· 6 years ago · Dec 04, 2019, 12:22 PM
1EFI stub: Booting Linux Kernel...
2EFI stub: EFI_RNG_PROTOCOL unavailable, no randomness supplied
3EFI stub: Using DTB from configuration table
4EFI stub: Exiting boot services and installing virtual address map...
5[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
6[ 0.000000] Linux version 5.4.0-dirty (jerome@matebook) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #263 SMP PREEMPT Wed Dec 4 13:11:26 CET 2019
7[ 0.000000] Machine model: HiKey960
8[ 0.000000] earlycon: pl11 at MMIO 0x00000000fff32000 (options '')
9[ 0.000000] printk: bootconsole [pl11] enabled
10[ 0.000000] printk: debug: ignoring loglevel setting.
11[ 0.000000] efi: Getting EFI parameters from FDT:
12[ 0.000000] efi: EFI v2.60 by EDK II
13[ 0.000000] efi: MEMATTR=0xbe7dc118 MEMRESERVE=0xba6e6018
14[ 0.000000] cma: Reserved 32 MiB at 0x00000000bc400000
15[ 0.000000] NUMA: No NUMA configuration found
16[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000bfffffff]
17[ 0.000000] NUMA: NODE_DATA [mem 0xbf9d6800-0xbf9d7fff]
18[ 0.000000] Zone ranges:
19[ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000bfffffff]
20[ 0.000000] Normal empty
21[ 0.000000] Movable zone start for each node
22[ 0.000000] Early memory node ranges
23[ 0.000000] node 0: [mem 0x0000000000000000-0x000000001abfffff]
24[ 0.000000] node 0: [mem 0x000000001ad88000-0x0000000031ffffff]
25[ 0.000000] node 0: [mem 0x0000000032101000-0x000000003dffffff]
26[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000089b7ffff]
27[ 0.000000] node 0: [mem 0x0000000089cc0000-0x00000000ba49ffff]
28[ 0.000000] node 0: [mem 0x00000000ba4a0000-0x00000000ba6dffff]
29[ 0.000000] node 0: [mem 0x00000000ba6e0000-0x00000000ba6e7fff]
30[ 0.000000] node 0: [mem 0x00000000ba6e8000-0x00000000ba6ebfff]
31[ 0.000000] node 0: [mem 0x00000000ba6ec000-0x00000000bf6affff]
32[ 0.000000] node 0: [mem 0x00000000bf6b0000-0x00000000bf6effff]
33[ 0.000000] node 0: [mem 0x00000000bf6f0000-0x00000000bf6fffff]
34[ 0.000000] node 0: [mem 0x00000000bf700000-0x00000000bf74ffff]
35[ 0.000000] node 0: [mem 0x00000000bf750000-0x00000000bfffffff]
36[ 0.000000] Zeroed struct page in unavailable ranges: 624 pages
37[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000bfffffff]
38[ 0.000000] On node 0 totalpages: 777271
39[ 0.000000] DMA32 zone: 12288 pages used for memmap
40[ 0.000000] DMA32 zone: 0 pages reserved
41[ 0.000000] DMA32 zone: 777271 pages, LIFO batch:63
42[ 0.000000] psci: probing for conduit method from DT.
43[ 0.000000] psci: PSCIv1.1 detected in firmware.
44[ 0.000000] psci: Using standard PSCI v0.2 function IDs
45[ 0.000000] psci: Trusted OS migration not required
46[ 0.000000] psci: SMC Calling Convention v1.1
47[ 0.000000] percpu: Embedded 31 pages/cpu s86488 r8192 d32296 u126976
48[ 0.000000] pcpu-alloc: s86488 r8192 d32296 u126976 alloc=31*4096
49[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
50[ 0.000000] Detected VIPT I-cache on CPU0
51[ 0.000000] CPU features: detected: ARM erratum 845719
52[ 0.000000] Speculative Store Bypass Disable mitigation not required
53[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 764983
54[ 0.000000] Policy zone: DMA32
55[ 0.000000] Kernel command line: BOOT_IMAGE=/Image console=tty0 console=ttyAMA6,115200n8 earlycon=pl011,0xfff32000 root=/dev/disk/by-partlabel/system rootwait rw ignore_loglevel efi=noruntime
56[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
57[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
58[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
59[ 0.000000] Memory: 2969900K/3109084K available (14972K kernel code, 2730K rwdata, 7476K rodata, 7936K init, 473K bss, 106416K reserved, 32768K cma-reserved)
60[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
61[ 0.000000] ftrace: allocating 52124 entries in 204 pages
62[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
63[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
64[ 0.000000] Tasks RCU enabled.
65[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
66[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
67[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
68[ 0.000000] GIC: Using split EOI/Deactivate mode
69[ 0.000000] random: get_random_bytes called from start_kernel+0x324/0x4b8 with crng_init=0
70[ 0.000000] arch_timer: cp15 timer(s) running at 1.92MHz (phys).
71[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1c570327e, max_idle_ns: 1763180809505 ns
72[ 0.000005] sched_clock: 56 bits at 1920kHz, resolution 520ns, wraps every 4398046510977ns
73[ 0.008506] clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58334160866034 ns
74[ 0.019128] Console: colour dummy device 80x25
75[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
76[ 0.000000] Linux version 5.4.0-dirty (jerome@matebook) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #263 SMP PREEMPT Wed Dec 4 13:11:26 CET 2019
77[ 0.000000] Machine model: HiKey960
78[ 0.000000] earlycon: pl11 at MMIO 0x00000000fff32000 (options '')
79[ 0.000000] printk: bootconsole [pl11] enabled
80[ 0.000000] printk: debug: ignoring loglevel setting.
81[ 0.000000] efi: Getting EFI parameters from FDT:
82[ 0.000000] efi: EFI v2.60 by EDK II
83[ 0.000000] efi: MEMATTR=0xbe7dc118 MEMRESERVE=0xba6e6018
84[ 0.000000] cma: Reserved 32 MiB at 0x00000000bc400000
85[ 0.000000] NUMA: No NUMA configuration found
86[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000bfffffff]
87[ 0.000000] NUMA: NODE_DATA [mem 0xbf9d6800-0xbf9d7fff]
88[ 0.000000] Zone ranges:
89[ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000bfffffff]
90[ 0.000000] Normal empty
91[ 0.000000] Movable zone start for each node
92[ 0.000000] Early memory node ranges
93[ 0.000000] node 0: [mem 0x0000000000000000-0x000000001abfffff]
94[ 0.000000] node 0: [mem 0x000000001ad88000-0x0000000031ffffff]
95[ 0.000000] node 0: [mem 0x0000000032101000-0x000000003dffffff]
96[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000089b7ffff]
97[ 0.000000] node 0: [mem 0x0000000089cc0000-0x00000000ba49ffff]
98[ 0.000000] node 0: [mem 0x00000000ba4a0000-0x00000000ba6dffff]
99[ 0.000000] node 0: [mem 0x00000000ba6e0000-0x00000000ba6e7fff]
100[ 0.000000] node 0: [mem 0x00000000ba6e8000-0x00000000ba6ebfff]
101[ 0.000000] node 0: [mem 0x00000000ba6ec000-0x00000000bf6affff]
102[ 0.000000] node 0: [mem 0x00000000bf6b0000-0x00000000bf6effff]
103[ 0.000000] node 0: [mem 0x00000000bf6f0000-0x00000000bf6fffff]
104[ 0.000000] node 0: [mem 0x00000000bf700000-0x00000000bf74ffff]
105[ 0.000000] node 0: [mem 0x00000000bf750000-0x00000000bfffffff]
106[ 0.000000] Zeroed struct page in unavailable ranges: 624 pages
107[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000bfffffff]
108[ 0.000000] On node 0 totalpages: 777271
109[ 0.000000] DMA32 zone: 12288 pages used for memmap
110[ 0.000000] DMA32 zone: 0 pages reserved
111[ 0.000000] DMA32 zone: 777271 pages, LIFO batch:63
112[ 0.000000] psci: probing for conduit method from DT.
113[ 0.000000] psci: PSCIv1.1 detected in firmware.
114[ 0.000000] psci: Using standard PSCI v0.2 function IDs
115[ 0.000000] psci: Trusted OS migration not required
116[ 0.000000] psci: SMC Calling Convention v1.1
117[ 0.000000] percpu: Embedded 31 pages/cpu s86488 r8192 d32296 u126976
118[ 0.000000] pcpu-alloc: s86488 r8192 d32296 u126976 alloc=31*4096
119[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
120[ 0.000000] Detected VIPT I-cache on CPU0
121[ 0.000000] CPU features: detected: ARM erratum 845719
122[ 0.000000] Speculative Store Bypass Disable mitigation not required
123[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 764983
124[ 0.000000] Policy zone: DMA32
125[ 0.000000] Kernel command line: BOOT_IMAGE=/Image console=tty0 console=ttyAMA6,115200n8 earlycon=pl011,0xfff32000 root=/dev/disk/by-partlabel/system rootwait rw ignore_loglevel efi=noruntime
126[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
127[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
128[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
129[ 0.000000] Memory: 2969900K/3109084K available (14972K kernel code, 2730K rwdata, 7476K rodata, 7936K init, 473K bss, 106416K reserved, 32768K cma-reserved)
130[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
131[ 0.000000] ftrace: allocating 52124 entries in 204 pages
132[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
133[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
134[ 0.000000] Tasks RCU enabled.
135[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
136[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
137[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
138[ 0.000000] GIC: Using split EOI/Deactivate mode
139[ 0.000000] random: get_random_bytes called from start_kernel+0x324/0x4b8 with crng_init=0
140[ 0.000000] arch_timer: cp15 timer(s) running at 1.92MHz (phys).
141[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1c570327e, max_idle_ns: 1763180809505 ns
142[ 0.000005] sched_clock: 56 bits at 1920kHz, resolution 520ns, wraps every 4398046510977ns
143[ 0.008506] clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58334160866034 ns
144[ 0.019128] Console: colour dummy device 80x25
145[ 0.462425] printk: console [tty0] enabled
146[ 0.466756] Calibrating delay loop (skipped), value calculated using timer frequency.. 3.84 BogoMIPS (lpj=7680)
147[ 0.477026] pid_max: default: 32768 minimum: 301
148[ 0.481805] LSM: Security Framework initializing
149[ 0.486574] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
150[ 0.494113] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
151[ 0.526182] ASID allocator initialised with 32768 entries
152[ 0.539716] rcu: Hierarchical SRCU implementation.
153[ 0.554518] EFI runtime services will be disabled.
154[ 0.567428] smp: Bringing up secondary CPUs ...
155[ 0.604492] Detected VIPT I-cache on CPU1
156[ 0.604593] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
157[ 0.636403] Detected VIPT I-cache on CPU2
158[ 0.636436] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
159[ 0.668416] Detected VIPT I-cache on CPU3
160[ 0.668441] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
161[ 0.701999] CPU features: detected: ARM erratum 858921
162[ 0.702041] Detected VIPT I-cache on CPU4
163[ 0.702059] arch_timer: Enabling local workaround for ARM erratum 858921
164[ 0.702069] arch_timer: CPU4: Trapping CNTVCT access
165[ 0.702076] CPU4: Booted secondary processor 0x0000000100 [0x410fd091]
166[ 0.732442] Detected VIPT I-cache on CPU5
167[ 0.732455] arch_timer: Enabling local workaround for ARM erratum 858921
168[ 0.732460] arch_timer: CPU5: Trapping CNTVCT access
169[ 0.732465] CPU5: Booted secondary processor 0x0000000101 [0x410fd091]
170[ 0.764488] Detected VIPT I-cache on CPU6
171[ 0.764501] arch_timer: Enabling local workaround for ARM erratum 858921
172[ 0.764506] arch_timer: CPU6: Trapping CNTVCT access
173[ 0.764511] CPU6: Booted secondary processor 0x0000000102 [0x410fd091]
174[ 0.796506] Detected VIPT I-cache on CPU7
175[ 0.796518] arch_timer: Enabling local workaround for ARM erratum 858921
176[ 0.796523] arch_timer: CPU7: Trapping CNTVCT access
177[ 0.796528] CPU7: Booted secondary processor 0x0000000103 [0x410fd091]
178[ 0.796584] smp: Brought up 1 node, 8 CPUs
179[ 0.927596] SMP: Total of 8 processors activated.
180[ 0.932353] CPU features: detected: 32-bit EL0 Support
181[ 0.937558] CPU features: detected: CRC32 instructions
182[ 0.951289] CPU: All CPU(s) started at EL2
183[ 0.955457] alternatives: patching kernel code
184[ 0.961095] devtmpfs: initialized
185[ 0.968082] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
186[ 0.977942] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
187[ 0.985581] pinctrl core: initialized pinctrl subsystem
188[ 0.991507] DMI not present or invalid.
189[ 0.995573] NET: Registered protocol family 16
190[ 1.008731] DMA: preallocated 256 KiB pool for atomic allocations
191[ 1.014896] audit: initializing netlink subsys (disabled)
192[ 1.020423] audit: type=2000 audit(0.752:1): state=initialized audit_enabled=0 res=1
193[ 1.028268] cpuidle: using governor menu
194[ 1.032434] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
195[ 1.039999] Serial: AMBA PL011 UART driver
196[ 1.059242] hi3660-mbox e896b000.mailbox: Mailbox enabled
197[ 1.075257] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
198[ 1.082038] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
199[ 1.088811] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
200[ 1.095584] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
201[ 1.103823] cryptd: max_cpu_qlen set to 1000
202[ 1.110440] ACPI: Interpreter disabled.
203[ 1.115035] iommu: Default domain type: Translated
204[ 1.120147] vgaarb: loaded
205[ 1.123044] SCSI subsystem initialized
206[ 1.126918] libata version 3.00 loaded.
207[ 1.130942] usbcore: registered new interface driver usbfs
208[ 1.136514] usbcore: registered new interface driver hub
209[ 1.141917] usbcore: registered new device driver usb
210[ 1.147317] pps_core: LinuxPPS API ver. 1 registered
211[ 1.152343] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
212[ 1.161583] PTP clock support registered
213[ 1.165595] EDAC MC: Ver: 3.0.0
214[ 1.169060] Registered efivars operations
215[ 1.173420] FPGA manager framework
216[ 1.176885] Advanced Linux Sound Architecture Driver Initialized.
217[ 1.183615] clocksource: Switched to clocksource arch_sys_counter
218[ 1.488545] VFS: Disk quotas dquot_6.6.0
219[ 1.492566] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
220[ 1.499635] pnp: PnP ACPI: disabled
221[ 1.506398] thermal_sys: Registered thermal governor 'step_wise'
222[ 1.506400] thermal_sys: Registered thermal governor 'power_allocator'
223[ 1.512725] NET: Registered protocol family 2
224[ 1.523948] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
225[ 1.532603] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
226[ 1.540719] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
227[ 1.548319] TCP: Hash tables configured (established 32768 bind 32768)
228[ 1.554971] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
229[ 1.561791] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
230[ 1.569115] NET: Registered protocol family 1
231[ 1.573745] RPC: Registered named UNIX socket transport module.
232[ 1.579733] RPC: Registered udp transport module.
233[ 1.584487] RPC: Registered tcp transport module.
234[ 1.589239] RPC: Registered tcp NFSv4.1 backchannel transport module.
235[ 1.596010] PCI: CLS 0 bytes, default 64
236[ 1.600075] Unpacking initramfs...
237[ 1.782767] Freeing initrd memory: 7164K
238[ 1.787561] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
239[ 1.796048] hw perfevents: enabled with armv8_cortex_a73 PMU driver, 7 counters available
240[ 1.804579] kvm [1]: IPA Size Limit: 40bits
241[ 1.809279] kvm [1]: vgic interrupt IRQ1
242[ 1.813382] kvm [1]: Hyp mode initialized successfully
243[ 1.842865] Initialise system trusted keyrings
244[ 1.847458] workingset: timestamp_bits=44 max_order=20 bucket_order=0
245[ 1.856891] squashfs: version 4.0 (2009/01/31) Phillip Lougher
246[ 1.863167] NFS: Registering the id_resolver key type
247[ 1.868303] Key type id_resolver registered
248[ 1.872532] Key type id_legacy registered
249[ 1.876588] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
250[ 1.883436] 9p: Installing v9fs 9p2000 file system support
251[ 1.897523] Key type asymmetric registered
252[ 1.901668] Asymmetric key parser 'x509' registered
253[ 1.906615] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
254[ 1.914095] io scheduler mq-deadline registered
255[ 1.918672] io scheduler kyber registered
256[ 1.925124] pinctrl-single e896c000.pinmux: 124 pins, size 496
257[ 1.931120] pinctrl-single ff37e000.pinmux: 6 pins, size 24
258[ 1.936828] pinctrl-single ff3b6000.pinmux: 12 pins, size 48
259[ 1.942627] pinctrl-single ff3fd000.pinmux: 6 pins, size 24
260[ 1.948347] pinctrl-single fff11000.pinmux: 42 pins, size 168
261[ 1.954318] pinctrl-single e896c800.pinmux: 128 pins, size 512
262[ 1.960280] pinctrl-single ff3b6800.pinmux: 6 pins, size 24
263[ 1.965988] pinctrl-single ff3fd800.pinmux: 6 pins, size 24
264[ 1.971685] pinctrl-single ff37e800.pinmux: 6 pins, size 24
265[ 1.977409] pinctrl-single fff11800.pinmux: 47 pins, size 188
266[ 1.984137] pl061_gpio e8a0b000.gpio: PL061 GPIO chip registered
267[ 1.990322] pl061_gpio e8a0c000.gpio: PL061 GPIO chip registered
268[ 1.996494] pl061_gpio e8a0d000.gpio: PL061 GPIO chip registered
269[ 2.002673] pl061_gpio e8a0e000.gpio: PL061 GPIO chip registered
270[ 2.008853] pl061_gpio e8a0f000.gpio: PL061 GPIO chip registered
271[ 2.015028] pl061_gpio e8a10000.gpio: PL061 GPIO chip registered
272[ 2.021220] pl061_gpio e8a11000.gpio: PL061 GPIO chip registered
273[ 2.027398] pl061_gpio e8a12000.gpio: PL061 GPIO chip registered
274[ 2.033570] pl061_gpio e8a13000.gpio: PL061 GPIO chip registered
275[ 2.039747] pl061_gpio e8a14000.gpio: PL061 GPIO chip registered
276[ 2.045919] pl061_gpio e8a15000.gpio: PL061 GPIO chip registered
277[ 2.052092] pl061_gpio e8a16000.gpio: PL061 GPIO chip registered
278[ 2.058266] pl061_gpio e8a17000.gpio: PL061 GPIO chip registered
279[ 2.064435] pl061_gpio e8a18000.gpio: PL061 GPIO chip registered
280[ 2.070611] pl061_gpio e8a19000.gpio: PL061 GPIO chip registered
281[ 2.076787] pl061_gpio e8a1a000.gpio: PL061 GPIO chip registered
282[ 2.082957] pl061_gpio e8a1b000.gpio: PL061 GPIO chip registered
283[ 2.089130] pl061_gpio e8a1c000.gpio: PL061 GPIO chip registered
284[ 2.095306] pl061_gpio ff3b4000.gpio: PL061 GPIO chip registered
285[ 2.101486] pl061_gpio ff3b5000.gpio: PL061 GPIO chip registered
286[ 2.107667] pl061_gpio e8a1f000.gpio: PL061 GPIO chip registered
287[ 2.113845] pl061_gpio e8a20000.gpio: PL061 GPIO chip registered
288[ 2.120023] pl061_gpio fff0b000.gpio: PL061 GPIO chip registered
289[ 2.126200] pl061_gpio fff0c000.gpio: PL061 GPIO chip registered
290[ 2.132377] pl061_gpio fff0d000.gpio: PL061 GPIO chip registered
291[ 2.138556] pl061_gpio fff0e000.gpio: PL061 GPIO chip registered
292[ 2.144732] pl061_gpio fff0f000.gpio: PL061 GPIO chip registered
293[ 2.150906] pl061_gpio fff10000.gpio: PL061 GPIO chip registered
294[ 2.157081] pl061_gpio fff1d000.gpio: PL061 GPIO chip registered
295[ 2.201986] kirin-pcie f4000000.pcie: host bridge /soc/pcie@f4000000 ranges:
296[ 2.209126] kirin-pcie f4000000.pcie: MEM 0xf6000000..0xf7ffffff -> 0x00000000
297[ 3.221015] kirin-pcie f4000000.pcie: Link Fail
298[ 3.225661] kirin-pcie f4000000.pcie: PCI host bridge to bus 0000:00
299[ 3.232089] pci_bus 0000:00: root bus resource [bus 00-01]
300[ 3.237636] pci_bus 0000:00: root bus resource [mem 0xf6000000-0xf7ffffff] (bus address [0x00000000-0x01ffffff])
301[ 3.247951] pci 0000:00:00.0: [19e5:3660] type 01 class 0x060400
302[ 3.254058] pci 0000:00:00.0: reg 0x10: [mem 0xf6000000-0xf6ffffff]
303[ 3.260510] pci 0000:00:00.0: supports D1 D2
304[ 3.264824] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
305[ 3.272506] pci_bus 0000:01: busn_res: can not insert [bus 01-ff] under [bus 00-01] (conflicts with (null) [bus 00-01])
306[ 3.284784] pci 0000:00:00.0: BAR 0: assigned [mem 0xf6000000-0xf6ffffff]
307[ 3.291655] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
308[ 3.297153] pcieport 0000:00:00.0: PME: Signaling with IRQ 66
309[ 3.303089] pcieport 0000:00:00.0: AER: enabled with IRQ 66
310[ 3.309251] EINJ: ACPI disabled.
311[ 3.314936] k3-dma fdf30000.dma: initialized
312[ 3.319289] k3-dma e804b000.dma-controller: dma-channel-mask doesn't exist, considering all as available.
313[ 3.329615] k3-dma e804b000.dma-controller: initialized
314[ 3.338479] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
315[ 3.345854] SuperH (H)SCI(F) driver initialized
316[ 3.350664] msm_serial: driver initialized
317[ 3.359923] loop: module loaded
318[ 3.364641] ufshcd-hisi ff3b0000.ufs: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled
319[ 3.375384] ufshcd-hisi ff3b0000.ufs: ufshcd_populate_vreg: Unable to find vcc-supply regulator, assuming enabled
320[ 3.385763] ufshcd-hisi ff3b0000.ufs: ufshcd_populate_vreg: Unable to find vccq-supply regulator, assuming enabled
321[ 3.396228] ufshcd-hisi ff3b0000.ufs: ufshcd_populate_vreg: Unable to find vccq2-supply regulator, assuming enabled
322[ 3.436229] scsi host0: ufshcd
323[ 3.442346] libphy: Fixed MDIO Bus: probed
324[ 3.446609] tun: Universal TUN/TAP device driver, 1.6
325[ 3.452080] thunder_xcv, ver 1.0
326[ 3.455353] thunder_bgx, ver 1.0
327[ 3.458633] nicpf, ver 1.0
328[ 3.461636] hclge is initializing
329[ 3.464987] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
330[ 3.472286] hns3: Copyright (c) 2017 Huawei Corporation.
331[ 3.477680] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
332[ 3.483574] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
333[ 3.489575] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k
334[ 3.496611] igb: Copyright (c) 2007-2014 Intel Corporation.
335[ 3.502261] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
336[ 3.510177] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
337[ 3.516301] sky2: driver version 1.30
338[ 3.520296] usbcore: registered new interface driver asix
339[ 3.525767] usbcore: registered new interface driver ax88179_178a
340[ 3.531939] usbcore: registered new interface driver cdc_ether
341[ 3.532154] ufshcd-hisi ff3b0000.ufs: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0
342[ 3.537847] usbcore: registered new interface driver dm9601
343[ 3.556050] usbcore: registered new interface driver net1080
344[ 3.561782] usbcore: registered new interface driver cdc_subset
345[ 3.567779] usbcore: registered new interface driver zaurus
346[ 3.573429] usbcore: registered new interface driver cdc_ncm
347[ 3.579214] VFIO - User Level meta-driver version: 0.3
348[ 3.585076] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
349[ 3.591685] ehci-pci: EHCI PCI platform driver
350[ 3.596191] ehci-platform: EHCI generic platform driver
351[ 3.601528] ehci-orion: EHCI orion driver
352[ 3.605622] ehci-exynos: EHCI EXYNOS driver
353[ 3.609886] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
354[ 3.616140] ohci-pci: OHCI PCI platform driver
355[ 3.620646] ohci-platform: OHCI generic platform driver
356[ 3.625973] ohci-exynos: OHCI EXYNOS driver
357[ 3.630407] usbcore: registered new interface driver usb-storage
358[ 3.637734] rtc-pl031 fff04000.rtc: registered as rtc0
359[ 3.643204] i2c /dev entries driver
360[ 3.648735] sp805-wdt e8a06000.watchdog: registration successful
361[ 3.652221] ufshcd-hisi ff3b0000.ufs: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
362[ 3.654907] sp805-wdt e8a07000.watchdog: registration successful
363[ 3.667962] ufshcd-hisi ff3b0000.ufs: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0
364[ 3.684483] sdhci: Secure Digital Host Controller Interface driver
365[ 3.686174] scsi 0:0:0:49488: Well-known LUN TOSHIBA THGBF7G8K4LBATRC 0100 PQ: 0 ANSI: 6
366[ 3.690730] sdhci: Copyright(c) Pierre Ossman
367[ 3.703126] scsi 0:0:0:49476: Well-known LUN TOSHIBA THGBF7G8K4LBATRC 0100 PQ: 0 ANSI: 6
368[ 3.703772] Synopsys Designware Multimedia Card Interface Driver
369[ 3.714893] scsi 0:0:0:49456: Well-known LUN TOSHIBA THGBF7G8K4LBATRC 0100 PQ: 0 ANSI: 6
370[ 3.718470] dwmmc_k3 ff37f000.dwmmc1: fifo-depth property not found, using value of FIFOTH register as default
371[ 3.730594] scsi 0:0:0:0: Direct-Access TOSHIBA THGBF7G8K4LBATRC 0100 PQ: 0 ANSI: 6
372[ 3.739461] dwmmc_k3 ff37f000.dwmmc1: IDMAC supports 64-bit address mode.
373[ 3.748671] sd 0:0:0:0: Power-on or device reset occurred
374[ 3.749766] scsi 0:0:0:1: Direct-Access TOSHIBA THGBF7G8K4LBATRC 0100 PQ: 0 ANSI: 6
375[ 3.751928] dwmmc_k3 ff37f000.dwmmc1: Using internal DMA controller.
376[ 3.751936] sd 0:0:0:1: Power-on or device reset occurred
377[ 3.752128] scsi 0:0:0:2: Direct-Access TOSHIBA THGBF7G8K4LBATRC 0100 PQ: 0 ANSI: 6
378[ 3.754481] scsi 0:0:0:3: Direct-Access TOSHIBA THGBF7G8K4LBATRC 0100 PQ: 0 ANSI: 6
379[ 3.754631] sd 0:0:0:1: [sdb] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
380[ 3.754864] sd 0:0:0:1: [sdb] Write Protect is off
381[ 3.754868] sd 0:0:0:1: [sdb] Mode Sense: 00 32 00 10
382[ 3.755538] sd 0:0:0:1: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
383[ 3.755783] sd 0:0:0:1: [sdb] Optimal transfer size 65536 bytes
384[ 3.756591] sd 0:0:0:2: Power-on or device reset occurred
385[ 3.757887] sd 0:0:0:3: Power-on or device reset occurred
386[ 3.761514] sd 0:0:0:0: [sda] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
387[ 3.762044] sd 0:0:0:0: [sda] Write Protect is off
388[ 3.762046] sd 0:0:0:0: [sda] Mode Sense: 00 32 00 10
389[ 3.763096] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
390[ 3.763650] sd 0:0:0:0: [sda] Optimal transfer size 65536 bytes
391[ 3.765546] dwmmc_k3 ff37f000.dwmmc1: Version ID is 270a
392[ 3.769641] random: fast init done
393[ 3.774643] sd 0:0:0:2: [sdc] 2048 4096-byte logical blocks: (8.39 MB/8.00 MiB)
394[ 3.775971] sd 0:0:0:1: [sdb] Attached SCSI disk
395[ 3.777432] dwmmc_k3 ff37f000.dwmmc1: DW MMC controller at irq 60,32 bit host data width,256 deep fifo
396[ 3.778155] sd 0:0:0:3: [sdd] 7805952 4096-byte logical blocks: (32.0 GB/29.8 GiB)
397[ 3.778509] sd 0:0:0:3: [sdd] Write Protect is off
398[ 3.778511] sd 0:0:0:3: [sdd] Mode Sense: 00 32 00 10
399[ 3.780053] sd 0:0:0:3: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
400[ 3.780408] sd 0:0:0:3: [sdd] Optimal transfer size 65536 bytes
401[ 3.785304] sd 0:0:0:0: [sda] Attached SCSI disk
402[ 3.785929] sd 0:0:0:2: [sdc] Write Protect is off
403[ 3.793865] dwmmc_k3 ff37f000.dwmmc1: Got CD GPIO
404[ 3.796755] Alternate GPT is invalid, using primary GPT.
405[ 3.796769] sdd: sdd1 sdd2 sdd3 sdd4 sdd5 sdd6 sdd7 sdd8 sdd9 sdd10 sdd11 sdd12
406[ 3.801157] sd 0:0:0:2: [sdc] Mode Sense: 00 32 00 10
407[ 3.801874] sd 0:0:0:3: [sdd] Attached SCSI disk
408[ 3.820879] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
409[ 3.827957] sd 0:0:0:2: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA
410[ 3.844857] dwmmc_k3 ff3ff000.dwmmc2: fifo-depth property not found, using value of FIFOTH register as default
411[ 3.850251] sd 0:0:0:2: [sdc] Optimal transfer size 65536 bytes
412[ 3.856055] dwmmc_k3 ff3ff000.dwmmc2: IDMAC supports 64-bit address mode.
413[ 4.008620] dwmmc_k3 ff3ff000.dwmmc2: Using internal DMA controller.
414[ 4.015042] dwmmc_k3 ff3ff000.dwmmc2: Version ID is 270a
415[ 4.020424] dwmmc_k3 ff3ff000.dwmmc2: DW MMC controller at irq 61,32 bit host data width,256 deep fifo
416[ 4.023612] sd 0:0:0:2: [sdc] Attached SCSI disk
417[ 4.030087] sdhci-pltfm: SDHCI platform and OF driver helper
418[ 4.043243] ledtrig-cpu: registered to indicate activity on CPUs
419[ 4.049689] usbcore: registered new interface driver usbhid
420[ 4.055318] usbhid: USB HID core driver
421[ 4.060068] optee: probing for conduit method from DT.
422[ 4.065267] optee: revision 3.7 (479c49dd)
423[ 4.065781] optee: dynamic shared memory is enabled
424[ 4.074948] optee: PTA_CMD_GET_DEVICES invoke function err: ffff0006
425[ 4.088797] drop_monitor: Initializing network drop monitor service
426[ 4.095204] NET: Registered protocol family 17
427[ 4.099757] 9pnet: Installing 9P2000 support
428[ 4.104093] Key type dns_resolver registered
429[ 4.108657] registered taskstats version 1
430[ 4.112798] Loading compiled-in X.509 certificates
431[ 4.121386] ffd74000.serial: ttyAMA3 at MMIO 0xffd74000 (irq = 21, base_baud = 0) is a PL011 rev2
432[ 4.130828] fdf01000.serial: ttyAMA4 at MMIO 0xfdf01000 (irq = 22, base_baud = 0) is a PL011 rev2
433[ 4.139845] serial serial0: tty port ttyAMA4 registered
434[ 4.145191] fff32000.serial: ttyAMA6 at MMIO 0xfff32000 (irq = 23, base_baud = 0) is a PL011 rev2
435[ 4.154170] printk: console [ttyAMA6] enabled
436[ 4.154170] printk: console [ttyAMA6] enabled
437[ 4.162924] printk: bootconsole [pl11] disabled
438[ 4.162924] printk: bootconsole [pl11] disabled
439[ 4.173310] ssp-pl022 ffd68000.spi: ARM PL022 driver, device ID: 0x00041022
440[ 4.180359] ssp-pl022 ffd68000.spi: mapped registers from 0x00000000ffd68000 to (____ptrval____)
441[ 4.189185] ssp-pl022 ffd68000.spi: setup for DMA on RX dma0chan0, TX dma0chan1
442[ 4.199800] ssp-pl022 ff3b3000.spi: ARM PL022 driver, device ID: 0x00041022
443[ 4.206829] ssp-pl022 ff3b3000.spi: mapped registers from 0x00000000ff3b3000 to (____ptrval____)
444[ 4.215650] ssp-pl022 ff3b3000.spi: setup for DMA on RX dma0chan2, TX dma0chan3
445[ 4.231876] dwmmc_k3 ff3ff000.dwmmc2: fifo-depth property not found, using value of FIFOTH register as default
446[ 4.243625] dwmmc_k3 ff3ff000.dwmmc2: IDMAC supports 64-bit address mode.
447[ 4.250420] dwmmc_k3 ff3ff000.dwmmc2: Using internal DMA controller.
448[ 4.256774] dwmmc_k3 ff3ff000.dwmmc2: Version ID is 270a
449[ 4.262101] dwmmc_k3 ff3ff000.dwmmc2: DW MMC controller at irq 61,32 bit host data width,128 deep fifo
450[ 4.271488] mmc_host mmc1: card is non-removable.
451[ 4.374058] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
452[ 4.399460] input: keys as /devices/platform/keys/input/input0
453[ 4.406875] rtc-pl031 fff04000.rtc: setting system clock to 1970-01-01T00:01:24 UTC (84)
454[ 4.410008] dwmmc_k3 ff3ff000.dwmmc2: card claims to support voltages below defined range
455[ 4.415170] cfg80211: Loading compiled-in X.509 certificates for regulatory database
456[ 4.436734] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
457[ 4.441176] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0)
458[ 4.444572] ALSA device list:
459[ 4.454678] mmc1: new SDIO card at address 0001
460[ 4.455965] No soundcards found.
461[ 4.461436] wl18xx_driver wl18xx.0.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2
462[ 4.474592] wl18xx_driver wl18xx.0.auto: Falling back to sysfs fallback for: ti-connectivity/wl18xx-conf.bin
463[ 4.484678] uart-pl011 fff32000.serial: no DMA platform data
464[ 4.494181] Freeing unused kernel memory: 7936K
465[ 4.504655] Run /init as init process
466[ 36.075877] wlan-en-regulator: disabling
467[ 64.748104] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -11
468[ 64.756977] wlcore: WARNING falling back to default config
469[ 64.882854] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
470[ 64.956875] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0)
471[ 65.062831] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
472[ 65.135832] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0)
473[ 65.376879] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
474[ 65.406395] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead.
475[ 65.415095] wlcore: WARNING This default nvs file can be removed from the file system
476[ 65.423535] wlcore: loaded
477[ 134.866887] hisi_thermal fff30000.tsensor: sensor <1> THERMAL ALARM: 65370 > 65000
478[ 136.995839] random: crng init done