· 6 years ago · Nov 19, 2019, 01:30 PM
1CL-SOM-iMX7 # reset
2resetting ...
3
4U-Boot SPL 2017.07-cl-som-imx7-1.5 (Jun 18 2018 - 13:02:48)
5Booting from SPI flash
6Trying to boot from SPI
7
8
9U-Boot 2017.07-cl-som-imx7-1.5 (Jun 18 2018 - 13:02:48 +0300)
10
11CPU: Freescale i.MX7D rev1.3 at 792 MHz
12Reset cause: POR
13I2C: ready
14DRAM: 1 GiB
15PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
16NAND: 0 MiB
17MMC: FSL_SDHC: 0, FSL_SDHC: 1
18SF: Detected w25q16cl with page size 256 Bytes, erase size 4 KiB, total 2 MiB
19Video: 800x480x24
20In: serial
21Out: serial
22Err: serial
23Board: CL-SOM-iMX7 in secure mode
24Base board EEPROM layout initialization failure
25TFP410 validation read failure.
26Net: Ethernet initialization failure: secondary interface
27Board Net Initialization Failed
28FEC0
29starting USB...
30USB0: Port not available.
31USB1: USB EHCI 1.00
32scanning bus 1 for devices... 2 USB Device(s) found
33 scanning usb for storage devices... 0 Storage Device(s) found
34 scanning usb for ethernet devices... 0 Ethernet Device(s) found
35Hit any key to stop autoboot: 0
36SD boot attempt ...
37switch to partitions #0, OK
38mmc0 is current device
39reading boot.scr
40** Unable to read file boot.scr **
41switch to partitions #0, OK
42mmc0 is current device
43reading zImage
445988832 bytes read in 281 ms (20.3 MiB/s)
45reading imx7d-sbc-imx7.dtb
4642073 bytes read in 20 ms (2 MiB/s)
47Booting from mmc ...
48## Flattened Device Tree blob at 83000000
49 Booting using the fdt blob at 0x83000000
50 Using Device Tree in place at 83000000, end 8300d458
51
52Starting kernel ...
53
54Booting Linux on physical CPU 0x0
55Linux version 4.9.11-cl-som-imx7-5.1 (vagrant@ubuntu-bionic) (gcc version 8.3.0 (Buildroot 2019.08) ) #1 SMP PREEMPT Tue Nov 19 03:28:17 UTC 2019
56CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
57CPU: div instructions available: patching division code
58CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
59OF: fdt:Machine model: CompuLab CL-SOM-iMX7 on SB-SOM
60Reserved memory: created CMA memory pool at 0xac000000, size 320 MiB
61OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
62Memory policy: Data cache writealloc
63percpu: Embedded 14 pages/cpu @ab71e000 s26188 r8192 d22964 u57344
64Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
65Kernel command line: console=ttymxc0,115200 vt.global_cursor_default=0 root=/dev/mmcblk0p2 rootwait rw
66PID hash table entries: 4096 (order: 2, 16384 bytes)
67Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
68Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
69Memory: 697844K/1048576K available (8192K kernel code, 364K rwdata, 2800K rodata, 1024K init, 459K bss, 23052K reserved, 327680K cma-reserved, 0K highmem)
70Virtual kernel memory layout:
71 vector : 0xffff0000 - 0xffff1000 ( 4 kB)
72 fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
73 vmalloc : 0xc0800000 - 0xff800000 (1008 MB)
74 lowmem : 0x80000000 - 0xc0000000 (1024 MB)
75 pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
76 modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
77 .text : 0x80008000 - 0x80900000 (9184 kB)
78 .init : 0x80c00000 - 0x80d00000 (1024 kB)
79 .data : 0x80d00000 - 0x80d5b120 ( 365 kB)
80 .bss : 0x80d5d000 - 0x80dcfc28 ( 460 kB)
81SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
82Preemptible hierarchical RCU implementation.
83 Build-time adjustment of leaf fanout to 32.
84 RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
85RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
86NR_IRQS:16 nr_irqs:16 16
87arm_arch_timer: Architected cp15 timer(s) running at 8.00MHz (phys).
88clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns
89sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns
90Switching to timer-based delay loop, resolution 125ns
91Ignoring duplicate/late registration of read_current_timer delay
92clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
93Console: colour dummy device 80x30
94Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=80000)
95pid_max: default: 32768 minimum: 301
96Security Framework initialized
97Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
98Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
99CPU: Testing write buffer coherency: ok
100CPU0: update cpu_capacity 1024
101CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
102Setting up static identity map for 0x80100000 - 0x80100070
103CPU1: update cpu_capacity 1024
104CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
105Brought up 2 CPUs
106SMP: Total of 2 processors activated (32.00 BogoMIPS).
107CPU: All CPU(s) started in SVC mode.
108devtmpfs: initialized
109OF: Duplicate name in lcdif@30730000, renamed to "display#1"
110VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
111clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
112pinctrl core: initialized pinctrl subsystem
113NET: Registered protocol family 16
114DMA: preallocated 256 KiB pool for atomic coherent allocations
115cpuidle: using governor menu
116DDR type is DDR3!
117hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
118hw-breakpoint: maximum watchpoint size is 8 bytes.
119imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
120imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver
121MU is ready for cross core communication!
122mxs-dma 33000000.dma-apbh: initialized
123vgaarb: loaded
124SCSI subsystem initialized
125usbcore: registered new interface driver usbfs
126usbcore: registered new interface driver hub
127usbcore: registered new device driver usb
12830800000.aips-bus:usbphynop1 supply vcc not found, using dummy regulator
12930800000.aips-bus:usbphynop2 supply vcc not found, using dummy regulator
1301-0020 supply vcc not found, using dummy regulator
131pca953x 1-0020: interrupt support not compiled in
132i2c i2c-1: IMX I2C adapter registered
133i2c i2c-1: can't use DMA, using PIO instead.
1343-0020 supply vcc not found, using dummy regulator
135pca953x 3-0020: interrupt support not compiled in
136i2c i2c-3: IMX I2C adapter registered
137i2c i2c-3: can't use DMA, using PIO instead.
138media: Linux media interface: v0.10
139Linux video capture interface: v2.00
140pps_core: LinuxPPS API ver. 1 registered
141pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
142PTP clock support registered
143imx rpmsg driver is registered.
144Advanced Linux Sound Architecture Driver Initialized.
145Bluetooth: Core ver 2.22
146NET: Registered protocol family 31
147Bluetooth: HCI device and connection manager initialized
148Bluetooth: HCI socket layer initialized
149Bluetooth: L2CAP socket layer initialized
150Bluetooth: SCO socket layer initialized
151clocksource: Switched to clocksource arch_sys_counter
152VFS: Disk quotas dquot_6.6.0
153VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
154NET: Registered protocol family 2
155TCP established hash table entries: 8192 (order: 3, 32768 bytes)
156TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
157TCP: Hash tables configured (established 8192 bind 8192)
158UDP hash table entries: 512 (order: 2, 16384 bytes)
159UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
160NET: Registered protocol family 1
161RPC: Registered named UNIX socket transport module.
162RPC: Registered udp transport module.
163RPC: Registered tcp transport module.
164RPC: Registered tcp NFSv4.1 backchannel transport module.
165Bus freq driver module loaded
166futex hash table entries: 512 (order: 3, 32768 bytes)
167workingset: timestamp_bits=30 max_order=18 bucket_order=0
168NFS: Registering the id_resolver key type
169Key type id_resolver registered
170Key type id_legacy registered
171jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
172fuse init (API version 7.26)
173io scheduler noop registered
174io scheduler deadline registered
175io scheduler cfq registered (default)
176OF: PCI: host bridge /soc/pcie@0x33800000 ranges:
177OF: PCI: No bus range found for /soc/pcie@0x33800000, using [bus 00-ff]
178OF: PCI: IO 0x4ff80000..0x4ff8ffff -> 0x00000000
179OF: PCI: MEM 0x40000000..0x4fefffff -> 0x40000000
180imx6q-pcie 33800000.pcie: phy link never came up
181imx6q-pcie 33800000.pcie: Link never came up
182imx6q-pcie 33800000.pcie: failed to initialize host
183imx6q-pcie: probe of 33800000.pcie failed with error -110
184backlight supply power not found, using dummy regulator
18530730000.lcdif supply lcd not found, using dummy regulator
186mxsfb 30730000.lcdif: failed to find mxc display driver
187Console: switching to colour frame buffer device 100x30
188mxsfb 30730000.lcdif: initialized
189sil164_simple 3-0039: Error -6 reading from subaddress 0x1
190sil164_simple 3-0039: Error -6 reading from subaddress 0x0
191sil164_simple 3-0039: Error -6 reading from subaddress 0x3
192sil164_simple 3-0039: Error -6 reading from subaddress 0x2
193sil164_simple 3-0039: Error -6 reading from subaddress 0x4
194sil164_simple 3-0039: Unknown device 0:0.0
195imx-sdma 30bd0000.sdma: no iram assigned, using external mem
196imx-sdma 30bd0000.sdma: loaded firmware 4.2
197pfuze100-regulator 1-0008: Full layer: 1, Metal layer: 1
198pfuze100-regulator 1-0008: FAB: 0, FIN: 0
199pfuze100-regulator 1-0008: pfuze3000 found.
20030860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 47, base_baud = 1500000) is a IMX
201console [ttymxc0] enabled
20230890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 48, base_baud = 1500000) is a IMX
20330880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 49, base_baud = 5000000) is a IMX
204imx sema4 driver is registered.
205[drm] Initialized
206[drm] Initialized vivante 1.0.0 20120216 on minor 0
207brd: module loaded
208loop: module loaded
209at24 1-0050: 1024 byte 24c08 EEPROM, writable, 16 bytes/write
210spi_imx 30820000.ecspi: dma setup error -19, use pio
211m25p80 spi0.1: m25p16-nonjedec (2048 Kbytes)
2123 ofpart partitions found on MTD device spi0.1
213Creating 3 MTD partitions on "spi0.1":
2140x000000000000-0x0000000c0000 : "uboot"
2150x0000000c0000-0x000000100000 : "uboot environment"
2160x000000100000-0x000000200000 : "splash"
217spi_imx 30820000.ecspi: probed
218spi_imx 30840000.ecspi: dma setup error -19, use pio
219spi_imx 30840000.ecspi: probed
220libphy: Fixed MDIO Bus: probed
221CAN device driver interface
22230be0000.ethernet supply phy not found, using dummy regulator
223pps pps0: new PPS source ptp0
224libphy: fec_enet_mii_bus: probed
225fec 30be0000.ethernet eth0: registered PHC device 0
22630bf0000.ethernet supply phy not found, using dummy regulator
227pps pps1: new PPS source ptp1
228fec 30bf0000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
229fec 30bf0000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: 9a:fe:a9:b9:ec:28
230fec 30bf0000.ethernet eth1: registered PHC device 1
231usbcore: registered new interface driver asix
232usbcore: registered new interface driver ax88179_178a
233usbcore: registered new interface driver smsc75xx
234usbcore: registered new interface driver smsc95xx
235usbcore: registered new interface driver MOSCHIP usb-ethernet driver
236ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
237ehci-pci: EHCI PCI platform driver
238ehci-mxc: Freescale On-Chip EHCI Host driver
239usbcore: registered new interface driver usb-storage
24030b10200.usbmisc supply vbus-wakeup not found, using dummy regulator
24130b30200.usbmisc supply vbus-wakeup not found, using dummy regulator
24230b20200.usbmisc supply vbus-wakeup not found, using dummy regulator
24330b20000.usb supply vbus not found, using dummy regulator
244ci_hdrc ci_hdrc.1: EHCI Host Controller
245ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
246ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
247hub 1-0:1.0: USB hub found
248hub 1-0:1.0: 1 port detected
249mousedev: PS/2 mouse device common for all mice
250input: 30370000.snvs:snvs-powerkey as /devices/soc0/soc/30000000.aips-bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0
251rtc-em3027 1-0056: rtc core: registered rtc-em3027 as rtc0
252i2c /dev entries driver
253IR NEC protocol handler initialized
254IR RC5(x/sz) protocol handler initialized
255IR RC6 protocol handler initialized
256IR JVC protocol handler initialized
257IR Sony protocol handler initialized
258IR SANYO protocol handler initialized
259IR Sharp protocol handler initialized
260IR MCE Keyboard/mouse protocol handler initialized
261IR XMP protocol handler initialized
262imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0)
263sdhci: Secure Digital Host Controller Interface driver
264sdhci: Copyright(c) Pierre Ossman
265sdhci-pltfm: SDHCI platform and OF driver helper
266sdhci-esdhc-imx 30b40000.usdhc: could not get ultra high speed state, work on normal mode
267sdhci-esdhc-imx 30b40000.usdhc: Got CD GPIO
268sdhci-esdhc-imx 30b40000.usdhc: Got WP GPIO
269mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA
270sdhci-esdhc-imx 30b60000.usdhc: could not get ultra high speed state, work on normal mode
271mmc0: new high speed SDHC card at address 0007
272mmcblk0: mmc0:0007 SD4GB 3.71 GiB (ro)
273 mmcblk0: p1 p2
274mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA
275usbcore: registered new interface driver usbhid
276usbhid: USB HID core driver
2771-001a supply AVDD not found, using dummy regulator
2781-001a supply HPVDD not found, using dummy regulator
2791-001a supply DCVDD not found, using dummy regulator
2801-001a supply DBVDD not found, using dummy regulator
281wm8731 1-001a: Failed to issue reset: -6
282NET: Registered protocol family 10
283sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
284NET: Registered protocol family 17
285can: controller area network core (rev 20120528 abi 9)
286NET: Registered protocol family 29
287Key type dns_resolver registered
288cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19)
289Registering SWP/SWPB emulation handler
290usb 1-1: new high-speed USB device number 2 using ci_hdrc
291random: fast init done
292mmc2: new DDR MMC card at address 0001
293mmcblk2: mmc2:0001 M52516 14.3 GiB
294mmcblk2boot0: mmc2:0001 M52516 partition 1 4.00 MiB
295mmcblk2boot1: mmc2:0001 M52516 partition 2 4.00 MiB
296mmcblk2rpmb: mmc2:0001 M52516 partition 3 4.00 MiB
297 mmcblk2: p1 p2
298ci_hdrc ci_hdrc.2: EHCI Host Controller
299ci_hdrc ci_hdrc.2: new USB bus registered, assigned bus number 2
300ci_hdrc ci_hdrc.2: USB 2.0 started, EHCI 1.00
301hub 2-0:1.0: USB hub found
302hub 2-0:1.0: 1 port detected
303imx_thermal 30000000.aips-bus:tempmon: Extended Commercial CPU temperature grade - max:105C critical:100C passive:95C
304hub 1-1:1.0: USB hub found
305hub 1-1:1.0: 4 ports detected
306mmc1: SDHCI controller on 30b50000.usdhc [30b50000.usdhc] using ADMA
307rtc-em3027 1-0056: setting system clock to 2019-11-19 13:22:08 UTC (1574169728)
308sdhci-esdhc-imx 30b50000.usdhc: card claims to support voltages below defined range
309usb_otg1_vbus: disabling
310bt_en_fixed: disabling
311ALSA device list:
312 No soundcards found.
313VFS: Cannot open root device "mmcblk0p2" or unknown-block(179,2): error -30
314Please append a correct "root=" boot option; here are the available partitions:
3150100 65536 ram0 (driver?)
3160101 65536 ram1 (driver?)
3170102 65536 ram2 (driver?)
3180103 65536 ram3 (driver?)
3190104 65536 ram4 (driver?)
3200105 65536 ram5 (driver?)
3210106 65536 ram6 (driver?)
3220107 65536 ram7 (driver?)
3230108 65536 ram8 (driver?)
3240109 65536 ram9 (driver?)
325010a 65536 ram10 (driver?)
326010b 65536 ram11 (driver?)
327010c 65536 ram12 (driver?)
328010d 65536 ram13 (driver?)
329010e 65536 ram14 (driver?)
330010f 65536 ram15 (driver?)
3311f00 768 mtdblock0 (driver?)
3321f01 256 mtdblock1 (driver?)
3331f02 1024 mtdblock2 (driver?)
334b300 3887104 mmcblk0 driver: mmcblk
335 b301 16384 mmcblk0p1 00000000-01
336 b302 61440 mmcblk0p2 00000000-02
337b330 14942208 mmcblk2 driver: mmcblk
338 b331 102399 mmcblk2p1 00000000-01
339 b332 14839808 mmcblk2p2 00000000-02
340b360 4096 mmcblk2rpmb (driver?)
341b350 4096 mmcblk2boot1 (driver?)
342b340 4096 mmcblk2boot0 (driver?)
343Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,2)
344CPU0: stopping
345CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.11-cl-som-imx7-5.1 #1
346Hardware name: Freescale i.MX7 Dual (Device Tree)
347[<8010f574>] (unwind_backtrace) from [<8010b240>] (show_stack+0x10/0x14)
348[<8010b240>] (show_stack) from [<803b77ec>] (dump_stack+0x80/0x9c)
349[<803b77ec>] (dump_stack) from [<8010e2c0>] (handle_IPI+0x164/0x1b0)
350[<8010e2c0>] (handle_IPI) from [<8010147c>] (gic_handle_irq+0x8c/0xa0)
351[<8010147c>] (gic_handle_irq) from [<8010bc6c>] (__irq_svc+0x6c/0xa8)
352Exception stack(0x80d01f28 to 0x80d01f70)
3531f20: 00000000 ab726780 00000001 80d00000 ab722e00 80d0a280
3541f40: ab722e00 00000001 a095c513 a102875c 00000000 00000000 00000000 80d01f78
3551f60: 808adfdc 8065236c 20000113 ffffffff
356[<8010bc6c>] (__irq_svc) from [<8065236c>] (cpuidle_enter_state+0x130/0x2b4)
357[<8065236c>] (cpuidle_enter_state) from [<8016b9a8>] (cpu_startup_entry+0x158/0x208)
358[<8016b9a8>] (cpu_startup_entry) from [<80c00be4>] (start_kernel+0x314/0x384)
359[<80c00be4>] (start_kernel) from [<8000807c>] (0x8000807c)
360---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,2)
361usb 2-1: new high-speed USB device number 2 using ci_hdrc