· 6 years ago · Sep 05, 2019, 07:34 PM
1G12A:BL:583440:b596c7;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0;
2
3bl2_stage_init1
4
5L0:00000000
6L1:80000703
7L2:00008067
8L3:04000000
9B2:00002000
10B1:e0f83180
11
12TE: 147191
13
14BL2 Built : 21:12:49, Apr 28 2018. g12a g3a251ca - jenkins@walle02-sh
15
16Board ID = 1
17Set cpu clk to 24M
18Set clk81 to 24M
19CPU clk: 1200 MHz
20Set clk81 to 166.6M
21Handler is not supported
22boot_device: 1
23-s
24board id: 1
25Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x004000, part: 0
26fw parse done
27Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x004000, part: 0
28Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x004000, part: 0
29PIEI prepare done
30Cfg max: 4, cur: 1. Board id: 255. Force loop cfg
31DDR4 probe
32Set ddr clk to 912MHz
33Load ddrfw from eMMC, src: 0x00014200, des: 0xfffd0000, size: 0x00c000, part: 0
34dfi pinmux init
35ac pinmux init
36Check phy result
37INFO : End of initialization
38INFO : End of read enable training
39INFO : End of fine write leveling
40INFO : End of read dq deskew training
41INFO : End of MPR read delay center optimization
42INFO : End of Write leveling coarse delay
43INFO : End of write delay center optimization
44INFO : End of read delay center optimization
45INFO : End of max read latency training
46INFO : Training has run successfully!
471D training succeed
48Load ddrfw from eMMC, src: 0x00020200, des: 0xfffd0000, size: 0x00c000, part: 0
49Check phy result
50INFO : End of initialization
51INFO : End of 2D read delay Voltage center optimization
52INFO : End of 2D write delay Voltage center optimization
53INFO : Training has run successfully!
54
55R0_RxClkDly_Margin==205
56R0_TxDqDly_Margi==239
57R1_RxClkDly_Margin==0
58R1_TxDqDly_Margi==0
59
60PIEI init
61PIEI init cnt: 180
62 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0001
632D training succeed
64DDR size: 2048MB
65DataBus test pass!
66AddrBus test pass!
67result report
68Enable ddr reg access
6900000000
70 emmc switch 3 ok
71Authentication key not yet programmed
72emmc_rpmb_key_is_programmed: error 0x00000007
7300000000
74 emmc switch 0 ok
75Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x004000, part: 0
76Load BL3X from eMMC, src: 0x00064200, des: 0x01754000, size: 0x0b4000, part: 0
770.0;M3 CHK:0;cm4_sp_mode 0
78[Image: g12a_v1.1.3310-81c9e20 2018-05-02 10:15:01 jenkins@walle02-sh]
79OPS=0x10
8028 0a 10 00 6c 5f 6c 59 2d 41 32 31 47 4c 4d 41
81
82This is ES chip
83bl30:This chip has not trimmed thermal!!!
84bl30: thermal cali data update error
85[0.020913 Inits done]
86secure task start!
87high task start!
88low task start!
89run into bl31
90NOTICE: BL31: v1.3(release):debc425
91NOTICE: BL31: Built : 14:06:49, May 3 2018
92NOTICE: BL31: G12A normal boot!
93NOTICE: BL31: BL33 decompress pass
94ERROR: Error initializing runtime service opteed_fast
95
96U-Boot 2015.01-g784ee4d (May 04 2018 - 20:08:53)
97
98DRAM: 2 GiB
99Relocation Offset is: 76e83000
100spi_post_bind(spifc): req_seq = 0
101register usb cfg[0][1] = 0000000077f48578
102NAND: get_sys_clk_rate_mtd() 266, clock setting 200!
103NAND device id: 0 7 ff ff ff ff
104No NAND device found!!!
105nand init failed: -6
106get_sys_clk_rate_mtd() 266, clock setting 200!
107NAND device id: 0 7 ff ff ff ff
108No NAND device found!!!
109nand init failed: -6
110MMC: aml_priv->desc_buf = 0x0000000073e73710
111aml_priv->desc_buf = 0x0000000073e75a30
112SDIO Port B: 0, SDIO Port C: 1
113co-phase 0x2, tx-dly 0
114co-phase 0x2, tx-dly 0
115co-phase 0x2, tx-dly 0
116emmc/sd response timeout, cmd8, status=0x1ff2800
117emmc/sd response timeout, cmd55, status=0x1ff2800
118co-phase 0x2, tx-dly 0
119co-phase 0x2, tx-dly 0
120init_part() 297: PART_TYPE_AML
121[mmc_init] mmc init success
122start dts,buffer=0000000073e78280,dt_addr=0000000073e78280
123get_partition_from_dts() 105: ret 0
124parts: 14
12500: logo 0000000000800000 1
12601: recovery 0000000001800000 1
12702: misc 0000000000800000 1
12803: dto 0000000000800000 1
12904: cri_data 0000000000800000 2
13005: param 0000000001000000 2
13106: boot 0000000001000000 1
13207: rsv 0000000001000000 1
13308: tee 0000000002000000 1
13409: vendor 0000000010000000 1
13510: odm 0000000010000000 1
13611: system 0000000074000000 1
13712: cache 0000000046000000 2
13813: data ffffffffffffffff 4
139init_part() 297: PART_TYPE_AML
140eMMC/TSD partition table have been checked OK!
141check pattern success
142mmc env offset: 0x4d400000
143In: serial
144Out: serial
145Err: serial
146reboot_mode=cold_boot
147[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
148_verify_dtb_checksum()-2755: calc c2806ee9, store c2806ee9
149_verify_dtb_checksum()-2755: calc c2806ee9, store c2806ee9
150dtb_read()-2972: total valid 2
151update_old_dtb()-2953: do nothing
152amlkey_init() enter!
153[EFUSE_MSG]keynum is 4
154vpu: clk_level in dts: 7
155vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
156vpu: vpu_clk_gate_init_off finish
157vpp: vpp_init
158vpp: g12a osd1 matrix rgb2yuv ..............
159vpp: g12a osd2 matrix rgb2yuv..............
160vpp: g12a osd3 matrix rgb2yuv..............
161aml_config_dtb 572
162aml_config_dtb 574
163co_phase = <0x00000002>
164libfdt fdt_getprop(): FDT_ERR_NOTFOUND
165f_max = <0x02625a00>
166status = "okay"
167status = "okay"
168drive-strength = <0x00000001>
169drive-strength = <0x00000001>
170drive-strength = <0x00000001>
171drive-strength = <0x00000001>
172drive-strength = <0x00000002>
173drive-strength = <0x00000001>
174Net: dwmac.ff3f0000amlkey_init() enter!
175amlkey_init() 71: already init!
176[EFUSE_MSG]keynum is 4
177MACADDR:02:2d:59:6c:5f:6c(from chipid)
178
179Start read misc partition datas!
180info->attemp_times = 0
181info->active_slot = 0
182info->slot_info[0].bootable = 1
183info->slot_info[0].online = 1
184info->slot_info[1].bootable = 0
185info->slot_info[1].online = 0
186info->attemp_times = 0
187attemp_times = 0
188active slot = 0
189wipe_data=successful
190wipe_cache=successful
191upgrade_step=0
192[OSD]load fb addr from dts:/meson-fb
193[OSD]set initrd_high: 0x7f800000
194[OSD]fb_addr for logo: 0x7f800000
195[OSD]load fb addr from dts:/meson-fb
196[OSD]fb_addr for logo: 0x7f800000
197[OSD]VPP_OFIFO_SIZE:0xfff01fff
198[CANVAS]canvas init
199[CANVAS]addr=0x7f800000 width=3840, height=2160
200[OSD]osd_hw.free_dst_data: 0,1919,0,1079
201[OSD]osd1_update_disp_freescale_enable
202[1080p60hz] is invalid for cvbs.
203set hdmitx VIC = 16
204config HPLL = 4455000
205HPLL: 0x3b0004b9
206HPLL: 0x1b0004b9
207HPLL: 0xdb0004b9
208config HPLL done
209j = 6 vid_clk_div = 1
210hdmitx phy setting done
211hdmitx: set enc for VIC: 16
212enc_vpu_bridge_reset[1195]
213rx version is 1.4 or below div=10
214amlkey_init() enter!
215amlkey_init() 71: already init!
216[EFUSE_MSG]keynum is 4
217[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
218[KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
219[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
220Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
221g12a_u200_v1#
222g12a_u200_v1#version
223
224U-Boot 2015.01-g784ee4d (May 04 2018 - 20:08:53)
225aarch64-none-elf-gcc (crosstool-NG linaro-1.13.1-4.8-2013.11 - Linaro GCC 2013.10) 4.8.3 20131111 (prerelease)
226GNU ld (crosstool-NG linaro-1.13.1-4.8-2013.11 - Linaro GCC 2013.10) 2.23.2.20130610 Linaro 2013.10-4
227g12a_u200_v1#setenv preboot
228g12a_u200_v1#setenv fdt_high 0xffffffff
229g12a_u200_v1#setenv netargs 'setenv gatewayip ${gatewayip}; setenv bootargs ${bootargs} "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:::none"'
230g12a_u200_v1#setenv bootargs console=ttyAML0,115200 debug loglevel=8
231g12a_u200_v1#if test -n ${initenv}; then run initenv; fi
232g12a_u200_v1#if test -n ${preboot}; then run preboot; fi
233g12a_u200_v1#setenv autoload no
234g12a_u200_v1#setenv autoboot no
235g12a_u200_v1#dhcp
236dwmac.ff3f0000 Waiting for PHY auto negotiation to complete. done
237Speed: 100, full duplex
238BOOTP broadcast 1
239BOOTP broadcast 2
240DHCP client bound to address 192.168.0.200 (274 ms)
241g12a_u200_v1#setenv serverip 192.168.1.2
242g12a_u200_v1#if test -n ${netargs}; then run netargs; fi
243g12a_u200_v1#tftp 0x03000000 192.168.1.2:tmp/meson-g12a-u200-scLKlD/uImage-jyk1D0
244Speed: 100, full duplex
245Using dwmac.ff3f0000 device
246TFTP from server 192.168.1.2; our IP address is 192.168.0.200; sending through gateway 192.168.0.254
247Filename 'tmp/meson-g12a-u200-scLKlD/uImage-jyk1D0'.
248Load address: 0x3000000
249Loading: #################################################################
250 #################################################################
251 #################################################################
252 #################################################################
253 #################################################################
254 #################################################################
255 #################################################################
256 #################################################################
257 #################################################################
258 #################################################################
259 #################################################################
260 #################################################################
261 #################################################################
262 #################################################################
263 #################################################################
264 #################################################################
265 #################################################################
266 #################################################################
267 #################################################################
268 #################################################################
269 #################################################################
270 #################################################################
271 #################################################################
272 #################################################################
273 #################################################################
274 #################################################################
275 ############
276 686.5 KiB/s
277done
278Bytes transferred = 24975936 (17d1a40 hex)
279g12a_u200_v1#tftp 0x05300000 192.168.1.2:tmp/meson-g12a-u200-scLKlD/rootfs.cpio.gzwXeTRl.uboot
280Speed: 100, full duplex
281Using dwmac.ff3f0000 device
282TFTP from server 192.168.1.2; our IP address is 192.168.0.200; sending through gateway 192.168.0.254
283Filename 'tmp/meson-g12a-u200-scLKlD/rootfs.cpio.gzwXeTRl.uboot'.
284Load address: 0x5300000
285Loading: #################################################################
286 #################################################################
287 #################################################################
288 #################################################################
289 #######################
290 706.1 KiB/s
291done
292Bytes transferred = 4145080 (3f3fb8 hex)
293g12a_u200_v1#tftp 0x02f00000 192.168.1.2:tmp/meson-g12a-u200-scLKlD/tmpsBKWrD.dtb
294Speed: 100, full duplex
295Using dwmac.ff3f0000 device
296TFTP from server 192.168.1.2; our IP address is 192.168.0.200; sending through gateway 192.168.0.254
297Filename 'tmp/meson-g12a-u200-scLKlD/tmpsBKWrD.dtb'.
298Load address: 0x2f00000
299Loading: ###
300 650.4 KiB/s
301done
302Bytes transferred = 40671 (9edf hex)
303g12a_u200_v1#printenv bootargs
304bootargs=console=ttyAML0,115200 debug loglevel=8 ip=192.168.0.200:192.168.1.2:192.168.0.254:255.255.255.0:::none
305g12a_u200_v1#bootm 0x03000000 0x05300000 0x02f00000
306ee_gate_off ...
307## Booting kernel from Legacy Image at 03000000 ...
308 Image Name: Linux
309 Image Type: AArch64 Linux Kernel Image (uncompressed)
310 Data Size: 24975872 Bytes = 23.8 MiB
311 Load Address: 01080000
312 Entry Point: 01080000
313 Verifying Checksum ... OK
314## Loading init Ramdisk from Legacy Image at 05300000 ...
315 Image Name: rootfs.cpio.gz
316 Image Type: AArch64 Linux RAMDisk Image (uncompressed)
317 Data Size: 4145016 Bytes = 4 MiB
318 Load Address: 00000000
319 Entry Point: 00000000
320 Verifying Checksum ... OK
321load dtb from 0x1000000 ......
322## Flattened Device Tree blob at 02f00000
323 Booting using the fdt blob at 0x2f00000
324 Loading Kernel Image(COMP_NONE) ... OK
325 kernel loaded at 0x01080000, end = 0x02851a00
326libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
327[rsvmem] fdt get prop fail.
328 Loading Ramdisk to 73a7d000, end 73e70f78 ... OK
329 Loading Device Tree to 0000000073a70000, end 0000000073a7cede ... OK
330
331Starting kernel ...
332
333uboot time: 46216133 us
334[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
335[ 0.000000] Linux version 5.3.0-rc6-00113-gc339dc1d5d20-dirty (KernelCI@paris) (gcc version 6.3.0 20170516 (Debian 6.3.0-18)) #101 SMP PREEMPT Wed Aug 28
33608:43:46 PDT 2019
337[ 0.000000] Machine model: Amlogic Meson G12A U200 Development Board
338[ 0.000000] efi: Getting EFI parameters from FDT:
339[ 0.000000] efi: UEFI not found.
340[ 0.000000] Reserved memory: created CMA memory pool at 0x0000000063800000, size 256 MiB
341[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
342[ 0.000000] NUMA: No NUMA configuration found
343[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x0000000077ffffff]
344[ 0.000000] NUMA: NODE_DATA [mem 0x77bfb840-0x77bfcfff]
345[ 0.000000] Zone ranges:
346[ 0.000000] DMA32 [mem 0x0000000000000000-0x0000000077ffffff]
347[ 0.000000] Normal empty
348[ 0.000000] Movable zone start for each node
349[ 0.000000] Early memory node ranges
350[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000004ffffff]
351[ 0.000000] node 0: [mem 0x0000000005300000-0x0000000077ffffff]
352[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000077ffffff]
353[ 0.000000] On node 0 totalpages: 490752
354[ 0.000000] DMA32 zone: 7680 pages used for memmap
355[ 0.000000] DMA32 zone: 0 pages reserved
356[ 0.000000] DMA32 zone: 490752 pages, LIFO batch:63
357[ 0.000000] psci: probing for conduit method from DT.
358[ 0.000000] psci: PSCIv1.0 detected in firmware.
359[ 0.000000] psci: Using standard PSCI v0.2 function IDs
360[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
361[ 0.000000] psci: SMC Calling Convention v1.0
362[ 0.000000] percpu: Embedded 23 pages/cpu s56728 r8192 d29288 u94208
363[ 0.000000] pcpu-alloc: s56728 r8192 d29288 u94208 alloc=23*4096
364[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
365[ 0.000000] Detected VIPT I-cache on CPU0
366[ 0.000000] CPU features: detected: ARM erratum 845719
367[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 483072
368[ 0.000000] Policy zone: DMA32
369[ 0.000000] Kernel command line: console=ttyAML0,115200 debug loglevel=8 ip=192.168.0.200:192.168.1.2:192.168.0.254:255.255.255.0:::none
370[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
371[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
372[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
373[ 0.000000] Memory: 1631552K/1963008K available (11516K kernel code, 1798K rwdata, 6048K rodata, 4992K init, 448K bss, 69312K reserved, 262144K
374cma-reserved)
375[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
376[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
377[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
378[ 0.000000] Tasks RCU enabled.
379[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
380[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
381[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
382[ 0.000000] GIC: Using split EOI/Deactivate mode
383[ 0.000000] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
384[ 0.000000] random: get_random_bytes called from start_kernel+0x300/0x4a0 with crng_init=0
385[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
386[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
387[ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
388[ 0.000194] Console: colour dummy device 80x25
389[ 0.000279] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
390[ 0.000290] pid_max: default: 32768 minimum: 301
391[ 0.000363] LSM: Security Framework initializing
392[ 0.000421] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
393[ 0.000437] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
394[ 0.023982] ASID allocator initialised with 32768 entries
395[ 0.031971] rcu: Hierarchical SRCU implementation.
396[ 0.042787] EFI services will not be available.
397[ 0.048003] smp: Bringing up secondary CPUs ...
398[ 0.080216] Detected VIPT I-cache on CPU1
399[ 0.080272] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
400[ 0.112236] Detected VIPT I-cache on CPU2
401[ 0.112268] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
402[ 0.144280] Detected VIPT I-cache on CPU3
403[ 0.144302] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
404[ 0.144359] smp: Brought up 1 node, 4 CPUs
405[ 0.144376] SMP: Total of 4 processors activated.
406[ 0.144382] CPU features: detected: 32-bit EL0 Support
407[ 0.144387] CPU features: detected: CRC32 instructions
408[ 0.144867] CPU: All CPU(s) started at EL2
409[ 0.144887] alternatives: patching kernel code
410[ 0.145983] devtmpfs: initialized
411[ 0.153367] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
412[ 0.153388] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
413[ 0.159914] pinctrl core: initialized pinctrl subsystem
414[ 0.161379] DMI not present or invalid.
415[ 0.161720] NET: Registered protocol family 16
416[ 0.162066] audit: initializing netlink subsys (disabled)
417[ 0.162246] audit: type=2000 audit(0.160:1): state=initialized audit_enabled=0 res=1
418[ 0.163590] cpuidle: using governor menu
419[ 0.163862] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
420[ 0.165065] DMA: preallocated 256 KiB pool for atomic allocations
421[ 0.166613] Serial: AMBA PL011 UART driver
422[ 0.183565] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
423[ 0.183578] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
424[ 0.183583] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
425[ 0.183589] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
426[ 0.185237] cryptd: max_cpu_qlen set to 1000
427[ 0.188377] ACPI: Interpreter disabled.
428[ 0.190157] VDDAO_3V3: supplied by 12V
429[ 0.190878] vgaarb: loaded
430[ 0.191185] SCSI subsystem initialized
431[ 0.191314] libata version 3.00 loaded.
432[ 0.191529] usbcore: registered new interface driver usbfs
433[ 0.191565] usbcore: registered new interface driver hub
434[ 0.191614] usbcore: registered new device driver usb
435[ 0.192240] pps_core: LinuxPPS API ver. 1 registered
436[ 0.192245] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
437[ 0.192258] PTP clock support registered
438[ 0.192394] EDAC MC: Ver: 3.0.0
439[ 0.193555] FPGA manager framework
440[ 0.193633] Advanced Linux Sound Architecture Driver Initialized.
441[ 0.194235] clocksource: Switched to clocksource arch_sys_counter
442[ 0.194397] VFS: Disk quotas dquot_6.6.0
443[ 0.194448] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
444[ 0.194615] pnp: PnP ACPI: disabled
445[ 0.199234] thermal_sys: Registered thermal governor 'step_wise'
446[ 0.199238] thermal_sys: Registered thermal governor 'power_allocator'
447[ 0.199705] NET: Registered protocol family 2
448[ 0.200033] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
449[ 0.200064] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
450[ 0.200172] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
451[ 0.200377] TCP: Hash tables configured (established 16384 bind 16384)
452[ 0.200472] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
453[ 0.200514] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
454[ 0.200647] NET: Registered protocol family 1
455[ 0.201049] RPC: Registered named UNIX socket transport module.
456[ 0.201054] RPC: Registered udp transport module.
457[ 0.201059] RPC: Registered tcp transport module.
458[ 0.201062] RPC: Registered tcp NFSv4.1 backchannel transport module.
459[ 0.201073] PCI: CLS 0 bytes, default 64
460[ 0.201229] Unpacking initramfs...
461[ 0.386817] Freeing initrd memory: 4044K
462[ 0.387444] kvm [1]: IPA Size Limit: 40bits
463[ 0.388105] kvm [1]: vgic interrupt IRQ1
464[ 0.388204] kvm [1]: Hyp mode initialized successfully
465[ 0.443845] Initialise system trusted keyrings
466[ 0.444044] workingset: timestamp_bits=44 max_order=19 bucket_order=0
467[ 0.449685] squashfs: version 4.0 (2009/01/31) Phillip Lougher
468[ 0.450351] NFS: Registering the id_resolver key type
469[ 0.450375] Key type id_resolver registered
470[ 0.450380] Key type id_legacy registered
471[ 0.450391] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
472[ 0.450540] 9p: Installing v9fs 9p2000 file system support
473[ 0.465524] Key type asymmetric registered
474[ 0.465539] Asymmetric key parser 'x509' registered
475[ 0.465608] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
476[ 0.465615] io scheduler mq-deadline registered
477[ 0.465620] io scheduler kyber registered
478[ 0.476908] EINJ: ACPI disabled.
479[ 0.485957] soc soc0: Amlogic Meson G12A (S905D2) Revision 28:a (10:2) Detected
480[ 0.488488] pwm-regulator: supplied by regulator-dummy
481[ 0.488687] VCC_3V3: supplied by VDDAO_3V3
482[ 0.488725] FLASH_1V8: supplied by VCC_3V3
483[ 0.488786] VCC_1V8: supplied by VCC_3V3
484[ 0.488828] VDDAO_1V8: supplied by VDDAO_3V3
485[ 0.492230] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
486[ 0.494364] SuperH (H)SCI(F) driver initialized
487[ 0.494952] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 11, base_baud = 1500000) is a meson_uart
488[ 1.333197] printk: console [ttyAML0] enabled
489[ 1.337917] msm_serial: driver initialized
490[ 1.348502] loop: module loaded
491[ 1.352716] libphy: Fixed MDIO Bus: probed
492[ 1.352971] tun: Universal TUN/TAP device driver, 1.6
493[ 1.356987] thunder_xcv, ver 1.0
494[ 1.359417] thunder_bgx, ver 1.0
495[ 1.362595] nicpf, ver 1.0
496[ 1.365788] hclge is initializing
497[ 1.368543] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
498[ 1.375683] hns3: Copyright (c) 2017 Huawei Corporation.
499[ 1.380988] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
500[ 1.386719] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
501[ 1.392615] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k
502[ 1.399483] igb: Copyright (c) 2007-2014 Intel Corporation.
503[ 1.405033] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
504[ 1.412766] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
505[ 1.418942] sky2: driver version 1.30
506[ 1.422878] VFIO - User Level meta-driver version: 0.3
507[ 1.429056] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
508[ 1.433827] ehci-pci: EHCI PCI platform driver
509[ 1.438248] ehci-platform: EHCI generic platform driver
510[ 1.443503] ehci-orion: EHCI orion driver
511[ 1.447444] ehci-exynos: EHCI EXYNOS driver
512[ 1.451568] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
513[ 1.457634] ohci-pci: OHCI PCI platform driver
514[ 1.462040] ohci-platform: OHCI generic platform driver
515[ 1.467289] ohci-exynos: OHCI EXYNOS driver
516[ 1.471780] usbcore: registered new interface driver usb-storage
517[ 1.479582] meson-vrtc ff8000a8.rtc: registered as rtc0
518[ 1.483023] i2c /dev entries driver
519[ 1.491001] amlogic_thermal ff634800.temperature-sensor: Failed to register tsensor: -19
520[ 1.494212] amlogic_thermal ff634c00.temperature-sensor: Failed to register tsensor: -19
521[ 1.506461] sdhci: Secure Digital Host Controller Interface driver
522[ 1.508064] sdhci: Copyright(c) Pierre Ossman
523[ 1.512670] Synopsys Designware Multimedia Card Interface Driver
524[ 1.519135] meson-gx-mmc ffe05000.sd: Got CD GPIO
525[ 1.549584] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq
526[ 1.576260] sdhci-pltfm: SDHCI platform and OF driver helper
527[ 1.577391] ledtrig-cpu: registered to indicate activity on CPUs
528[ 1.582607] meson-sm: secure-monitor enabled
529[ 1.587119] usbcore: registered new interface driver usbhid
530[ 1.592017] usbhid: USB HID core driver
531[ 1.599097] NET: Registered protocol family 17
532[ 1.600371] 9pnet: Installing 9P2000 support
533[ 1.604530] Key type dns_resolver registered
534[ 1.609134] registered taskstats version 1
535[ 1.612750] Loading compiled-in X.509 certificates
536[ 1.626619] VCC_5V: supplied by 12V
537[ 1.628900] USB_PWR_EN: supplied by VCC_5V
538[ 1.629019] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2
539[ 1.633818] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1
540[ 1.642651] dwc2 ff400000.usb: ff400000.usb supply vusb_d not found, using dummy regulator
541[ 1.647138] dwc2 ff400000.usb: ff400000.usb supply vusb_a not found, using dummy regulator
542[ 1.655508] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
543[ 1.663613] dwc3 ff500000.usb: Failed to get clk 'ref': -2
544[ 1.668107] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
545[ 1.673144] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
546[ 1.680942] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000000000010010
547[ 1.690077] xhci-hcd xhci-hcd.0.auto: irq 24, io mem 0xff500000
548[ 1.696414] hub 1-0:1.0: USB hub found
549[ 1.699627] hub 1-0:1.0: 2 ports detected
550[ 1.703840] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
551[ 1.709078] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
552[ 1.716680] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
553[ 1.723101] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
554[ 1.731399] hub 2-0:1.0: USB hub found
555[ 1.734881] hub 2-0:1.0: 1 port detected
556[ 1.738876] dwc3-meson-g12a ffe09000.usb: switching to Device Mode
557[ 1.745330] meson-vrtc ff8000a8.rtc: setting system clock to 1970-01-01T00:00:01 UTC (1)
558[ 1.771311] mmc1: tuning execution failed: -5
559[ 1.771332] mmc1: error -5 whilst initialising MMC card
560[ 14.050420] USB_PWR_EN: disabling
561[ 14.050435] ALSA device list:
562[ 14.051033] No soundcards found.
563[ 14.061668] Freeing unused kernel memory: 4992K
564[ 14.061747] Run /init as init process
565Starting logging: OK
566Populating /dev using udev: [ 14.100041] udevd[186]: starting version 3.2.5
567[ 14.100335] random: udevd: uninitialized urandom read (16 bytes read)
568[ 14.105412] random: udevd: uninitialized urandom read (16 bytes read)
569[ 14.111646] random: udevd: uninitialized urandom read (16 bytes read)
570[ 14.121731] udevd[187]: starting eudev-3.2.5
571done
572Initializing random number generator... done.
573Starting network: OK
574Starting dropbear sshd: OK
575/bin/sh: can't access tty; job control turned off
576/ # cat /proc/cmdline
577console=ttyAML0,115200 debug loglevel=8 ip=192.168.0.200:192.168.1.2:192.168.0.254:255.255.255.0:::none
578/ # uname -r
5795.3.0-rc6-00113-gc339dc1d5d20-dirty
580/ # cat /proc/cpuinfo
581processor : 0
582BogoMIPS : 48.00
583Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
584CPU implementer : 0x41
585CPU architecture: 8
586CPU variant : 0x0
587CPU part : 0xd03
588CPU revision : 4
589
590processor : 1
591BogoMIPS : 48.00
592Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
593CPU implementer : 0x41
594CPU architecture: 8
595CPU variant : 0x0
596CPU part : 0xd03
597CPU revision : 4
598
599processor : 2
600BogoMIPS : 48.00
601Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
602CPU implementer : 0x41
603CPU architecture: 8
604CPU variant : 0x0
605CPU part : 0xd03
606CPU revision : 4
607
608processor : 3
609BogoMIPS : 48.00
610Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
611CPU implementer : 0x41
612CPU architecture: 8
613CPU variant : 0x0
614CPU part : 0xd03
615CPU revision : 4
616
617/ # (user:khilman) disconnected
618
619/ # cd /sys/devices/system/cpu/cpufreq/policy0/
620/sys/devices/system/cpu/cpufreq/policy0 # cat scaling_governor
621performance
622/sys/devices/system/cpu/cpufreq/policy0 # cat scaling_cur_freq
6231800000
624/sys/devices/system/cpu/cpufreq/policy0 # cat scaling_available_
625cat: can't open 'scaling_available_': No such file or directory
626/sys/devices/system/cpu/cpufreq/policy0 # cat scaling_available_frequencies
627100000 250000 500000 666666 1000000 1200000 1398000 1512000 1608000 1704000 1800000
628/sys/devices/system/cpu/cpufreq/policy0 # echo userspace > scaling_governor
629/sys/devices/system/cpu/cpufreq/policy0 # echo 6666[ 299.224513] random: fast init done
630/sys/devices/system/cpu/cpufreq/policy0 # echo 666666 > scaling_setspeed
631/sys/devices/system/cpu/cpufreq/policy0 # cat scaling_cur_freq
632666666
633/sys/devices/system/cpu/cpufreq/policy0 # rtcwake -d rtc0 -m mem -s4
634wakeup from "mem" at Thu Jan 1 00:05:19 1970
635[ 314.506870] PM: suspend entry (deep)
636[ 314.506942] Filesystems sync: 0.000 seconds
637[ 314.509949] Freezing user space processes ... (elapsed 0.001 seconds) done.
638[ 314.515896] OOM killer disabled.
639[ 314.519104] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
640[ 314.526419] printk: Suspending console(s) (use no_console_suspend to debug)
641bl30 get wakeup sources!
642process command 00000006
643bl30 enter suspend!
644cpu clk suspend rate 666000000
645store restore gp0 pll
646suspend_counter: 1
647Enter ddr suspend
648ddr suspend time: 16us
649alarm=5S
650process command 00000001
651cec ver:2018/04/19
652CEC cfg:0x0000
653exit_reason:0x03
654Enter ddr resume
655ddr resume time: 231us
656store restore gp0 pll
657cfg15 3b00100
658cfg15 33b00100
659cpu clk resume rate 500000000
660[ 314.536980] Disabling non-boot CPUs ...
661[ 314.537634] CPU1: shutdown
662[ 314.554263] psci: Retrying again to check for CPU kill
663[ 314.554269] psci: CPU1 killed.
664[ 314.555717] CPU2: shutdown
665[ 314.574247] psci: Retrying again to check for CPU kill
666[ 314.574252] psci: CPU2 killed.
667[ 314.575577] CPU3: shutdown
668[ 314.594256] psci: Retrying again to check for CPU kill
669[ 314.594262] psci: CPU3 killed.
670[ 314.595206] Enabling non-boot CPUs ...
671[ 314.595566] Detected VIPT I-cache on CPU1
672[ 314.595667] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
673[ 314.596443] CPU1 is up
674[ 314.596685] Detected VIPT I-cache on CPU2
675[ 314.596741] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
676[ 314.597378] CPU2 is up
677[ 314.597618] Detected VIPT I-cache on CPU3
678[ 314.597675] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
679[ 314.598359] CPU3 is up
680[ 314.602853] usb usb1: root hub lost power or was reset
681[ 314.602867] usb usb2: root hub lost power or was reset
682[ 314.793893] OOM killer enabled.
683[ 314.796990] Restarting tasks ... done.
684[ 314.800957] PM: suspend exit
685/sys/devices/system/cpu/cpufreq/policy0 #