· 10 years ago · May 27, 2016, 10:06 AM
1-Boot 2015.07-g7e2f081-dirty (Mar 18 2016 - 10:21:25 +0800)S900 96BOARD
2
3DRAM: 2 GiB
4Relocation Offset is: 6ef48000
5PMU_INFO:found PMIC type 2 ver 3
6clk: core_pll 1104MHz, dev_pll 660MHz, display_pll 1056MHz
7MMC: MMC: source clk CMU_DEVPLL:660000000Hz
8MMC: source clk CMU_DEVPLL:660000000Hz
9host0 scan ok
10MMC: source clk CMU_DEVPLL:660000000Hz
11error: SDC2 send CMD8, No rsp
12error: SDC2 send CMD55, No rsp
13MMC: source clk CMU_DEVPLL:660000000Hz
14phy_mmca init ok
15virmmc1: 0, virmmc0: 1
16Using default environment
17
18check recovery mode
19** Invalid partition 6 **
20check update.zip in sdcard
21ERROR: owl_lcdc: no etry for 'panel_configs'
22
23at /home/local/ACTIONS/liuwei/ad900/bf1_tag_151209/u-boot/drivers/video/owl/dss/controller/lcdc.c:71/lcdc_parse_config)
24ERROR: owl_edpc: no etry for 'panel_configs'
25
26at /home/local/ACTIONS/liuwei/ad900/bf1_tag_151209/u-boot/drivers/video/owl/dss/controller/edpc.c:66/edpc_parse_config)
27transfer error
28ERROR: owl_fb: no primary panel
29
30at /home/local/ACTIONS/liuwei/ad900/bf1_tag_151209/u-boot/drivers/video/owl/owl_fb.c:156/owl_fb_init()
31In: uart@e012a000
32Out: serial
33Err: serial
34adckey: AUX0, channel=0
35adckey: keynum=2
36adc_val=3852
37check_key: keycode=-1
38Net: usb_ether
39Warning: usb_ether (eth0) using random MAC address - 56:79:41:43:6f:ef
40
41Hit any key to stop autoboot: 0
42boot from mmc card ...
43reading uEnv.txt
44718 bytes read in 5 ms (139.6 KiB/s)
45Loaded environment from uEnv.txt
46reading boot.scr
47** Unable to read file boot.scr **
48reading bubblegum-kernel_0.snap/Image
4911747912 bytes read in 589 ms (19 MiB/s)
50reading ramdisk.img
51** Unable to read file ramdisk.img **
52reading bubblegum-kernel_0.snap/dtbs/s900_96board.dtb
5329979 bytes read in 9 ms (3.2 MiB/s)
54Image lacks image_size field, assuming 16MiB
55Wrong Ramdisk Image Format
56Ramdisk image is corrupt or invalid
57owl> run bootsnappy
58reading bubblegum-kernel_0.snap/Image
5911747912 bytes read in 590 ms (19 MiB/s)
60reading bubblegum-kernel_0.snap/dtbs/s900_96board.dtb
6129979 bytes read in 9 ms (3.2 MiB/s)
62reading bubblegum-kernel_0.snap/uInitrd
633756192 bytes read in 190 ms (18.9 MiB/s)
64Image lacks image_size field, assuming 16MiB
65## Loading init Ramdisk from Legacy Image at 01ffffc0 ...
66 Image Name: Snappy Initrd
67 Image Type: AArch64 Linux RAMDisk Image (uncompressed)
68 Data Size: 3756128 Bytes = 3.6 MiB
69 Load Address: 01ffffc0
70 Entry Point: 01ffffc0
71 Verifying Checksum ... OK
72## Flattened Device Tree blob at 10000000
73 Booting using the fdt blob at 0x10000000
74 reserving fdt memory region: addr=19000000 size=3000000
75 reserving fdt memory region: addr=20000000 size=20000000
76 reserving fdt memory region: addr=18fff000 size=1000
77 reserving fdt memory region: addr=1f000000 size=1000000
78 Using Device Tree in place at 0000000010000000, end 000000001000a51a
79read_mi_head, line 467, magic 0x0, length 0, item num 0
80read Head null
81read bf-sn faild,errorcode:-1,
82
83Starting kernel ...
84
85[ 0.000000] Initializing cgroup subsys cpuset
86[ 0.000000] Initializing cgroup subsys cpu
87[ 0.000000] Initializing cgroup subsys cpuacct
88[ 0.000000] Linux version 3.10.52 (josh@josh-ThinkPad-T420) (gcc version 4.9.3 20141031 (prerelease) (Linaro GCC 206
89[ 0.000000] CPU: AArch64 Processor [410fd032] revision 2
90[ 0.000000] Machine: s900
91[ 0.000000] efi: Getting EFI parameters from FDT:
92[ 0.000000] efi: UEFI not found.
93[ 0.000000] cma: CMA: reserved 64 MiB at 7c000000
94[ 0.000000] psci: probing function IDs from device-tree
95[ 0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc07bfa2000 s19776 r8192 d21184 u49152
96[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517120
97[ 0.000000] Kernel command line: console=ttyS5,115200n8 initcall_debug root=/dev/disk/by-label/writable init=/lib/st
98[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
99[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
100[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
101[ 0.000000] Memory: 2048MB = 2048MB total
102[ 0.000000] Memory: 1393612k/1393612k available, 703540k reserved
103[ 0.000000] Virtual kernel memory layout:
104[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB)
105[ 0.000000] vmemmap : 0xffffffbc00000000 - 0xffffffbc01c00000 ( 28 MB)
106[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
107[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc080000000 ( 2048 MB)
108[ 0.000000] .init : 0xffffffc000aac000 - 0xffffffc000b09d40 ( 376 kB)
109[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc000aabbf4 ( 10415 kB)
110[ 0.000000] .data : 0xffffffc000b0a000 - 0xffffffc000bb4248 ( 681 kB)
111[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
112[ 0.000000] Preemptible hierarchical RCU implementation.
113[ 0.000000] NR_IRQS:64 nr_irqs:64 0
114[ 0.000000] [OWL] init sirqs, nr_sirq 3
115[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
116[ 0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
117[ 0.000000] [OWL] timer initialization
118[ 0.000000] Console: colour dummy device 80x25
119[ 0.000000] allocated 8388608 bytes of page_cgroup
120[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
121[ 0.002374] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
122[ 0.002374] pid_max: default: 32768 minimum: 301
123[ 0.002468] Security Framework initialized
124[ 0.002499] SELinux: Disabled at boot.
125[ 0.002499] AppArmor: AppArmor disabled by boot time parameter
126[ 0.002531] Mount-cache hash table entries: 256
127[ 0.006593] Initializing cgroup subsys debug
128[ 0.006593] Initializing cgroup subsys memory
129[ 0.006624] Initializing cgroup subsys devices
130[ 0.006624] Initializing cgroup subsys freezer
131[ 0.006843] /cpus/cpu@0: Missing clock-frequency property
132[ 0.006843] /cpus/cpu@1: Missing clock-frequency property
133[ 0.006843] /cpus/cpu@2: Missing clock-frequency property
134[ 0.006874] /cpus/cpu@3: Missing clock-frequency property
135[ 0.006937] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
136[ 0.006968] EFI services will not be available.
137[ 0.060187] CPU1: Booted secondary processor
138[ 0.080156] CPU2: Booted secondary processor
139[ 0.100156] CPU3: Booted secondary processor
140[ 0.100281] Brought up 4 CPUs
141[ 0.100281] SMP: Total of 4 processors activated (192.00 BogoMIPS).
142[ 0.100843] devtmpfs: initialized
143[ 0.104468] pinctrl core: initialized pinctrl subsystem
144[ 0.104718] regulator-dummy: no parameters
145[ 0.106187] NET: Registered protocol family 16
146[ 0.107124] vdso: 2 pages (1 code, 1 data) at base ffffffc000b11000
147[ 0.107187] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
148[ 0.108343] software IO TLB [mem 0x78c00000-0x79000000] (4MB) mapped at [ffffffc078c00000-ffffffc078ffffff]
149[ 0.108406] requeue_bios init work
150[ 0.108406] scan_work init work
151[ 0.109468] DMA: preallocated 256 KiB pool for atomic allocations
152[ 0.109624] [OWL] Power domain initialization
153[ 0.109749] [OWL] S900 clock initialization
154[ 0.110812] [OWL] pinctrl initialization
155[ 0.110843] pinctrl-s900 e01b0000.pinctrl: nfunctions 49, ngroups 94
156[ 0.112312] [OWL] register reset controller
157[ 0.112781] GPIOA initialization
158[ 0.113249] GPIOB initialization
159[ 0.113687] GPIOC initialization
160[ 0.114187] GPIOD initialization
161[ 0.114687] GPIOE initialization
162[ 0.115156] GPIOF initialization
163[ 0.123812] bio: create slab <bio-0> at 0
164[ 0.124468] [OWL] initialize DMA controller
165[ 0.124499] dma-owl e0260000.dma-controller: dma-channels 12, dma-requests 46
166[ 0.127218] eta355c_init 297
167[ 0.127437] gpu-gpio-supply: 875 <--> 1000 mV at 1000 mV
168[ 0.128312] SCSI subsystem initialized
169[ 0.128343] [OWL] SPI controller initialization
170[ 0.128593] usbcore: registered new interface driver usbfs
171[ 0.128624] usbcore: registered new interface driver hub
172[ 0.128687] usbcore: registered new device driver usb
173[ 0.128843] [OWL] I2C controller initialization
174[ 0.129437] i2c-owl e0170000.i2c: I2C adapter ready to operate.
175[ 0.129749] i2c-owl e0172000.i2c: I2C adapter ready to operate.
176[ 0.129874] i2c-owl e0174000.i2c: I2C adapter ready to operate.
177[ 0.130187] atc260x_i2c 3-0065: Probing...
178[ 0.130249] atc260x_i2c 3-0065: atc260x_core_dev_init() enter
179[ 0.131656] atc260x_i2c 3-0065: detect PMU chip type 2 ver D
180[ 0.131656] atc260x_i2c 3-0065: PMU root IRQ 130
181[ 0.132249] atc260x-regulator atc2609a-dcdc0.0: Probing atc2609a-dcdc0, id=0
182[ 0.133437] dcdc0: 600 <--> 1300 mV at 925 mV
183[ 0.133749] atc260x-regulator atc2609a-dcdc1.1: Probing atc2609a-dcdc1, id=1
184[ 0.134906] dcdc1: 600 <--> 1300 mV at 925 mV
185[ 0.135187] atc260x-regulator atc2609a-dcdc2.2: Probing atc2609a-dcdc2, id=2
186[ 0.136374] dcdc2: 600 <--> 1350 mV at 1300 mV
187[ 0.136656] atc260x-regulator atc2609a-dcdc3.3: Probing atc2609a-dcdc3, id=3
188[ 0.137843] dcdc3: 600 <--> 3500 mV at 3100 mV
189[ 0.138156] atc260x-regulator atc2609a-dcdc4.4: Probing atc2609a-dcdc4, id=4
190[ 0.139312] dcdc4: 600 <--> 1300 mV at 925 mV
191[ 0.139593] atc260x-regulator atc2609a-ldo0.0: Probing atc2609a-ldo0, id=0
192[ 0.141968] ldo0: 2300 <--> 3400 mV at 3100 mV
193[ 0.142281] atc260x-regulator atc2609a-ldo1.1: Probing atc2609a-ldo1, id=1
194[ 0.142499] ldo1: 2300 <--> 3400 mV at 3100 mV
195[ 0.142812] atc260x-regulator atc2609a-ldo2.2: Probing atc2609a-ldo2, id=2
196[ 0.145156] ldo2: 2300 <--> 3400 mV at 3100 mV
197[ 0.145468] atc260x-regulator atc2609a-ldo3.3: Probing atc2609a-ldo3, id=3
198[ 0.145468] atc260x-regulator atc2609a-ldo3.3: attemp to change volt band to #0
199[ 0.147968] ldo3: 700 <--> 2200 mV at 1800 mV
200[ 0.148281] atc260x-regulator atc2609a-ldo4.4: Probing atc2609a-ldo4, id=4
201[ 0.148281] atc260x-regulator atc2609a-ldo4.4: attemp to change volt band to #0
202[ 0.150749] ldo4: 700 <--> 2200 mV at 1800 mV
203[ 0.151156] atc260x-regulator atc2609a-ldo6.6: Probing atc2609a-ldo6, id=6
204[ 0.151156] atc260x-regulator atc2609a-ldo6.6: attemp to change volt band to #0
205[ 0.153656] ldo6: 850 <--> 2200 mV at 1050 mV
206[ 0.153968] atc260x-regulator atc2609a-ldo7.7: Probing atc2609a-ldo7, id=7
207[ 0.153968] atc260x-regulator atc2609a-ldo7.7: attemp to change volt band to #0
208[ 0.154343] ldo7: 700 <--> 2200 mV at 1800 mV
209[ 0.154624] atc260x-regulator atc2609a-ldo8.8: Probing atc2609a-ldo8, id=8
210[ 0.154656] atc260x-regulator atc2609a-ldo8.8: attemp to change volt band to #1
211[ 0.155124] ldo8: 2100 <--> 3300 mV at 3200 mV
212[ 0.155437] atc260x-regulator atc2609a-ldo9.9: Probing atc2609a-ldo9, id=9
213[ 0.157624] ldo9: 2600 <--> 3300 mV at 3100 mV
214[ 0.158812] atc260x-pm atc2609a-pm.0: Probing...
215[ 0.158812] atc260x-pm atc2609a-pm.0: _atc260x_pm_set_wakeup_src_inner() enter, mask=0x7fff src=0x706
216[ 0.159124] atc260x-pm atc2609a-pm.0: _atc260x_pm_set_wakeup_src_inner() setup reg=0x0 msk=0xffe0 val=0xe0c0 readba5
217[ 0.159281] atc260x-pm atc2609a-pm.0: _atc260x_pm_set_wakeup_src_inner() enter, mask=0x8 src=0x0
218[ 0.159562] atc260x-pm atc2609a-pm.0: _atc260x_pm_set_wakeup_src_inner() setup reg=0x0 msk=0x100 val=0x0 readback=05
219[ 0.160156] atc260x-pm atc2609a-pm.0: _clear_status() no need to restore old alarm
220[ 0.161031] atc260x-pm atc2609a-pm.0: atc260x_pm_setup_wall_vbus_wakup_function() can not get of_property support_a
221[ 0.161031] atc260x-pm atc2609a-pm.0: atc260x_pm_probe() setup_wall_vbus_wakup_function failed
222[ 0.161312] atc260x-pm atc2609a-pm.0: translated wakeup falgs: 0x2
223[ 0.161374] [PM] set pmic suspend ops 0xffffffc000b58b68
224[ 0.161499] atc260x-pm atc2609a-pm.0: #####atc260x_pm_probe PMU_SYS_CTL0:0xe0d5 ####
225[ 0.161531] atc260x_i2c 3-0065: atc260x_core_dev_init() exit
226[ 0.161531] i2c-owl e0176000.i2c: I2C adapter ready to operate.
227[ 0.161906] i2c-owl e0178000.i2c: I2C adapter ready to operate.
228[ 0.161999] media: Linux media interface: v0.10
229[ 0.162062] Linux video capture interface: v2.00
230[ 0.162749] [OWL] ion_heap_fb: base 0x0, size 0x0
231[ 0.162749] [OWL] ion_heap_pmem: base 0x20000000, size 0x20000000
232[ 0.162749] [OWL] ion_heap_reserved: base 0x0, size 0x0
233[ 0.172031] Advanced Linux Sound Architecture Driver Initialized.
234[ 0.172593] Bluetooth: Core ver 2.16
235[ 0.172624] NET: Registered protocol family 31
236[ 0.172624] Bluetooth: HCI device and connection manager initialized
237[ 0.172656] Bluetooth: HCI socket layer initialized
238[ 0.172656] Bluetooth: L2CAP socket layer initialized
239[ 0.172656] Bluetooth: SCO socket layer initialized
240[ 0.172906] cfg80211: Calling CRDA to update world regulatory domain
241[ 0.173374] NetLabel: Initializing
242[ 0.173374] NetLabel: domain hash size = 128
243[ 0.173406] NetLabel: protocols = UNLABELED CIPSOv4
244[ 0.173437] NetLabel: unlabeled traffic allowed by default
245[ 0.173812] Switching to clocksource arch_sys_counter
246[ 0.198124] NET: Registered protocol family 2
247[ 0.198562] TCP established hash table entries: 16384 (order: 6, 262144 bytes)
248[ 0.198812] TCP bind hash table entries: 16384 (order: 7, 524288 bytes)
249[ 0.199156] TCP: Hash tables configured (established 16384 bind 16384)
250[ 0.199218] TCP: reno registered
251[ 0.199218] UDP hash table entries: 1024 (order: 4, 98304 bytes)
252[ 0.199281] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes)
253[ 0.199562] NET: Registered protocol family 1
254[ 0.199749] Trying to unpack rootfs image as initramfs...
255[ 0.361031] Freeing initrd memory: 3668K (ffffffc002000000 - ffffffc002395000)
256[ 0.362218] audit: initializing netlink socket (disabled)
257[ 0.362249] type=2000 audit(0.350:1): initialized
258[ 0.367718] VFS: Disk quotas dquot_6.5.2
259[ 0.367906] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
260[ 0.369406] squashfs: version 4.0 (2009/01/31) Phillip Lougher
261[ 0.369656] exFAT: Version 1.2.9
262[ 0.370718] fuse init (API version 7.22)
263[ 0.371062] msgmni has been set to 3881
264[ 0.373062] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
265[ 0.373093] io scheduler noop registered
266[ 0.373093] io scheduler deadline registered
267[ 0.373218] io scheduler cfq registered (default)
268[ 0.373437] pwm-owl e01b0000.pwm: owl_pwm_probe
269[ 0.373468] pwm-owl e01b0000.pwm: pc->baseffffff800006c000
270[ 0.373749] owl_dss_core: owl_dss_init, start
271[ 0.373749] owl_ctrl: owl_ctrl_init, start
272[ 0.373749] owl_panel: owl_panel_init, start
273[ 0.373781] owl_de_s900_init
274[ 0.373999] de-s900 e02e0000.de: de_s900_probe, pdev = 0xffffffc079e54400
275[ 0.374031] owl_de: owl_de_register, start
276[ 0.376062] de-s900 e02e0000.de: de_s900_device_power_on
277[ 0.379343] owl_de_mmu: owl_de_mmu_init, base 0xffffff800007a000 base_phys 0x7c100000 mmu.addr 0xffffff800007a000
278[ 0.379343] owl_de: owl_de_debugfs_create, start
279[ 0.379968] ip_sx00_platform_init
280[ 0.380062] hdmi-ip-sx00 e0250000.hdmi: ip_sx00_probe
281[ 0.380093] hdmi_ip_register
282[ 0.380249] owl_ctrl: owl_ctrl_register, start
283[ 0.380281] hdmi_ddc: hdmi_iic_probe, OK
284[ 0.380499] panel_ghp_init
285[ 0.380562] panel-ghp hdmi_panel.3: panel_ghp_probe
286[ 0.380562] owl_panel: owl_panel_parse_panel_info, start
287[ 0.380562] owl_panel: owl_panel_parse_panel_info, no entry for 'videomode-0'
288[ 0.380562] owl_panel: owl_panel_register, start
289[ 0.380656] owl_ctrl: owl_ctrl_add_panel, start
290[ 0.380656] hdmi-ip-sx00 e0250000.hdmi: owl_hdmic_add_panel, default video mode() invalid
291[ 0.380781] owl_fb_init
292[ 0.380874] owl-fb framebuffer.7: owl_fb_probe
293[ 0.384437] owl_panel: owl_panel_enable, state 2, power_on_delay 0, enable_delay 0
294[ 0.384437] owl_ctrl: owl_ctrl_enable, start
295[ 0.384468] hdmi-ip-sx00 e0250000.hdmi: owl_hdmic_enable
296[ 0.423874] open file /dev/nand0
297[ 0.423874] file is err
298[ 0.423906] open file /dev/block/nand0
299[ 0.423906] file is err
300[ 0.423906] open file /dev/md_d0
301[ 0.423937] file is err
302[ 0.423937] open file /dev/block/md_d0
303[ 0.423937] file is err
304[ 0.423937] open file /dev/mmcblk0
305[ 0.423937] file is err
306[ 0.423968] open file /dev/block/mmcblk0
307[ 0.423968] file is err
308[ 0.423968] no blk dev
309[ 0.423968] read MiscInfoHeader failed
310[ 0.423968] read Head failed
311[ 0.423999] ip_sx00_hdcp: hdcp_read_key, failed to read hdcp key from secure storage(-11)
312[ 0.431718] vce_drv: warning: cann't get vol regulator, may be this board not need, or lost in dts!
313[ 0.431812] #### insmod vde driver!
314[ 0.431968] mali0 e0280000.vde: Probe vde device
315[ 0.431968] info ic_type 0x900
316[ 0.431999] mali0 e0280000.vde: resource: iomem: [mem 0xe0280000-0xe0280107] mapping to ffffff8000bb0000, irq 82
317[ 0.432031] SPS_PG_CTL = 0xffffff8000bb2000
318[ 0.432031] CMU_COREPLL = 0xffffff8000bb4000
319[ 0.432062] CMU_VDE_CLK = 0xffffff8000bb6040
320[ 0.432062] CMU_DEVRST0 = 0xffffff8000bb80a8
321[ 0.432062] CMU_DEVCLKEN0 = 0xffffff8000bba0a0
322[ 0.432062] dev add ffffffc079e56010, vde_clk ffffffc079df7e80
323[ 0.432124] #### insmod hde driver!
324[ 0.432312] hde e0230000.hde: Probe hde device
325[ 0.432312] info ic_type 0x900
326[ 0.432312] hde e0230000.hde: resource: iomem: [mem 0xe0230000-0xe0230107] mapping to ffffff8000bbc000, irq 98
327[ 0.432343] SPS_PG_CTL = 0xffffff8000bbe000
328[ 0.432343] CMU_HDE_CLK = 0xffffff8000bc0000
329[ 0.432343] CMU_HDE_CLK = 0xffffff8000bc203c
330[ 0.432374] CMU_DEVRST0 = 0xffffff8000bc40a8
331[ 0.432374] CMU_DEVCLKEN0 = 0xffffff8000bc60a0
332[ 0.432374] dev add ffffffc079e56410, hde_clk ffffffc079dd4780
333[ 0.432437] owl_dmm_pm_init
334[ 0.432562] owl_chipid_init
335[ 0.432999] serial-owl e0126000.uart: detected port 3
336[ 0.433062] e0126000.uart: ttyS3 at MMIO 0xe0126000 (irq = 64) is a serial-owl
337[ 0.433218] serial-owl e012a000.uart: detected port 5
338[ 0.433281] e012a000.uart: ttyS5 at MMIO 0xe012a000 (irq = 66) is a serial-owl
339[ 1.794249] console [ttyS5] enabled
340[ 1.797937] [OWL] serial driver initialized
341[ 1.806687] brd: module loaded
342[ 1.812062] loop: module loaded
343[ 1.815249] misc_info_init, line 1096, May 27 2016 15:42:03
344[ 1.820906] mi_debug_init, line 353
345[ 1.824937] tun: Universal TUN/TAP device driver, 1.6
346[ 1.829999] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
347[ 1.836437] PPP generic driver version 2.4.2
348[ 1.840843] PPP BSD Compression module registered
349[ 1.845562] PPP Deflate Compression module registered
350[ 1.850656] PPP MPPE Compression module registered
351[ 1.855499] NET: Registered protocol family 24
352[ 1.860062] usbcore: registered new interface driver rtl8150
353[ 1.865781] usbcore: registered new interface driver r8152
354[ 1.871312] usbcore: registered new interface driver asix
355[ 1.876749] usbcore: registered new interface driver ax88179_178a
356[ 1.882906] usbcore: registered new interface driver cdc_ether
357[ 1.888781] usbcore: registered new interface driver net1080
358[ 1.894499] usbcore: registered new interface driver cdc_subset
359[ 1.900468] usbcore: registered new interface driver zaurus
360[ 1.906156] usbcore: registered new interface driver cdc_ncm
361[ 1.911843] usbcore: registered new interface driver sr9700_android
362[ 1.918187] usbcore: registered new interface driver CoreChips
363[ 1.924124] owl_usb2phy_probe 171:May 27 2016 13:47:29
364[ 1.929437] owl_usb3phy_probe 99:May 27 2016 13:47:30
365[ 1.935687] s900_usb3phy_init 0x5d:0x52
366[ 1.939531] s900_usb3phy_init 0x87:0x20
367[ 2.143374] s900_usb2phy_param_setup device mode
368[ 2.155374] usb_charge_detect_init 132 adfu_running=0
369[ 2.181374] dwc3_owl_probe 530 success
370[ 2.185656] mousedev: PS/2 mouse device common for all mice
371[ 2.191499] atc260x-adckeypad atc2609a-adckeypad.0: Probing...
372[ 2.197343] atc260x-adckeypad atc2609a-adckeypad.0: select AUXADC channel AUX0
373[ 2.204593] atc260x-adckeypad atc2609a-adckeypad.0: keymapsize = 2
374[ 2.210781] atc260x-adckeypad atc2609a-adckeypad.0: filter_dep = 3
375[ 2.216968] atc260x-adckeypad atc2609a-adckeypad.0: variance = 15
376[ 2.223062] atc260x-adckeypad atc2609a-adckeypad.0: poll_interval = 20ms
377[ 2.229906] input: atc2609a-adckeypad as /devices/e0176000.i2c/i2c-3/3-0065/atc2609a-adckeypad.0/input/input0
378[ 2.240312] atc260x-onoff atc2609a-onoff.0: Probing atc2609a-onoff
379[ 2.246499] atc260x-onoff atc2609a-onoff.0: atc260x_onoff IRQ num : 284
380[ 2.253218] input: atc260x_onoff as /devices/e0176000.i2c/i2c-3/3-0065/atc2609a-onoff.0/input/input1
381[ 2.263406] usbcore: registered new interface driver xpad
382[ 2.269343] atc260x-rtc atc2609a-rtc.0: Probing...
383[ 2.274312] atc260x-adckeypad atc2609a-adckeypad.0: key_code=103 val=0
384[ 2.284124] atc260x-rtc atc2609a-rtc.0: rtc core: registered atc260x-RTC as rtc0
385[ 2.291812] atc260x-rtc atc2609a-rtc.0: invalid year(0), reset to year 2015
386[ 2.299968] atc260x-rtc atc2609a-rtc.0: RTC alarm IRQ num : 285
387[ 2.307781] IR NEC protocol handler initialized
388[ 2.312343] IR RC5(x) protocol handler initialized
389[ 2.317187] IR RC6 protocol handler initialized
390[ 2.321749] IR JVC protocol handler initialized
391[ 2.326312] IR Sony protocol handler initialized
392[ 2.330937] IR RC5 (streamzap) protocol handler initialized
393[ 2.336562] IR SANYO protocol handler initialized
394[ 2.341312] IR MCE Keyboard/mouse protocol handler initialized
395[ 2.347249] atc260x_charger: version(r2p1), time stamp(20151111164507)
396[ 2.354187] create sysfs for atc260x charger
397[ 2.358499] [atc260x_charger_cfg_init] backlight_on_vol_diff not found, 350 default
398[ 2.366156] [atc260x_charger_cfg_init] backlight_off_vol_diff not found, 400 default
399[ 2.373937] [atc260x_charger_cfg_init] change_current_temp not found, 1 default
400[ 2.381249] [atc260x_charger_cfg_init] cur_rise_enable not found, 0 default
401[ 2.388218] [atc260x_charger_cfg_init] ot_shutoff_enable not found, 1 default
402[ 2.395374] [atc260x_charger_cfg_init] ext_buck_exist not found, 0 default
403[ 2.402312] atc260x_charger_cfg_init wall swicth gpio not exist!
404[ 2.414312] [atc260x_charger_wallv_buck_init] unable to request PWM for ext dcdc
405[ 2.422312] atc260x-hwmon atc2609a-hwmon.0: Probing atc2609a-hwmon
406[ 2.428562] open file /dev/nand0
407[ 2.431781] file is err
408[ 2.434312] open file /dev/block/nand0
409[ 2.434499] PDEVID = 0
410[ 2.434499] tmu-mem:start=0x3759341568
411[ 2.434593] tmu-mem:data->base=0xffffff8000bec000
412[ 2.434593] Begin to register thermal zone ,id = 0
413[ 2.434749] owl_get_crit_temp
414[ 2.456687] file is err
415[ 2.459187] open file /dev/md_d0
416[ 2.462437] file is err
417[ 2.464937] open file /dev/block/md_d0
418[ 2.468687] file is err
419[ 2.471187] open file /dev/mmcblk0
420[ 2.474624] file is err
421[ 2.477093] open file /dev/block/mmcblk0
422[ 2.481031] file is err
423[ 2.483499] no blk dev
424[ 2.485874] read MiscInfoHeader failed
425[ 2.489624] read Head failed
426[ 2.492499] ip_sx00_hdcp: hdcp_read_key, failed to read hdcp key from secure storage(-11)
427[ 2.643874] OWL: Kernel Thermal management registered
428[ 2.648937] PDEVID = 4
429[ 2.651312] tmu-mem:start=0x3759341584
430[ 2.655062] tmu-mem:data->base=0xffffff8000bee010
431[ 2.659781] Begin to register thermal zone ,id = 4
432[ 2.664687] owl_get_crit_temp
433[ 2.763843] OWL: Kernel Thermal management registered
434[ 2.768968] md: raid0 personality registered for level 0
435[ 2.774499] device-mapper: uevent: version 1.0.3
436[ 2.779312] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
437[ 2.787874] Bluetooth: HCI UART driver ver 2.2
438[ 2.792343] Bluetooth: HCI H4 protocol initialized
439[ 2.797249] cpuidle: using governor ladder
440[ 2.801343] cpuidle: using governor menu
441[ 2.805906] s900-mmc e0334000.mmc: using dma0chan0 for DMA transfers
442[ 2.812281] wifi card use 1.8v to scan
443[ 2.816812] get wifi ldo voltage:3300000-3310000
444[ 2.821437] Regulator wifi bt power init
445[ 2.865374] SDC0 use sdio uart conversion
446[ 2.869406] s900-mmc e0330000.mmc: using dma0chan1 for DMA transfers
447[ 2.875781] use GPIO to detect SD/MMC card
448[ 2.914124] hidraw: raw HID events driver (C) Jiri Kosina
449[ 2.924624] usbcore: registered new interface driver usbhid
450[ 2.930187] usbhid: USB HID core driver
451[ 2.936312] ashmem: initialized
452[ 2.941624] logger: created 256K log 'log_main'
453[ 2.946312] logger: created 256K log 'log_events'
454[ 2.951187] logger: created 256K log 'log_radio'
455[ 2.955937] logger: created 256K log 'log_system'
456[ 2.961437] s900_pcm_init
457[ 2.964218] s900-pcm-audio s900-pcm-audio: s900_pcm_probe!!
458[ 2.969843] atc2609a_audio_init audio!!!
459[ 2.974031] atc2609a_audio_platform_probe!
460[ 2.978124] add file!
461[ 2.980499] add file!
462[ 2.983062] it's ok 0
463[ 2.985406] owl-audio-i2s e0100000.owl-audio-i2s: s900_dai_probe
464[ 2.991656] s900-hdmi-audio s900-hdmi-audio: s900_hdmi_probe!!
465[ 2.997562] s900_link_init
466[ 3.000562] soc-audio soc-audio: ASoC: machine s900_link should use snd_soc_register_card()
467[ 3.013218] owl_mmc_get_ro: Card read-only status -38
468[ 3.018281] mmc1: host does not support reading read-only switch. assuming write-enable.
469[ 3.028406] sd card init ok
470[ 3.031218] mmc1: new high speed SDHC card at address 0007
471[ 3.036968] mmcblk0: mmc1:0007 SD8GB 7.42 GiB
472[ 3.048281] mmcblk0: p1 p2
473[ 3.165624] atc2609a-audio atc260x-audio: ASoC: no dapm match for AOUT FL FR Mixer --> AOUT MIXER --> ADC0 Mux
474[ 3.175624] atc2609a-audio atc260x-audio: ASoC: Failed to add route AOUT FL FR Mixer -> AOUT MIXER -> ADC0 Mux
475[ 3.188656] soc-audio soc-audio: atc2609a-dai <-> owl-audio-i2s mapping ok
476[ 3.196187] soc-audio soc-audio: s900-hdmi-dai <-> owl-audio-i2s mapping ok
477[ 3.204843] u32 classifier
478[ 3.207562] Actions configured
479[ 3.210999] Netfilter messages via NETLINK v0.30.
480[ 3.215812] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
481[ 3.222312] ctnetlink v0.93: registering with nfnetlink.
482[ 3.228031] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
483[ 3.234999] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
484[ 3.241499] xt_time: kernel timezone is -0000
485[ 3.246406] ip_tables: (C) 2000-2006 Netfilter Core Team
486[ 3.251937] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
487[ 3.258437] arp_tables: (C) 2002 David S. Miller
488[ 3.263156] TCP: cubic registered
489[ 3.266531] Initializing XFRM netlink socket
490[ 3.271281] NET: Registered protocol family 10
491[ 3.276437] mip6: Mobile IPv6
492[ 3.279437] ip6_tables: (C) 2000-2006 Netfilter Core Team
493[ 3.285156] sit: IPv6 over IPv4 tunneling driver
494[ 3.290499] NET: Registered protocol family 17
495[ 3.294968] NET: Registered protocol family 15
496[ 3.299437] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
497[ 3.305406] Bluetooth: HIDP socket layer initialized
498[ 3.310406] 8021q: 802.1Q VLAN Support v1.8
499[ 3.314624] lib80211: common routines for IEEE802.11 drivers
500[ 3.320593] Registering SWP/SWPB emulation handler
501[ 3.330749] Key type encrypted registered
502[ 3.338593] [OWL] pm init
503[ 3.341249] owl_pm_clear_flag: clear flag 0xffffffff
504[ 3.346312] ppm_owl_drv_init
505[ 3.349343] ppm_owl_base_init
506[ 3.352343] ppm_owl_fsm_init
507[ 3.355281] ppm_owl_sysfs_init
508[ 3.358343] ppm_owl_stats_init
509[ 3.361874] gpu-gpio-supply: disabling
510[ 3.365687] regulator-dummy: disabling
511[ 3.376468] atc260x-rtc atc2609a-rtc.0: setting system clock to 2015-01-01 00:00:16 UTC (1420070416)
512[ 3.385749] atc2609a_battery: atc2609a_bat_init fail to find atc2609a-battery node
513[ 3.393374] bq27441_battery_init fail to find bq27441-battery node
514[ 3.399687] table ffffffc000b76338, i 0, cpu_dev ffffffc000c4ba58, clk 1752000000, volt 1200000
515[ 3.408593] table ffffffc000b76338, i 1, cpu_dev ffffffc000c4ba58, clk 1608000000, volt 1125000
516[ 3.417499] table ffffffc000b76338, i 2, cpu_dev ffffffc000c4ba58, clk 1440000000, volt 1075000
517[ 3.426374] table ffffffc000b76338, i 3, cpu_dev ffffffc000c4ba58, clk 1104000000, volt 925000
518[ 3.435156] table ffffffc000b76338, i 4, cpu_dev ffffffc000c4ba58, clk 600000000, volt 850000
519[ 3.443874] table ffffffc000b76338, i 5, cpu_dev ffffffc000c4ba58, clk 240000000, volt 850000
520[ 3.452812] cpu0_cpufreq_driver_init: locking_frequency: 1104000
521[ 3.458906] [ppm_stat_notifier_policy,240]
522[ 3.466093] ALSA device list:
523[ 3.469062] #0: s900_link
524[ 3.472218] Freeing unused kernel memory: 372K (ffffffc000aac000 - ffffffc000b09000)
525Loading, please wait...
526starting version 229
527Begin: Loading essential drivers ... done.
528Begin: Running /scripts/init-premount ... done.
529Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done.
530Begin: Running /scripts/nfs-premount ... done.
531Begin: Running /scripts/local-top ... done.
532Begin: Running /scripts/local-premount ... ext4
533done.
534[ 4.036687] initrd: checking filesystem for writable partition
535[ 4.046593] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
536[ 4.056281] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
537[ 4.493968] open file /dev/nand0
538[ 4.497249] file is err
539[ 4.499749] open file /dev/block/nand0
540[ 4.503531] file is err
541[ 4.506093] open file /dev/md_d0
542[ 4.509374] file is err
543[ 4.511874] open file /dev/block/md_d0
544[ 4.515687] file is err
545[ 4.600249] read_mi_head, line 463, magic 0x0, length 0, item num 0
546[ 4.603187] EXT4-fs (mmcblk0p2): recovery complete
547[ 4.603249] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: errors=remount-ro
548[ 4.620593] read Head null
549[ 4.623406] ip_sx00_hdcp: hdcp_read_key, failed to read hdcp key from secure storage(-1)
550ext4
551[ 4.773843] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
552[ 4.784874] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
553[ 4.812937] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
554[ 4.893874] mmc1: Slot status change detected (0 -> 1)
555[ 4.986343] initrd: mounting /run
556mkdir: can't create directory '/root/writable/system-data//etc/hosts': File exists
557Begin: Running /scripts/local-bottom ... done.
558done.
559Begin: Running /scripts/nfs-bottom ... done.
560Begin: Running /scripts/init-bottom ... done.
561[ 6.199499] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +)
562[ 6.217781] systemd[1]: Detected architecture arm64.
563
564Welcome to Ubuntu 16.04 LTS!
565
566[ 6.254843] systemd[1]: Set hostname to <localhost.localdomain>.
567[ 6.260937] systemd[1]: Initializing machine ID from random generator.
568[ 6.267593] systemd[1]: Installed transient /etc/machine-id file.
569[ 6.565593] systemd[1]: writable.mount: Unit is bound to inactive unit dev-mmcblk0p2.device. Stopping, too.
570[ 6.594874] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
571[ OK ] Started Dispatch Password Requests to Console Directory Watch.
572[ 6.624187] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
573[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
574[ 6.653937] systemd[1]: Reached target Swap.
575[ OK ] Reached target Swap.
576[ 6.674187] systemd[1]: Listening on Journal Socket.
577[ OK ] Listening on Journal Socket.
578[ 6.694343] systemd[1]: Created slice User and Session Slice.
579[ OK ] Created slice User and Session Slice.
580[ 6.714093] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
581[ OK ] Started Forward Password Requests to Wall Directory Watch.
582[ 6.743968] systemd[1]: Listening on udev Control Socket.
583[ OK ] Listening on udev Control Socket.
584[ 6.764031] systemd[1]: Reached target Remote File Systems (Pre).
585[ OK ] Reached target Remote File Systems (Pre).
586[ 6.783906] systemd[1]: Reached target Remote File Systems.
587[ OK ] Reached target Remote File Systems.
588[ 6.803937] systemd[1]: Listening on udev Kernel Socket.
589[ OK ] Listening on udev Kernel Socket.
590[ 6.823906] systemd[1]: Reached target Encrypted Volumes.
591[ OK ] Reached target Encrypted Volumes.
592[ 6.843937] systemd[1]: Listening on Journal Socket (/dev/log).
593[ OK ] Listening on Journal Socket (/dev/log).
594[ 6.863968] systemd[1]: Listening on Syslog Socket.
595[ OK ] Listening on Syslog Socket.
596[ 6.883968] systemd[1]: Listening on fsck to fsckd communication Socket.
597[ OK ] Listening on fsck to fsckd communication Socket.
598[ 6.914437] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
599[ OK ] Set up automount Arbitrary Executab...ats File System Automount Point.
600[ 6.944093] systemd[1]: Created slice System Slice.
601[ OK ] Created slice System Slice.
602[ 6.968562] systemd[1]: Starting Load Kernel Modules...
603 Starting Load Kernel Modules...
604[ 6.995281] systemd[1]: Mounting POSIX Message Queue File System...
605 Mounting POSIX Message Queue File System...
606[ 7.025499] systemd[1]: Starting Remount Root and Kernel File Systems...
607 Starting Remount Root and Kernel File Systems...
608[ 7.055406] systemd[1]: Starting Journal Service...
609 Starting Journal Service...
610[ 7.074093] systemd[1]: Reached target Slices.
611[ OK ] Reached target Slices.
612[ 7.095531] systemd[1]: Starting Create Static Device Nodes in /dev...
613 Starting Create Static Device Nodes in /dev...
614[ 7.126562] systemd[1]: Mounting Debug File System...
615 Mounting Debug File System...
616[ 7.144437] systemd[1]: Created slice system-systemd\x2dfsck.slice.
617[ OK ] Created slice system-systemd\x2dfsck.slice.
618[ 7.175343] systemd[1]: Starting Nameserver information manager...
619 Starting Nameserver information manager...
620[ 7.205781] systemd[1]: Starting Set the hostname to the value stored on the writable partition...
621 Starting Set the hostname to the va...red on the writable partition...
622[ 7.234499] systemd[1]: Created slice system-serial\x2dgetty.slice.
623[ OK ] Created slice system-serial\x2dgetty.slice.
624[ 7.264437] systemd[1]: Created slice system-getty.slice.
625[ OK ] Created slice system-getty.slice.
626[ 7.300812] systemd[1]: Mounted Debug File System.
627[ OK ] Mounted Debug File System.
628[ 7.324093] systemd[1]: Mounted POSIX Message Queue File System.
629[ OK ] Mounted POSIX Message Queue File System.
630[ 7.344624] systemd[1]: Started Load Kernel Modules.
631[ OK ] Started Load Kernel Modules.
632[ 7.365031] systemd[1]: Started Remount Root and Kernel File Systems.
633[ OK ] Started Remount Root and Kernel File Systems.
634[ 7.394562] systemd[1]: Started Create Static Device Nodes in /dev.
635[ OK ] Started Create Static Device Nodes in /dev.
636[ 7.426843] systemd[1]: Started Set the hostname to the value stored on the writable partition.
637[ OK ] Started Set the hostname to the val...tored on the writable partition.
638[ 7.455374] systemd[1]: Started Nameserver information manager.
639[ OK ] Started Nameserver information manager.
640[ 7.485749] systemd[1]: Started Journal Service.
641[ OK ] Started Journal Service.
642 Starting udev Kernel Device Manager...
643 Starting udev Coldplug all Devices...
644[ OK ] Reached target Local File Systems (Pre).
645 Mounting /mnt...
646 Mounting /tmp...
647 Mounting /var/lib/sudo...
648 Mounting FUSE Control File System...
649 Mounting Configuration File System...
650 Starting Apply Kernel Variables...
651[ OK ] Mounted Configuration File System.
652[ OK ] Mounted FUSE Control File System.
653[ OK ] Mounted /tmp.
654[ OK ] Mounted /mnt.
655[ OK ] Mounted /var/lib/sudo.
656[ OK ] Started udev Kernel Device Manager.
657[ OK ] Started Apply Kernel Variables.
658[ OK ] Started udev Coldplug all Devices.
659[ OK ] Found device /dev/ttyS5.
660 Mounting /var/lib/logrotate...
661 Mounting /var/lib/extrausers...
662 Mounting /var/lib/waagent...
663 Mounting /root...
664 Mounting /var/log...
665 Mounting /var/lib/dbus...
666 Mounting /var/lib/dhcp...
667 Mounting /snap...
668 Mounting /var/lib/cloud...
669 Mounting /var/lib/systemd/rfkill...
670 Mounting /var/lib/apparmor...
671 Mounting /var/cache/apparmor...
672 Mounting /var/tmp...
673 Mounting /var/snap...
674 Mounting /var/lib/misc...
675 Mounting /var/lib/initramfs-tools...
676 Mounting /var/lib/snapd...
677 Mounting /home...
678 Mounting /var/lib/systemd/random-seed...
679[ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
680[ OK ] Reached target Sound Card.
681[ OK ] Mounted /home.
682[ OK ] Mounted /snap.
683[ OK ] Mounted /var/snap.
684[ OK ] Mounted /var/lib/cloud.
685[ OK ] Mounted /var/lib/dbus.
686[ OK ] Mounted /var/lib/dhcp.
687[ OK ] Mounted /var/lib/logrotate.
688[ OK ] Mounted /var/log.
689[ OK ] Mounted /var/cache/apparmor.
690[ OK ] Mounted /var/lib/apparmor.
691[ OK ] Mounted /var/tmp.
692[ OK ] Mounted /var/lib/initramfs-tools.
693[ OK ] Mounted /var/lib/misc.
694[ OK ] Mounted /var/lib/waagent.
695[ OK ] Mounted /root.
696[ OK ] Mounted /var/lib/extrausers.
697[ OK ] Mounted /var/lib/snapd.
698[ OK ] Mounted /var/lib/systemd/random-seed.
699[ OK ] Mounted /var/lib/systemd/rfkill.
700[ OK ] Found device /dev/mmcblk0p1.
701 Starting File System Check on /dev/mmcblk0p1...
702 Starting Load/Save Random Seed...
703 Starting Flush Journal to Persistent Storage...
704 Mounting Squashfs mount unit for bubblegum-kernel...
705 Mounting Squashfs mount unit for canonical-bugglegum...
706 Mounting Squashfs mount unit for ubuntu-core...
707[ OK ] Mounted Squashfs mount unit for canonical-bugglegum.
708[ OK ] Mounted Squashfs mount unit for bubblegum-kernel.
709[ OK ] Mounted Squashfs mount unit for ubuntu-core.
710[ OK ] Started Load/Save Random Seed.
711[ OK ] Started Flush Journal to Persistent Storage.
712[ OK ] Started File System Check Daemon to report status.
713[ OK ] Started File System Check on /dev/mmcblk0p1.
714 Mounting /boot/uboot...
715[ OK ] Mounted /boot/uboot.
716[ OK ] Reached target Local File Systems.
717 Starting LSB: AppArmor initialization...
718 Starting Initial cloud-init job (pre-networking)...
719 Starting Create Volatile Files and Directories...
720 Starting Run snappy firstboot setup...
721[ OK ] Started Create Volatile Files and Directories.
722 Starting Network Time Synchronization...
723 Starting Update UTMP about System Boot/Shutdown...
724[ OK ] Started Update UTMP about System Boot/Shutdown.
725[ OK ] Started Network Time Synchronization.
726[ OK ] Reached target System Time Synchronized.
727[FAILED] Failed to start LSB: AppArmor initialization.
728See 'systemctl status apparmor.service' for details.
729[ OK ] Reached target System Initialization.
730[ OK ] Started Daily Cleanup of Temporary Directories.
731[ OK ] Reached target Timers.
732[ OK ] Listening on D-Bus System Message Bus Socket.
733[ OK ] Started Trigger resolvconf update for networkd DNS.
734[ OK ] Reached target Paths.
735 Starting Socket activation for snappy daemon.
736[ OK ] Listening on Socket activation for snappy daemon.
737[ OK ] Reached target Sockets.
738[ OK ] Reached target Basic System.
739[ OK ] Started Cgroup management daemon.
740 Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"...
741 Starting Login Service...
742 Starting Restore /etc/resolv.conf i...re the ppp link was shut down...
743 Starting System Logging Service...
744[ OK ] Started Regular background program processing daemon.
745[ OK ] Started D-Bus System Message Bus.
746[ OK ] Started System Logging Service.
747[ OK ] Started Restore /etc/resolv.conf if...fore the ppp link was shut down.
748[ OK ] Started Login Service.
749[ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand".
750[ OK ] Started Run snappy firstboot setup.
751[ 22.902031] cloud-init[679]: Cloud-init v. 0.7.7 running 'init-local' at Fri, 27 May 2016 07:27:26 +0000. Up 19.06 .
752[ 22.931000] cloud-init[679]: Generating public/private rsa key pair.
753[ 22.951062] cloud-init[679]: Your identification has been saved in /etc/ssh/ssh_host_rsa_key.
754[ 22.971031] cloud-init[679]: Your public key has been saved in /etc/ssh/ssh_host_rsa_key.pub.
755[ 22.990968] cloud-init[679]: The key fingerprint is:
756[ 23.011031] cloud-init[679]: SHA256:r+WS6xT8eUcTWAWakvo/TfqtKauTTjnZzbGplW4lad8 root@localhost.localdomain
757[ 23.031031] cloud-init[679]: The key's randomart image is:
758[ 23.051031] cloud-init[679]: +---[RSA 2048]----+
759[ 23.071000] cloud-init[679]: | oo.|
760[ 23.091000] cloud-init[679]: | . = |
761[ 23.111000] cloud-init[679]: | o + . |
762[ 23.131031] cloud-init[679]: | . . . . |
763[ 23.151031] cloud-init[679]: | S +. |
764[ 23.170968] cloud-init[679]: | = = +=*.|
765[ OK ] Started Initial cloud-init job (pre-networking).
766[ 23.190375] cloud-init[679]: | ..@.o=O+.|
767[ OK ] Reached target Network (Pre).
768[ 23.230375] cloud-init[679]: | .o=o++=ooE|
769[ 23.270343] cloud-init[679]: | .+++o+*=..|
770[ 23.290187] cloud-init[679]: +----[SHA256]-----+
771[ 23.310156] cloud-init[679]: Generating public/private dsa key pair.
772[ 23.330156] cloud-init[679]: Your identification has been saved in /etc/ssh/ssh_host_dsa_key.
773[ 23.351062] cloud-init[679]: Your public key has been saved in /etc/ssh/ssh_host_dsa_key.pub.
774[ 23.371312] cloud-init[679]: The key fingerprint is:
775[ 23.391500] cloud-init[679]: SHA256:8mBvrQ6MNLSWTFoMZzuxmi9uG4SCre9fEJP/l63Qz4Q root@localhost.localdomain
776 Starting Raise network interfaces...
777[ 23.410437] cloud-init[679]: The key's randomart image is:
778[ 23.450375] cloud-init[679]: +---[DSA 1024]----+
779[ 23.470406] cloud-init[679]: | . + |
780[ 23.490375] cloud-init[679]: | = = |
781[ 23.510375] cloud-init[679]: | % |
782[ 23.530375] cloud-init[679]: |.o O B |
783[ 23.550343] cloud-init[679]: |+ * O = S |
784[ OK ] Started Raise network interfaces.
785[ 23.570375] cloud-init[679]: |.o + * * o + |
786[ 23.610281] cloud-init[679]: |. o o + * E o |
787[ 23.610562] cloud-init[679]: | o.o . o + = |
788[ 23.610718] cloud-init[679]: | o=o. .o . o |
789[ 23.610906] cloud-init[679]: +----[SHA256]-----+
790[ 23.611062] cloud-init[679]: Generating public/private ecdsa key pair.
791[ 23.611250] cloud-init[679]: Your identification has been saved in /etc/ssh/ssh_host_ecdsa_key.
792[ 23.611437] cloud-init[679]: Your public key has been saved in /etc/ssh/ssh_host_ecdsa_key.pub.
793[ 23.611593] cloud-init[679]: The key fingerprint is:
794[ 23.611750] cloud-init[679]: SHA256:0YUsiQRnEcNZT+OmF3kTZcOPqXVINQGy1vP6mWeEEX0 root@localhost.localdomain
795[ 23.611937] cloud-init[679]: The key's randomart image is:
796[ 23.612125] cloud-init[679]: +---[ECDSA 256]---+
797[ 23.612281] cloud-init[679]: | .+B*.oooo+==o|
798[ 23.612437] cloud-init[679]: | o+.o=o++o+.E|
799[ 23.612625] cloud-init[679]: | ..Boo+ *.|
800[ 23.612812] cloud-init[679]: | +.o .O o|
801[ 23.612968] cloud-init[679]: | S . o = |
802[ 23.613125] cloud-init[679]: | . . o .|
803[ 23.613312] cloud-init[679]: | . . |
804[ 23.613468] cloud-init[679]: | . =|
805[ 23.613656] cloud-init[679]: | =.|
806[ 23.613812] cloud-init[679]: +----[SHA256]-----+
807[ 23.614000] cloud-init[679]: Generating public/private ed25519 key pair.
808[ 23.614156] cloud-init[679]: Your identification has been saved in /etc/ssh/ssh_host_ed25519_key.
809[ 23.614343] cloud-init[679]: Your public key has been saved in /etc/ssh/ssh_host_ed25519_key.pub.
810[ 23.614500] cloud-init[679]: The key fingerprint is:
811[ 23.614687] cloud-init[679]: SHA256:okPc7bEMBypFyjsYOPHRVxFcpC7POPjPIb6n6puy0mo root@localhost.localdomain
812[ 23.614843] cloud-init[679]: The key's randomart image is:
813[ 23.615031] cloud-init[679]: +--[ED25519 256]--+
814[ 23.615187] cloud-init[679]: |. ... o+=o |
815[ 23.615375] cloud-init[679]: |.+ +. . .. |
816[ 23.616062] cloud-init[679]: |+ + ... . |
817[ 23.616218] cloud-init[679]: | + + o + |
818[ 23.616406] cloud-init[679]: |. + + = S |
819[ 23.616562] cloud-init[679]: | + o @ o |
820[ 23.616750] cloud-init[679]: | . + + B |
821[ 23.616906] cloud-init[679]: |.Eo = +.. |
822[ 23.617093] cloud-init[679]: |oo.+=o==o |
823[ 23.617250] cloud-init[679]: +----[SHA256]-----+
824[ OK ] Reached target Network.
825 Starting Initial cloud-init job (metadata service crawler)...
826[ 28.613406] cloud-init[806]: Cloud-init v. 0.7.7 running 'init' at Fri, 27 May 2016 07:27:35 +0000. Up 28.37 second.
827[ 28.640718] cloud-init[806]: 2016-05-27 07:27:35,603 - util.py[WARNING]: Route info failed: Unexpected error while .
828[ 28.660656] cloud-init[806]: Command: ['netstat', '-rn']
829[ 28.680406] cloud-init[806]: Exit code: 1
830[ 28.700406] cloud-init[806]: Reason: -
831[ 28.720843] cloud-init[806]: Stdout: 'Kernel IP routing table\nDestination Gateway Genmask Flag'
832[ 28.750750] cloud-init[806]: Stderr: ''
833[ 29.298625] cloud-init[806]: ci-info: +++++++++++++++++++++++++++++++++++++++++++Net device info++++++++++++++++++++
834[ 29.321062] cloud-init[806]: ci-info: +---------+-------+-----------+-----------+-------+--------------------------+
835[ 29.351031] cloud-init[806]: ci-info: | Device | Up | Address | Mask | Scope | Hw-Add|
836[ 29.381062] cloud-init[806]: ci-info: +---------+-------+-----------+-----------+-------+--------------------------+
837[ 29.411000] cloud-init[806]: ci-info: | lo | True | 127.0.0.1 | 255.0.0.0 | . | . |
838[ 29.441062] cloud-init[806]: ci-info: | lo | True | ::1/128 | . | host | . |
839[ 29.471000] cloud-init[806]: ci-info: | ip6tnl0 | False | . | . | . | 00-00-00-00-00-00-00-00-0|
840[ 29.501062] cloud-init[806]: ci-info: | sit0 | False | . | . | . | . |
841[ 29.531093] cloud-init[806]: ci-info: +---------+-------+-----------+-----------+-------+--------------------------+
842[ OK ] Started Initial cloud-init job (metadata service crawler).
843[ 29.560625] cloud-init[806]: ci-info: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Route info failed!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
844 Starting Permit User Sessions...
845[ OK ] Reached target Network is Online.
846 Starting Ubuntu FAN network setup...
847 Starting /etc/rc.local Compatibility...
848[ OK ] Reached target Cloud-config availability.
849 Starting Apply the settings specified in cloud-config...
850 Starting OpenBSD Secure Shell server...
851[ OK ] Started Permit User Sessions.
852[ OK ] Started Ubuntu FAN network setup.
853[ OK ] Started /etc/rc.local Compatibility.
854[ OK ] Started Serial Getty on ttyS5.
855[ OK ] Started Getty on tty1.
856[ OK ] Reached target Login Prompts.
857[ OK ] Started OpenBSD Secure Shell server.
858[ 35.301906] cloud-init[828]: Cloud-init v. 0.7.7 running 'modules:config' at Fri, 27 May 2016 07:27:41 +0000. Up 34.
859[ 35.302343] cloud-init[828]: 2016-05-27 07:27:42,291 - util.py[WARNING]: Running module snappy (<module 'cloudinit.d
860
861Ubuntu 16.04 LTS localhost.localdomain ttyS5
862
863localhost login: ubuntu
864Password:
865ci-info: +++++++++++++Authorized keys from /home/ubuntu/.ssh/authorized_keys for user ubuntu++++++++++++++
866ci-info: +---------+-------------------------------------------------+---------+-------------------------+
867ci-info: | Keytype | Fingerprint (md5) | Options | Comment |
868ci-info: +---------+-------------------------------------------------+---------+-------------------------+
869ci-info: | ssh-rsa | c8:ca:55:44:85:c4:b1:18:7f:09:4a:4d:aa:1d:9d:b2 | - | josh@josh-ThinkPad-T420 |
870ci-info: +---------+-------------------------------------------------+---------+-------------------------+
871<14>May 27 07:27:47 ec2:
872<14>May 27 07:27:47 ec2: #############################################################
873<14>May 27 07:27:47 ec2: -----BEGIN SSH HOST KEY FINGERPRINTS-----
874<14>May 27 07:27:47 ec2: 1024 SHA256:8mBvrQ6MNLSWTFoMZzuxmi9uG4SCre9fEJP/l63Qz4Q root@localhost.localdomain (DSA)
875<14>May 27 07:27:47 ec2: 256 SHA256:0YUsiQRnEcNZT+OmF3kTZcOPqXVINQGy1vP6mWeEEX0 root@localhost.localdomain (ECDSA)
876<14>May 27 07:27:47 ec2: 256 SHA256:okPc7bEMBypFyjsYOPHRVxFcpC7POPjPIb6n6puy0mo root@localhost.localdomain (ED25519)
877<14>May 27 07:27:47 ec2: 2048 SHA256:r+WS6xT8eUcTWAWakvo/TfqtKauTTjnZzbGplW4lad8 root@localhost.localdomain (RSA)
878<14>May 27 07:27:47 ec2: -----END SSH HOST KEY FINGERPRINTS-----
879<14>May 27 07:27:47 ec2: #############################################################
880-----BEGIN SSH HOST KEY KEYS-----
881ecdsa-sha2-nistp256 AAAAE2VjZHNhLXNoYTItbmlzdHAyNTYAAAAIbmlzdHAyNTYAAABBBBqaNJZX19+AApPK4E+u03nIHwzeGf7/P2HfM5evBqxFhbn
882ssh-ed25519 AAAAC3NzaC1lZDI1NTE5AAAAIE3KprD7AFjFiPtfUTzfRHm1wcV9w4Zq3690fuzzNOPb root@localhost.localdomain
883ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQDBUwi674Nbt8RkkiJ52vGYHnabptgfFxlfAehmFBVUOCJZ4enBdcxKv7aoQBFp3P2nxExxCtsLFpQrB4n
884-----END SSH HOST KEY KEYS-----
885[ 41.397187] cloud-init[853]: Cloud-init v. 0.7.7 running 'modules:final' at Fri, 27 May 2016 07:27:47 +0000. Up 40..
886[ 41.397625] cloud-init[853]: Cloud-init v. 0.7.7 finished at Fri, 27 May 2016 07:27:48 +0000. Datasource DataSources
887
888
889Login incorrect
890localhost.localdomain login:
891Password:
892
893
894
895
896Login incorrect
897localhost.localdomain login:
898Password:
899
900Login incorrect
901localhost.localdomain login: ubuntu
902Password:
903Welcome to Ubuntu 16.04 LTS (GNU/Linux 3.10.52 aarch64)
904
905 * Documentation: https://help.ubuntu.com/
906
907The programs included with the Ubuntu system are free software;
908the exact distribution terms for each program are described in the
909individual files in /usr/share/doc/*/copyright.
910
911Ubuntu comes with ABSOLUTELY NO WARRANTY, to the extent permitted by
912applicable law.
913
914Welcome to snappy Ubuntu Core, a transactionally updated Ubuntu.
915
916 * See https://ubuntu.com/snappy
917
918It's a brave new world here in snappy Ubuntu Core! This machine
919does not use apt-get or deb packages. Please see 'snappy --help'
920for app installation and transactional updates.
921
922To run a command as administrator (user "root"), use "sudo <command>".
923See "man sudo_root" for details.
924
925ubuntu@localhost:~$
926ubuntu@localhost:~$
927ubuntu@localhost:~$
928CTRL-A Z for help | 115200 8N1 | NOR | Minicom 2.7 | VT102 | Offline | ttyUSB0