354[ 4.353410] cgroup_enable=memory
355[ 4.656091] usb 1-1: device descriptor read/64, error -71
356[ 4.912379] sunxi-mmc 1c10000.mmc: allocated mmc-pwrseq
357[ 4.940128] sunxi-mmc 1c10000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
358[ 4.960697] sunxi-mmc 1c10000.mmc: no support for card's volts
359[ 4.966699] mmc2: error -22 whilst initialising SDIO card
360[ 5.104084] usb 1-1: new high-speed USB device number 3 using ehci-platform
361[ 5.456043] usb 1-1: device descriptor read/64, error -71
362[ 5.916059] usb 1-1: device descriptor read/64, error -71
363[ 6.028077] usb usb1-port1: attempt power cycle
364[ 6.684037] usb 1-1: new high-speed USB device number 4 using ehci-platform
365[ 7.108033] usb 1-1: device not accepting address 4, error -71
366[ 7.448030] usb 1-1: new high-speed USB device number 5 using ehci-platform
367[ 7.872033] usb 1-1: device not accepting address 5, error -71
368[ 7.877898] usb usb1-port1: unable to enumerate USB device
369[ 8.268079] usb 3-1: new full-speed USB device number 2 using ohci-platform
370[ 8.303692] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
371[ 8.495098] usb 3-1: not running at top speed; connect to a high speed hub
372[ 8.505093] usb 3-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
373[ 8.513354] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
374[ 8.523235] hub 3-1:1.0: USB hub found
375[ 8.528147] hub 3-1:1.0: 4 ports detected
376[ 8.836066] usb 3-1.3: new full-speed USB device number 3 using ohci-platform
377[ 8.961091] usb 3-1.3: not running at top speed; connect to a high speed hub
378[ 8.986084] usb 3-1.3: New USB device found, idVendor=1e0e, idProduct=9001, bcdDevice= 3.18
379[ 8.994510] usb 3-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
380[ 9.001828] usb 3-1.3: Product: SimTech, Incorporated
381[ 9.006884] usb 3-1.3: Manufacturer: SimTech, Incorporated
382[ 9.012377] usb 3-1.3: SerialNumber: 0123456789ABCDEF
383[ 9.036391] systemd[1]: System time before build time, advancing clock.
384[ 9.074070] systemd[1]: Inserted module 'autofs4'
385[ 9.100060] usb 3-1.4: new full-speed USB device number 4 using ohci-platform
386[ 9.159422] systemd[1]: systemd 245.4-4ubuntu3.4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
387[ 9.182610] systemd[1]: Detected architecture arm.
388[ 9.223087] usb 3-1.4: not running at top speed; connect to a high speed hub
389[ 9.242077] usb 3-1.4: New USB device found, idVendor=0bda, idProduct=b720, bcdDevice= 2.00
390[ 9.250449] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
391[ 9.257764] usb 3-1.4: Product: 802.11n WLAN Adapter
392[ 9.262742] usb 3-1.4: Manufacturer: Realtek
393[ 9.267057] usb 3-1.4: SerialNumber: 00e04c000001
394[ 9.273250] systemd[1]: Set hostname to <feta40i>.
395[ 9.675972] systemd[1]: /lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly.
396[ 9.902005] systemd[1]: /lib/systemd/system/gpsd.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/gpsd.sock → /run/gpsd.sock; please update the unit file accordingly.
397[ 10.144234] random: systemd: uninitialized urandom read (16 bytes read)
398[ 10.156294] systemd[1]: Created slice system-modprobe.slice.
399[ 10.176220] random: systemd: uninitialized urandom read (16 bytes read)
400[ 10.184574] systemd[1]: Created slice system-serial\x2dgetty.slice.
401[ 10.208221] random: systemd: uninitialized urandom read (16 bytes read)
402[ 10.216302] systemd[1]: Created slice User and Session Slice.
403[ 10.236223] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
404[ 10.249810] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
405[ 10.277283] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
406[ 10.304357] systemd[1]: Reached target Local Encrypted Volumes.
407[ 10.324502] systemd[1]: Reached target Remote File Systems.
408[ 10.344188] systemd[1]: Reached target Slices.
409[ 10.364229] systemd[1]: Reached target Swap.
410[ 10.384175] systemd[1]: Reached target System Time Set.
411[ 10.404898] systemd[1]: Listening on Syslog Socket.
412[ 10.424779] systemd[1]: Listening on fsck to fsckd communication Socket.
413[ 10.448459] systemd[1]: Listening on initctl Compatibility Named Pipe.
414[ 10.473290] systemd[1]: Listening on Journal Audit Socket.
415[ 10.496743] systemd[1]: Listening on Journal Socket (/dev/log).
416[ 10.520819] systemd[1]: Listening on Journal Socket.
417[ 10.540876] systemd[1]: Listening on udev Control Socket.
418[ 10.560595] systemd[1]: Listening on udev Kernel Socket.
419[ 10.580799] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
420[ 10.595168] systemd[1]: Mounting POSIX Message Queue File System...
421[ 10.626589] systemd[1]: Mounting Kernel Debug File System...
422[ 10.654399] systemd[1]: Mounting Kernel Trace File System...
423[ 10.684243] systemd[1]: Starting Restore / save the current clock...
424[ 10.715135] systemd[1]: Starting Set the console keyboard layout...
425[ 10.744840] systemd[1]: Starting Create list of static device nodes for the current kernel...
426[ 10.772541] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped.
427[ 10.788487] systemd[1]: Started Nameserver information manager.
428[ 10.813168] systemd[1]: Reached target Network (Pre).
429[ 10.834871] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
430[ 10.844340] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
431[ 10.862440] systemd[1]: Starting Load Kernel Modules...
432[ 10.891583] systemd[1]: Starting Remount Root and Kernel File Systems...
433[ 10.923423] systemd[1]: Starting udev Coldplug all Devices...
434[ 10.935965] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro
435[ 10.955597] systemd[1]: Mounted POSIX Message Queue File System.
436[ 10.977266] systemd[1]: Mounted Kernel Debug File System.
437[ 11.001269] systemd[1]: Mounted Kernel Trace File System.
438[ 11.027740] systemd[1]: Finished Restore / save the current clock.
439[ 11.052663] systemd[1]: Finished Create list of static device nodes for the current kernel.
440[ 11.086738] systemd[1]: Finished Load Kernel Modules.
441[ 11.111703] systemd[1]: Finished Remount Root and Kernel File Systems.
442[ 11.144333] systemd[1]: Finished Set the console keyboard layout.
443[ 11.176315] systemd[1]: Mounting FUSE Control File System...
444[ 11.202586] systemd[1]: Mounting Kernel Configuration File System...
445[ 11.226408] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
446[ 11.235367] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
447[ 11.250797] systemd[1]: Starting Load/Save Random Seed...
448[ 11.279034] systemd[1]: Starting Apply Kernel Variables...
449[ 11.306891] systemd[1]: Starting Create System Users...
450[ 11.334909] systemd[1]: Mounted FUSE Control File System.
451[ 11.357370] systemd[1]: Mounted Kernel Configuration File System.
452[ 11.378589] systemd[1]: Finished Apply Kernel Variables.
453[ 11.399920] systemd[1]: Finished Create System Users.
454[ 11.419845] systemd[1]: Finished udev Coldplug all Devices.
455[ 11.444232] systemd[1]: Starting Helper to synchronize boot up for ifupdown...
456[ 11.466553] systemd[1]: Starting Create Static Device Nodes in /dev...
457[ 11.488122] systemd[1]: Finished Helper to synchronize boot up for ifupdown.
458[ 11.526511] systemd[1]: Finished Create Static Device Nodes in /dev.
459[ 11.545046] systemd[1]: Reached target Local File Systems (Pre).
460[ 11.566835] systemd[1]: Mounting /tmp...
461[ 11.588089] systemd[1]: Starting udev Kernel Device Manager...
462[ 11.610026] systemd[1]: Mounted /tmp.
463[ 11.625200] systemd[1]: Reached target Local File Systems.
464[ 11.646376] systemd[1]: Starting Armbian ZRAM config...
465[ 11.666421] systemd[1]: Starting Set console font and keymap...
466[ 11.686771] systemd[1]: Starting Raise network interfaces...
467[ 11.700679] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
468[ 11.705072] systemd[1]: Finished Set console font and keymap.
469[ 11.931556] systemd[1]: Started udev Kernel Device Manager.
470[ 12.023149] zram: Added device: zram0
471[ 12.027345] zram: Added device: zram1
472[ 12.028237] zram: Added device: zram2
473[ 12.040175] systemd[1]: Finished Raise network interfaces.
474[ 12.229615] zram0: detected capacity change from 0 to 523755520
475[ 12.556500] usbcore: registered new interface driver usbserial_generic
476[ 12.556578] usbserial: USB Serial support registered for generic
477[ 12.557158] systemd[1]: Found device /dev/ttyS0.
478[ 12.644396] usbcore: registered new interface driver cdc_wdm
479[ 12.648439] usbcore: registered new interface driver option
480[ 12.648524] usbserial: USB Serial support registered for GSM modem (1-port)
481[ 12.649112] option 3-1.3:1.0: GSM modem (1-port) converter detected
482[ 12.653596] usb 3-1.3: GSM modem (1-port) converter now attached to ttyUSB0
483[ 12.654028] option 3-1.3:1.1: GSM modem (1-port) converter detected
484[ 12.654586] usb 3-1.3: GSM modem (1-port) converter now attached to ttyUSB1
485[ 12.654956] option 3-1.3:1.2: GSM modem (1-port) converter detected
486[ 12.655400] usb 3-1.3: GSM modem (1-port) converter now attached to ttyUSB2
487[ 12.655810] option 3-1.3:1.3: GSM modem (1-port) converter detected
488[ 12.656377] usb 3-1.3: GSM modem (1-port) converter now attached to ttyUSB3
489[ 12.656769] option 3-1.3:1.4: GSM modem (1-port) converter detected
490[ 12.657287] usb 3-1.3: GSM modem (1-port) converter now attached to ttyUSB4
491[ 12.685638] qmi_wwan 3-1.3:1.5: cdc-wdm0: USB WDM device
492[ 12.733476] qmi_wwan 3-1.3:1.5 wwan0: register 'qmi_wwan' at usb-1c19400.usb-1.3, WWAN/QMI device, da:d8:44:f6:43:d2
493[ 12.740523] usbcore: registered new interface driver qmi_wwan
494[ 12.752417] Bluetooth: Core ver 2.22
495[ 12.752537] NET: Registered protocol family 31
496[ 12.752544] Bluetooth: HCI device and connection manager initialized
497[ 12.752567] Bluetooth: HCI socket layer initialized
498[ 12.752620] Bluetooth: L2CAP socket layer initialized
499[ 12.752650] Bluetooth: SCO socket layer initialized
500[ 12.875823] cfg80211: Loading compiled-in X.509 certificates for regulatory database
501[ 12.877049] usbcore: registered new interface driver btusb
502[ 12.878441] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
503[ 12.892169] Bluetooth: HCI UART driver ver 2.3
504[ 12.892202] Bluetooth: HCI UART protocol H4 registered
505[ 12.892222] Bluetooth: HCI UART protocol BCSP registered
506[ 12.892485] Bluetooth: HCI UART protocol LL registered
507[ 12.892507] Bluetooth: HCI UART protocol ATH3K registered
508[ 12.892672] Bluetooth: HCI UART protocol Three-wire (H5) registered
509[ 12.893201] Bluetooth: HCI UART protocol Broadcom registered
510[ 12.893590] sun4i-pinctrl 1c20800.pinctrl: supply vcc-ph not found, using dummy regulator
511[ 12.905265] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
512[ 12.910637] Bluetooth: hci0: RTL: rom_version status=0 version=1
513[ 12.910659] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_fw.bin
514[ 12.948891] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723b_config.bin
515[ 12.952212] Bluetooth: hci0: RTL: cfg_sz 68, total sz 24088
516[ 13.023854] usb 3-1.4: This Realtek USB WiFi dongle (0x0bda:0xb720) is untested!
517[ 13.023872] usb 3-1.4: Please report results to Jes.Sorensen@gmail.com
518[ 13.119831] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
519[ 13.121111] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
520[ 13.121761] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
521[ 13.122217] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
522[ 13.122513] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
523[ 13.122731] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
524[ 13.376156] Adding 511476k swap on /dev/zram0. Priority:5 extents:1 across:511476k SSFS
525[ 13.545172] Bluetooth: hci0: RTL: fw version 0x1e4cc3ff
526[ 13.568161] random: crng init done
527[ 13.568181] random: 7 urandom warning(s) missed due to ratelimiting
528[ 13.586384] systemd[1]: Finished Load/Save Random Seed.
529[ 13.598036] zram1: detected capacity change from 0 to 52428800
530[ 13.667584] systemd[1]: Finished Armbian ZRAM config.
531[ 13.680945] systemd[1]: Reached target Bluetooth.
532[ 13.696622] systemd[1]: Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
533[ 13.718396] systemd[1]: Starting Armbian memory supported logging...
534[ 13.736456] systemd[1]: Condition check resulted in Store a System Token in an EFI Variable being skipped.
535[ 13.744372] systemd[1]: Starting Load/Save RF Kill Switch Status...
536[ 13.784867] systemd[1]: Started Load/Save RF Kill Switch Status.
537[ 13.820572] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
538[ 13.820625] ext4 filesystem being mounted at /var/log supports timestamps until 2038 (0x7fffffff)
539[ 15.132062] Bluetooth: hci1: command 0xfc18 tx timeout
540[ 15.178095] usb 3-1.4: Vendor: Realtek
541[ 15.178109] usb 3-1.4: Product: 802.11n WLAN Adapter
542[ 15.178118] usb 3-1.4: rtl8723bu_parse_efuse: dumping efuse (0x200 bytes):
543[ 15.178126] usb 3-1.4: 00: 29 81 03 7c 01 08 21 00
544[ 15.178134] usb 3-1.4: 08: 40 07 05 35 10 00 00 00
545[ 15.178141] usb 3-1.4: 10: 35 35 35 34 33 33 34 34
546[ 15.178148] usb 3-1.4: 18: 34 33 32 02 ff ff ff ff
547[ 15.178155] usb 3-1.4: 20: ff ff ff ff ff ff ff ff
548[ 15.178162] usb 3-1.4: 28: ff ff ff ff ff ff ff ff
549[ 15.178169] usb 3-1.4: 30: ff ff ff ff ff ff ff ff
550[ 15.178177] usb 3-1.4: 38: ff ff 35 35 35 34 33 33
551[ 15.178184] usb 3-1.4: 40: 34 34 34 33 32 02 ff ff
552[ 15.178191] usb 3-1.4: 48: ff ff ff ff ff ff ff ff
553[ 15.178198] usb 3-1.4: 50: ff ff ff ff ff ff ff ff
554[ 15.178205] usb 3-1.4: 58: ff ff ff ff ff ff ff ff
555[ 15.178212] usb 3-1.4: 60: ff ff ff ff ff ff ff ff
556[ 15.178220] usb 3-1.4: 68: ff ff ff ff ff ff ff ff
557[ 15.178227] usb 3-1.4: 70: ff ff ff ff ff ff ff ff
558[ 15.178234] usb 3-1.4: 78: ff ff ff ff ff ff ff ff
559[ 15.178241] usb 3-1.4: 80: ff ff ff ff ff ff ff ff
560[ 15.178249] usb 3-1.4: 88: ff ff ff ff ff ff ff ff
561[ 15.178256] usb 3-1.4: 90: ff ff ff ff ff ff ff ff
562[ 15.178263] usb 3-1.4: 98: ff ff ff ff ff ff ff ff
563[ 15.178270] usb 3-1.4: a0: ff ff ff ff ff ff ff ff
564[ 15.178277] usb 3-1.4: a8: ff ff ff ff ff ff ff ff
565[ 15.178284] usb 3-1.4: b0: ff ff ff ff ff ff ff ff
566[ 15.178291] usb 3-1.4: b8: 20 0e 20 00 00 00 ff ff
567[ 15.178298] usb 3-1.4: c0: ff 28 20 11 00 00 00 ff
568[ 15.178306] usb 3-1.4: c8: 00 ff ff ff ff ff ff ff
569[ 15.178313] usb 3-1.4: d0: ff ff ff ff ff ff ff ff
570[ 15.178320] usb 3-1.4: d8: ff ff ff ff ff ff ff ff
571[ 15.178327] usb 3-1.4: e0: ff ff ff ff ff ff ff ff
572[ 15.178334] usb 3-1.4: e8: ff ff ff ff ff ff ff ff
573[ 15.178342] usb 3-1.4: f0: ff ff ff ff ff ff ff ff
574[ 15.178349] usb 3-1.4: f8: ff ff ff ff ff ff ff ff
575[ 15.178357] usb 3-1.4: 100: da 0b 20 b7 e7 47 03 38
576[ 15.178364] usb 3-1.4: 108: 01 46 dc 69 58 09 03 52
577[ 15.178371] usb 3-1.4: 110: 65 61 6c 74 65 6b 16 03
578[ 15.178378] usb 3-1.4: 118: 38 30 32 2e 31 31 6e 20
579[ 15.178386] usb 3-1.4: 120: 57 4c 41 4e 20 41 64 61
580[ 15.178393] usb 3-1.4: 128: 70 74 65 72 00 ff ff ff
581[ 15.178400] usb 3-1.4: 130: ff ff ff ff ff ff ff ff
582[ 15.178407] usb 3-1.4: 138: ff ff ff ff ff ff ff ff
583[ 15.178414] usb 3-1.4: 140: ff ff ff ff ff ff ff 0f
584[ 15.178422] usb 3-1.4: 148: ff ff ff ff ff ff ff ff
585[ 15.178429] usb 3-1.4: 150: ff ff ff ff ff ff ff ff
586[ 15.178436] usb 3-1.4: 158: ff ff ff ff ff ff ff ff
587[ 15.178443] usb 3-1.4: 160: ff ff ff ff ff ff ff ff
588[ 15.178451] usb 3-1.4: 168: ff ff ff ff ff ff ff ff
589[ 15.178458] usb 3-1.4: 170: ff ff ff ff ff ff ff ff
590[ 15.178465] usb 3-1.4: 178: ff ff ff ff ff ff ff ff
591[ 15.178473] usb 3-1.4: 180: ff ff ff ff ff ff ff ff
592[ 15.178480] usb 3-1.4: 188: ff ff ff ff ff ff ff ff
593[ 15.178487] usb 3-1.4: 190: ff ff ff ff ff ff ff ff
594[ 15.178494] usb 3-1.4: 198: ff ff ff ff ff ff ff ff
595[ 15.178502] usb 3-1.4: 1a0: ff ff ff ff ff ff ff ff
596[ 15.178509] usb 3-1.4: 1a8: ff ff ff ff ff ff ff ff
597[ 15.178516] usb 3-1.4: 1b0: ff ff ff ff ff ff ff ff
598[ 15.178523] usb 3-1.4: 1b8: ff ff ff ff ff ff ff ff
599[ 15.178531] usb 3-1.4: 1c0: ff ff ff ff ff ff ff ff
600[ 15.178538] usb 3-1.4: 1c8: ff ff ff ff ff ff ff ff
601[ 15.178545] usb 3-1.4: 1d0: ff ff ff ff ff ff ff ff
602[ 15.178552] usb 3-1.4: 1d8: ff ff ff ff ff ff ff ff
603[ 15.178560] usb 3-1.4: 1e0: ff ff ff ff ff ff ff ff
604[ 15.178567] usb 3-1.4: 1e8: ff ff ff ff ff ff ff ff
605[ 15.178574] usb 3-1.4: 1f0: ff ff ff ff ff ff ff ff
606[ 15.178581] usb 3-1.4: 1f8: ff ff ff ff ff ff ff ff
607[ 15.178594] usb 3-1.4: RTL8723BU rev E (SMIC) 1T1R, TX queues 3, WiFi=1, BT=1, GPS=0, HI PA=0
608[ 15.178604] usb 3-1.4: RTL8723BU MAC: 38:01:46:dc:69:58
609[ 15.178612] usb 3-1.4: rtl8xxxu: Loading firmware rtlwifi/rtl8723bu_nic.bin
610[ 15.182185] usb 3-1.4: Firmware revision 35.0 (signature 0x5301)
611[ 17.744995] systemd[1]: Finished Armbian memory supported logging.
612[ 17.773869] systemd[1]: Starting Journal Service...
613[ 18.211385] systemd[1]: Started Journal Service.
614[ 18.266476] systemd-journald[453]: Received client request to flush runtime journal.
615[ 18.411085] usbcore: registered new interface driver rtl8xxxu
616[ 18.434529] rtl8xxxu 3-1.4:1.2 wlx380146dc6958: renamed from wlan0
617[ 21.440209] dwmac-sun8i 1c50000.ethernet eth0: PHY [stmmac-0:01] driver [ICPlus IP101A/G] (irq=POLL)
618[ 21.443836] dwmac-sun8i 1c50000.ethernet eth0: No Safety Features support found
619[ 21.443871] dwmac-sun8i 1c50000.ethernet eth0: No MAC Management Counters available
620[ 21.443888] dwmac-sun8i 1c50000.ethernet eth0: PTP not supported by HW
621[ 21.454178] dwmac-sun8i 1c50000.ethernet eth0: configuring for phy/rgmii-id link mode
622[ 23.356212] Bluetooth: hci1: BCM: failed to write update baudrate (-110)
623[ 23.356230] Bluetooth: hci1: Failed to set baudrate
624[ 24.552325] dwmac-sun8i 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
625[ 24.552375] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
626[ 25.372308] Bluetooth: hci1: command 0x0c03 tx timeout
627[ 33.596653] Bluetooth: hci1: BCM: Reset failed (-110)
628[ 35.900759] vcc-lcd: disabling
629[ 35.901113] dc5ldo: disabling